1988 JEEP CHEROKEE power steering fluid

tires radio controls remote start wiring diagram washer fluid suspension

Page 967 of 1378

JEEP CHEROKEE 1988 Service Repair Manual Engine Coolant ........... Alugard 340-2 & Water (50/50 Mixture)

Engine Oil (
1)

Gasoline Engine

Engine Coolant ........... Alugard 340-2 & Water (50/50 Mixture)

Engine Oil (
1)

Gasoline Engine

Temperature Range

Above 30
F (-1
C) ........ SAE 20W-40 Or 20W-50 API SH/CD

Above 0
F (-18
C) ......... SAE 10W-30 Or 10W-40 API SH/CD

Less Than 60
F (16
C) ............... SAE 5W-30 API SH/CD

Drive Axles ................................ SAE 75W-90 API GL-5

Drive Axles (Trac-Lok) (
2) ................ SAE 80W-140 API GL-5

Drive Axles (Trailer Towing) .............. SAE 80W-140 API GL-5

Hydraulic Clutch ............... DOT 3 (SAE J-1703F) Brake Fluid

Manual Transmission ........................ SAE 75W-90 API GL-5

Parking Brake Cable Guides ................. NLGI Grade 2, GC-LB

Door & Hood Hinges ............................ Light Engine Oil

Manual Steering Box ............... Multi-Purpose NLGI Grade 2EP

Power Steering Pump ....................... Power Steering Fluid

Transfer Case ................................... Dexron-IIE ATF

Brake Caliper Bushings ........ GE 661 or DOW 111 Silicone Grease

Caliper Slide Pins ........... GE 661 or DOW 111 Silicone Grease

Wheel Bearings .................. Multi-Purpose NLGI Grade GC-LB

Drive Shaft U-Joints .............. Multi-Purpose NLGI Grade 2EP

Steering Linkage (
4)( 5) .................... NLGI Grade 2, GC-LB

Ball Joints (
4)( 6) ......................... NLGI Grade 2, GC-LB

Weatherstrip .......................... Silicone Spray Lubricant

Wheel Lug Nut Torque ...................... 95 ft. lbs. (129 N.m)

(
1) - SAE 10W-30 SH/CD is preferred.

(
2) - Add 4 ozs. (118 ml) of Limited-Slip differential lubricant

additive when changing fluid.

(
3) - For vehicles operating under heavy-duty towing conditions,

use SAE 75W-140 Synthetic lube.

NOTE: Before using SAE 75W-140 Synthetic the old fluid must

be DRAINED and FLUSHED with clean mineral based axle

lubricant. Then refill with new synthetic lube.

(
4) - Use low pressure grease gun to prevent seal damage.

(
5) - Fill until lubricant squeezes out from the base of seals.

(
6) - Fill ball joint until seal starts to swell.

\
\
\
\
\
\
\

Fluid Capacities

\
\
\
\
\
\
\

Application ( 1) Quantity

Automatic Transmission

1984-86 (904 HD)

Fluid Change ............................... 4.0 Qts. (3.8L)

Overhaul (Dry Fill) ........................ 8.0 Qts. (7.6L) \

1987-88

Fluid Change ............................... 4.0 Qts. (3.8L)

Overhaul (Dry Fill) ........................ 8.5 Qts. (8.0L) \

Cooling System (
2)

4-Cylinder .................................. 10.0 Qts. (9.5L)

6-Cylinder ................................. 12.0 Qts. (11.4L)

Engine Oil

4-Cylinder ................................... 4.0 Qts. (3.8L)

6-Cylinder ................................... 6.0 Qts. (5.7L)

Fuel Tank

Standard .................................. 13.5 Gals. (51.1L)

Optional .................................... 20 Gals. (75.7L)

Manual Transmission (
3)

AX4 (AISIN) .................................. 7.4 Pts. (3.5L) \

T4 (Borg-Warner) ............................. 3.9 Pts. (1.8L) \

AX5 (AISIN) .................................. 7.0 Pts. (3.3L) \

T5 (Borg-Warner) ............................. 4.5 Pts. (2.1L) \

Page 969 of 1378

$JEEP CHEROKEE 1988 Service Repair Manual Lube Front Axle Drive Joint and Pivot Bearings (4WD) \b\ \ \ \ \ \$

Lube Front Axle Drive Joint and Pivot Bearings (4WD)

\b\
\
\
\
\
\
\

Suspension Bushings, Springs, Arms & Rear Jounce Bumpers

\b\
\
\
\
\
\
\

Parking Brake System

\b\
\
\
\
\
\
\

Lubricate Body Components

\b\
\
\
\
\
\
\

Inspect Shocks for Leakage

\b\
\
\
\
\
\
\

Inspect Tire Wear Pattern

\b\
\
\
\
\
\
\

Rotate Tires and Adjust Air Pressure (Including Spare)

\
\
\
\
\
\
\

Replace

\
\
\
\
\
\
\

Engine Oil

\b\
\
\
\
\
\
\

Oil Filter

\b\
\
\
\
\
\
\

Spark Plugs

\b\
\
\
\
\
\
\

Air Filter Element

\b\
\
\
\
\
\
\

PCV Filter

\b\
\
\
\
\
\
\

Fuel Filter

\
\
\
\
\
\
\

Lubrication Specifications

\
\
\
\
\
\
\

Application Specification

Automatic Transmission .......................... Dexron-IIE ATF

Brake Master Cylinder .......... DOT 3 (SAE J-1703F) Brake Fluid

Engine Coolant ........... Alugard 340-2 & Water (50/50 Mixture)

Engine Oil (
1)

Gasoline Engine

Temperature Range

Above 30
F (-1
C) ........ SAE 20W-40 Or 20W-50 API SH/CD

Above 0
F (-18
C) ......... SAE 10W-30 Or 10W-40 API SH/CD

Less Than 60
F (16
C) ............... SAE 5W-30 API SH/CD

Drive Axles ................................ SAE 75W-90 API GL-5

Drive Axles (Trac-Lok) (
2) ................ SAE 80W-140 API GL-5

Drive Axles (Trailer Towing) .............. SAE 80W-140 API GL-5

Hydraulic Clutch ............... DOT 3 (SAE J-1703F) Brake Fluid

Manual Transmission ........................ SAE 75W-90 API GL-5

Parking Brake Cable Guides ................. NLGI Grade 2, GC-LB

Door & Hood Hinges ............................ Light Engine Oil

Manual Steering Box ............... Multi-Purpose NLGI Grade 2EP

Power Steering Pump ....................... Power Steering Fluid

Transfer Case ................................... Dexron-IIE ATF

Brake Caliper Bushings ........ GE 661 or DOW 111 Silicone Grease

Caliper Slide Pins ........... GE 661 or DOW 111 Silicone Grease

Wheel Bearings .................. Multi-Purpose NLGI Grade GC-LB

Drive Shaft U-Joints .............. Multi-Purpose NLGI Grade 2EP

Steering Linkage (
4)( 5) .................... NLGI Grade 2, GC-LB

Ball Joints (
4)( 6) ......................... NLGI Grade 2, GC-LB

Weatherstrip .......................... Silicone Spray Lubricant

Wheel Lug Nut Torque ...................... 95 ft. lbs. (129 N.m)

(
1) - SAE 10W-30 SH/CD is preferred.

(
2) - Add 4 ozs. (118 ml) of Limited-Slip differential lubricant

additive when changing fluid.

Page 972 of 1378

JEEP CHEROKEE 1988 Service Repair Manual Brake Master Cylinder .......... DOT 3 (SAE J-1703F) Brake Fluid

Engine Coolant ........... Alugard 340-2 & Water (50/50 Mixture)

Engine Oil (
1)

Brake Master Cylinder .......... DOT 3 (SAE J-1703F) Brake Fluid

Engine Coolant ........... Alugard 340-2 & Water (50/50 Mixture)

Engine Oil (
1)

Gasoline Engine

Temperature Range

Above 30
F (-1
C) ........ SAE 20W-40 Or 20W-50 API SH/CD

Above 0
F (-18
C) ......... SAE 10W-30 Or 10W-40 API SH/CD

Less Than 60
F (16
C) ............... SAE 5W-30 API SH/CD

Drive Axles ................................ SAE 75W-90 API GL-5

Drive Axles (Trac-Lok) (
2) ................ SAE 80W-140 API GL-5

Drive Axles (Trailer Towing) .............. SAE 80W-140 API GL-5

Hydraulic Clutch ............... DOT 3 (SAE J-1703F) Brake Fluid

Manual Transmission ........................ SAE 75W-90 API GL-5

Parking Brake Cable Guides ................. NLGI Grade 2, GC-LB

Door & Hood Hinges ............................ Light Engine Oil

Manual Steering Box ............... Multi-Purpose NLGI Grade 2EP

Power Steering Pump ....................... Power Steering Fluid

Transfer Case ................................... Dexron-IIE ATF

Brake Caliper Bushings ........ GE 661 or DOW 111 Silicone Grease

Caliper Slide Pins ........... GE 661 or DOW 111 Silicone Grease

Wheel Bearings .................. Multi-Purpose NLGI Grade GC-LB

Drive Shaft U-Joints .............. Multi-Purpose NLGI Grade 2EP

Steering Linkage (
4)( 5) .................... NLGI Grade 2, GC-LB

Ball Joints (
4)( 6) ......................... NLGI Grade 2, GC-LB

Weatherstrip .......................... Silicone Spray Lubricant

Wheel Lug Nut Torque ...................... 95 ft. lbs. (129 N.m)

(
1) - SAE 10W-30 SH/CD is preferred.

(
2) - Add 4 ozs. (118 ml) of Limited-Slip differential lubricant

additive when changing fluid.

(
3) - For vehicles operating under heavy-duty towing conditions,

use SAE 75W-140 Synthetic lube.

NOTE: Before using SAE 75W-140 Synthetic the old fluid must

be DRAINED and FLUSHED with clean mineral based axle

lubricant. Then refill with new synthetic lube.

(
4) - Use low pressure grease gun to prevent seal damage.

(
5) - Fill until lubricant squeezes out from the base of seals.

(
6) - Fill ball joint until seal starts to swell.

\
\
\
\
\
\
\

Fluid Capacities

\
\
\
\
\
\
\

Application ( 1) Quantity

Automatic Transmission

1984-86 (904 HD)

Fluid Change ............................... 4.0 Qts. (3.8L)

Overhaul (Dry Fill) ........................ 8.0 Qts. (7.6L) \

1987-88

Fluid Change ............................... 4.0 Qts. (3.8L)

Overhaul (Dry Fill) ........................ 8.5 Qts. (8.0L) \

Cooling System (
2)

4-Cylinder .................................. 10.0 Qts. (9.5L)

6-Cylinder ................................. 12.0 Qts. (11.4L)

Engine Oil

4-Cylinder ................................... 4.0 Qts. (3.8L)

6-Cylinder ................................... 6.0 Qts. (5.7L)

Fuel Tank

Standard .................................. 13.5 Gals. (51.1L)

Optional .................................... 20 Gals. (75.7L)

Manual Transmission (
3)

AX4 (AISIN) .................................. 7.4 Pts. (3.5L) \

T4 (Borg-Warner) ............................. 3.9 Pts. (1.8L) \

AX5 (AISIN) .................................. 7.0 Pts. (3.3L) \

Page 975 of 1378

JEEP CHEROKEE 1988 Service Repair Manual Drive Axles (Trac-Lok) (2) ................ SAE 80W-140 API GL-5

Drive Axles (Trailer Towing) .............. SAE 80W-140 API GL-5

Hydraulic Clutch ............... DOT 3 (SAE J-1703F)

Drive Axles (Trac-Lok) (2) ................ SAE 80W-140 API GL-5

Drive Axles (Trailer Towing) .............. SAE 80W-140 API GL-5

Hydraulic Clutch ............... DOT 3 (SAE J-1703F) Brake Fluid

Manual Transmission ........................ SAE 75W-90 API GL-5

Parking Brake Cable Guides ................. NLGI Grade 2, GC-LB

Door & Hood Hinges ............................ Light Engine Oil

Manual Steering Box ............... Multi-Purpose NLGI Grade 2EP

Power Steering Pump ....................... Power Steering Fluid

Transfer Case ................................... Dexron-IIE ATF

Brake Caliper Bushings ........ GE 661 or DOW 111 Silicone Grease

Caliper Slide Pins ........... GE 661 or DOW 111 Silicone Grease

Wheel Bearings .................. Multi-Purpose NLGI Grade GC-LB

Drive Shaft U-Joints .............. Multi-Purpose NLGI Grade 2EP

Steering Linkage (
4)( 5) .................... NLGI Grade 2, GC-LB

Ball Joints (
4)( 6) ......................... NLGI Grade 2, GC-LB

Weatherstrip .......................... Silicone Spray Lubricant

Wheel Lug Nut Torque ...................... 95 ft. lbs. (129 N.m)

(
1) - SAE 10W-30 SH/CD is preferred.

(
2) - Add 4 ozs. (118 ml) of Limited-Slip differential lubricant

additive when changing fluid.

(
3) - For vehicles operating under heavy-duty towing conditions,

use SAE 75W-140 Synthetic lube.

NOTE: Before using SAE 75W-140 Synthetic the old fluid must

be DRAINED and FLUSHED with clean mineral based axle

lubricant. Then refill with new synthetic lube.

(
4) - Use low pressure grease gun to prevent seal damage.

(
5) - Fill until lubricant squeezes out from the base of seals.

(
6) - Fill ball joint until seal starts to swell.

\
\
\
\
\
\
\

Fluid Capacities

\
\
\
\
\
\
\

Application ( 1) Quantity

Automatic Transmission

1984-86 (904 HD)

Fluid Change ............................... 4.0 Qts. (3.8L)

Overhaul (Dry Fill) ........................ 8.0 Qts. (7.6L) \

1987-88

Fluid Change ............................... 4.0 Qts. (3.8L)

Overhaul (Dry Fill) ........................ 8.5 Qts. (8.0L) \

Cooling System (
2)

4-Cylinder .................................. 10.0 Qts. (9.5L)

6-Cylinder ................................. 12.0 Qts. (11.4L)

Engine Oil

4-Cylinder ................................... 4.0 Qts. (3.8L)

6-Cylinder ................................... 6.0 Qts. (5.7L)

Fuel Tank

Standard .................................. 13.5 Gals. (51.1L)

Optional .................................... 20 Gals. (75.7L)

Manual Transmission (
3)

AX4 (AISIN) .................................. 7.4 Pts. (3.5L) \

T4 (Borg-Warner) ............................. 3.9 Pts. (1.8L) \

AX5 (AISIN) .................................. 7.0 Pts. (3.3L) \

T5 (Borg-Warner) ............................. 4.5 Pts. (2.1L) \

Transfer Case

1985-86

Selec-Trac (229 Full-Time) ................. 6.0 Pts. (2.8L) \

Command-Trac (Part-Time 207) ............... 4.5 Pts. (2.1L) \

1987

Selec-Trac ................................. 2.5 Pts. (1.2L)

Command-Trac ............................... 2.2 Pts. (1.0L)

1988

Page 977 of 1378

$JEEP CHEROKEE 1988 Service Repair Manual Flush and Fill Engine Coolant, if not done in last 36 months \ \ \ \ \ \$

Flush and Fill Engine Coolant, if not done in last 36 months

\
\
\
\
\
\
\

Lubrication Specifications

\
\
\
\
\
\
\

Application Specification

Automatic Transmission .......................... Dexron-IIE ATF

Brake Master Cylinder .......... DOT 3 (SAE J-1703F) Brake Fluid

Engine Coolant ........... Alugard 340-2 & Water (50/50 Mixture)

Engine Oil (
1)

Gasoline Engine

Temperature Range

Above 30
F (-1
C) ........ SAE 20W-40 Or 20W-50 API SH/CD

Above 0
F (-18
C) ......... SAE 10W-30 Or 10W-40 API SH/CD

Less Than 60
F (16
C) ............... SAE 5W-30 API SH/CD

Drive Axles ................................ SAE 75W-90 API GL-5

Drive Axles (Trac-Lok) (
2) ................ SAE 80W-140 API GL-5

Drive Axles (Trailer Towing) .............. SAE 80W-140 API GL-5

Hydraulic Clutch ............... DOT 3 (SAE J-1703F) Brake Fluid

Manual Transmission ........................ SAE 75W-90 API GL-5

Parking Brake Cable Guides ................. NLGI Grade 2, GC-LB

Door & Hood Hinges ............................ Light Engine Oil

Manual Steering Box ............... Multi-Purpose NLGI Grade 2EP

Power Steering Pump ....................... Power Steering Fluid

Transfer Case ................................... Dexron-IIE ATF

Brake Caliper Bushings ........ GE 661 or DOW 111 Silicone Grease

Caliper Slide Pins ........... GE 661 or DOW 111 Silicone Grease

Wheel Bearings .................. Multi-Purpose NLGI Grade GC-LB

Drive Shaft U-Joints .............. Multi-Purpose NLGI Grade 2EP

Steering Linkage (
4)( 5) .................... NLGI Grade 2, GC-LB

Ball Joints (
4)( 6) ......................... NLGI Grade 2, GC-LB

Weatherstrip .......................... Silicone Spray Lubricant

Wheel Lug Nut Torque ...................... 95 ft. lbs. (129 N.m)

(
1) - SAE 10W-30 SH/CD is preferred.

(
2) - Add 4 ozs. (118 ml) of Limited-Slip differential lubricant

additive when changing fluid.

(
3) - For vehicles operating under heavy-duty towing conditions,

use SAE 75W-140 Synthetic lube.

NOTE: Before using SAE 75W-140 Synthetic the old fluid must

be DRAINED and FLUSHED with clean mineral based axle

lubricant. Then refill with new synthetic lube.

(
4) - Use low pressure grease gun to prevent seal damage.

(
5) - Fill until lubricant squeezes out from the base of seals.

(
6) - Fill ball joint until seal starts to swell.

\
\
\
\
\
\
\

Fluid Capacities

\
\
\
\
\
\
\

Application ( 1) Quantity

Automatic Transmission

1984-86 (904 HD)

Fluid Change ............................... 4.0 Qts. (3.8L)

Overhaul (Dry Fill) ........................ 8.0 Qts. (7.6L) \

1987-88

Fluid Change ............................... 4.0 Qts. (3.8L)

Overhaul (Dry Fill) ........................ 8.5 Qts. (8.0L) \

Cooling System (
2)

4-Cylinder .................................. 10.0 Qts. (9.5L)

6-Cylinder ................................. 12.0 Qts. (11.4L)

Engine Oil

4-Cylinder ................................... 4.0 Qts. (3.8L)

6-Cylinder ................................... 6.0 Qts. (5.7L)

Page 980 of 1378

$JEEP CHEROKEE 1988 Service Repair Manual \b\ \ \ \ \ \ \ Fuel Filter$

\b\
\
\
\
\
\
\

Fuel Filter

\b\
\
\
\
\
\
\

Emission System Vacuum Hoses

\b\
\
\
\
\
\
\

Ignition Wires

\b\
\
\
\
\
\
\

Distributor Cap & Rotor

\b\
\
\
\
\
\
\

Battery

\
\
\
\
\
\
\

(
1) - Replacement is recommended by Chrysler at this time, but it

is not required to maintain the warranty on the PCV valve.

(
2) - Check and replace as needed.

\
\
\
\
\
\
\

Lubrication Specifications

\
\
\
\
\
\
\

Application Specification

Automatic Transmission .......................... Dexron-IIE ATF

Brake Master Cylinder .......... DOT 3 (SAE J-1703F) Brake Fluid

Engine Coolant ........... Alugard 340-2 & Water (50/50 Mixture)

Engine Oil (
1)

Gasoline Engine

Temperature Range

Above 30
F (-1
C) ........ SAE 20W-40 Or 20W-50 API SH/CD

Above 0
F (-18
C) ......... SAE 10W-30 Or 10W-40 API SH/CD

Less Than 60
F (16
C) ............... SAE 5W-30 API SH/CD

Drive Axles ................................ SAE 75W-90 API GL-5

Drive Axles (Trac-Lok) (
2) ................ SAE 80W-140 API GL-5

Drive Axles (Trailer Towing) .............. SAE 80W-140 API GL-5

Hydraulic Clutch ............... DOT 3 (SAE J-1703F) Brake Fluid

Manual Transmission ........................ SAE 75W-90 API GL-5

Parking Brake Cable Guides ................. NLGI Grade 2, GC-LB

Door & Hood Hinges ............................ Light Engine Oil

Manual Steering Box ............... Multi-Purpose NLGI Grade 2EP

Power Steering Pump ....................... Power Steering Fluid

Transfer Case ................................... Dexron-IIE ATF

Brake Caliper Bushings ........ GE 661 or DOW 111 Silicone Grease

Caliper Slide Pins ........... GE 661 or DOW 111 Silicone Grease

Wheel Bearings .................. Multi-Purpose NLGI Grade GC-LB

Drive Shaft U-Joints .............. Multi-Purpose NLGI Grade 2EP

Steering Linkage (
4)( 5) .................... NLGI Grade 2, GC-LB

Ball Joints (
4)( 6) ......................... NLGI Grade 2, GC-LB

Weatherstrip .......................... Silicone Spray Lubricant

Wheel Lug Nut Torque ...................... 95 ft. lbs. (129 N.m)

(
1) - SAE 10W-30 SH/CD is preferred.

(
2) - Add 4 ozs. (118 ml) of Limited-Slip differential lubricant

additive when changing fluid.

(
3) - For vehicles operating under heavy-duty towing conditions,

use SAE 75W-140 Synthetic lube.

NOTE: Before using SAE 75W-140 Synthetic the old fluid must

be DRAINED and FLUSHED with clean mineral based axle

lubricant. Then refill with new synthetic lube.

(
4) - Use low pressure grease gun to prevent seal damage.

(
5) - Fill until lubricant squeezes out from the base of seals.

(
6) - Fill ball joint until seal starts to swell.

\
\
\
\
\
\
\

Fluid Capacities

\
\
\
\
\
\
\

Application ( 1) Quantity

Page 983 of 1378

JEEP CHEROKEE 1988 Service Repair Manual Above 30
F (-1
C) ........ SAE 20W-40 Or 20W-50 API SH/CD

Above 0
F (-18
C) ......... SAE 10W-30 Or 10W-40 API SH/CD

Less Than 60
F (16
C) ............... SAE 5W-

Above 30
F (-1
C) ........ SAE 20W-40 Or 20W-50 API SH/CD

Above 0
F (-18
C) ......... SAE 10W-30 Or 10W-40 API SH/CD

Less Than 60
F (16
C) ............... SAE 5W-30 API SH/CD

Drive Axles ................................ SAE 75W-90 API GL-5

Drive Axles (Trac-Lok) (
2) ................ SAE 80W-140 API GL-5

Drive Axles (Trailer Towing) .............. SAE 80W-140 API GL-5

Hydraulic Clutch ............... DOT 3 (SAE J-1703F) Brake Fluid

Manual Transmission ........................ SAE 75W-90 API GL-5

Parking Brake Cable Guides ................. NLGI Grade 2, GC-LB

Door & Hood Hinges ............................ Light Engine Oil

Manual Steering Box ............... Multi-Purpose NLGI Grade 2EP

Power Steering Pump ....................... Power Steering Fluid

Transfer Case ................................... Dexron-IIE ATF

Brake Caliper Bushings ........ GE 661 or DOW 111 Silicone Grease

Caliper Slide Pins ........... GE 661 or DOW 111 Silicone Grease

Wheel Bearings .................. Multi-Purpose NLGI Grade GC-LB

Drive Shaft U-Joints .............. Multi-Purpose NLGI Grade 2EP

Steering Linkage (
4)( 5) .................... NLGI Grade 2, GC-LB

Ball Joints (
4)( 6) ......................... NLGI Grade 2, GC-LB

Weatherstrip .......................... Silicone Spray Lubricant

Wheel Lug Nut Torque ...................... 95 ft. lbs. (129 N.m)

(
1) - SAE 10W-30 SH/CD is preferred.

(
2) - Add 4 ozs. (118 ml) of Limited-Slip differential lubricant

additive when changing fluid.

(
3) - For vehicles operating under heavy-duty towing conditions,

use SAE 75W-140 Synthetic lube.

NOTE: Before using SAE 75W-140 Synthetic the old fluid must

be DRAINED and FLUSHED with clean mineral based axle

lubricant. Then refill with new synthetic lube.

(
4) - Use low pressure grease gun to prevent seal damage.

(
5) - Fill until lubricant squeezes out from the base of seals.

(
6) - Fill ball joint until seal starts to swell.

\
\
\
\
\
\
\

Fluid Capacities

\
\
\
\
\
\
\

Application ( 1) Quantity

Automatic Transmission

1984-86 (904 HD)

Fluid Change ............................... 4.0 Qts. (3.8L)

Overhaul (Dry Fill) ........................ 8.0 Qts. (7.6L) \

1987-88

Fluid Change ............................... 4.0 Qts. (3.8L)

Overhaul (Dry Fill) ........................ 8.5 Qts. (8.0L) \

Cooling System (
2)

4-Cylinder .................................. 10.0 Qts. (9.5L)

6-Cylinder ................................. 12.0 Qts. (11.4L)

Engine Oil

4-Cylinder ................................... 4.0 Qts. (3.8L)

6-Cylinder ................................... 6.0 Qts. (5.7L)

Fuel Tank

Standard .................................. 13.5 Gals. (51.1L)

Optional .................................... 20 Gals. (75.7L)

Manual Transmission (
3)

AX4 (AISIN) .................................. 7.4 Pts. (3.5L) \

T4 (Borg-Warner) ............................. 3.9 Pts. (1.8L) \

AX5 (AISIN) .................................. 7.0 Pts. (3.3L) \

T5 (Borg-Warner) ............................. 4.5 Pts. (2.1L) \

Transfer Case

1985-86

Selec-Trac (229 Full-Time) ................. 6.0 Pts. (2.8L) \

Command-Trac (Part-Time 207) ............... 4.5 Pts. (2.1L) \

Page 985 of 1378

$JEEP CHEROKEE 1988 Service Repair Manual Check Drive Shaft Seals \b\ \ \ \ \ \$

Check Drive Shaft Seals

\b\
\
\
\
\
\
\

Lubricate Ball Joints, Steering Linkage & Suspension

\b\
\
\
\
\
\
\

Lube Drive Shaft U-Joints and Slip Splines

\b\
\
\
\
\
\
\

Lube Front Axle Drive Joint and Pivot Bearings (4WD)

\b\
\
\
\
\
\
\

Lubricate Weatherstripping with Silicone

\b\
\
\
\
\
\
\

Lubricate Door Hinges

\b\
\
\
\
\
\
\

Lubricate Door Locks

\b\
\
\
\
\
\
\

Check Body Drain Holes

\b\
\
\
\
\
\
\

Rotate Tires and Adjust Air Pressure

\
\
\
\
\
\
\

Replace

\
\
\
\
\
\
\

Engine Oil

\b\
\
\
\
\
\
\

Oil Filter

\b\
\
\
\
\
\
\

Manual Transmission Fluid

\b\
\
\
\
\
\
\

Automatic Transmission Fluid, Filter and Adjust Bands

\b\
\
\
\
\
\
\

Transfer Case Fluid

\b\
\
\
\
\
\
\

Flush and Fill Engine Coolant, if not done in last 24 months

\
\
\
\
\
\
\

Lubrication Specifications

\
\
\
\
\
\
\

Application Specification

Automatic Transmission .......................... Dexron-IIE ATF

Brake Master Cylinder .......... DOT 3 (SAE J-1703F) Brake Fluid

Engine Coolant ........... Alugard 340-2 & Water (50/50 Mixture)

Engine Oil (
1)

Gasoline Engine

Temperature Range

Above 30
F (-1
C) ........ SAE 20W-40 Or 20W-50 API SH/CD

Above 0
F (-18
C) ......... SAE 10W-30 Or 10W-40 API SH/CD

Less Than 60
F (16
C) ............... SAE 5W-30 API SH/CD

Drive Axles ................................ SAE 75W-90 API GL-5

Drive Axles (Trac-Lok) (
2) ................ SAE 80W-140 API GL-5

Drive Axles (Trailer Towing) .............. SAE 80W-140 API GL-5

Hydraulic Clutch ............... DOT 3 (SAE J-1703F) Brake Fluid

Manual Transmission ........................ SAE 75W-90 API GL-5

Parking Brake Cable Guides ................. NLGI Grade 2, GC-LB

Door & Hood Hinges ............................ Light Engine Oil

Manual Steering Box ............... Multi-Purpose NLGI Grade 2EP

Power Steering Pump ....................... Power Steering Fluid

Transfer Case ................................... Dexron-IIE ATF

Brake Caliper Bushings ........ GE 661 or DOW 111 Silicone Grease

Caliper Slide Pins ........... GE 661 or DOW 111 Silicone Grease

Wheel Bearings .................. Multi-Purpose NLGI Grade GC-LB

Drive Shaft U-Joints .............. Multi-Purpose NLGI Grade 2EP

Steering Linkage (
4)( 5) .................... NLGI Grade 2, GC-LB

Ball Joints (
4)( 6) ......................... NLGI Grade 2, GC-LB

Weatherstrip .......................... Silicone Spray Lubricant

Wheel Lug Nut Torque ...................... 95 ft. lbs. (129 N.m)

Load next 8 pages

Page: < prev 1-8 9-16 17-24 25-32 33-40 40 next >

diagnostic menu service indicator towing capacity wiper fluid rear entertainment clock setting