1987 MAZDA 626 ECO mode
[x] Cancel search: ECO modePage 1785 of 1865
16 OUTLINE
OUTLINE
AIR DISTRIBUTION
Vehicles with air conditioner
Side ventilator outlet
1
Center ventilator outlet
- Defroster = outlet
FRESH air inlet
REC air inlet
Side . ventilator < outlet
Floor outlet
Temperature control lever
*
REC-FRESH air selector lever
•QDOODDDaaacziciz) ^^^ ° cQ^
^J 'i, *
OFF
1 7 3 4
Mode control lever
Mode control switch
A/C
DECO
Blower switch
REC-FRESH air selector switch
«?/ ^ W ^
izzi • izn •
C^) A/C - ECDN
• CUD
<=i ac3 a ua • • Jf OFF 12 3 4. SJ
Temperature control lever Blower switch
69G16X002
16-2
Page 1818 of 1865
30 TECHNICAL DATA
Item Engine model FE 12-valve
Top 0.20—0.35 (0.008-0.0138)
End gap measured
in
cylinder
mm
(in) Second 0.15—0.30 (0.006-0.012) End gap measured
in
cylinder
mm
(in) Oil (rail) 0.20-0.70 (0.008-0.0276)
Maximum 1.0 (0.039)
Top 1.52-1.54 (0.0598-0.0606)
Ring groove width
in
piston mm (in) Second 1.52-1.54 (0.0598-0.0606)
Oil 4.02-4.04 (0.1583-0.1591)
Top 0.03—0.07 (0.0012—0.0028) Clearance
ot
piston ring
to
ring Second 0.03—0.07 (0.0012-0.0028)
Maximum 0.15(0.006)
Piston pin
Diameter mm (in) 21.974-21.980 (0.8651-0.8654)
Interference
in
connecting
rod
mm (in) 0.013-0.037 (0.0005-0.0015)
Piston
to
piston pin clearance mm (in) 0.008-0.024 (0.0003—0.0009)
Installation pressure N (kg,
lb)
4,900-14,700 (500-1,500, 1,100-3,300)
Connecting rod and connecting rod bearing
Length (Center
to
center) mm (in) 151.95—152.05 (5.982—5.986)
Twisting and bending mm (in) 0.06 (0.0024) max.
Small end bore mm (in) 21.943—21.961 (0.8640-0.8646)
Big end bore mm (in) 54.002-54.017 (2.1261—2.1266)
Big end width mm (in) 26.838-26.890 (1.0566—1.0587)
Connecting rod side clearance
mm
(in) Standard 0.110-0.262 (0.004-0.010) Connecting rod side clearance
mm
(in) Maximum 0.30 (0.012)
Crankshaft
Crankshaft runout mm (in) Maximum 0.03 (0.0012)
Standard size 59.937-59.955 (2.3597—2.3604)
0.25 (0.010) Standard 59.693-59.711 (2.3501-2.3508)
Main journal diameter mm (in)
undersize No.3 59.687-59.705 (2.3499-2.3506) Main journal diameter mm (in) 0.50 (0.020) No. 1,2,4,5 59.443-59.461 (2.3403-2.3410) Main journal diameter mm (in) undersize No.
3
59.437-59.455 (2.3400-2.3407)
0.75 (0.030) No. 1,2,4,5 59.193-59.211 (2.3304-2.3311)
undersize No.
3
59.187-59.205 (2.3302-2.3309)
Main journal taper and out-of-round mm (in) Maximum 0.05 (0.0020)
Standard 50.940-50.955 (2.0055-2.0061)
Crankpin diameter 0.25 (0.010) undersize 50.690—50.705 (1.9957-1.9963)
mm (in) 0.50 (0.020) undersize 50.440-50.455 (1.9858-1.9864)
0.75 (0.030) undersize 50.190-50.205 (1.9760-1.9766)
Crankpin taper and out-of-round
mm (in)
Maximum 0.05 (0.0020)
Main bearing
No. 1,2,4,5 Standard 0.025-0.043 (0.0010—0.0017)
Main journal bearing
oil
No. 1,2,4,5 Maximum 0.08 (0.0031) clearance
mm
(in) No.
3
Standard 0.031—0.049 (0.0012—0.0019) No.
3
Maximum 0.08 (0.0031)
Available undersize bearing mm fin} 0.25 (0.010), 0.50 (0.020), 0.75 (0.030)
Crankpin bearing
Crankpin bearing
oil
clearance
mm
(in) Standard 0.027-0.067 (0.0011-0.0026) Crankpin bearing
oil
clearance
mm
(in) Maximum 0.10 (0.0039)
Available undersize bearina mm (in) 0.25 (0.010), 0.50 (0.020), 0.75 (0.030)
Thrust bearing (center main bearing)
Crankshaft end play mm (in) Standard 0.08-0.18 (0.0031-0.0071) Crankshaft end play mm (in) Maximum 0.30 (0.0118)
Standard 27.94-27.99 (1.100-1.102)
Bearing width
mm (in)
0.25 (0.010) oversize 28.04-28.09 (1.104-1.106) Bearing width
mm (in)
0.50 (0.020) oversize 28.12-28.17 (1.107-1.109)
0.75 (0.030) oversize 28.20—28.25 (1.110—1.112)
30—4
Page 1821 of 1865
TECHNICAL DATA 30
—Engine model
Item -
FE 8-valve
F8 F6
—Engine model
Item -
ECE Middle East General
F8 F6
0.75 (0.030) oversize
—
81.694—81.714
(3.2163-3.2171)
1.00 (0.039) oversize
—
81.944—81.964 (3.2261-3.2269)
Piston and cylinder clearance
mm
(in) Standard 0.036-0.075 (0.0014—0.0030) Piston and cylinder clearance
mm
(in) Maximum 0.15 (0.0059)
Piston ring
Thickness
mm
(in) Top 1.47-1.49 (0.0579-0.0587) Thickness
mm
(in) Second 1.47-1.49 (0.0579—0.0587)
End gap measured
in
cylinder
mm (in)
Top 0.20—0.35 (0.008—0.0138)
End gap measured
in
cylinder
mm (in)
Second 0.15-0.30 (0.006-0.012) End gap measured
in
cylinder
mm (in)
Oil (rail) 0.20—0.70 (0.008—0.0276) End gap measured
in
cylinder
mm (in)
Maximum 1.0 (0.039)
Ring groove width
in
piston
mm
(in)
Top 1.52—1.54 (0.0598-0.0606)
Ring groove width
in
piston
mm
(in) Second 1.52-1.54 (0.0598-0.0606) Ring groove width
in
piston
mm
(in)
Oil 4.02-4.04 (0.1583-0.1591)
Clearance
of
piston ring
to
ring
groove
mm
(in)
Top 0.03-0.07 (0.0012-0.0028) Clearance
of
piston ring
to
ring
groove
mm
(in) Second 0.03-0.07 (0.0012-0.0028) Clearance
of
piston ring
to
ring
groove
mm
(in) Maximum 0.15 (0.006)
Piston pin
Diameter
mm
(in) 21.974—21.980 (0.8651—0.8654)
Interference
in
connecting
rod mm
(in) 0.013—0.037 (0.0005—0.0015)
Piston
to
piston pin clearance
mm
(in) 0.008—0.024 (0.0003-0.0009)
Installation pressure
N
(kg,
lb)
4,900—14,700 (500—1,500, 1,100—3,300)
Connecting rod and connecting rod bearing
Length (Center
to
center)
mm
(in) 151.95-152.05 (5.982-5.986) 135.95—136.05
(5.352-5.356)
Twisting and bending
mm
(in) 0.06 (0.0024) max.
Small end bore
mm
(in) 21.943-21.961 (0.8640-0.8646)
Big end bore
mm
(in) 54.002-54.017 (2.1261—2.1266)
Bia end width
mm
(in) 26.838-26.890 (1.0566—1.0587)
Connecting rod side clearance
mm
(in) Standard 0.110-0.262 (0.004—0.010) Connecting rod side clearance
mm
(in) Maximum 0.30 (0.012)
Crankshaft
Crankshaft runout mm (in)
I
Maximum 0.03 (0.0012)
Main journal diameter
mm (in)
Standard size 59.937-59.955 (2.3597—2.3604)
Main journal diameter
mm (in)
0.25 (0.010) undersize
Standard 59.693—59.711 (2.3051—2.3508)
Main journal diameter
mm (in)
0.25 (0.010) undersize No.
3
59.687—59.705 (2.3499-2.3506) Main journal diameter
mm (in) 0.50 (0.020) undersize
No. 1,2,4,5 59.443-59.461 (2.3403—2.3410) Main journal diameter
mm (in) 0.50 (0.020) undersize No.
3
59.437-59.455 (2.3400—2.3407)
Main journal diameter
mm (in)
0.75 (0.030)
undersize
No. 1,2,4,5 59.193-59.211 (2.3304—2.3311)
Main journal diameter
mm (in)
0.75 (0.030)
undersize No.
3
59.187—59.205 (2.3302—2.3309)
Main journal taper and out-of-round mm (in) Maximum 0.05 (0.0020)
Crankpin diameter mm (in)
Standard 50.940-50.955 (2.0055-2.0061)
Crankpin diameter mm (in)
0.25 (0.010) undersize 50.690-50.705 (1.9957-1.9963) Crankpin diameter mm (in) 0.50 (0.020) undersize 50.440-50.455 (1.9858-1.9864) Crankpin diameter mm (in)
0.75 (0.030) undersize 50.190—50.205 (1.9760-1.9766)
Crankpin taper and out-of-round
mm
(in) Maximum 0.05 (0.0020)
Main bearlna
Main journal bearing
oil
clearance
mm
(in)
No. 1,2,4,5 Standard 0.025-0.043 (0.0010-0.0017)
Main journal bearing
oil
clearance
mm
(in)
No. 1,2,4,5 Maximum 0.08 (0.0031) Main journal bearing
oil
clearance
mm
(in) No.
3
Standard 0.031—0.049 (0.0012—0.0019)
Main journal bearing
oil
clearance
mm
(in) No.
3
Maximum 0.08 (0.0031)
Available undersize bearina
mm
(in) 0.25 (0.010), 0.50 (0.020), 0.75 (0.030)
Crankpin bearing
Crankpin bearing
oil
clearance
mm
(in) Standard 0.027-0.067(0.0011 -0.0026) Crankpin bearing
oil
clearance
mm
(in) Maximum 0.10 (0.0039)
Available undersize bearing
mm
(in) 0.25 (0.010), 0.50 (0.020), 0.75 (0.030)
30-7
Page 1823 of 1865
TECHNICAL DATA 30
——Engine model
Item -
FE DOHC ——Engine model
Item -Leaded fuel Unleaded fuel
Valve seat
Seat angle IN 45° Seat angle EX 45°
Seat contact width
mm
(in) IN 1.2-1.6 (0.047-0.063) Seat contact width
mm
(in) EX 1.2-1.6 (0.047-0.063)
Seat sinking (Measure valve protruding length) mm (in)
IN Standard 36.8 (1.449) Seat sinking (Measure valve protruding length) mm (in)
IN Maximum 37.8 (1.488) Seat sinking (Measure valve protruding length) mm (in) EX Standard 36.8 (1.449)
Seat sinking (Measure valve protruding length) mm (in) EX Maximum 37.8 (1.488)
Valve spring
Free length mm (in)
Outer Standard 39.1 (1.539)
Free length mm (in)
Outer Minimum 38.7 (1.524) Free length mm (in)
Inner Standard 38.0 (1.496) Free length mm (in)
Inner Minimum 37.7 (1.484)
Out-of-square
mm
(in) Maximum Outer 1.4 (0.055), Inner 1.3 (0.051)
Setting load/height
N
(kg, lb)/mm
(in)
Outer 78 (8.0, 17.6)/31.5 (1.240) Setting load/height
N
(kg, lb)/mm
(in)
Inner 123 (12.5, 27.5)/33.0 (1.299)
Camshaft
Cam lobe height
mm (in)
IN Standard 45.005-45.105 (1.772-1.776) 45.002-45 102 (1.772-1.776)
Cam lobe height
mm (in)
IN Minimum 44.855 (1.7659) 44.852 (1.7658) Cam lobe height
mm (in)
EX Standard 45.005—.45.105 (1.772-1.776) 45.002-45.102 (1.772-1.776) Cam lobe height
mm (in)
EX Minimum 44.855 (1.7659) 44.852 (1.7658)
Journal diameter
mm
(in) 29.940-29.965 (1.1787-1.1797) Journal diameter
mm
(in) Out-of-round
|
Maximum 0.05 (0.002)
Camshaft bearing
oil
clearance mm (in) 0.035-0.085 (0.0014-0.0033) Camshaft bearing
oil
clearance mm (in) Maximum 0.15 (0.0059)
Camshaft runout
mm (in)
Maximum 0.03 (0.0012)
Camshaft end play
mm
(in) Standard 0.08-0.10 (0.003-0.004) Camshaft end play
mm
(in) Maximum 0.20 (0.008)
Cylinder block
Height
mm
(in) 289.0 (11.38)
Distortion
mm
(in) Maximum 0.15 (0.006)
Grindino limit
mm
fin) 0.20 (0.008)
Cylinder bore diameter mm (in)
Standard 86.000—86.019 (3.3858-3.3866) Cylinder bore diameter mm (in) 0.25 (0.010) oversize 86.250—86.269 (3.3957—3.3964) Cylinder bore diameter mm (in) 0.50 (0.020) oversize 86.500-86.519 (3.4055-3.4062)
Cylinder bore taper and out-of-round mm (in) Maximum 0.019 (0.0007)
Piston
Piston diameter measured at 90°
to pin
bore axis and 18.0
mm
(0.709
in)
below oil ring groove
mm (in)
Standard 85.944-85.964 (3.3836-3.3834) Piston diameter measured at 90°
to pin
bore axis and 18.0
mm
(0.709
in)
below oil ring groove
mm (in)
0.25 (0.010) oversize 86.194-86.214 (3.3935-3.3942)
Piston diameter measured at 90°
to pin
bore axis and 18.0
mm
(0.709
in)
below oil ring groove
mm (in) 0.50 (0.020) oversize 86.444-86.464 (3.4033-3.4041)
Piston
to
cylinder clearance
mm
(in) Standard 0.036-0.075 (0.0014-0.0030) Piston
to
cylinder clearance
mm
(in) Maximum 0.15 (0.0059)
Piston ring
Thickness mm (in)
TOD
1.47-1.49 (0.0579-0.0587) Thickness mm (in) Second 1.47-1.49 (0.0579-0.0587)
30-9
Page 1824 of 1865
30 TECHNICAL DATA
~ ———Engine model
Item ~ . _
FE DOHC ~ ———Engine model
Item ~ . _ Leaded fuel Unleaded fuel
End gap measured
in
cylinder
mm
(in)
Top 0.20-0.35 (0.008-0.0138)
End gap measured
in
cylinder
mm
(in) Second 0.15-0.30 (0.006-0.012) End gap measured
in
cylinder
mm
(in) Oil (rail) 0.20-0.70 (0.008-0.0276) End gap measured
in
cylinder
mm
(in)
Maximum 1.0 (0.039)
Ring groove width
in
piston
mm (in)
Top 1.52-1.54 (0.0598—0.0606)
Ring groove width
in
piston
mm (in)
Second 1.52-1.54 (0.0598-0.0606) Ring groove width
in
piston
mm (in)
Oil 4.02-4.04 (0.1583—0.1591)
Clearance
of
piston ring
to
ring
groove
mm
(in)
Top 0.03-0.07 (0.0012-0.0028) Clearance
of
piston ring
to
ring
groove
mm
(in) Second 0.03-0.07 (0.0012-0.0028) Clearance
of
piston ring
to
ring
groove
mm
(in) Maximum 0.15 (0.006)
Piston pin
Diameter
mm (in)
21.987-21.993 (0.8656-0.8659)
Connecting rod
to
piston pin clearance
mm (in)
0.010-0.027 (0.0004-0.0011)
Piston
to
piston pin clearance
mm
(in) -0.005-0.011 (-0.0002-0.0004)
Connecting rod and connecting rod bearing
Length (Center and center)
mm (in)
149.95—150.05 (5.904-5.907)
Twisting and bending
mm
(in) 0.06 (0.0024) max.
Small end bore
mm (in)
22.003-22.014 (0.8663-0.8667)
Big end bore
mm (in)
54.002-54.017 (2.1261-2.1266)
Big end width
mm
(in) 26.838-26.890 (1.0566-1.0587)
Connecting rod side clearance
mm
(in) Standard 0.110-0.262 (0.004-0.010) Connecting rod side clearance
mm
(in) Maximum 0.30 (0.012)
Crankshaft
Crankshaft runout
mm (in)
Maximum 0.03 (0.0012)
Main journal diameter mm (in)
Standard size 59.937-59.955 (2.3597-2.3604)
Main journal diameter mm (in)
0.25 (0.010)
undersize
Standard 59.693—59.711 (2.3051-2.3508)
Main journal diameter mm (in)
0.25 (0.010)
undersize No.
3
59.687-59.705 (2.3499-2.35061 Main journal diameter mm (in) 0.50 (0.020)
undersize
No. 1,2,4,5 59.443-59.461 (2.3403-2.3410) Main journal diameter mm (in) 0.50 (0.020)
undersize No.
3
59.437-59.455 (2.3400-2.3407)
Main journal diameter mm (in)
0.75 (0.030)
undersize
No. 1,2,4,5 59.193-59.211 (2.3304-2.3311)
Main journal diameter mm (in)
0.75 (0.030)
undersize No.
3
59.187-59.205 (2.3302-2.3309)
Main journal taper and out-of-round mm (in) Maximum 0.05 (0.0020)
Crankpin diameter
mm
(in)
Standard 50.940-50.955 (2.0055-2.0061)
Crankpin diameter
mm
(in) 0.25 (0.010) undersize 50.690-50.705 (1.9957-1.9963) Crankpin diameter
mm
(in) 0.50 (0.020) undersize 50.440-50.455 (1.9858-1.9864) Crankpin diameter
mm
(in)
0.75 (0.030) undersize 50.190-50.205 (1.9760-1.9766)
Crankpin taper and out-of-round
mm
(in) Maximum 0.05 (0.0020)
Main bearing
Main journal bearing
oil
clearance
mm
(in)
No. 1,2,4,5 Standard 0.025-0.043 (0.0010-0.0017)
Main journal bearing
oil
clearance
mm
(in)
No. 1,2,4,5 Maximum 0.08 (0.0031) Main journal bearing
oil
clearance
mm
(in) No.
3
Standard 0.031-0.049 (0.0012-0.0019)
Main journal bearing
oil
clearance
mm
(in) No.
3
Maximum 0.08 (0.0031)
Available undersize bearing
mm
(in) 0.25 (0.010), 0.50 (0.020), 0.75 (0.030)
Crankpin bearing
Crankpin bearing
oil
clearance
mm
(in) Standard 0.027-0.067 (0.0011-0.0026) Crankpin bearing
oil
clearance
mm
(in) Maximum 0.10 (0.0039)
Available undersize bearina
mm
(in) 0.25 (0.010), 0.50 (0.020), 0.75 (0.030)
Thrust bearing (center main bearing)
Crankshaft end play
mm
(in) Standard 0.08-0.18 (0.0031-0.0071) Crankshaft end play
mm
(in) Maximum 0.30 (0.0118)
Bearing width
mm
(in)
Standard 27.94-27.99 (1.100-1.102)
Bearing width
mm
(in) 0.25 (0.010) oversize 28.04—28.09 (1.104-1.106) Bearing width
mm
(in) 0.50 (0.020) oversize 28.12—28.17 (1.107-1.109) Bearing width
mm
(in)
0.75 (0.030) oversize 28.20-28.25 (1.110-1.112)
Timing belt
Belt deflection
mm
(in)/98
N
(10 kg,
22 lb)
7.5-8.5 (0.30-0.33)
30—10
Page 1826 of 1865
30 TECHNICAL DATA
—— Engine model Item RF-CX RF-N
0..t cy sui.aro
mm
(in) 1.6 (0.063)/2° max.
Setting load/height
N
(kg. Ib)/mm (in) 275 (28.0, 62)/39.0 (1.535)
Tappet
Tappet outer diameter
mm
(in) 34.95-34.97 (1.3764-1.3768)
Tappet hole diameter
mm
(in) 34.99-35.01 (1.3776-1.3787)
Tappet
to
tappet hole
,. ,
clearance
mm (in)
Standard 0.02-0.06 (0.0008-0.0024) Tappet
to
tappet hole
,. ,
clearance
mm (in)
Maximum 0.10 (0.004)
Camshaft and camshaft caps
Cam lobe height
mm (in)
IN Standard 42.521 (1.6741) 44.306 (1.7443)
Cam lobe height
mm (in)
IN Minimum 42.11 (1.658) 43.90 (1.728) Cam lobe height
mm (in)
EX Standard 45.300 (1.7835) Cam lobe height
mm (in)
EX Minimum 44.90 (1.768)
Journal diameter
mm (in)
Standard 31.959-31.975 (1.2582-1.2589) Journal diameter
mm (in)
Out-of-round 0.05 (0.0020) max.
Camshaft bearing
oil
clearance
mm (in)
Standard 0.025—0.066 (0.0010-0.0026) Camshaft bearing
oil
clearance
mm (in) Maximum 0.10 (0.004)
Camshaft run-out (deflection)
mm
(in) 0.10 (0.004) max.
Camshaft end play
mm (in)
Standard 0.02-0.15 (0.0008-0.0059) Camshaft end play
mm (in)
Maximum 0.20 (0.008)
Cylinder block
Height
mm (in)
301.5 (11.87)
Distortion
mm (in)
0.10 (0.004) max.
Cylinder bore diameter
mm (in)
Standard size 86.000-86.022 (3.3858-3.3867) Cylinder bore diameter
mm (in) 0.25 (0.010) oversize 86.250-86.272 (3.3957-3.3965) Cylinder bore diameter
mm (in) 0.50 (0.020) oversize 86.500-86.522 (3.4055-3.4064)
Cylinder bore taper and out-of-round
mm
(in) 0.022 (0.0009) max.
Piston
Piston diameter (Measured at 90°
to pin
bore axis and
19
mm (0.75
in)
above the bottom
of
pis-ton) mm (in)
Standard size 85.957—85.983 (3.3841—3.3852) Piston diameter (Measured at 90°
to pin
bore axis and
19
mm (0.75
in)
above the bottom
of
pis-ton) mm (in)
0.25 (0.010) oversize 86.207-86.233 (3.3940-3.3950)
Piston diameter (Measured at 90°
to pin
bore axis and
19
mm (0.75
in)
above the bottom
of
pis-ton) mm (in) 0.50 (0.020) oversize 86.457-86.483 (3.4038-3.4048)
Piston and cylinder clearance
mm
(in) Standard 0.032-0.050 (0.0013-0.0020) Piston and cylinder clearance
mm
(in) Maximum 0.15 (0.0059)
Piston ring
Thickness
mm
(in)
TOD
1.97-1.99 (0.0776-0.0783) Thickness
mm
(in) Second 1.97-1.99 (0.0776—0.0783)
End gap (measured
in
the cylinder)
mm (in)
TOD
0.20-0.35 (0.008-0.014) 0.20-0.40 (0.008-0.016)
End gap (measured
in
the cylinder)
mm (in)
Second 0.20-0.35 (0.008-0.014) 0.20-0.40 (0.008-0.016) End gap (measured
in
the cylinder)
mm (in) Oil (rail) 0.20-0.40 (0.008-0.016)
End gap (measured
in
the cylinder)
mm (in)
Maximum 1.0 (0.039)
Ring groove width
in
piston
mm
(in)
TOD
2.17-2.19 (0.0854-0.0862) 2.04-2.06 (0.0803-0.0811)
Ring groove width
in
piston
mm
(in) Second 2.03-2.05 (0.0799—0.0807) Ring groove width
in
piston
mm
(in)
Oil 4.02-4.04 (0.1583-0.1591)
Clearance
of
piston ring
to
ring groove
mm (in)
TOD
0.18-0.22 (0.0071-0.0087) 0.05—0.09 (0.0020-0.0035) Clearance
of
piston ring
to
ring groove
mm (in) Second 0.04-0.08 (0.0016-0.0031) Clearance
of
piston ring
to
ring groove
mm (in) Maximum 0.2 (0.008)
Piston pin
Piston pin hole diameter
(in
piston) 29.997-30.007 (1.1810-1.1814) 24.997-25.007 (0.9841-0.9845)
Diameter
mm
fin) 29.994-30.000 (1.1809-1.1811) 24.994-25.000 (0.9840-0.9843)
Clearance
in
connecting rod bushing
mm
(in) 0.05 (0.002) max.
30—12
Page 1835 of 1865
TECHNICAL DATA 30
4C. FUEL AND EMISSION CONTROL SYSTEM (FE DOHC)
Item ^Engine^model Unleaded fuel Leaded fuel
Idle speed rpm With test connector grounded 750
± 50
Throttle body
Type Horizotal draft (2-barrel)
Throat diameter mm (in) No.1 46 (1.8) Throat diameter mm (in) No.
2
40 (1.6)
Fuel pump
Type Impeller (in tank)
Output pressure kPa (kg/cm2,
psi)
Main pump: 441—588 (4.5—6.0, 64—85)
Transfer pump: 20—25 (0.20—0.25, 2.8—3.6)
Feeding capacity cc (cu in)/10 seconds Main pump: 220 (13.4) min. Transfer pump: 190 (11.6) min.
Fuel filter
Type Low-pressure side Nylon element Type High-pressure side Paper element
Pressure regulator
Type Diaphragm
Regulating pressure kPa (kg/cm2, psi) 235-275 (2.4 -2.8, 34-40)
Injector
Type High-ohmic
Type
of
drive Voltage
Resistance
ft
12--16
Injection amount cc (cu in)/15 seconds 66-91 (4.03-5.55)
Idle speed control valve
Solenoid resistance Q 6.3--9.9
Fuel tank
Capacity liters (US gal, Imp gal) 60 (15.9, 13.2) 57 (15.0, 12.5): 4-wheel steering vehicle
Air cleaner
Element type Dry
Fuel
Specification Unleaded (95 RON
or
more) i Leaded (95 RON
or
more)
30-21
Page 1840 of 1865
30 TECHNICAL DATA
7A. MANUAL TRANSAXLE
Engine model FE DOHC Ffl FE FE
B
valve F8 Item —— Leaded UriBsded Ffl 12 valve Carb. Fl F8 RF-N RF-CX
Transmission
Shift
lever
position Floor shift
Gear ratio
First 3.307
Second 1.833
Third 1.310
Fourth 1.030
Fifth 0.837
1,233
0.970
0.795
0.914
1.161
0.861
0.755 0.680
Reverse 3.166
Oil capacity liters US qt, Imp
qt)
3.35 (3.6, 3.0)
Fluid type
ATF: DEXRON-II
Above 0°F: API GL-4
or
GL-5
SAE80W—90
or
SAE90
Clearance
Clearance
of
lever and reverse idle
gear
mm (in)
Standard 0.1—0.32 (0.004-0.013) Clearance
of
lever and reverse idle
gear
mm (in)
Wear limit 0.5 (0.020)
Clearance
of
shift fork and clutch hub sleeve
mm (in)
Standard 0.2—0.4 (0.008-0.016) Clearance
of
shift fork and clutch hub sleeve
mm (in)
Wear limit 0.5 (0.020)
Clearance
of
synchronizer ring
and
gear
mm
(in)
Standard 1.5 (0.059) Clearance
of
synchronizer ring
and
gear
mm
(in) Wear limit 0.8 (0.021)
Gear thrust clearance
mm (in)
First Standard 0.05—0.28 (0.002-0.011)
Gear thrust clearance
mm (in)
First Limit 0.3 (0.020)
Gear thrust clearance
mm (in)
Second Standard 0.18—0.46 (0.007-0.018)
Gear thrust clearance
mm (in)
Second Limit 0.5 (0.02) Gear thrust clearance
mm (in) Third Standard 0.05-0.20 (0.002-0.008)
Gear thrust clearance
mm (in) Third Limit 0.25 (0.010)
Gear thrust clearance
mm (in)
Fourth Standard 0.17—0.37 (0.0064—0.014)
Gear thrust clearance
mm (in)
Fourth Limit 0.4 (0.016)
Bearing preload
of
primary shaft gear
Primary shaft
0.1-0.25 N-m (1.0-2.5 cm-kg, 0.86-2.18 in-lb) Secondary shaft 0.2-0.4 N-m (2.0—4.0 cm-kg, 1.7-3.4 in-lb)
Bearing preload adjust shim mm (in) 0.25 (0.010), 0.30 (0.012), 0.35 (0.014), 0.40 (0.016), 0.45 (0.018), 0.50 (0.020), 0.55 (0.022), 0.60 (0.024), 0.65 (0.026), 0.70 (0.028), 0.75 (0.030), 0.80 (0.031)
Drive and differential
Final gear
TvDe
Reduction ratio
Side
bearina Dreload
Helical aear
4.1051 3.850 4.1051 3.850
4.150
1.4-2.0 N
m
(14—20 cm-kg, 12-17 in-lb)
Bearing preload adjust shim mm (in)
0.10 (0.004), 0.15 (0.006), 0.20 (0.008), 0.25 (0.010), 0.30 (0.012), 0.35 (0.014), 0.40 (0.016), 0.45 (0.018), 0.50 (0.020), 0.55 (0.022), 0.60 (0.024), 0.65 (0.026), 0.70 (0.028), 0.75 (0.030), 0.80 (0.031), 0.85 (0.033), 0.90 (0.035), 0.95 (0.037), 1.00 (0.039), 1.05 (0.041), 1.10 (0.043), 1.15 (0.045), 1.20 (0.047)
Backlash
of
side aear and
Dinion
aear mm (in) 0-0.1 (0-0.004)
30—26