1988 JEEP CHEROKEE check engine light

should be on. Light No. 1 should be off. Light No. 4 will dim when
servo moves throttle to wide open position, if engine is running.
2) If light No. 2 is off, check speed sensor terminal
connections to control module through Gray and Drk. Blue wires. Check
terminals No. 2, 3, 5 and 7 (Gray, Drk. Blue and Lt. Green wires) for
ground.
3) If light No. 3 is off, check brake light switch, and check
all Brown, Lt. Blue and Lt. Green wire connections. If light No. 4 is
off, check terminals No. 2 and 11 at control module connector. Check
continuity of throttle position feedback rheostat of servo.
4) If light No. 5 is off, check for bad connection at White
(6) and Orange (12) wire terminals. If necessary, replace defective
servo.
5) If all lights are off after moving control switch to "R/A"
position, check for blown fuse or fuses, and check Red, Pink, Brown or
White wires for shorts. If necessary replace defective servo.
Grand Wagoneer
1) With ignition and control switches in "ON" position, slide
control switch to "R/A" position. All test lights should be on. Light
No. 4 will dim when servo moves throttle to wide open position, if
engine is running.
2) If light No. 1 is off, check for blown fuse in brake light
switch to control switch circuit. Check Red, Brown and Green wires at
control switch for continuity to switch.
3) If light No. 2 is off, check Gray and Drk. Blue wire at
speed sensor connector for continuity to control module connector.
4) If light No. 3 is off, check brake light switch
adjustment. If light No. 4 is off, check for defective connection at
terminals No. 2 and 11 on control module connector. Check operation of
throttle position feedback rheostat on servo.
5) If light No. 5 is off, check for defective connections at
terminals No. 4 and 12 on control module connector. If necessary,
replace defective servo. If light No. 6 is off, check for defective
connection at terminals No. 6 and 12 on control module connector. If
necessary, replace defective servo.
6) If all lights are off after moving control switch to "R/A"
position, check for blown fuse. Check for short circuits in Red, Pink
and Brown wire circuits at control switch. If necessary, replace
defective servo.
SPEED SENSOR TEST
1) Disconnect wire harness connector at speed sensor. Connect
a voltmeter (set on low AC scale) to terminals from speed sensor.
2) Raise front and rear wheels of vehicle off ground and
support vehicle with safety stands. Run engine (wheels spinning
freely) at 30 MPH and note voltage.
3) Voltage should be approximately .9 volts. Increases of .1
volts per each 10 MPH increase in speed should also be noticed. Turn
off engine and stop wheels. Lower vehicle. Connect speed sensor wire
harness.
SERVO TEST
1) With ignition switch in "OFF" position, disconnect servo
wire harness connector. Remove vacuum hose from brake pedal vent valve
nipple on servo. Disconnect servo cable from throttle linkage at
carburetor.
2) Connect an ohmmeter between ground and Red. Ground and
Orange. And Ground and White wire terminals of servo wire harness
connector. See Fig. 5. Observe ohmmeter during each test. An infinite
(open circuit) resistance should be indicated for each wire terminal.

\003
DO OR L O CKS - P O W ER

1988 J e ep C hero ke e
1988 Power Door Locks
JEEP
DESCRIPTION
Jeep vehicles with power door locks use a motor-actuated lock
system, controlled by rocker switches. Operation of switch assembly
controls the actuator motor.
Power door locks are protected by a 30-amp circuit breaker
located in the fuse block. Power door locks will not operate from
outside the vehicle.
TESTING
SWITCH
Using ohmmeter, test switches for continuity. Connect
ohmmeter across terminals as shown. See Fig. 1. Continuity should
exist between terminals in all positions.
Fig. 1: Checking Switch Continuity
Courtesy of Chrysler Motors.
ACTUATOR MOTOR
Connect ammeter to actuator motor terminals. Operate door
switch and note reading. Current draw should not exceed 8 amps at room
temperature. Actuator should complete full travel within one second.
Replace actuator motor if not within specification.
CIRCUIT BREAKER
1) Disconnect harness connector from fuse block. Using test
light, check fuse block harness connection for voltage. If there is no
battery voltage at connection, check for burnt fusible link in engine
compartment.
2) Check circuit breaker continuity if voltage exists. Using
ohmmeter, test circuit breaker for continuity. Replace circuit breaker
if no continuity exists.
3) If circuit breaker tests okay, check for battery voltage
at circuit breaker connection of fuse block with wiring harness
installed. If voltage exists at wiring harness but not at circuit
breaker connection, check fuse block for damage.
REMOVAL & INSTALLATION

EARLY FUEL EVAPORATION (EFE)
The EFE valve is actuated by either a vacuum actuator or a
bimetal spring (heat-riser type). The EFE valve is closed when engine
is cold. The closed valve restricts exhaust gas flow from the exhaust
manifold. This forces part of the exhaust gas to flow up through a
passage below the carburetor. As the exhaust gas quickly warms the
intake mixture, distribution is improved. This results in better cold
engine driveability, shorter choke periods and lower emissions.
Ensure EFE valve in exhaust manifold is not frozen or rusted
in a fixed position. On vacuum-actuated EFE system, check EFE thermal
vacuum valve and check valve(s). Also check for proper vacuum hose
routing. See Fig. 15.
Fig. 15: Typical Vacuum-Actuated EFE System
Courtesy of General Motors Corp.
EMISSION MAINTENANCE REMINDER LIGHT (EMR) (IF EQUIPPED)

If equipped, the EMR light (some models may use a reminder
flag) reminds vehicle operator that an emission system maintenance is
required. This indicator is activated after a predetermined
time/mileage.
When performing a smog check inspection, ensure EMR indicator
is not activated. On models using an EMR light, light should glow when
ignition switch is turned to ON position and should turn off when
engine is running.
If an EMR flag is present or an EMR light stays on with
engine running, fail vehicle and service or replace applicable
emission-related components. To reset an EMR indicator, refer to
appropriate MAINTENANCE REMINDER LIGHTS in the MAINTENANCE section.
MALFUNCTION INDICATOR LIGHT (MIL)
The Malfunction Indicator Light (MIL) is used to alert
vehicle operator that the computerized engine control system has
detected a malfunction (when it stays on all the time with engine
running). On some models, the MIL may also be used to display trouble
codes.
As a bulb and system check, malfunction indicator light will
glow when ignition switch is turned to ON position and engine is not
running. When engine is started, light should go out.

\003
EN G IN E O VER HAU L P R O CED URES - G EN ER AL IN FO RM ATIO N

1988 J e ep C hero ke e
Engine Overhaul Procedures - General Information
ALL PISTON ENGINES
* PLEASE READ THIS FIRST *
Examples used in this article are general in nature and do
not necessarily relate to a specific engine or system. Illustrations
and procedures have been chosen to guide mechanic through engine
overhaul process. Descriptions of processes of cleaning, inspection,
assembly and machine shop practice are included.
Always refer to appropriate engine overhaul article in the
ENGINES section for complete overhaul procedures and specifications
for the vehicle being repaired.
ENGINE IDENTIFICATION
The engine may be identified from its Vehicle Identification
Number (VIN) stamped on a metal tab. Metal tab may be located in
different locations depending on manufacturer. Engine identification
number or serial number is located on cylinder block. Location varies
with manufacturer.
INSPECTION PROCEDURES
* PLEASE READ THIS FIRST *
NOTE: Always refer to appropriate engine overhaul article in the
ENGINES section for complete overhaul procedures and
specifications for the vehicle being repaired.
GENERAL
Engine components must be inspected to meet manufacturer's
specifications and tolerances during overhaul. Proper dimensions and
tolerances must be met to obtain proper performance and maximum engine
life.
Micrometers, depth gauges and dial indicator are used for
checking tolerances during engine overhaul. Magnaflux, Magnaglo, dye-
check, ultrasonic and x-ray inspection procedures are used for parts
inspection.
MAGNETIC PARTICLE INSPECTION
Magnaflux & Magnaglo
Magnaflux is an inspection technique used to locate material
flaws and stress cracks. The part in question is subjected to a strong
magnetic field. The entire part, or a localized area, can be
magnetized. The part is coated with either a wet or dry material that
contains fine magnetic particles.
Cracks which are outlined by the particles cause an
interruption in the magnetic field. The dry powder method of Magnaflux
can be used in normal light. A crack will appear as an obvious bright
line.
Fluorescent liquid is used in conjunction with a blacklight
in a second Magnaflux system called Magnaglo. This type of inspection
demands a darkened room. The crack will appear as a glowing line in
this process. Both systems require complete demagnetizing upon

completion of the inspection. Magnetic particle inspection applies to
ferrous materials only.
PENETRANT INSPECTION
Zyglo
The Zyglo process coats the material with a fluorescent dye
penetrant. The part is often warmed to expand cracks that will be
penetrated by the dye. When the coated part is subjected to inspection
with a blacklight, a crack will glow brightly. Developing solution
is often used to enhance results. Parts made of any material, such as
aluminum cylinder heads or plastics, may be tested using this process.
Dye Check
Penetrating dye is sprayed on the previously cleaned
component. Dye is left on component for 5-45 minutes, depending upon
material density. Component is then wiped clean and sprayed with a
developing solution. Surface cracks will show up as a bright line.
ULTRASONIC INSPECTION
If an expensive part is suspected of internal cracking,
Ultrasonic testing is used. Sound waves are used for component
inspection.
X-RAY INSPECTION
This form of inspection is used on highly stressed
components. X-ray inspection maybe used to detect internal and
external flaws in any material.
PRESSURE TESTING
Cylinder heads can be tested for cracks using a pressure
tester. Pressure testing is performed by plugging all but one of the
holes in the head and injecting air or water into the open passage.
Leaks are indicated by the appearance of wet or damp areas when using
water. When air is used, it is necessary to spray the head surface
with a soap solution. Bubbles will indicate a leak. Cylinder head may
also be submerged in water heated to specified temperature to check
for cracks created during heat expansion.
CLEANING PROCEDURES
* PLEASE READ THIS FIRST *
NOTE: Always refer to appropriate engine overhaul article in the
ENGINES section for complete overhaul procedures and
specifications for the vehicle being repaired.
GENERAL
All components of an engine do not have the same cleaning
requirements. Physical methods include bead blasting and manual
removal. Chemical methods include solvent blast, solvent tank, hot
tank, cold tank and steam cleaning of components.
BEAD BLASTING
Manual removal of deposits may be required prior to bead
blasting, followed by some other cleaning method. Carbon, paint and

NOTE: Always refer to appropriate engine overhaul article in the
ENGINES section for complete overhaul procedures and
specifications for the vehicle being repaired.
REMOVAL
Remove intake and exhaust manifolds and valve cover. Cylinder
head and camshaft carrier bolts (if equipped), should be removed only
when the engine is cold. On many aluminum cylinder heads, removal
while hot will cause cylinder head warpage. Mark rocker arm or
overhead cam components for location.
Remove rocker arm components or overhead cam components.
Components must be installed in original location. Individual design
rocker arms may utilize shafts, ball-type pedestal mounts or no rocker
arms. For all design types, wire components together and identify
according to the corresponding valve. Remove cylinder head bolts.
Note length and location. Some applications require cylinder head
bolts be removed in proper sequence to prevent cylinder head damage.
See Fig. 1 . Remove cylinder head.
Fig. 1: Typical Cylinder Head Tightening or Loosening Sequence
This Graphic For General Information Only
INSTALLATION
Ensure all surfaces and head bolts are clean. Check that head
bolt holes of cylinder block are clean and dry to prevent block damage
when bolts are tightened. Clean threads with tap to ensure accurate
bolt torque.
Install head gasket on cylinder block. Some manufacturer's
may recommend sealant be applied to head gasket prior to installation.
Note that all holes are aligned. Some gasket applications may be
marked so certain area faces upward. Install cylinder head using care
not to damage head gasket. Ensure cylinder head is fully seated on
cylinder block.
Some applications require head bolts be coated with sealant
prior to installation. This is done if head bolts are exposed to water
passages. Some applications require head bolts be coated with light
coat of engine oil.

during manufacture, some new type valves cannot be reground.
Resurface valve on proper angle specification using valve
grinding machine. Follow manufacturer's instructions for valve
grinding machine. Specifications may indicate a different valve face
angle than seat angle.
Measure valve margin after grinding. Replace valve if not
within specification. Valve stem tip can be refinished using valve
grinding machine.
Valve Lapping
During valve lapping of recent designed valves, be sure to
follow manufacturers recommendations. Surface hardening and materials
used with some valves do not permit lapping. Lapping process will
remove excessive amounts of the hardened surface.
Valve lapping is done to ensure adequate sealing between
valve face and seat. Use either a hand drill or lapping stick with
suction cup attached.
Moisten and attach suction cup to valve. Lubricate valve stem
and guide. Apply a thin coat of fine valve grinding compound between
valve and seat. Rotate lapping tool between the palms or with hand
drill.
Lift valve upward off the seat and change position often.
This is done to prevent grooving of valve seat. Lap valve until a
smooth polished seat is obtained. Thoroughly clean grinding compound
from components. Valve to valve seat concentricity should be checked.
See VALVE SEAT CONCENTRICITY.
CAUTION: Valve guides must be in good condition and free of carbon
deposits prior to valve seat grinding. Some engines contain
an induction hardened valve seat. Excessive material removal
will damage valve seats.
Valve Seat Grinding
Select coarse stone of correct size and angle for seat to be
ground. Ensure stone is true and has a smooth surface. Select correct
size pilot for valve guide dimension. Install pilot in valve guide.
Lightly lubricate pilot shaft. Install stone on pilot. Move stone off
and on the seat approximately 2 times per second during grinding
operation.
Select a fine stone to finish grinding operation. Grinding
stones with 30 and 60 degree angles are used to center and narrow the
valve seat as required. See Fig. 10.
Fig. 10: Adjusting Valve Seat Width - Typical
This Graphic For General Information Only
Valve Seat Replacement
Replacement of valve seat inserts is done by cutting out