1989 MAZDA 323 wheel bolt torque

Bl ON-VEHICLE MAINTENANCE
OIL SEAL LIP
L I I
OWOBX-063
05UOBX-069
Drive plate (ATX)
1. Hold the drive plate with the SST or equivalent.
2. Remove the drive plate lock bolts.
3. Remove the backing plate, drive plate, and adapter.
Oil seal
1. Cut the oil seal lip with a razor knife.
2. Remove the oil seal with a screwdriver protected with a rag.
Installation note
Oil seal
1. Apply a small amount of clean engine oil to the lip of a new
oil seal.
2. Push the oil seal slightly in by hand.
Caution
l The oil seal must be tapped in until it is flush with
the edge of the rear cover.
3. Tap the oil seal in evenly with a suitable pipe and a hammer.
Oil seal outer diameter: 1OOmm (3.94 in)
Flywheel (MTX)
1. Remove the sealant from the flywheel bolt holes in the crank-
shaft and from the flywheel bolts.
Caution
l If all the previous sealant cannot be removed from
a bolt, replace the bolt.
l Do not apply sealant if a new bolt is used.
2. Set the flywheel onto the crankshaft.
3. Apply sealant to the flywheel bolts and install them.
4. Hold the flywheel with the SST or equivalent.
5. Tighten the bolts in two or three steps in the order shown
in the figure.
Tightening torque:
96-103 N-m (9.6-10.5 m-kg, 71-76 ft-lb)

ASSEMBLY Bl
05UOBX.21’
OYJOBX-21
23UOBl-07
23UOBl-Ot
4. Apply a continuous bead of silicone sealant to the oil pan
along the inside of the bolt holes and overlap the ends.
5. Install the oil pan.
Tightening torque:
7.8-l 1 N,m (80-l 10 cm-kg, 89-95 in-lb)
End Plate
1. Install the end plate.
Tightening torque:
7.8-l 1 N,m (80-l 10 cm-kg, 89-95 in-lb)
Flywheel (MTX)
1, Remove the sealant from the flywheel bolt holes in the crank-
shaft and from the flywheel bolts.
Caution
l If all the previous sealant cannot be removed from
a bolt, replace the bolt.
l Do not apply sealant if a new bolt is used.
2. Set the flywheel onto the crankshaft.
3. Apply sealant to the flywheel bolts and install them.
4. Hold the flywheel with the
SST or equivalent.
5. Tighten the bolts in two or three steps in the order shown.
Tightening torque:
98-103 N+m (9.8-10.5 m-kg, 71-78 ft-lb)
Clutch Disc and Clutch Cover (MTX)
1. Install the clutch disc and clutch cover using the SST or
equivalent. (Refer to Section H.)
Tightening torque:
18-28 N.m (1.8-2.7 m-kg, 13-20 ft-lb)
B-l -77

ON-VEHICLE MAINTENANCE
Drive plate (ATX)
1. Hold the drive plate with the SST or equivalent.
2. Remove the drive plate lock bolts.
3. Remove the backing plate, drive plate, and adapter.
2311082-052
I
Oil seal
1. Cut the oil seal lip with a razor knife.
2. Remove the oil seal with a screwdriver protected with a rag.
I I
I
05UOBX-063
Installation note
Oil seal
1, Apply a small amount of clean engine oil to the lip of a new
oil seal.
2. Push the oil seal slightly in by hand.
OWOBX-069
APPLY SEALANT
03UOB2.04
Caution
l The oil seal must be tapped in untjl it is flush with
the edge of the rear cover.
3. Tap the oil seal in evenly with a suitable pipe and a hammer.
Oil seal outer diameter: 1OOmm (3.94 in)
Flywheel (MTX)
1. Remove the sealant from the flywheel bolt holes in the crank-
shaft and from the flywheel bolts.
Caution
l If all the previous sealant cannot be removed from
a bolt, replace the bolt.
l Do not apply sealant if a new bolt is used.
2. Set the flywheel onto the crankshaft.
3. Apply sealant to the flywheel bolts and install them.
4. Hold the flywheel with the
SST or equivalent.
5. Tighten the bolts in two or three steps in the order shown
in the figure.
Tightening torque:
1 96-103 N-m (9.6-10.5 m-kg, 71-76 ft-lb)
2311082-053
B2--29

B2 ASSEMBLY
I
03UOB2-09
I
05UOBX-20 6
9
OWOBX-211 0
05uoax-21 1
03UOB2-097
Oil Pan
1. Remove all foreign material from the contact surfaces.
2. Apply silicone sealant to the shaded areas shown in the
figure.
3. install new gaskets onto the oil pump body and the rear
cover with the projections in the notches shown in the figure.
4. Apply a continuous bead of silicone sealant to the oil pan
along the inside of the bolt holes and overlap the ends.
5. Install the oil pan.
Tightening torque:
7.8-l 1 N-m (80-l 10 cm-kg, 69-95 in-lb)
End Plate
1. Install the end plate.
Tightening torque:
7.8-l 1 N-m (80-l 10 cm-kg, 69-95 in-lb)
Flywheel (MTX)
1. Remove the sealant from the flywheel bolt holes in the crank-
shaft and from the flywheel bolts.
Caution
l If all the previous sealant cannot be removed from
a bolt, replace the bolt.
l Do not apply sealant if a new bolt is used.
2. Set the flywheel onto the crankshaft.
3. Apply sealant to the flywheel bolts and install them.
82-76

--
ASSEMBLY B2
2311082-06
2311082.04
1
03UO62-09!
J 2311062-063
4. Hold the flywheel with the SST or equivalent.
5. Tighten the bolts in two or three steps in the order shown.
Tightening torque:
96-l 03 N.m (9.6-10.5 m-kg, 71-76 ft-lb)
Clutch Disc and Clutch Cover (MTX)
1. Install the clutch disc and clutch cover using the SST or
equivalent. (Refer to Section H.)
Tightening torque:
16-26 N.m (1.8-2.7 m-kg, 13-20 ft-lb)
Drive Plate (ATX)
1. Remove the sealant from the drive plate holes in the crank-
shaft and from the drive plate lock bolts.
Caution
l If all the previous sealant cannot be removed from
a bolt, replace the bolt.
l Do not apply sealant if a new bolt is used.
2. Set the adapter, drive plate, and backing plate onto the
crankshaft.
3. Apply sealant to the drive plate bolts and install them.
4. Hold the drive plate with the
SST or equivalent.
5. Tighten the bolts in two or three steps in the order shown.
Tightening torque:
96-103 N.m (9.8-10.5 m-kg, 71-76 ft-lb)
Timing Belt Pulley
1, Reverse the direction of the SST or equivalent on the
flywheel.
2311082.064
B2-77

I 23UOB2-044
82 ASSEMBLY
DEFLECTION CHECKING POlNT
--; 11. Measure the timing belt deflection by applying moderate
oressure (98 N, 10 kg, 22 lb) midway between the two cam-
shaft pulleys.
If the deflection is not correct, repeat from Step 7 above.
Deflection:
9.0-11.5mm (0.35-0.45 in) at 98 N (10 kg, 22 lb)
Timing Belt Cover
1. Install the lower, middle, and upper covers.
Tightening torque:
7.8-11 N.m (80- ,110 cm-kg, 69-95 in-lb)
I 13EOB2-037
82-86
Pulley lock bolt
1. Hold the flywheel (MIX) or drive plate (ATX) with the SST
and tighten the pulley lock bolt.
Tlghtening torque:
157-167 N.m (16-17 m-kg, 116-123 ft-lb)
Cankshaft pully
1. Install the crankshaft pulley.
2. Install the plate.
3. Tighten the pulley bolts.
Tightening torque:
12-17 N-m (1.25-l -75 m-kg, 9-13 ft-lb)
Water Pump Pulley
1. Install the water pump pulley.
Tightening torque:
7.8-11 N*m (80-110 cm-kg, 69-95 in-lb)

H CLUTCH UNIT
/ 6fs 23UOHX-015
Removal Note
Clutch cover and disc
1. Install the SST or equivalent.
2. Loosen each bolt one turn at a time in a crisscross pattern
until spring tension is released. Then remove the clutch COV-
er and disc.
‘6
I
23UOHX-016
23UOHX-01
Pilot bearing
1. Remove the pilot bearing with the SST if necessary.
Flywheel
Note
l After removing the flywheel, inspect for oil leakage
past the crankshaft rear oil seal.
If necessary, replace the oil seal.
(Refer to Section B.) -J
1. Hold the flywheel with the SST or equivalent.
2. Remove the flywheel.
Installation Note
Flywheel
1. Wipe the bolts clean and apply sealant to the bolt threads.
2. Install the flywheel and the
SST or equivalent.
3. Tighten the bolts in the pattern shown.
Tightening torque:
96-103 N,m (9.6-10.5 m-kg, 71-76 ft-lb)
Pilot bearing
Note
l Install the pilot bearing flush with the flywheel.
1. Install the new bearing with a suitable pipe.
Bearing outer diameter: 35mm (1.376 in) .-’

CLUTCH UNIT, RELEASE BEARING, CLUTCH COVER, CLUTCH DISC H
L
13UOHX-01;
03UOHX-03 8
23UOHX-018
5
03UOHX-032
03UOHX-03
Clutch disc
1. Clean the clutch disc splines and main drive gear splines;
then apply organic molybdenum sulfide grease.
2. Hold the clutch disc in position with the
SST.
Clutch cover
1. Install the SST or equivalent.
2. Align the dowel holes with the flywheel dowels.
3. Tighten the bolts evenly and gradually in the pattern shown.
Tightening torque:
18-26 Nom (1.8-2.7 m-kg, 13-20 ft-lb)
RELEASE BEARING
INSPECTION
Note
l The clutch release bearing Is a sealed bearlng and
must not be washed in solvent.
1. Turn the bearing while applying force in the axial direction.
If the bearing sticks or has excessive resistance, replace it.
CLUTCH COVER
INSPECTION
Note
l Minor scoring or burning should be removed with
emery paper.
1. Inspect the contact surface of the clutch disc for scoring,
cracks, and burning. Repair or replace as necessary.
2. Inspect the contact surface of the clutch release bearing
for wear and cracks.
If there is wear or cracks, replace the clutch cover.
CLUTCH DISC
INSPECTION
Note
l Use sandpaper if the trouble is minor.
1. Inspect the lining surface for burning and oil contamination.
Replace the clutch disc if it is badly burned or oil soaked.
2. Inspect for loose facing rivets and rubbers.
Replace the clutch disc if either is loose.
H-17