1987 MAZDA 626 fuel pump

4A FUEL SYSTEM
[FE 8Valve (Except General) and F6]
Assemble in the sequence shown in the figure, referring to the assembly note for specially marked parts.
1. Throttle body
2. Main body
3. Secondary ven-
turi and nozzle
4. Primary venturi
and nozzle
5. Injector weight
©Air bleeds and
jets
7. Solenoid valve
and idle switch
(If equipped)
8. Slow fuel cut
solenoid valve
9. Accelerator
pump
10. Needle valve
11. Secondary di-
aphragm
12. Float
13. Air horn, choke
breaker di-
aphragm, and
choke opener (If
equipped)
14. Lever
'3
©
76G04A-032
Assembly note
Air bleeds and jets
1. Step jet and plug
2. Secondary step air bleed (No. 1) (Fixed type)
3. Secondary main air bleed
4. Secondary main jet
5. Power jet
6. Primary main jet
7. Primary main air bleed
8. Primary slow air bleed (No. 1)
9. Primary slow jet and plug
10. Primary slow air bleed (No. 2)
76G04A-033
4A-30

FUEL SYSTEM 4A
76G04A-034
Inspection
Note
a) Clean all parts with carburetor cleaner and
dry with compressed air.
b) Do not use a wire to clean the jets.
Check the following and replace any faulty parts.
1. Damaged air horn, main body, or throttle body
2. Improper operation of the choke valve or throttle
valve
3. Damaged float
4. Needle valve damage or improper seating
5. Clogged or damaged jet or air bleed
6. Damaged piston cup in the accelerator pump
7. Weakened or broken spring
8. Damaged diaphragm
9. Improper solenoid operation
76G04A-191
Primary throttle valve
(0.248—0.327 in)
When secondary throttle valve
begins to open
Secondary Throttle Valve
1. Check the clearance between the primary throttle
valve and wall when lever A contacts lever B.
>
L_ Clearance:
7.3—8.3 mm (0.248—0.327 in)
7.3—8.3 mm
76G04A-035
3. If not within specification, adjust it by bending
lever A.
76G04A-036
4 A—31

FUEL SYSTEM 4 A
76G04A-048
76G04A-049
FUEL PUMP
Inspection
Fuel pressure
1. Disconnect the hose at the carburetor and connect
a fuel pressure gauge.
2. Disconnect the fuel return hose from the fuel pump
and plug the fuel pump return pipe as shown in
the figure,
3. Measure the pressure while the engine is idling.
Replace the pump, if necessary.
FE & F8 (ECE,
Hong Kong,
Singapore)
Others
Pressure kPa
(kg/cm2, psi)
20—29 (0.2-0.3, 2.8-4.3)
20-26
(0.20-0.27,
2.8-3.8)
Flow rate (volume)
1. Disconnect the carburetor fuel hose and insert the
end into a measuring breaker.
2. Disconnect the fuel return hose from the fuel pump
and plug the fuel pump return pipe as shown in
the figure.
3. Start the engine and measure the amount of fuel
pumped per minute.
Volume: More than 860 cc (52.5 cuin)/min
Removal
1. Remove in the following order.
(1) Fuel outlet hose
(2) Fuel inlet hose
(3) Fuel return hose
(4) Fuel pump
(5) Gasket
(6) Insulator
(7) Gasket
76G04A-050
Installation
Install in the reverse order of removal.
Caution
a) Replace the gasket whenever the fuel pump
is replaced.
b) Be sure to connect the hoses in the correct
positions.
Check for leaks.
76G04A-051
4A—35
expert22 fl/i* http://rutracker.org

FUEL SYSTEM 4A
SEPARATOR
Inspection
Visually check the separator for fuel leakage and dam-
age. Replace, if necessary.
76G04A-055
TWO-WAY CHECK VALVE
(Except Middle East)
Inspection
1. Disconnect the hoses, and remove the check
valve.
2. Check that air flows in both directions through the
valve.
3. If not as specified, replace the two-way check
valve.
76G04A-056
THREE-WAY CHECK VALVE
(Middle East)
1. Blow through the valve from port and check
that air comes out of port (§).
Next, block port ©and check that air comes of
port ©.
2. Block port ©and apply vacuum with a vacuum
pump through port
3. Check that no vacuum is held.
76G04A-057
FUEL FILTER
Replacement
The fuel filter is mounted on the left side of the frame.
Caution
a) To prevent gasoline from draining during
removal, first disconnect and plug the in-
let hose.
b) During installation be sure to install the fuel
filter in the correct direction of flow.
76G04A-058
4 A—37

PURGE CONTROL SYSTEM 4 A
PURGE CONTROL SYSTEM
[FE 8VALVE—UNLEADED FUEL]
Vaccum switch valve -4
I
Water thermo valve
76G04A-120
This system supplies additional air to the intake manifold to improve the driveability when the engine
coolant temperature is above 50°C (122°F).
TROUBLESHOOTING
Possible cause Vacuum switch valve Water thermo valve
Page 4A—63 4A—66
Checking order 1 2
VACUUM SWITCH VALVE
1. Connect a vacuum pump to the purge control
valve as shown in the figure.
2. Blow through the valve from port A and check that
air does not come out of port B.
3. Apply 100 mm-Hg (3.94 InHg) vacuum.
4. Blow through port A and check that air comes out
of port B.
5. Replace if necessary.
76G04A-121
4A-63

4A CONTROL SYSTEM
Idle switch
Adjust screw
76G04A-180
76G04A-181
5. Increase the engine speed to more than 2,000 rpm
and decelerate gradually.
6. Check the voltage.

Specification
Engine speed
^^^

FE 8Valve—
Unleaded Fuel
& F6 Sin-
gapore
Others
At idle below 1,5V Battery voltage
Above 1,000—1,100 rpm Battery voltage below 1.5V

7. If the voltage is not within specification, turn the ad-
just screw to adjust.
VACUUM SWITCH
On-Vehicle Inspection
1. Run the engine at idle.
2. Connect a voltmeter to the vacuum switch connec-
tor terminal wire (LB).
Voltage: Approx. 12V
3. Disconnect the vacuum hose from the vacuum
switch, and plug it.
4. Check the voltage.
Voltage: Less than 1.5V
Off-Vehicle Inspection
Inspection
1. Remove the vacuum switch.
2. Connect a vacuum pump to the vacuum switch.
3. Connect an ohmmeterto the vacuum switch, and
check the continuity between the switch terminals.

Vacuum Continuity
MTX: More than 300 mmHg (11.8 inHg) No ATX: More than 200 mmHg (7.9 inHg) No
Others Yes

76G04A-182
4A—94

FUEL AND EMISSION
CONTROL SYSTEMS
(FUEL INJECTION FE)
OUTLINE 4B— 2
SYSTEM DIAGRAM 4B— 2
COMPONENT LOCATION 4B— 3
VACUUM HOSE ROUTING
DIAGRAM 4B— 5
SPECIFICATIONS 4B— 6
TROUBLESHOOTING GUIDE 4B— 7
TROUBLESHOOTING
PROCEDURE 4B— 7
TROUBLESHOOTING WITH SST.... 4B— 9
INSPECTION PROCEDURE 4B—10
AFTER-REPAIR PROCEDURE 4B—10
PRINCIPLE OF CODE CYCLE 4B—12
CODE NUMBER 4B—13
SWITCH MONITOR FUNCTION 4B—25
INSPECTION PROCEDURE 4B—26
IDLE SPEED 4B—29
IDLE MIXTURE 4B—29
INTAKE AIR SYSTEM 4B—30
COMPONENT DESCRIPTIONS 4B—30
REMOVAL 4B—31
PARTS INSPECTION 4B—32
INSTALLATION 4B—34
IDLE-UP SYSTEM 4B—35
COMPONENT DESCRIPTIONS 4B—36
TROUBLESHOOTING 4B—37
AIR VALVE 4B—38
AIR BYPASS SOLENOID VALVE ... 4B—39
FUEL SYSTEM 4B—42
COMPONENT DESCRIPTIONS 4B—43
TROUBLESHOOTING 4B—44
FUEL PRESSURE RELEASE AND
SERVICING FUEL SYSTEM 4B—45
MULTI-PRESSURE TESTER 4B—46
FUEL PRESSURE 4B—48
FUEL PUMP 4B—49
PULSATION DAMPER 4B—50
INJECTOR 4B—51
PRESSURE REGULATOR
CONTROL SYSTEM 4B—53
COMPONENT DESCRIPTIONS 4B—54
TROUBLESHOOTING 4B—55
REPLACEMENT 4B—57
FUEL TANK 4B—61
DECELERATION CONTROL
SYSTEM 4B—64
COMPONENT DESCRIPTIONS 4B—65
TROUBLESHOOTING 4B—66
AIR INJECTION SYSTEM 4B—68
COMPONENT DESCRIPTIONS 4B—68
TROUBLESHOOTING 4B—69
EXHAUST GAS RECIRCULATION
(EGR) SYSTEM 4B—71
COMPONENT DESCRIPTIONS 4B—71
TROUBLESHOOTING 4B—72
EVAPORATIVE EMISSION
CONTROL (EEC) SYSTEM 4B—74
COMPONENT DESCRIPTIONS 4B—74
TROUBLESHOOTING 4B—75
POSITIVE CRANKCASE
VENTILATION (PCV) SYSTEM 4B—80
COMPONENT DESCRIPTION 4B—80
EXHAUST SYSTEM 4B—81
REMOVAL AND INSTALLATION ... 4B—82
INSPECTION 4B—82
CONTROL SYSTEM 4B—83
RELATIONSHIP CHART 4B—84
EGI MAIN FUSE 4B—86
MAIN RELAY 4B—86
CIRCUIT OPENING RELAY 4B—86
ENGINE CONTROL UNIT 4B—87
NEUTRAL SWITCH 4B—91
CLUTCH SWITCH 4B—91
BRAKE LIGHT SWITCH 4B—91
P/S PRESSURE SWITCH 4B—92
INHIBITOR SWITCH 4B—92
E/L CONTROL UNIT 4B—93
AIR FLOW METER 4B—94
THROTTLE SENSOR 4B—95
WATER THERMO SENSOR 4B—97
WATER THERMO SWITCH 4B—97
OXYGEN SENSOR 4B—98
ATMOSPHERIC PRESSUFfE
SENSOR 4B—99
76G04B-001

4B OUTLINE
SPECIFICATIONS
Item Specification

Idle speed rpm MTX: 800 +5„° (Neutral), ATX: 900 +5S
(P
range)

Throttle body

Type Horizontal draft (1 -barrel)
Throat diameter mm (in) 50 (2.0)

Air flow meter

E2-VS More than
20

E2-VC 100-300
Resistor
Q
E2-VB 200—400 Resistor
Q

E2-THA -20°C
(
—4°F) 13,600-18,400 20°C
(
68°F) 2,210-2,690 60°C (140°F)
493- 667
Air cleaner

Element type Oil permeated

Fuel pump

Type Impeller
(in
tank)
Output pressure kPa (kg/cm2,
psi)
441-588 (4.5-6.0, 64—85)
Feeding capacity cc (cu in)/10 sec. 220 (13.4) minmum

Fuel filter

Type Low pressure side Nylon element Type High pressure side Paper element

Pressure regulator

Type Diaphragm
Regulating pressure kPa (kg/cm2,
psi)
235-275 (2.4—2.8, 34—40)

Injector
TvDe
Hiqh-ohmic
Type
of
drive Voltage
Resistance
fi
12-16
Injection amount cc (cu
in) 15
seconds 38—53 (2.3-3.2)

Fuel tank

Capacity liters (US gal, Imp gal) 60 (15.9, 13.2)

Fuel

Soecification Unleaded reaular

76G04B-506
4B—6