1984 NISSAN 300ZX chime

ELECTRICAL SYSTEM
I
SECTION EL
CONTENTS
HOW TO READ DIAGRAMS
STANDARDIZED RELAY
POWER SUPPLY ROUTING
BATTERY.
.. ..
STARTING SYSTEM .
STARTING SYSTEM -Starter -
CHARGING SYSTEM .
CHARGING SYSTEM - Alternator
COMB IN AT1 ON SWITCH
INSTRUMENT SWITCH
HEADLAMP
EXTERIOR LAMP,
INTERIOR LAMP
.
..
..
..
..
..
... ......
..
.. ....
..
.. ...
EL- 2
EL- 3
EL- 4
EL- 6
EL- 9
EL-
10
EL- 15
EL- 17
EL- 23
EL- 25
EL- 26
EL- 34
EL- 38
METER AND GAUGES - Digital Type Combination Meter . . EL- 41
METER AND GAUGES - Digital Type Combination Gauge . .. .. EL- 57
METER AND GAUGES - Needle Type Combination Meter .. . EL- 65
METER AND GAUGES
- Needle Type Combination Gauge.. .... EL- 68
WARNING LAMPS AND CHIME. .......... ... .... EL- 71
VOICE WARNING SYSTEM
... ... EL- 76
TIME CONTROL SYSTEM ... EL- 81
WIPER AND WASHER .... .... ... ... . EL- 89
HORN, CIGARETTE LIGHTER, CLOCK . . ......... EL- 92
REAR WINDOW DEFOGGER
... .. ... ....... EL- 93
AUDIO AND POWER ANTENNA
,. . .... .. . EL- 95
AUTOMATIC SPEED CONTROL DEVICE (AS
C D ) . ... , . EL- 97
LOCATION OF ELECTRICAL UNITS
... .. .. .. EL-104
HARNESS LAYOUT
. . .. .. .. . EL-107

WARNING LAMPS AND CHIME
I
33tlVH3
pg
I K-7 1 I
dWV1 tlV3tl
M dWVlOV3H

WARNING LAMPS AND CHIME
- Warning Lamps/Wiring Diagram- For Digital Type Combination Meter- -
SEL698D
EL-72

WARNING LAMPS AND CHIME
Warning Chime/Wiring Diagram
SEL793D
EL-74

WARNING LAMPS AND CHIME
Diode Check
Check continuity using an ohmmeter
Diode
is functioning properly if test results are
as shown below
--I+-- 11 ,- Diode
Ohmmeter
NO continuity
@
SEL700D
DIGITAL TYPE COMBINATION METER
Diodes for warning lamps are located on the
panel where warning bulbsare fitted
For bulb check
For brake warning
7f For door warning
Far door warning
For tail lamp warning
For radmtor warning
Far 0, sensor warning
Far headlamp warning For brake warning
SEL701D
-~
NEEDLE TYPE COMBINATION METER
Diodes for warning lamps are built into the
Combination meter printed circuit
7- For 0, sensor warning
BRAKE DOOR FUEL
For bulb check
LAMP
SEL70ZD
--Warning Chime Check
A
SEL875D
EL-75

TIME CONTROL SYSTEM
Trouble-shooting (Cont'd)
CHIME CIRCUIT CHECK
1
2
Turn ignition switch to "OFF"
Measure voltage across @ and @ when
driver's door
is opened and closed
Check from harness ride I
I Warning chime does not actlvate
1
I Go to "Power SUDD~V Circuit Check" 1
ignition rwltch OFF Approx 12Vwhen drlver'r stde door IS closed Voltmeter needle swings (0 - 12V) when dnver's
%,de door tr opened SEL718D Voltmeter
STEERING LOCK SWITCH CIRCUIT
CHECK
1
2
Turn ignition switch to "OFF"
Check voltage between @ and @
Check from harness side
12V when ignmon key IS ret into key cyllndei OV when tgnltlon key 16 pulled out of key cylinder Voltmeter SEL7190
lamp does not go off nor come on
I + Go to "Power Supply Circuit Check" 1 1 OK 1 NG
Check harness for T c u
power supply circuit
Check belt warning circuit
OK NG
Check warning lamp
v
Check seat belt switch circuit
OK 1 NG
Check seat belt switch.
and harness between T c u
and seat belt switch
Replace T C U ~~
BELT
WARNING CIRCUIT CHECK
1 Unfasten seat belt.
2 Measure voltage across @I and @ when
ignition switch
is "ON"
Che& from harness ride
0 -12v Joltmeter needle keeps SwlngInQ appr~x 0-12Vl for about 7 ;econdr after ngnition witch Is Voltmeter :urned ON SEL720C
SEAT BELT SWITCH CIRCUIT CHECK
1 Turn ignition switch to "OFF"
2. Unfasten driver's seat belt.
3. Check for continuity between 0 and @
4 Fasten driver's seat belt
5 Check to determine if continuity does not
exist between 0 and @
Check from harness %de
Ohmmeter
SEL7211
EL-87

LOCATION OF ELECTRICAL UNITS
LWarning chime Meter power unit (For digital
type combination
meter1
Hold relay (only for Canada
analog type
Clutch witch (For AS C D I
(For A 5 C D )
box
SEL753D
EL-I 06

,
TO TIME CON-
TROL UNIT
TO INST H LH (CHIME)
TO ENGINE
ROOM
H R H (UPHOLD RELAY)
TO ENGINE ROOM H L H IHEAO-
TO LIGHT SW TO LIGHT SW -
TO REAR
ro KEY sw
3OOM H R H A S C 0 RELAY1 To As sw (VACUUM ROOM H L H
PUMP RELAY)
(For time control system, headlamp system, AS C 0 and E F I system1