1988 JEEP CHEROKEE parking brake
[x] Cancel search: parking brakePage 985 of 1378
![JEEP CHEROKEE 1988 Service Repair Manual Check Drive Shaft Seals
\b\
\
\
\
\
\](/manual-img/16/57037/w960_57037-984.png "JEEP CHEROKEE 1988 Service Repair Manual Check Drive Shaft Seals
\b\
\
\
\
\
\")
Check Drive Shaft Seals
\b\
\
\
\
\
\
\
Lubricate Ball Joints, Steering Linkage & Suspension
\b\
\
\
\
\
\
\
Lube Drive Shaft U-Joints and Slip Splines
\b\
\
\
\
\
\
\
Lube Front Axle Drive Joint and Pivot Bearings (4WD)
\b\
\
\
\
\
\
\
Lubricate Weatherstripping with Silicone
\b\
\
\
\
\
\
\
Lubricate Door Hinges
\b\
\
\
\
\
\
\
Lubricate Door Locks
\b\
\
\
\
\
\
\
Check Body Drain Holes
\b\
\
\
\
\
\
\
Rotate Tires and Adjust Air Pressure
\
\
\
\
\
\
\
Replace
\
\
\
\
\
\
\
Engine Oil
\b\
\
\
\
\
\
\
Oil Filter
\b\
\
\
\
\
\
\
Manual Transmission Fluid
\b\
\
\
\
\
\
\
Automatic Transmission Fluid, Filter and Adjust Bands
\b\
\
\
\
\
\
\
Transfer Case Fluid
\b\
\
\
\
\
\
\
Flush and Fill Engine Coolant, if not done in last 24 months
\
\
\
\
\
\
\
Lubrication Specifications
\
\
\
\
\
\
\
Application Specification
Automatic Transmission .......................... Dexron-IIE ATF
Brake Master Cylinder .......... DOT 3 (SAE J-1703F) Brake Fluid
Engine Coolant ........... Alugard 340-2 & Water (50/50 Mixture)
Engine Oil (
1)
Gasoline Engine
Temperature Range
Above 30
F (-1
C) ........ SAE 20W-40 Or 20W-50 API SH/CD
Above 0
F (-18
C) ......... SAE 10W-30 Or 10W-40 API SH/CD
Less Than 60
F (16
C) ............... SAE 5W-30 API SH/CD
Drive Axles ................................ SAE 75W-90 API GL-5
Drive Axles (Trac-Lok) (
2) ................ SAE 80W-140 API GL-5
Drive Axles (Trailer Towing) .............. SAE 80W-140 API GL-5
Hydraulic Clutch ............... DOT 3 (SAE J-1703F) Brake Fluid
Manual Transmission ........................ SAE 75W-90 API GL-5
Parking Brake Cable Guides ................. NLGI Grade 2, GC-LB
Door & Hood Hinges ............................ Light Engine Oil
Manual Steering Box ............... Multi-Purpose NLGI Grade 2EP
Power Steering Pump ....................... Power Steering Fluid
Transfer Case ................................... Dexron-IIE ATF
Brake Caliper Bushings ........ GE 661 or DOW 111 Silicone Grease
Caliper Slide Pins ........... GE 661 or DOW 111 Silicone Grease
Wheel Bearings .................. Multi-Purpose NLGI Grade GC-LB
Drive Shaft U-Joints .............. Multi-Purpose NLGI Grade 2EP
Steering Linkage (
4)( 5) .................... NLGI Grade 2, GC-LB
Ball Joints (
4)( 6) ......................... NLGI Grade 2, GC-LB
Weatherstrip .......................... Silicone Spray Lubricant
Wheel Lug Nut Torque ...................... 95 ft. lbs. (129 N.m)
Page 987 of 1378
![JEEP CHEROKEE 1988 Service Repair Manual 82,500 MILE (132,000 KM) SERVICE
82,500 MILE (132,000 KM) SERVICE \
\
\
\
\
\](/manual-img/16/57037/w960_57037-986.png "JEEP CHEROKEE 1988 Service Repair Manual 82,500 MILE (132,000 KM) SERVICE
82,500 MILE (132,000 KM) SERVICE \
\
\
\
\
\")
82,500 MILE (132,000 KM) SERVICE
82,500 MILE (132,000 KM) SERVICE \
\
\
\
\
\
\
Service Or Inspect
\
\
\
\
\
\
\
Verify Last Major Service Was Performed
\b\
\
\
\
\
\
\
Check Fluid Levels
\b\
\
\
\
\
\
\
Check Cooling System Hoses and Clamps
\b\
\
\
\
\
\
\
Check Exhaust System & Heat Shielding
\b\
\
\
\
\
\
\
Inspect Brake System
\b\
\
\
\
\
\
\
Inspect C/V Joint boots (4WD)
\b\
\
\
\
\
\
\
Inspect Underside of Vehicle (Bolts & Threaded Fasteners)
\b\
\
\
\
\
\
\
Check/Lube Manual Steering Gear
\b\
\
\
\
\
\
\
Check Drive Shaft Seals
\b\
\
\
\
\
\
\
Lubricate Ball Joints, Steering Linkage & Suspension
\b\
\
\
\
\
\
\
Lube Drive Shaft U-Joints and Slip Splines
\b\
\
\
\
\
\
\
Lube Front Axle Drive Joint and Pivot Bearings (4WD)
\b\
\
\
\
\
\
\
Rotate Tires and Adjust Air Pressure (Including Spare)
\
\
\
\
\
\
\
Replace
\
\
\
\
\
\
\
Engine Oil
\b\
\
\
\
\
\
\
Oil Filter, if it has not been changed in the last 12 months
\b\
\
\
\
\
\
\
O2 Sensor (1987-89)
\b\
\
\
\
\
\
\
Flush and Fill Engine Coolant, if not done in last 24 months
\
\
\
\
\
\
\
Lubrication Specifications
\
\
\
\
\
\
\
Application Specification
Automatic Transmission .......................... Dexron-IIE ATF
Brake Master Cylinder .......... DOT 3 (SAE J-1703F) Brake Fluid
Engine Coolant ........... Alugard 340-2 & Water (50/50 Mixture)
Engine Oil (
1)
Gasoline Engine
Temperature Range
Above 30
F (-1
C) ........ SAE 20W-40 Or 20W-50 API SH/CD
Above 0
F (-18
C) ......... SAE 10W-30 Or 10W-40 API SH/CD
Less Than 60
F (16
C) ............... SAE 5W-30 API SH/CD
Drive Axles ................................ SAE 75W-90 API GL-5
Drive Axles (Trac-Lok) (
2) ................ SAE 80W-140 API GL-5
Drive Axles (Trailer Towing) .............. SAE 80W-140 API GL-5
Hydraulic Clutch ............... DOT 3 (SAE J-1703F) Brake Fluid
Manual Transmission ........................ SAE 75W-90 API GL-5
Parking Brake Cable Guides ................. NLGI Grade 2, GC-LB
Door & Hood Hinges ............................ Light Engine Oil
Page 989 of 1378
Rear (Trac-Lok) (4) .......................... 2.5 Pts. (1.2L)
(
1) - Capacities are recommended or calculated levels. Always use
dipstick (if available) to measure level.
(
2) - Includes 2.3 qts. for coolant recovery bottle.
(
3) - Fill to bottom of filler plug hole.
(
4) - Add 4 ozs. (118 ml) of Limited-Slip differential lubricant
additive first, then add new fluid.
\
\
\
\
\
\
\
\f
90,000 MILE (144,000 KM) SERVICE
90,000 MILE (144,000 KM) SERVICE \
\
\
\
\
\
\
Service Or Inspect
\
\
\
\
\
\
\
Verify Last Major Service Was Performed
\b\
\
\
\
\
\
\
Check Fluid Levels
\b\
\
\
\
\
\
\
Check Fuel Lines, Connections
\b\
\
\
\
\
\
\
Check Cooling System Hoses and Clamps
\b\
\
\
\
\
\
\
Check Coolant Strength
\b\
\
\
\
\
\
\
Clean Battery and Battery Terminals
\b\
\
\
\
\
\
\
Accessory Drive Belts
\b\
\
\
\
\
\
\
Clean Choke Linkage
\b\
\
\
\
\
\
\
Check Exhaust System & Heat Shielding
\b\
\
\
\
\
\
\
Check Operation of Horn, Wipers/Washers & All Exterior Lights
\b\
\
\
\
\
\
\
Inspect Condition of Wiper Blades
\b\
\
\
\
\
\
\
Check Headlight Alignment
\b\
\
\
\
\
\
\
Check Seat Belt Webbing and Release Mechanisms
\b\
\
\
\
\
\
\
Check Parking Brake Operation
\b\
\
\
\
\
\
\
Check Shift/Clutch Interlock Operation
\b\
\
\
\
\
\
\
Adjust Drive Belt Tension
\b\
\
\
\
\
\
\
Inspect C/V Joint boots (4WD)
\b\
\
\
\
\
\
\
Inspect Underside of Vehicle (Bolts & Threaded Fasteners)
\b\
\
\
\
\
\
\
Check/Lube Manual Steering Gear
\b\
\
\
\
\
\
\
Check Drive Shaft Seals
\b\
\
\
\
\
\
\
Lubricate Ball Joints, Steering Linkage & Suspension
\b\
\
\
\
\
\
\
Lube Drive Shaft U-Joints and Slip Splines
\b\
\
\
\
\
\
\
Lube Front Axle Drive Joint and Pivot Bearings (4WD)
\b\
\
\
\
\
\
\
Page 990 of 1378
![JEEP CHEROKEE 1988 Service Repair Manual Lube Parking Brake Ratio Lever Pivot
\b\
\
\
\
\
\](/manual-img/16/57037/w960_57037-989.png "JEEP CHEROKEE 1988 Service Repair Manual Lube Parking Brake Ratio Lever Pivot
\b\
\
\
\
\
\")
Lube Parking Brake Ratio Lever Pivot
\b\
\
\
\
\
\
\
Lube Manual Gearshift Control (4WD Transfer Case)
\b\
\
\
\
\
\
\
Inspect/Repack Front Wheel Bearings (2WD Models)
\b\
\
\
\
\
\
\
Inspect Front Brake Pads & Rotors
\b\
\
\
\
\
\
\
Lubricate Caliper Slide Rails
\b\
\
\
\
\
\
\
Inspect Rear Brake Linings & Drums
\b\
\
\
\
\
\
\
Inspect Brake System Hoses & Lines
\b\
\
\
\
\
\
\
Inspect Shocks for Leakage
\b\
\
\
\
\
\
\
Inspect Tire Wear Pattern
\b\
\
\
\
\
\
\
Lubricate Weatherstripping with Silicone
\b\
\
\
\
\
\
\
Lubricate Door Hinges
\b\
\
\
\
\
\
\
Lubricate Door Locks
\b\
\
\
\
\
\
\
Check Body Drain Holes
\b\
\
\
\
\
\
\
Rotate Tires and Adjust Air Pressure
\
\
\
\
\
\
\
Replace
\
\
\
\
\
\
\
Engine Oil
\b\
\
\
\
\
\
\
Oil Filter
\b\
\
\
\
\
\
\
Air Filter Element
\b\
\
\
\
\
\
\
Fuel Filter
\b\
\
\
\
\
\
\
Spark Plugs
\b\
\
\
\
\
\
\
Automatic Transmission Fluid, Filter and Adjust Bands
\b\
\
\
\
\
\
\
PCV Filter
\b\
\
\
\
\
\
\
PCV Valve (
1) ( 2)
\b\
\
\
\
\
\
\
Drive Belt (V-Type) (
2) ( 3)
\
\
\
\
\
\
\
(
1) - Replacement is recommended by Chrysler at this time, but it
is not required to maintain the warranty on the PCV valve.
(
2) - Not required, if belt or PCV Valve was previously replaced
(
3) - Check and replace as needed.
\
\
\
\
\
\
\
Lubrication Specifications
\
\
\
\
\
\
\
Application Specification
Automatic Transmission .......................... Dexron-IIE ATF
Brake Master Cylinder .......... DOT 3 (SAE J-1703F) Brake Fluid
Engine Coolant ........... Alugard 340-2 & Water (50/50 Mixture)
Engine Oil (
1)
Gasoline Engine
Temperature Range
Page 991 of 1378
Above 30
F (-1
C) ........ SAE 20W-40 Or 20W-50 API SH/CD
Above 0
F (-18
C) ......... SAE 10W-30 Or 10W-40 API SH/CD
Less Than 60
F (16
C) ............... SAE 5W-30 API SH/CD
Drive Axles ................................ SAE 75W-90 API GL-5
Drive Axles (Trac-Lok) (
2) ................ SAE 80W-140 API GL-5
Drive Axles (Trailer Towing) .............. SAE 80W-140 API GL-5
Hydraulic Clutch ............... DOT 3 (SAE J-1703F) Brake Fluid
Manual Transmission ........................ SAE 75W-90 API GL-5
Parking Brake Cable Guides ................. NLGI Grade 2, GC-LB
Door & Hood Hinges ............................ Light Engine Oil
Manual Steering Box ............... Multi-Purpose NLGI Grade 2EP
Power Steering Pump ....................... Power Steering Fluid
Transfer Case ................................... Dexron-IIE ATF
Brake Caliper Bushings ........ GE 661 or DOW 111 Silicone Grease
Caliper Slide Pins ........... GE 661 or DOW 111 Silicone Grease
Wheel Bearings .................. Multi-Purpose NLGI Grade GC-LB
Drive Shaft U-Joints .............. Multi-Purpose NLGI Grade 2EP
Steering Linkage (
4)( 5) .................... NLGI Grade 2, GC-LB
Ball Joints (
4)( 6) ......................... NLGI Grade 2, GC-LB
Weatherstrip .......................... Silicone Spray Lubricant
Wheel Lug Nut Torque ...................... 95 ft. lbs. (129 N.m)
(
1) - SAE 10W-30 SH/CD is preferred.
(
2) - Add 4 ozs. (118 ml) of Limited-Slip differential lubricant
additive when changing fluid.
(
3) - For vehicles operating under heavy-duty towing conditions,
use SAE 75W-140 Synthetic lube.
NOTE: Before using SAE 75W-140 Synthetic the old fluid must
be DRAINED and FLUSHED with clean mineral based axle
lubricant. Then refill with new synthetic lube.
(
4) - Use low pressure grease gun to prevent seal damage.
(
5) - Fill until lubricant squeezes out from the base of seals.
(
6) - Fill ball joint until seal starts to swell.
\
\
\
\
\
\
\
Fluid Capacities
\
\
\
\
\
\
\
Application ( 1) Quantity
Automatic Transmission
1984-86 (904 HD)
Fluid Change ............................... 4.0 Qts. (3.8L)
Overhaul (Dry Fill) ........................ 8.0 Qts. (7.6L) \
1987-88
Fluid Change ............................... 4.0 Qts. (3.8L)
Overhaul (Dry Fill) ........................ 8.5 Qts. (8.0L) \
Cooling System (
2)
4-Cylinder .................................. 10.0 Qts. (9.5L)
6-Cylinder ................................. 12.0 Qts. (11.4L)
Engine Oil
4-Cylinder ................................... 4.0 Qts. (3.8L)
6-Cylinder ................................... 6.0 Qts. (5.7L)
Fuel Tank
Standard .................................. 13.5 Gals. (51.1L)
Optional .................................... 20 Gals. (75.7L)
Manual Transmission (
3)
AX4 (AISIN) .................................. 7.4 Pts. (3.5L) \
T4 (Borg-Warner) ............................. 3.9 Pts. (1.8L) \
AX5 (AISIN) .................................. 7.0 Pts. (3.3L) \
T5 (Borg-Warner) ............................. 4.5 Pts. (2.1L) \
Transfer Case
1985-86
Selec-Trac (229 Full-Time) ................. 6.0 Pts. (2.8L) \
Command-Trac (Part-Time 207) ............... 4.5 Pts. (2.1L) \
Page 993 of 1378
![JEEP CHEROKEE 1988 Service Repair Manual Lubricate Ball Joints, Steering Linkage & Suspension
\b\
\
\
\
\
\](/manual-img/16/57037/w960_57037-992.png "JEEP CHEROKEE 1988 Service Repair Manual Lubricate Ball Joints, Steering Linkage & Suspension
\b\
\
\
\
\
\")
Lubricate Ball Joints, Steering Linkage & Suspension
\b\
\
\
\
\
\
\
Lube Drive Shaft U-Joints and Slip Splines
\b\
\
\
\
\
\
\
Lube Front Axle Drive Joint and Pivot Bearings (4WD)
\b\
\
\
\
\
\
\
Rotate Tires and Adjust Air Pressure (Including Spare)
\
\
\
\
\
\
\
Replace
\
\
\
\
\
\
\
Engine Oil
\b\
\
\
\
\
\
\
Oil Filter, if it has not been changed in the last 12 months
\
\
\
\
\
\
\
Lubrication Specifications
\
\
\
\
\
\
\
Application Specification
Automatic Transmission .......................... Dexron-IIE ATF
Brake Master Cylinder .......... DOT 3 (SAE J-1703F) Brake Fluid
Engine Coolant ........... Alugard 340-2 & Water (50/50 Mixture)
Engine Oil (
1)
Gasoline Engine
Temperature Range
Above 30
F (-1
C) ........ SAE 20W-40 Or 20W-50 API SH/CD
Above 0
F (-18
C) ......... SAE 10W-30 Or 10W-40 API SH/CD
Less Than 60
F (16
C) ............... SAE 5W-30 API SH/CD
Drive Axles ................................ SAE 75W-90 API GL-5
Drive Axles (Trac-Lok) (
2) ................ SAE 80W-140 API GL-5
Drive Axles (Trailer Towing) .............. SAE 80W-140 API GL-5
Hydraulic Clutch ............... DOT 3 (SAE J-1703F) Brake Fluid
Manual Transmission ........................ SAE 75W-90 API GL-5
Parking Brake Cable Guides ................. NLGI Grade 2, GC-LB
Door & Hood Hinges ............................ Light Engine Oil
Manual Steering Box ............... Multi-Purpose NLGI Grade 2EP
Power Steering Pump ....................... Power Steering Fluid
Transfer Case ................................... Dexron-IIE ATF
Brake Caliper Bushings ........ GE 661 or DOW 111 Silicone Grease
Caliper Slide Pins ........... GE 661 or DOW 111 Silicone Grease
Wheel Bearings .................. Multi-Purpose NLGI Grade GC-LB
Drive Shaft U-Joints .............. Multi-Purpose NLGI Grade 2EP
Steering Linkage (
4)( 5) .................... NLGI Grade 2, GC-LB
Ball Joints (
4)( 6) ......................... NLGI Grade 2, GC-LB
Weatherstrip .......................... Silicone Spray Lubricant
Wheel Lug Nut Torque ...................... 95 ft. lbs. (129 N.m)
(
1) - SAE 10W-30 SH/CD is preferred.
(
2) - Add 4 ozs. (118 ml) of Limited-Slip differential lubricant
additive when changing fluid.
(
3) - For vehicles operating under heavy-duty towing conditions,
use SAE 75W-140 Synthetic lube.
NOTE: Before using SAE 75W-140 Synthetic the old fluid must
be DRAINED and FLUSHED with clean mineral based axle
lubricant. Then refill with new synthetic lube.
(
4) - Use low pressure grease gun to prevent seal damage.
(
5) - Fill until lubricant squeezes out from the base of seals.
(
6) - Fill ball joint until seal starts to swell.
\
\
\
\
\
\
\
Fluid Capacities
\
\
\
\
\
\
\
Application ( 1) Quantity
Automatic Transmission
Page 995 of 1378
![JEEP CHEROKEE 1988 Service Repair Manual Clean Battery and Battery Terminals
\b\
\
\
\
\
\](/manual-img/16/57037/w960_57037-994.png "JEEP CHEROKEE 1988 Service Repair Manual Clean Battery and Battery Terminals
\b\
\
\
\
\
\")
Clean Battery and Battery Terminals
\b\
\
\
\
\
\
\
Inspect Brake System
\b\
\
\
\
\
\
\
Check Operation of Horn, Wipers/Washers & All Exterior Lights
\b\
\
\
\
\
\
\
Inspect Condition of Wiper Blades
\b\
\
\
\
\
\
\
Check Headlight Alignment
\b\
\
\
\
\
\
\
Check Seat Belt Webbing and Release Mechanisms
\b\
\
\
\
\
\
\
Check Parking Brake Operation
\b\
\
\
\
\
\
\
Check Shift/Clutch Interlock Operation
\b\
\
\
\
\
\
\
Inspect C/V Joint boots (4WD)
\b\
\
\
\
\
\
\
Inspect Underside of Vehicle (Bolts & Threaded Fasteners)
\b\
\
\
\
\
\
\
Check/Lube Manual Steering Gear
\b\
\
\
\
\
\
\
Check Drive Shaft Seals
\b\
\
\
\
\
\
\
Lubricate Ball Joints, Steering Linkage & Suspension
\b\
\
\
\
\
\
\
Lube Drive Shaft U-Joints and Slip Splines
\b\
\
\
\
\
\
\
Lube Front Axle Drive Joint and Pivot Bearings (4WD)
\b\
\
\
\
\
\
\
Inspect Front Wheel Bearings (4WD)
\b\
\
\
\
\
\
\
Lubricate Weatherstripping with Silicone
\b\
\
\
\
\
\
\
Lubricate Door Hinges
\b\
\
\
\
\
\
\
Lubricate Door Locks
\b\
\
\
\
\
\
\
Check Body Drain Holes
\b\
\
\
\
\
\
\
Rotate Tires and Adjust Air Pressure
\
\
\
\
\
\
\
Replace
\
\
\
\
\
\
\
Engine Oil
\b\
\
\
\
\
\
\
Oil Filter
\b\
\
\
\
\
\
\
Flush and Fill Engine Coolant, if not done in last 24 months
\
\
\
\
\
\
\
Lubrication Specifications
\
\
\
\
\
\
\
Application Specification
Automatic Transmission .......................... Dexron-IIE ATF
Brake Master Cylinder .......... DOT 3 (SAE J-1703F) Brake Fluid
Engine Coolant ........... Alugard 340-2 & Water (50/50 Mixture)
Engine Oil (
1)
Gasoline Engine
Temperature Range
Above 30
F (-1
C) ........ SAE 20W-40 Or 20W-50 API SH/CD
Above 0
F (-18
C) ......... SAE 10W-30 Or 10W-40 API SH/CD
Less Than 60
F (16
C) ............... SAE 5W-30 API SH/CD
Page 996 of 1378
Drive Axles ................................ SAE 75W-90 API GL-5
Drive Axles (Trac-Lok) (
2) ................ SAE 80W-140 API GL-5
Drive Axles (Trailer Towing) .............. SAE 80W-140 API GL-5
Hydraulic Clutch ............... DOT 3 (SAE J-1703F) Brake Fluid
Manual Transmission ........................ SAE 75W-90 API GL-5
Parking Brake Cable Guides ................. NLGI Grade 2, GC-LB
Door & Hood Hinges ............................ Light Engine Oil
Manual Steering Box ............... Multi-Purpose NLGI Grade 2EP
Power Steering Pump ....................... Power Steering Fluid
Transfer Case ................................... Dexron-IIE ATF
Brake Caliper Bushings ........ GE 661 or DOW 111 Silicone Grease
Caliper Slide Pins ........... GE 661 or DOW 111 Silicone Grease
Wheel Bearings .................. Multi-Purpose NLGI Grade GC-LB
Drive Shaft U-Joints .............. Multi-Purpose NLGI Grade 2EP
Steering Linkage (
4)( 5) .................... NLGI Grade 2, GC-LB
Ball Joints (
4)( 6) ......................... NLGI Grade 2, GC-LB
Weatherstrip .......................... Silicone Spray Lubricant
Wheel Lug Nut Torque ...................... 95 ft. lbs. (129 N.m)
(
1) - SAE 10W-30 SH/CD is preferred.
(
2) - Add 4 ozs. (118 ml) of Limited-Slip differential lubricant
additive when changing fluid.
(
3) - For vehicles operating under heavy-duty towing conditions,
use SAE 75W-140 Synthetic lube.
NOTE: Before using SAE 75W-140 Synthetic the old fluid must
be DRAINED and FLUSHED with clean mineral based axle
lubricant. Then refill with new synthetic lube.
(
4) - Use low pressure grease gun to prevent seal damage.
(
5) - Fill until lubricant squeezes out from the base of seals.
(
6) - Fill ball joint until seal starts to swell.
\
\
\
\
\
\
\
Fluid Capacities
\
\
\
\
\
\
\
Application ( 1) Quantity
Automatic Transmission
1984-86 (904 HD)
Fluid Change ............................... 4.0 Qts. (3.8L)
Overhaul (Dry Fill) ........................ 8.0 Qts. (7.6L) \
1987-88
Fluid Change ............................... 4.0 Qts. (3.8L)
Overhaul (Dry Fill) ........................ 8.5 Qts. (8.0L) \
Cooling System (
2)
4-Cylinder .................................. 10.0 Qts. (9.5L)
6-Cylinder ................................. 12.0 Qts. (11.4L)
Engine Oil
4-Cylinder ................................... 4.0 Qts. (3.8L)
6-Cylinder ................................... 6.0 Qts. (5.7L)
Fuel Tank
Standard .................................. 13.5 Gals. (51.1L)
Optional .................................... 20 Gals. (75.7L)
Manual Transmission (
3)
AX4 (AISIN) .................................. 7.4 Pts. (3.5L) \
T4 (Borg-Warner) ............................. 3.9 Pts. (1.8L) \
AX5 (AISIN) .................................. 7.0 Pts. (3.3L) \
T5 (Borg-Warner) ............................. 4.5 Pts. (2.1L) \
Transfer Case
1985-86
Selec-Trac (229 Full-Time) ................. 6.0 Pts. (2.8L) \
Command-Trac (Part-Time 207) ............... 4.5 Pts. (2.1L) \
1987
Selec-Trac ................................. 2.5 Pts. (1.2L)
Command-Trac ............................... 2.2 Pts. (1.0L)