1987 MAZDA 626 Rear brake

4B CONTROL SYSTEM
Terminal Voltage
If the input and output devices and related wiring are normal, but the engine control unit terminal volt-
age is incorrect, replace the engine control unit.
Terminal Input Output Connection to Voltage (After warming-up) Remarks Terminal Input Output Connection to IGN: ON Idle Remarks
1A — — — — —
1B o Self-Diagnosis Checker (Code number)
For 3sec. after ignition switch OFF ->• ON: below 6.2V (Buzzer sounds) After 3sec.: Battery voltage (Buzzer does not sound)
• Using Self-Diagnosis Check-er and test con-nector grounded • Buzzer sounds: below 6.2V • Buzzer does not sound: Battery voltage
1C — — — — —
1D o Self-Diagnosis Checker (Monitor lamp)
Test connector grounded
For 3sec. after igni-tion switch OFF ON:
below 6.2V (light il-luminates) After 3sec.: Battery voltage (light does not illuminate)
(Test connector grounded) approx. 10V (Test connector not grounded) Monitor lamp ON: below 6.2V Monitor lamp OFF: Battery voltage
With Self-Diagnosis
Checker
1E O Idle switch Accelerator pedal released: below 1.5V
Accelerator pedal depressed: Battery voltage
1F o A/C relay A/C switch ON: below 2.5V A/C switch OFF: Battery voltage
Blower motor ON
1G — — — — —
1H o Water thermo switch Below 1,5V Radiator temp.:
above 17°C (63°F)
11 o Electrical load con-trol unit Electrical load ON: below 1.5V Electrical load OFF: Battery voltage Electrical load: Rear defroster Headlight Blower motor (3rd & 4th position) Electrical fan
1J o Brake light switch Brake pedal released: below 1.5V
Brake pedal depressed: battery voltage
1K — — — — — —
1L o A/C switch A/C switch ON: below 1.5V
A/C switch OFF: battery voltage
Blower motor: ON
1M o Ignition coil © terminal Battery voltage *1 Battery voltage *1 Engine Signal Monitor: green and red lights flash
1N — — — — —
10 — — — —
4B-88

4C TROUBLESHOOTING WITH SST
Check connector: (Green, 6 pin)
49 H018 9A1
86U04A-011
Test connector: (Green, 1 pin)'
INSPECTION PROCEDURE
1. Connect the SST to the check connector. (Green,
6-pin) and the negative battery terminal.
2. Set the select switch to position A.
Note
The check connector is located at the rear of
the left side wheel housing.
3. Ground the test connector (Green, 1-pin) with a
jumper wire.
Note
The test connector is located near the Self-
Diagnosis Checker check connector.
86U04A-012
OO
uu
SELF-DIAGNOSIS CHECKER
MONITOR LAMP SELECT SW «

o o o
o
76G04C-012
4. Turn the ignition switch ON.
5. Verify that 88 flashes on the digital display and that
the buzzer sounds for three seconds after turn-
ing the ignition switch ON.
6. If 88 does not flash, check the control relay (refer
to page 4C—96), power supply circuit, and check
connector wiring.
7. If 88 flashes and the buzzer sounds continuously
for more than 20 seconds check the check con-
nector wiring, then replace the engine control unit
and perform steps 3 and 4 again.
8. Note the code numbers and check for the causes
by referring to the check sequences shown on
pages 4C—16 to 4C—24. Repair as necessary.
Note
Cancel the code numbers by performing the
after-repair procedure after repairing.
AFTER-REPAIR PROCEDURE
1. Cancel the memory of malfunctions by disconnect-
ing the negative battery cable and depress the
brake pedal for at least five seconds.
76G04C-013
4C-12

TROUBLESHOOTING (G4A-EL) 7B
STEP 4 (STALL TEST)
This step is performed to determine if there is slippage of the friction elements or malfunction of the
hydraulic components.
Preparation
Check the following items prior to testing:
1. Engine coolant, engine oil and ATF levels.
2. Warm the engine thoroughly to raise the ATF temperature to operating level (50—80°C, 122—176°F).
3. Engage the parking brake and use wheel chocks at the front and rear wheels.
Pull the parking brake Water temperature
ATF
79G07C-084
7B-27

TROUBLESHOOTING (G4A-HL) 7B
STEP 3 (STALL TEST)
This step is performed to determine if there is slippage of the friction elements or malfunction of the
hydraulic components.
Preparation
Check the following items prior to testing:
1. Engine coolant, engine oil and ATF levels.
2. Warm the engine thoroughly to raise the ATF temperature to operating level (50—80°C, 122—176°F).
3. Engage the parking brake and use wheel chocks at the front and rear wheels.
Pull the parking brake Water temperature
ATF
83U07B-038
7B—49

7B INSPECTION AND REPAIR
CONTROL VALVE BODY (G4A-EL)
Precaution
(1) Pay close attention when handling the control valve because it consists of the most precise and
delicate parts of the transaxle.
(2) Neatly arrange the removed parts in order to avoid mixing up similar parts.
(3) Disassemble the control valve assembly and thoroughly clean it when the clutch and/or brake bands
are burned, and/or when the automatic transaxle fluid is degenerated.
Components I
Front and premain control body
6—8 N-m (66—80 cm-kg, 57—69 in-lb)
1.1-2 Solenoid valve
2. 2-3 Solenoid valve
3. Bolts
4. Front control body
5. Front/premain front gasket
6. Premain separator
7. Front/premain rear gasket
8. Premain control body
9. Premain/main front gasket
10. Main separator
76G07B-141
7B—136

INSPECTION AND REPAIR 7B
CONTROL VALVE BODY (G4A-HL)
Precaution
(1) Pay close attention when handling the control valve because it consists df the most precise and
delicate parts of the transaxle.
(2) Neatly arrange the removed parts in order to avoid mixing up similar parts.
(3) Disassemble the control valve assembly and thoroughly clean it when the clutch and/or brake bands
are burned, and/or when the automatic transaxle fluid is degenerated.
Components I
Front and premain control body
6—8 Nm ® (66—80 cm-kg, 57—69 In-lb)
1. Lock-up solenoid valve
2. Front control body
3. Front/premain front gasket
4. Premain separator
5. Front/premain rear gasket
6. Premain control body
7. Premain/main front gasket
8. Main separator
76G07B-163
7B—155

7C
AUTOMATIC TRANSAXLE
(3-Speed)
OUTLINE 7C— 2
SPECIFICATIONS 7C— 2
CROSS-SECTIONAL VIEW 7C— 3
OPERATION OF COMPONENTS . 7C— 4
FLUID PASSAGE LOCATION 7C— 5
TROUBLESHOOTING 7C— 8
GENERAL NOTE 7C— 8
QUICK DIAGNOSIS CHART 7C— 9
STEP 1
(PRELIMINARY INSPECTION).... 7C— 12
STEP 2 (STALL TEST) 7C— 14
STEP 3 (TIME LAG TEST) 7C— 17
STEP 4 (ROAD TEST) 7C— 18
STEP 5 (OIL PRESSURE TEST)... 7C— 20
ELECTRIC COMPONENTS 7C— 23
INHIBITOR SWITCH 7C— 23
KICK-DOWN SWITCH 7C— 23
KICK-DOWN SOLENOID 7C— 24
ON-VEHICLE MAINTENANCE 7C- 25
AUTOMATIC TRANSAXLE FLUID
(ATF) 7C— 25
SELECTOR LEVER 7C— 26
VACUUM DIAPHRAGM 7C— 27
REPLACEMENT OF CONTROL
VALVE 7C— 28
REPLACEMENT OF SERVO
PISTON RETURN SPRING 7C— 29
REMOVAL 7C— 30
PREPARATION 7C— 30
DISASSEMBLY 7C— 35
DISASSEMBLY-STEP 1 7C— 35
DISASSEMBLY-STEP 2 7C— 41
DISASSEMBLY-STEP 3 7C— 45
DISASSEMBLY-STEP 4 7C— 51
INSPECTION AND REPAIR 7C- 54
PRECAUTION 7C— 54
TORQUE CONVERTER 7C— 54
OIL PUMP 7C— 55
FRONT CLUTCH 7C— 58
REAR CLUTCH 7C— 62
REAR CLUTCH HUB 7C— 65
DRUM HUB 7C— 66
ONE-WAY CLUTCH INNER RACE 7C— 68
BAND SERVO 7C— 69
BRAKE BAND 7C— 70
PLANETARY CARRIER (FRONT).. 7C— 71
ONE-WAY CLUTCH 7C— 71
LOW AND REVERSE BRAKE 7C— 71
GOVERNOR 7C— 72
CONTROL VALVE BODY 7C— 75
DIFFERENTIAL 7C— 79
OUTPUT GEAR 7C— 82
IDLE GEAR 7C— 83
BEARING COVER ASSEMBLY .... 7C— 86
BEARING HOUSING 7C— 87
SIDE BEARING HOUSING 7C— 88
ASSEMBLY 7C— 89
PRECAUTION 7C— 89
ASSEMBLY-STEP 1 7C— 89
ASSEMBLY-STEP 2 7C— 98
ASSEMBLY-STEP 3 7C—106
ASSEMBLY-STEP 4 7C—111
INSTALLATION 7C—119
TORQUE SPECIFICATIONS 7C—119
HYDRAULIC CIRCUIT 7C—125
OUTLINE 7C—125
P RANGE 7C—126
R RANGE 7C—127
N RANGE 7C—128
D RANGE (1ST GEAR) 7C—129
D RANGE (2ND GEAR) 7C—130
D RANGE (3RD GEAR) 7C—131
D RANGE (KICK-DOWN; SHIFT
VALVES IN 2ND POSITION) 7C—132
2 RANGE (2ND GEAR) 7C—133
1 RANGE (1ST GEAR) 7C—134
1 RANGE (2ND GEAR) 7C—135
76G07C-001

7C OUTLINE
OUTLINE
SPECIFICATIONS
Model F3A Model FE engine F6 engine
Torque converter stall torque ratio 1.800-2.100 : 1
Gear ratio
First 2.841
Gear ratio Second 1.541 Gear ratio
Third 1.000
Gear ratio
Reverse 2.400
Final gear ratio 3.450 : 1 3.631 : 1
Number of drive plates/ driven plates
Front clutch 3/3
Number of drive plates/ driven plates Rear clutch 4/4 Number of drive plates/ driven plates
Low and reverse brake 4/4
Servo diameter (Piston outer dia./retainer inner dia.) mm (in) 64/36 (2.52/1.42) 64/44 (2.52/1.73)
Speedometer gear ratio (Driven/Drive gear) 0.80 (20/25) 0.84 (21/25)
Automatic transaxle fluid
Type Dexron-II or M-III
Automatic transaxle fluid Capacity liters
(US qt, Imp qt) 6.2 (6.6, 5.5)
76G07C-002
7C—2