1987 MAZDA 626 lock

FRONT AXLE 9
REMOVAL
Removal in the sequence shown in the figure referring to the removal note for the specially marked parts.
1. Hub cap
2. Lock nut
3. Caliper assembly
4. Disc plate
5. Tie-rod end
6. Stabilizer
7. Lower arm
8. Wheel speed sensor (ABS)
9. Knuckle
86U09X-009
Removal Note
Lock nut
1. Uncrimp the tab of the lock nut.
86U09X-010
9—9

FRONT AXLE 9
86U09X-023
86U09X-024
86U09X-025
4. Install the stabilizer.
Dimension: 20.1 mm (0.79 in)
Tightening torque: 16—23 N-m
(1.6—2.3 m-kg, 12—17 ft-lb)
5. Install the wheel speed sensor. (ABS)
Tightening torque: 16—23 N-m
(1.6—2.3 m-kg, 12—17 ft-lb)
6. Install the tie-rod end.
Tightening torque: 29—44 N-m
(3.0—4.5 m-kg, 22—33 ft-lb)
86U09X-026
7. Check the end play. (Refer to page 9—8)
End play: 0.2 mm (0.0079 in) max.
8. Stake the lock nut to groove.
9. Install the caliper assembly.
Tightening torque: 78—98 N-m
(8.0—10.0 m-kg, 58—72 ft-lb)
10. Install the wheel.
Tightening torque: 88—118 N-m
(9.0—12.0 m-kg, 65—87 ft-lb)
9-15

REAR AXLE 9
[Drum Brake]
REMOVAL
Remove in the sequence shown in the figure referring to the removal note for the specially marked parts.
86U09X-030
1. Hub cap
2. Lock nut
3. Brake drum
4. Parking brake cable
5. Brake pipe
6. Back plate
7. Trailing link
8. Lateral link
9. Shock absorber
10. Knuckle spindle
11. Brake shoe assembly
Removal Note
Disconnect the brake pipe with the SST.
86U09X-03 I
9—17

REAR AXLE 9
[Disc Brake]
REMOVAL (2WS)
Remove in the sequence shown in the figure.
1. Hub cap
2. Lock nut
3. Caliper assembly
4. Disc plate
5. Wheel speed sensor (ABS)
6. Dust cover
7. Trailing link
8. Lateral link
9. Shock absorber
10. Knuckle spindle
86U09X-039
9-21

REAR AXLE
REMOVAL (4WS)
Remove in the sequence shown in the figure referring to the removal note for the specially marked parts.
86U09X-040
1. Hub cap 7. Control link
2. Lock nut 8. Wheel speed sensor (ABS)
3. Parking brake cable 9. Stabilizer bracket
4. Caliper assembly 10. Tie-rod end
5. Disc plate 11. Shock absorber
6. Dust cover 12. Knuckle spindle
Removal Note
Tie-rod end
Remove the tie-rod end from the knuckle spindle with
the SST.
86U09X-041
9-22

DRIVESHAFT 9
REMOVAL
Remove in the sequence shown in the figure referring to the removal note for the specially marked parts.
0
B6U09X-U53
6. Hub cap
7. Lock nut
8. Driveshaft
9. Joint shaft
10. Transaxle
Removal Note
Lock nut
Applying the brakes. Raise the lock nut tab and loos-
en it. Do not remove it.
1. Wheel
2. Tie-rod end
3. Stabilizer
4. Lower arm
5. Splash shield
86U09X-054
9-29

9 DRIVESHAFT
Boot Band
Tighten the boot band.
Note a) Use a new band.
b) Fold the band in the direction opposite the
forward rotation of the driveshaft.
1. Fold the band back by pulling on the end of the
band.
86U09X-096
2. Bend the locking clip to lock the end of the band.
86U09X-097
9—34

9 DRIVESHAFT
Front wheel hub
After installation, pull the front wheel hub outward and
check that the driveshaft does not come out.
86U09X-072
Stabilizer
Lock the nut with 20.1 mm (0.79 in) of the threads
exposed.
Tightening torque: 16—23 N-m
(1.6—2.3 m-kg, 12—17 ft-lb)
76G09X-004
9—38