1988 JEEP CHEROKEE oil change

Removal
1) Remove PCV valve hose at valve cover. Remove valve cover
bolts. Using a razor knife, cut RTV sealant along valve cover. Pry
upward on valve cover in areas marked "PRY HERE" near bolt hole areas.
2) Remove valve cover. Alternately loosen each rocker arm
bolt one turn at a time. Remove rocker arm assemblies and push rods.
Mark components for reassembly. Components must be installed in
original location.
Installation
Reverse removal procedures. Install rocker arm components in
original location. Tighten bolts to specification. Apply RTV sealant
on valve cover prior to installation.
VALVE SPRINGS
Valve springs can be removed without removing cylinder head.
Valve Spring Installed Height
Information not available from manufacturer.
HYDRAULIC VALVE LIFTERS
Removal
Remove rocker arms and push rods. See ROCKER ARMS & BRIDGE.
Using Lifter Remover/Installer (J-21884), remove lifter through push
rod openings of cylinder head. Mark lifter location for reassembly
reference. Replace lifters as an assembly if damaged. Internal
components cannot be interchanged.
Inspection
Inspect lifter and camshaft mating surfaces for wear. Check
cylinder block lifter bore diameter. Lifter bore diameter should be
within .9055-.9065" (22.999-23.025 mm). Replace parts as necessary.
Installation
Soak lifter assembly in engine oil supplement prior to
installation. Reverse removal procedures for installation. Install
lifter in original location.
ENGINE FRONT COVER
Removal
1) Disconnect negative battery cable. Remove drive belts, fan
and hub assembly. Remove pulley from vibration damper. Remove
vibration damper retaining bolt and washer.
2) Using Puller (J-21719-01), remove vibration damper and
key. Remove oil pan-to-front cover bolts. Remove cover-to-block
retaining bolts. Remove front cover.
3) Cut oil pan gasket even with face of cylinder block.
Remove gasket from oil pan. Pry crankshaft oil seal from cover.
Installation
1) Ensure all gasket surfaces are clean. Ensure oil slinger
is installed on crankshaft. Apply sealing compound on both sides of
front cover gasket. Install gasket on cylinder block. Replace front
section of oil pan seal with similar section fabricated from new seal.
2) Coat seal with RTV sealant and place in position. Apply
sealant to the joint area of oil pan and cylinder block. Place front
cover on cylinder block. Place Front Cover Seal Installer (J-22248) in\
front cover seal area.
3) Install all retaining bolts. Tighten bolts to

1) Drain cooling system. Remove fan shroud and drive belts.
Remove fan assembly.
2) Disconnect heater hoses and lower radiator hose at water
pump. Remove water pump retaining bolts. Remove water pump.
Installation
Clean all gasket surfaces. Install water pump. Tighten bolts
to specification. Ensure pump turns freely. Reverse removal
procedures. Fill and purge air from cooling system.
NOTE: It may be necessary to remove heater hose to remove trapped
air if system cannot be purged using following procedures.
Cooling System Air Purge (Vehicles With Coolant Recovery)
Fill system to proper level. Place heater control to "HEAT"
position and temperature control to "WARM" or "HIGH" position. Install
coolant caps. Operate engine to normal operating temperature. Shut off
engine and allow system to cool. Add coolant to recovery bottle.
Repeat procedure to obtain correct coolant level.
Cooling System Air Purge (Vehicles Without Coolant Recovery)
Fill system to proper level. Place heater control to "HEAT"
position and temperature control to "WARM" or "HIGH" position. Operate
engine to normal operating temperature with radiator cap removed. Add
necessary coolant and install radiator cap.
NOTE: For further information on cooling system capacities and
other cooling system components, see ENGINE COOLING SYSTEMS
article.
ENGINE OILING
CRANKCASE CAPACITY
Crankcase capacity is 4 qts. (3.8 L) with oil filter change.
NORMAL OIL PRESSURE
Normal oil pressure should be 13 psi (.91 kg/cm) at 600 RPM
or 37-75 psi (2.6-5.3 kg/cm) at 1600 RPM.
OIL PRESSURE REGULATOR VALVE
Oil pressure regulator valve is located in oil pump body and
is nonadjustable.
OILING SYSTEM
Engine lubrication is provided by the distributor driven
gear-type oil pump. Oil is supplied through the full-flow oil filter
and into an internal oil passage. Internal passage runs along right
side of block and intersects lifter bores.
Oil is then routed to camshaft and crankshaft bearings. Oil
is supplied to rocker arms from the hydraulic lifters and through the
push rods. By-pass valves are located in oil filter mounting and oil
pump.
OIL PUMP
Removal
Remove oil pan. See OIL PAN REMOVAL article. Remove oil pump

VALVE SPRING
Valve springs can be removed without removing cylinder head.
Valve Spring Installed
For 4.0L the Valve Spring Installed Height Specification is
1.625 inches or 41.29 mm. For the 4.2L the information is not
available from manufacturer.
HYDRAULIC VALVE LIFTER
Removal
Remove cylinder head. See CYLINDER HEAD. Using Lifter
Remover/Installer (J-21884), remove lifter. Mark lifter location for
reassembly reference. Replace lifters as an assembly if damaged.
Internal components cannot be interchanged.
Inspection
Inspect lifter and camshaft mating surfaces for wear. Check
cylinder block lifter bore diameter. Lifter bore diameter should be
within .9055-.9065" (22.999-23.025 mm). Replace parts as necessary.
Installation
Soak lifter assembly in engine oil prior to installation.
Reverse removal procedure for installation. Install lifter in original
location.
ENGINE FRONT COVER
Removal
1) Disconnect negative battery cable. Remove drive belts, fan
and hub assembly. Remove pulley from vibration damper. Remove
vibration damper retaining bolt and washer.
2) Using Puller (J-21719-01), remove vibration damper and
key. Remove alternator and A/C compressor bracket (if equipped).
Remove oil pan-to-front cover bolts. Remove cover-to-block retaining
bolts. Remove front cover.
3) Cut oil pan gasket tabs even with face of cylinder block.
Remove tabs. Remove gasket from oil pan. Pry crankshaft oil seal from
cover.
Installation
1) Ensure all gasket surfaces are clean. Ensure oil slinger
is installed on crankshaft. Apply sealing compound on both sides of
front cover gasket. Install gasket on cylinder block. Replace front
section of oil pan seal with similar section fabricated from new seal.
2) Coat seal with RTV sealant and place in position. Apply
sealant to the joint area of oil pan and cylinder block. Apply engine
oil on seal-to-oil pan contact areas.
3) Place front cover on cylinder block. Place Front Cover
Seal Installer (J-22248) in front cover seal area. Install all
retaining bolts. Tighten bolts to specification.
4) Install front cover oil seal. See FRONT COVER OIL SEAL in
this article. Remove front cover seal installer. Reverse removal
procedure for remaining components. Lubricate vibration damper
retaining bolt with oil prior to installation. Tighten bolts to
specification.
FRONT COVER OIL SEAL
1) Remove vibration damper. Pry seal from front cover. Use

Removal
Drain cooling system. Disconnect radiator and heater hoses
from pump. Remove drive belt(s). Remove fan shroud. Remove fan
assembly. Remove electric cooling fan (if equipped). Remove power
steering bracket from water pump. Remove water pump and gasket.
Installation
Ensure gasket surfaces are clean. Install water pump. Tighten
bolts to specification. Ensure pump turns freely. Reverse removal
procedures. Fill and purge air from cooling system.
NOTE: It may be necessary to remove heater hose to remove trapped
air if system cannot be purged using following procedures.
Cooling System Air Purge (Vehicles W/Coolant Recovery)
Fill system to proper level. Place heater control to "HEAT"
position and temperature control to "WARM" or "HIGH" position. Install
coolant caps. Operate engine to normal operating temperature. Shut off
engine and allow system to cool. Add coolant to recovery bottle.
Repeat procedure to obtain correct coolant level.
Cooling System Air Purge (Vehicles W/O Coolant Recovery)
Fill system to proper level. Place heater control to "HEAT"
position and temperature control to "WARM" or "HIGH" position. Operate
engine to normal operating temperature with radiator cap removed. Add
necessary coolant and install radiator cap.
NOTE: For further information on cooling systems, see appropriate
article in the ENGINE COOLING section.
LUBRICATION
CRANKCASE CAPACITY
Crankcase capacity for 4.0L is 5 1/2 qts. (5.2L) or 5 qts.
(4.7L) for 4.2L with oil filter change.
NORMAL OIL PRESSURE
Normal oil pressure should be 37-75 psi (2.6-5.3 kg/cm)
maximum above 1600 RPM. Minimum oil pressure should be 13 psi (.9
kg/cm
) at 600 RPM.
OIL PRESSURE REGULATOR VALVE
Oil pressure regulator valve is located in pump body. Valve
is nonadjustable and serviced as an assembly.
ENGINE OILING SYSTEM
Engine lubrication is provided by the distributor driven
gear-type oil pump. Oil is supplied through the full-flow oil filter
and into an internal oil passage. Internal passage provides oil to the
lifter bores. Oil is then routed to camshaft and crankshaft bearings.
Oil is supplied to rocker arms from the hydraulic lifters and through
the push rods.
OIL PUMP
Removal
Remove oil pan. See OIL PAN REMOVAL in this section. Remove

ECU signal line and the other end connected to ground. As throttle
valve angle changes, a return voltage is sent back to the ECU through
the third wire. Output voltage to the ECU is about one volt when
throttle valve is at idle position, and about 5 volts when throttle
valve is at wide open throttle.
A dual TPS is used on automatic transmission equipped models.
The additional sensor provides throttle position information to the
transmission.
Knock Sensor
A knock sensor is mounted on the lower left side of block,
just above the oil pan. This sensor detects abnormal engine vibration
due to "detonation" and/or "pre-ignition". The knock sensor supplies
detonation information to the ECU. The ECU then alters ignition timing
as needed to maintain maximum timing under most operating conditions.
Park/Neutral (P/N) Switch
The P/N switch is mounted in automatic transmission equipped
vehicles. The switch indicates when the transmission is in Park or
Neutral.
Speed Sensor
The speed sensor is a nonadjustable sensor attached to the
flywheel/drive plate housing with special shoulder bolts. This sensor
provides Top Dead Center (TDC) and engine speed information to the ECU\
by counting the flywheel teeth as they pass during engine operation.
The flywheel has a large trigger tooth and notch located 12 small
teeth before each TDC position. See Fig. 2.
Fig. 2: Design of Speed Sensor
When a small tooth and notch pass the magnetic core of the
sensor, the concentration and collapse of the magnetic field created
induces a small voltage spike into the sensor pick-up coil windings.

2) Loosen discharge port valve slightly. Loosen valve port
cap to allow refrigerant to force out air from compressor. Back-seat
the discharge valve and tighten the port cap. Compressor is ready for
service.
REFRIGERATION OIL
Only new, pure, moisture-free refrigeration oil should be
used in the air conditioning system. This oil is highly refined and
dehydrated (moisture content less than 10 parts per million).
Refrigeration oil container must be kept tightly closed at
all times when not in use, or moisture will be absorbed from the air
and introduced into the refrigeration system.
NIPPONDENSO 10-CYLINDER
SHAFT SEAL
NOTE: Check compressor refrigerant oil level when replacing seals.
See COMPRESSOR REFRIGERANT OIL CHECKING article in this
section.
Removal
1) Hold clutch hub stationary and remove center nut. Screw
remover into center of hub. Turn center bolt to remove pressure plate.
2) Remove shims from shaft. Remove snap ring from inside of
pulley. Tap pulley off of shaft with plastic mallet. Be careful not
to distort pulley while removing.
3) Disconnect clutch coil wires from compressor housing.
Remove snap ring inside coil and lift coil off compressor. Pry dust
seal out from around compressor shaft (if equipped).
4) Place shaft key remover on shaft and turn to remove key.
Remove drain plug (if equipped). Remove bolts holding service valves
to body of compressor and remove valves. Discard "O" rings. Drain oil
out of compressor.
5) Remove 6 through bolts from front head of compressor and
discard washers. Tap head loose from compressor, being careful not to
scratch sealing surfaces. Remove snap ring (if equipped) from front
housing. Press seal plate out. Remove seal from shaft. See Fig. 1.
Installation
1) Lubricate shaft seal with clean refrigerant oil. Place on
compressor shaft. Lubricate seal plate (and "O" ring, if equipped) and\
install in front housing. Install snap ring (if equipped).
2) Place front housing on compressor body. Using new
washers, install through bolts. Tighten bolts evenly and alternately
to 18 ft. lbs. (24 N.m). Install shaft key with installer and plastic
mallet. Insert dust seal into front of compressor.
3) Install drain plug using new gasket. Add correct amount
of refrigerant oil to compressor. If service valves were removed,
coat new "O" rings with refrigerant oil and install service valves.
4) Place clutch coil on compressor and install snap ring.
Install shims on shaft to adjust clearance between pressure plate and
rotor to .016-.028" (.41-.71 mm). Tighten shaft nut to 12 ft. lbs. (1\
6
N.m). See REFRIGERANT OIL & R-12 SPECIFICATIONS table for system
capacities.
SANKYO/SANDEN 5-CYLINDER COMPRESSOR SERVICING
NOTE: During the past year, Sankyo International (USA), Inc. has
changed its name to Sanden International (USA), Inc.

PINION DEPTH
1) Depth Gauge Set (D-271) is used to determine pinion depth\
.
Place Master Pinion Block (D-139 on Model 44; D-120 on Model 60 and
61; D-137 on Model 70; T80T-4020-F42 on Model 80) in pinion bore of
carrier. Put Arbor Discs (D-115-4-44 on Model 44; D-116-2 on Models
60,61 and 70; (T88T-4020-A) on Arbor (D-115-3). Install arbor in
carrier with discs riding in bearing bore.
2) Put Pinion Height Block (D-115-1-44 on Model 44; D-116-1
on Models 60, 61, 70 and 80) on top of master pinion block with side
against arbor. Place Scooter Block (115-2) with Dial Indicator (D-106\
-
5) on small step of pinion height block. Zero dial indicator with
scooter block flat on pinion height block.
3) Move scooter block so dial indicator tip touches arbor.
Move block back and forth (perpendicular to arbor) to get highest
reading. This reading, plus or minus value etched on pinion head, is
thickness of shim pack necessary for pinion bearing.
4) On Model 80, Use Gauge Tube (D81T-4020-F51) and Gauge
Block (D81T-4020-F56) to determine required thickness of shim pack.
5) On all models, measure shims separately with micrometer.
If baffle is used, its thickness must be included in shim pack. This
is also true if slinger is used between inner bearing and head of
pinion shaft. Place pinion height shim pack in carrier bore for inner
bearing race. Drive bearing race into carrier, making sure cup is
fully seated.
PINION BEARING PRELOAD
1) Drive outer pinion bearing into carrier housing. Press
inner pinion bearing onto pinion shaft using Press Tube (C-3095-A).
Ensure bearing seats fully. Insert pinion shaft into carrier. Install
outer bearing, slinger (if equipped), flange, washer and nut.
NOTE: Pinion preload shims and oil seal should NOT be installed at
this time.
2) Using an INCH lb. torque wrench, tighten pinion nut until
10 INCH lbs. (1.13 N.m) rotational torque is required to move pinion
shaft. Recheck pinion depth with arbor and discs at this time. Place
pinion height block on face of pinion shaft.
3) Place dial indicator on small step of height block for
Model 44, 60 and 61 axles. Place dial indicator on high step of block
for Models 70 and 80 axles. Zero dial indicator and move it across
arbor to get highest reading. If reading is within .002" (.05 mm) of
etching on pinion face, pinion depth is correct.
NOTE: If pinion depth is not with .002" (.05 mm) of etched number
on face of pinion, shim pack under inner bearing race must
be changed before proceeding with differential settings.
4) Remove pinion nut, washer, flange, slinger and outer
bearing. Place preload shims (removed during disassembly) on pinion.
Install bearing and slinger. After lightly coating lips with gear oil,
install pinion seal in carrier housing. Install flange, washer and NEW
pinion nut. Tighten nut to specification. See TORQUE SPECIFICATIONS
table at end of this article.
5) Using an INCH lb. torque wrench, measure preload
(rotational torque) of pinion shaft. Rotational torque required to
keep pinion shaft turning freely and smoothly should be 20-40 INCH
lbs. (2.3-4.5 N.m). If preload needs to be increased, remove a few
shims and recheck. To decrease preload, add a few shims and recheck.
See Fig. 14 .

install rear bearing cup. See Fig. 3.
NOTE: Replacement pinion gears marked more than .009" (.23 mm)
should not be used.
15) See PINION DEPTH SHIM ADJUSTMENT SPECIFICATIONS to
determine appropriate starter shim thickness when installing NEW gear
sets. Note pinion variance numbers on new and old gear. Follow old
pinion marking line across to new pinion marking column.
16) The number in box indicates change in shim thickness from
original. For example, old pinion marked "-3" and new pinion marked
"+2". Intersecting box shows -.005" (.13 mm) to be subtracted from
original shim thickness.
17) Starter shim thickness must not be used as a final shim
setting. An actual pinion depth measurement must be made and final
shim thickness should be adjusted as necessary.
Fig. 4: Measuring Pinion Depth
DRIVE PINION BEARING PRELOAD
1) Install new collapsible spacer and front bearing on drive
pinion. Install oil seal, yoke and nut. Tighten pinion nut only enough
to remove bearing end play.
CAUTION: Never reuse collapsible spacer.