1988 JEEP CHEROKEE sensor
[x] Cancel search: sensorPage 1131 of 1378
\003
* S U SPEN SIO N U NIF O RM IN SPEC TIO N G UID ELIN ES *
1 988 J e ep C hero ke e
GENERAL INFORMATION
Steering, Suspension, Wheel Alignment, Wheels and Tires
Motorist Assurance Program
Standards For Automotive Repair
All Makes and Models
INTRODUCTION TO MOTORIST ASSURANCE PROGRAM (MAP)
CONTENTS
Motorist Assurance Program (MAP)
OVERVIEW
OVERVIEW OF SERVICE REQUIREMENTS & SUGGESTIONS
Steering and Suspension
AIR RIDE SUSPENSION
AIR RIDE SUSPENSION - AIR SHOCKS AND AIR STRUTS
AIR RIDE SUSPENSION - AIR SPRING VALVES
AIR RIDE SUSPENSION - AIR SPRINGS
AIR RIDE SUSPENSION - COMPRESSORS
AIR RIDE SUSPENSION - HEIGHT SENSORS
AIR RIDE SUSPENSION - MODULES
AIR RIDE SUSPENSION - RELAYS (COMPRESSOR)
AIR RIDE SUSPENSION - SWITCHES (ON/OFF)
AIR RIDE SUSPENSION - TORSION SPRINGS (COUNTER BALANCING)
AIR RIDE SUSPENSION - TUBING
AIR RIDE SUSPENSION - WARNING LAMPS
AIR RIDE SUSPENSION - WIRING HARNESSES
BALL JOINTS
BUSHINGS
CENTER LINKS
CONTROL ARM SHAFTS
CONTROL ARMS
DRAG LINKS
ELECTRONIC RIDE CONTROL SHOCKS AND STRUTS
IDLER ARMS
KING PINS
PITMAN ARMS
POWER STEERING HOSES
POWER STEERING (HYDRAULIC) PUMPS
RADIUS ARMS
RELAY RODS
SHOCK ABSORBERS, STRUT CARTRIDGES AND STRUT ASSEMBLIES
SPINDLES
SPRINGS - COIL, LEAF AND TORSION BAR
STEEL POWER STEERING LINES
STEERING ARMS
STEERING DAMPERS
STEERING GEARS (EXCEPT RACK AND PINION)
STEERING GEARS - RACK AND PINION
STEERING KNUCKLES
STRIKE OUT BUMPERS
STRUT RODS
STRUT UPPER BEARING PLATE ASSEMBLIES
SWAY BAR LINKS
SWAY BARS
Page 1137 of 1378
![JEEP CHEROKEE 1988 Service Repair Manual AIR RIDE SUSPENSION - COMPRESSORS
AIR RIDE SUSPENSION - COMPRESSOR INSPECTION \
\
\
\
\](/manual-img/16/57037/w960_57037-1136.png "JEEP CHEROKEE 1988 Service Repair Manual AIR RIDE SUSPENSION - COMPRESSORS
AIR RIDE SUSPENSION - COMPRESSOR INSPECTION \
\
\
\
\")
AIR RIDE SUSPENSION - COMPRESSORS
AIR RIDE SUSPENSION - COMPRESSOR INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware bent . B ... Require repair or replacement
of bent part.
Attaching hardware
broken ................. A ... Require replacement of broken
part.
Attaching hardware
loose .................. A ... Require repair or replacement
of loose part.
Attaching hardware
missing ................ C .. Require replacement of missing
part.
Attaching hardware
threads damaged ........ A ... Require repair or replacement
of part with damaged threads.
Attaching hardware
threads stripped
(threads missing) ...... A ..... Require replacement of part
with stripped threads.
Connector bent .......... A .. Require repair or replacement.
Connector broken ........ A ............ Require replacement.
Connector loose ......... A .. Require repair or replacement.
Does not build pressure . A .......... ( 1) Further inspection
required.
Excessive run time ...... B .......... ( 2) Further inspection
required.
Inoperative ............. A ............ Require replacement.
Leaking ................. A .. Require repair or replacement.
Missing ................. C ............ Require replacement.
( 1) - If failure to build pressure is traced to the
compressor, require replacement.
( 2) - If excessive run time is traced to the compressor,
require replacement.
\
\
\
\
\
\
\
AIR RIDE SUSPENSION - HEIGHT SENSORS
AIR RIDE SUSPENSION - HEIGHT SENSOR INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware bent . B ... Require repair or replacement
of bent part.
Attaching hardware
broken ................. A ... Require replacement of broken
part.
Attaching hardware
corroded, affecting
structural integrity .... A .......... Require replacement of
corroded part.
Attaching hardware
loose .................. A ... Require repair or replacement
of loose part.
Attaching hardware
missing ................ C .. Require replacement of missing
part.
Attaching hardware
Page 1138 of 1378
threads damaged ........ A ... Require repair or replacement
of part with damaged threads.
Attaching hardware
threads stripped
(threads missing) ...... A ..... Require replacement of part
with stripped threads.
Dust boot missing ....... 2 ........ (1) Suggest replacement.
Dust boot split ......... 2 ........ ( 1) Suggest replacement.
Dust boot torn .......... 2 ........ ( 1) Suggest replacement.
Housing cracked ......... A ............ Require replacement.
Lead routing incorrect .. B .. Require rerouting according to
vehicle manufacturer's
specifications.
Loose ................... B ... Require adjustment to vehicle
manufacturer's specifications.
Missing ................. C ............ Require replacement.
Output signal incorrect . A .. Require repair or replacement.
Wire lead damaged ....... A .. Require repair or replacement.
( 1) - This condition can lead to damage of the sliding magnet,
which, in turn, causes premature sensor failure.
\
\
\
\
\
\
\
AIR RIDE SUSPENSION - MODULES
AIR RIDE SUSPENSION - MODULE INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Attaching hardware
loose .................. A ... Require repair or replacement
of loose part.
Attaching hardware
missing ................ C .. Require replacement of missing
part.
Attaching hardware
threads damaged ........ A ... Require repair or replacement
of part with damaged threads.
Attaching hardware
threads stripped
(threads missing) ...... A ..... Require replacement of part
with stripped threads.
Housing cracked ......... 2 .. Suggest repair or replacement.
Inoperative ............. A ............ Require replacement.
Missing ................. C ............ Require replacement.
\
\
\
\
\
\
\
AIR RIDE SUSPENSION - RELAYS (COMPRESSOR)
AIR RIDE SUSPENSION - RELAY (COMPRESSOR) INSPECTION \
\
\
\
\
\
\
Condition Code Procedure
Housing cracked ......... 2 ........ ( 1) Suggest replacement.
Intermittent ............ A ............ Require replacement.
Missing ................. C ............ Require replacement.
Output signal incorrect . A ............ Require replacement.
( 1) - If moisture enters the relay, it can reduce life
expectancy or impair function.
\
\
\
\
\
\
\
AIR RIDE SUSPENSION - SWITCHES (ON/OFF)
Page 1199 of 1378
Will Not Shift Or Difficult To Shift Into Gear
Vehicle speed too high; slow vehicle to 2-3 MPH to shift.
Vehicle operated too long on dry paved surface; stop vehicle and place
in Reverse or Neutral to relieve driveline torque. Ensure transfer
case external linkage is not binding. Ensure correct fluid is used.
Internal parts may be worn or damaged.
Noisy In All Gears
Check fluid level. Ensure correct fluid is used. If fluid is
okay, locate possible internal mechanical problem.
Jumps Out Of Gear Or Noisy In 4WD
Transfer case not completely in gear; check shift linkage.
Range fork damaged. Shift fork pads are worn or shift fork binding.
Low range gear worn.
Fluid Leaking From Vent Or Seals
Transfer case overfilled. Vent plugged. Output shaft seals
are damaged or not installed properly.
ON-VEHICLE SERVICE
FRONT OIL SEAL
Removal & Installation
1) Mark front drive shaft and flange for installation
alignment reference. Remove front drive shaft. Remove flange. Discard
washer and nut. Using a screwdriver, carefully remove oil seal. Ensure
seal contact surface is clean.
2) Apply ATF to seal lip and flange seal surface. Install NEW
oil seal. Install flange and NEW washer and nut. Tighten nut to
specifications. See TORQUE SPECIFICATIONS . Install front drive shaft
using alignment marks. Check transfer case fluid.
EXTENSION HOUSING OIL SEAL & BUSHING
Removal & Installation
1) Mark rear drive shaft and flange for installation
alignment reference. Remove rear drive shaft. Tap extension housing in
a clockwise direction and remove extension housing. DO NOT pry on
extension housing. Using a screwdriver, remove oil seal from extension
housing.
2) Using bushing driver, replace bushing in extension
housing. Install NEW extension housing oil seal. Apply silicone
sealant to extension housing mating surface. Install extension
housing. To complete installation, reverse removal procedure.
REMOVAL & INSTALLATION
TRANSFER CASE
Removal
1) Shift transfer case into 4H and disconnect battery
negative cable. Raise vehicle, remove skid plate and drain fluid.
2) Mark front and rear output shaft yokes to drive shafts for
reassembly reference. Support transfer case and remove rear
crossmember. Remove drive shafts.
3) Disconnect vehicle speed sensor electrical connector and
vacuum (hoses) harness at transfer case. Remove shift lever or linkage\
rod from case. Remove transfer case attaching bolts. Remove transfer
case from vehicle.
Page 1200 of 1378
Installation
1) Clean all old gasket material from transmission and
transfer case mating surfaces. Position NEW gasket on transfer case
with orientation tab at upper left bolt hole.
2) Install transfer case, aligning splines of input shaft
with transmission. Slide transfer case forward until seated against
transmission. Install transfer case attaching bolts and tighten to
specification. See TORQUE SPECIFICATIONS . Install rear crossmember.
3) Attach shift lever and connect speed sensor electrical
connector and vacuum harness at transfer case. Using reference marks
made during removal, reinstall front and rear drive shafts. Refill
transfer case. Install skid plate and lower vehicle. Connect negative
battery cable. Road test vehicle.
TRANSFER CASE DISASSEMBLY
1) Remove front companion yoke. See Fig. 2 or 3. Discard
washer and nut. Shift transfer case to 4L and remove extension
housing. Remove rear bearing snap ring. Using 2 screwdrivers under
each tab, remove retainer housing. Remove rear case and oil pump as an
assembly.
2) Remove oil pump pick-up screen and tube from rear case.
Remove oil pump. Remove "O" ring from oil pump and discard. DO NOT
separate oil pump halves. Pump must be replaced as an assembly if
necessary.
3) Remove mode spring. Using a soft hammer, tap front output
shaft upward and remove with drive chain as an assembly. Remove
mainshaft, mode fork and shift rail as an assembly. Remove mode fork
and shift rail from synchronizer sleeve.
4) Mark synchronizer sleeve position for reassembly
reference. Remove synchronizer sleeve from mainshaft. Remove
synchronizer hub snap ring. Remove synchronizer hub, stop ring and
drive sprocket. Slide range fork pin out of sector.
5) Remove range fork and shift hub as an assembly. Remove
range lever from sector shaft. Remove shift sector, bushing and "O"
ring. Remove shift detent pin, spring and plug. Remove front bearing
retainer. Remove input gear snap ring.
6) Press input and low range gear assembly from input gear
bearing. Remove low range gear snap ring. Remove input gear retainer,
thrust washers and input gear from low range gear.
7) Remove all oil seals. Remove magnet from front case.
Remove front bearing snap ring. Using a plastic hammer, remove front
bearing. Press input gear bearing from front case.
8) Using slide hammer and internal puller, remove input gear
pilot bearing. Press bearings from drive sprocket. Using internal
puller and slide hammer, remove output shaft rear bearing.
Page 1205 of 1378
![JEEP CHEROKEE 1988 Service Repair Manual TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS TABLE \
\
\
\
\
\
Applicatio](/manual-img/16/57037/w960_57037-1204.png "JEEP CHEROKEE 1988 Service Repair Manual TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS TABLE \
\
\
\
\
\
Applicatio")
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS TABLE \
\
\
\
\
\
Application Ft. Lbs. (N.m)
Companion Flange Nut
Chrysler Corp. ....................... 130-200 (176-271)
General Motors ................................ 80 (108)
Jeep ......................................... 110 (149)
Detent Plug
General Motors ................................. 11 (15)
Chrysler Corp. & Jeep .......................... 15 (20)
Drain & Fill Plug .......................... 30-40 (41-54)
Extension Housing Bolt ..................... 20-25 (27-34)
Front Bearing Retainer Bolt
Chrysler Corp. & Jeep .......................... 16 (22)
General Motors ................................. 14 (19)
Front Case-to-Rear Case Bolt
Chrysler Corp.
Flange Head Bolt ........................ 35-45 (47-61)
All Other Bolts ........................ 20-25 (27-34)
General Motors ................................. 23 (31)
Jeep ..................................... 20-25 (27-34)
Range Lever Nut ............................ 15-20 (20-27)
Rear Bearing Retainer Bolt ................. 20-25 (27-34)
Rear Crossmember ................................. 30 (41)
Shift Lever Lock Bolt ............................ 10 (14)
Speed Sensor Bolt ................................ 23 (31)
Transfer Case-to-Transmission Nut ................ 26 (35)
Vacuum Switch
Chrysler Corp. ........................... 15-25 (20-34)
General Motors ................................. 17 (23)
Jeep ..................................... 20-25 (27-34)
INCH Lbs.
Control Cable Lock Nut ............................ 18 (2)
\
\
\
\
\
\
VACUUM DIAGRAMS
For vacuum diagrams, refer to appropriate VACUUM DIAGRAMS
article in the ENGINE PERFORMANCE section.
Page 1247 of 1378
Low fuel pressure Test pressure regul-
ator and fuel pump,
check for restricted
lines and filters
No distributor reference Repair ignition
pulses system as necessary
Open coolant temperature Test sensor and
sensor circuit wiring
Shorted W.O.T. switch in Disconnect W.O.T.
T.P.S. switch, engine
should start
Defective ECM Replace ECM
Fuel tank residual pressure Test for fuel
valve leaks pressure drop after
shut down
\
\
\
\
\
\
\
Hard Starting Disconnected hot air tube Reconnect tube and
to air cleaner test control valve
Defective Idle Air Control Test valve operation
(IAC) valve and circuit
Shorted, open or misadjusted Test and adjust or
T.P.S. replace T.P.S.
EGR valve open Test EGR valve and
control circuit
Poor Oxygen sensor signal Test for shorted or
circuit
Incorrect mixture from PCV Test PCV for flow,
system check sealing of oil
filter cap
\
\
\
\
\
\
\
Poor High Speed Low fuel pump volume Faulty pump or
Operation restricted fuel
lines or filters
Poor MAP sensor signal Test MAP sensor,
vacuum hose and
wiring
Poor Oxygen sensor signal Test for shorted or
open sensor or
circuit
Open coolant temperature Test sensor and
sensor circuit wiring
Faulty ignition operation Check wires for
cracks or poor con-
nections, test
secondary voltage
with oscilloscope
Contaminated fuel Test fuel for water
Page 1248 of 1378
or alcohol
Intermittent ECM ground Test ECM ground
connection for
resistance
Restricted air cleaner Replace air cleaner
Restricted exhaust system Test for exhaust
manifold back
pressure
Poor MAF sensor signal Check leakage
between sensor and
manifold
Poor VSS signal If tester for ALCL
hook-up is available
check that VSS
reading matches
speedometer
\
\
\
\
\
\
\
Ping or Knock on Poor Knock sensor signal Test for shorted or
Acceleration open sensor or
circuit
Poor Baro sensor signal Test for shorted or
open sensor or
circuit
Improper ignition timing See VEHICLE EMISSION
CONTROL LABEL (where
applicable)
Check for engine Low coolant, loose
overheating problems belts or electric
cooling fan
inoperative
\
\
\
\
\
\
\
NOTE: For additional electronic fuel injection trouble shooting
information, see the appropriate article in the ENGINE
PERFORMANCE section (not all vehicles have Computer Engine
Control articles). Information is provided there for
diagnosing fuel system problems on vehicles with electronic
fuel injection.
IGNITION SYSTEM TROUBLE SHOOTING
NOTE: This is GENERAL information. This article is not intended
to be specific to any unique situation or individual vehicle
configuration. The purpose of this Trouble Shooting
information is to provide a list of common causes to
problem symptoms. For model-specific Trouble Shooting,
refer to SUBJECT, DIAGNOSTIC, or TESTING articles available
in the section(s) you are accessing.
Ignition Secondary Trouble Shooting Chart
\
\
\
\
\
\
START: Visually inspect Spark Plug Wires, Coil Wires,
Plug Wire Boots, Rotor, and Distributor Cap for
signs of damage.