1987 MAZDA 626 fuel filter

TROUBLESHOOTING GUIDE 4A
FE (MIDDLE EAST)
The Troubleshooting Guide lists the systems most likely to cause a given symptom. After finding the
system(s) to check, refer to pages shown for detailed guides for each system.
V. POSSIBLE CAUSE
\ PAGE
SYMPTOM

I
Air

cleaner

(Air

cleaner

element)

Intake

air

temperature

control

system

Idle

adjustment

Fuel

system

(Carburetor,

Fuel

pump)

Idle-up

control

system
Dashpot

(Only

MTX)

Positive

crankcase

ventilation

system
Exhaust
system

Evaporative

emission

control

system

Auto-return

choke

system

V. POSSIBLE CAUSE
\ PAGE
SYMPTOM 4A—23 4A-60 4 A—38 4A-24 4A-68 4A-50 4A-67 4A-96 4A-78 4A-40
1 Hard start or won't start
(Cranks OK) 1 2 3
2 Engine stalls During warm up 3 2 1 4 2 Engine stalls After warm up 3 2 4 1
3 Rough idle During warm up 3 2 1 4 3 Rough idle After warm up 3 2 4 1
4 High idle speed after warm up 1 5 3 4 2
5 Poor acceleration, hesitation, or lack of power 1 2 3
6 Runs rough on deceleration 2 1
7 Afterburn in exhaust system 3 1 2
8 Poor fuel consumption 5 1 6 2 3 4
9 Falls emission test 5 4 6 3 1 2
76G04A-019
The numbers of the list show the priorities of inspections from the most possible to that with the lowest
possibility.
These were determined on the following basis:
• Ease of inspection • Most possible system • Most possible point in system
TROUBLESHOOTING PROCEDURE:
1st Check the following items:
Electrical system
1) Battery condition
2) Fuses
Ignition system
1) Spark plugs
2) Ignition timing
Fuel system
1) Fuel level
2) Fuel leakage
3) Fuel filter
4) Idle speed
Intake air system
1) Vacuum or air leakage
2) Vacuum hose routing
3) Accelerator cable
4) Choke cable
Engine
1) Compression
2) Overheating
Others
1) Clutch slippage
2) Brake dragging
2nd Check the Fuel and Emission Control Systems
4 A—21

4A TROUBLESHOOTING GUIDE
FE 8VALVE—UNLEADED FUEL
The Troubleshooting Guide lists the systems most likely to cause a given symptom. After finding the
system(s) to check, refer to the pages shown for detailed guides for each system.
V POSSIBLE CAUSE
\ PAGE
SYMPTOM
Air

cleaner

(Air

cleaner

element)

Idle

adjustment

Fuel

system
(Carburetor,

Fuel

pump)
PTC

heater

system

Air

injection
system

Positive

crankcase

ventilation

system

Deceleration

control
system
Exhaust
gas

recirculation

(EGR)
system

Exhaust

system
Intake
air

temperature

control
system

Idle-up

control

system
Purge

control

system
Auto-return
choke
system
V POSSIBLE CAUSE
\ PAGE
SYMPTOM 4A-23 4A-38 4A-24 4A—42 4A-58 4A—67 4A—45 4A-96 4A-97 4A—60 4A—68 4A--63 4A—40
1 Hard start or won't start
(Cranks OK) 1 2
2 Engine stalls During warm up 6 1 2 5 3 4 2 Engine stalls After warm up 4 2 3 1
3 Rough Idle During warm up 5 1 2 4 3 6 3 Rough Idle After warm up 4 2 3 1
4 High idle speed after warm up 1 5 4 3 2
5 Poor acceleration, hesitation, or lack of power 1 2 5 3 4
6 Runs rough on deceleratio 2 1
7 Afterburn in exhaust system 2 1
8 Poor fuel consumption 4 1 2 3 5
9 Fails emission test 5 1 6 4 3 2
76G04A-020
The numbers of the list show the priorities of inspections from the most possible to that with the lowest
possibility.
These were determined on the following basis:
• Ease of inspection • Most possible system • Most possible point in system
TROUBLESHOOTING PROCEDURE:
1st Check the following items:
Electrical system
1) Battery condition
2) Fuses
Intake air system
1) Vacuum or air leakage
2) Vacuum hose routing
3) Accelerator cable
4) Choke cable
2nd Check the Fuel and Emission Control Systems
Ignition system
1) Spark plugs
2) Ignition timing
Engine
1) Compression
2) Overheating
Fuel system
1) Fuel level
2) Fuel leakage
3) Fuel filter
4) Idle speed
Others
1) Clutch slippage
2) Brake dragging
4A-22

4A FUEL SYSTEM
FUEL SYSTEM
This system consists of the fuel pump, fuel filters, and carburetor, and supplies the necessary fuel for
operation of the engine.
76G04A-025
4A—24

FUEL SYSTEM 4A
SEPARATOR
Inspection
Visually check the separator for fuel leakage and dam-
age. Replace, if necessary.
76G04A-055
TWO-WAY CHECK VALVE
(Except Middle East)
Inspection
1. Disconnect the hoses, and remove the check
valve.
2. Check that air flows in both directions through the
valve.
3. If not as specified, replace the two-way check
valve.
76G04A-056
THREE-WAY CHECK VALVE
(Middle East)
1. Blow through the valve from port and check
that air comes out of port (§).
Next, block port ©and check that air comes of
port ©.
2. Block port ©and apply vacuum with a vacuum
pump through port
3. Check that no vacuum is held.
76G04A-057
FUEL FILTER
Replacement
The fuel filter is mounted on the left side of the frame.
Caution
a) To prevent gasoline from draining during
removal, first disconnect and plug the in-
let hose.
b) During installation be sure to install the fuel
filter in the correct direction of flow.
76G04A-058
4 A—37

4B OUTLINE
SPECIFICATIONS
Item Specification

Idle speed rpm MTX: 800 +5„° (Neutral), ATX: 900 +5S
(P
range)

Throttle body

Type Horizontal draft (1 -barrel)
Throat diameter mm (in) 50 (2.0)

Air flow meter

E2-VS More than
20

E2-VC 100-300
Resistor
Q
E2-VB 200—400 Resistor
Q

E2-THA -20°C
(
—4°F) 13,600-18,400 20°C
(
68°F) 2,210-2,690 60°C (140°F)
493- 667
Air cleaner

Element type Oil permeated

Fuel pump

Type Impeller
(in
tank)
Output pressure kPa (kg/cm2,
psi)
441-588 (4.5-6.0, 64—85)
Feeding capacity cc (cu in)/10 sec. 220 (13.4) minmum

Fuel filter

Type Low pressure side Nylon element Type High pressure side Paper element

Pressure regulator

Type Diaphragm
Regulating pressure kPa (kg/cm2,
psi)
235-275 (2.4—2.8, 34—40)

Injector
TvDe
Hiqh-ohmic
Type
of
drive Voltage
Resistance
fi
12-16
Injection amount cc (cu
in) 15
seconds 38—53 (2.3-3.2)

Fuel tank

Capacity liters (US gal, Imp gal) 60 (15.9, 13.2)

Fuel

Soecification Unleaded reaular

76G04B-506
4B—6

TROUBLESHOOTING GUIDE 4B
TROUBLESHOOTING GUIDE
This troubleshooting guide shows the malfunction numbers and the symptoms of various failures.
Perform troubleshooting as described below.
Possible cause
Symptom
Input sensors and switches
o> Q.
C
0
Jh c 01
4B-14
a> 4)
E
o
4B-1S
o in c « m o E k_ 0) c.
0 <0 £
4B-16
o CO c a> 0) o E
a>
.x
co
4B-17
o 10 c a) co
4B-18
o in c a> (0
o> o> a>
a) £ a VI o E
4B-19
0 <0 c a> 0) c a> 01
S? o
4B-20
E a> in (0
o 10 A •o 0) 0> u.
4B-21
Output solenoid valves
o «
3 O) 0)
0) 0) 01
0> > 10 >
•o o c V o tt)
4B-22
0)
OI

0> > CO >

TJ
O c 0> o CO
4B-23
oc O u
o> > 75 >
•o o c a> o 05
4B-23
0 a. 3 1
2
0) > (0 >
"D O
o 0> in in a a >. £
4B-23
ffl a 3 • a>
2
a> > 10 >
"O o c a> o
CO Q. >. JO
4B-24
Fault Indicated by SST
Code No. 01 08 09 10 12 14 15 17 25 26 28 34 35
Hard start or won't start
(Cranks OK)
Engine stalls
Rough
idle
While warming up
After warming up
While warming up
After warming up
High idle speed after
warming up
TROUBLESHOOTING PROCEDURE
Note
Step 1 under symptom is to quickly determine what system or unit may be at fault by use of the SST. (Self-Diagnosis Checker 49 H018 9A1)
1st:
Check input sensors and output solenoid valves with the
SST.
(Refer
to
page 4B—10.)

2nd:
Check other switches with the
SST.
(Refer
to
page 4B—26.)

3rd:
Check the following items:

11
Poor acceleration, hesita-
tion or lack of power
Runs rough on deceleration
Afterburn in exhaust system
Poor fuel consumption
Engine stalls or rough after hot starting
Electrical system
1) Battery condition
2) Fuses

Fuel system
1) Fuel level 2) Fuel leakage
3) Fuel filter 4) Idle speed

Engine
1) Compression 2) Overheating

Ignition system

1) Ignition spark 2) Ignition timing

Intake air system
1)
Air
cleaner element 2) Vacuum
or air
leakage 3) Vacuum hose routing
4) Accelerator cable

Others
1) Clutch slippage 2) Brake dragging

Fails emission test 4th:
Check Fuel and Emission Control Systems. (Refer
to
page 4B—8.)

76G04B-003
4B—7

4B INTAKE AIR SYSTEM
INTAKE AIR SYSTEM
76G04B-036
This system controls the air required by the engine for operation. The system consists of the air duct,
air cleaner, air flow meter, throttle body, dynamic chamber, and intake manifold.
COMPONENT DESCRIPTIONS
Component Function Remarks
Air cleaner
Filters
air
into throttle body

Air flow meter
Detects amount
of
intake air;
sends signal
to
engine control unit Intake
air
thermo sensor and fuel pump
switch are integrated

Throttle body
Controls intake
air
quantity Integrated throttle sensor and idle switch

76G04B-037
4B—30

4B FUEL SYSTEM
FUEL SYSTEM
76G04B-057
This system supplies the fuel necessary for combustion at a constant pressure to the injectors. Fuel
is metered and injected into the intake manifold according to the injection control signals from the en-
gine control unit. It consists of the fuel pump, fuel filters, delivery pipe, pulsation damper, pressure
regulator, injectors, fuel pump switch (incorporated in the air flow meter), and the circuit opening relay.
The fuel pump is mounted in the fuel tank to minimize the operating noise of the fuel pump. The injec-
tors are directly supplied with battery voltage through the main relay.
4B—42