1984 NISSAN 300ZX warning

WARNING LAMPS AND CHIME
Diode Check
Check continuity using an ohmmeter
Diode
is functioning properly if test results are
as shown below
--I+-- 11 ,- Diode
Ohmmeter
NO continuity
@
SEL700D
DIGITAL TYPE COMBINATION METER
Diodes for warning lamps are located on the
panel where warning bulbsare fitted
For bulb check
For brake warning
7f For door warning
Far door warning
For tail lamp warning
For radmtor warning
Far 0, sensor warning
Far headlamp warning For brake warning
SEL701D
-~
NEEDLE TYPE COMBINATION METER
Diodes for warning lamps are built into the
Combination meter printed circuit
7- For 0, sensor warning
BRAKE DOOR FUEL
For bulb check
LAMP
SEL70ZD
--Warning Chime Check
A
SEL875D
EL-75

VOICE WARNING SYSTEM
Schematic
I 12
DOOR STEP DOOR SWITCH
VOICE
GENERATOR
BRAKE PARKING WARNING LAMP BRAKE SWITCH FUSE - 1 19
FUEL WARN- FUEL TANK ING LAMP GAUGE UNIT
20 COMBINATION
METER lD8gc1al type) SPEED SENSOR
5v 18
I
7 COMBINATION METER (Needle type1
@ Dlgltal typemeter
@ Needle type meter
1
DOOR
SPEAKER
LH
I
__r_l RADIO
SEL703D
EL-76

VOICE WARNING SYSTEM
Wiring Diagram

VOICE WARNING SYSTEM
Operational Check
Fuel level
I Condition I Voice Warning -~ ~
Item
Fuel level less than
1OP (2-5/8USgal, - “Fuel level is low’’
2-1/4 Imp gal) ~~
Left
door
Door switch L H is “ON“
(Left door is open)
ignition switch
“OFF” Light
Door switch L H is
”ON”
(Left door is open)
Lighting switch is “ON” “Lights are ON”
“Left door is open”
Speed switch is “ON”
Vehicle speed is more
than
10 km/h (6 MPH)
Door switch R H is
”Right door is open”
Parking brake switch Parking brake is “ON” ”Parking brake is ON”
e If rhe warning is not properly given under the above condition, go to “Trouble-Shooting”.
EL-78

VOICE WARNING SYSTEM
Trou ble-shooting
Voltmeter
Condition
1 Ignition sw "ACC"
Check if speaker in driver's door
produces sound wheri radio
is
turned "ON"
Ignition sw "OFF"
Normal
i
Check harness connector run-
ning to driver's door speaker
Lighting switch "ON"
Check voice warning switch
CNG>
More than 9V
Replace voice warning switch i
v
Disconnect connector running to voice warning device and check voltage
at each terminal of connector
I- I I
I OK T
Replace voice warning device
I NG i
Check harness
EL-79

rn I-
0
do
Left door Right door Parking brake Fuel level Light
OK (7) Check if step lamp
left or right door
is opened
Check door switch
I
I
lxeed % Sensor
Signal Check"
-1 (Refer to "METER I
Check if fuel
warning lamp
comes on when Check if parking
brake warning
lamp comes on
when parking
brake lever
is
pulled with
ignition switch
"ON"
NG
Check parking
brake switch Check fuel tank
gauge unit
(Refer to "METER
AND GAUGES")
Repair or
replace
AND GAUGES" )
v
Check for loose connector,
poor grounding
or broken wire
'""I
Repair or
replace
OK
Replace voice warning device
Check if all illumi-
nation lamps come
on when lighting
switch
is "ON"
Check lighting
switch

TIME CONTROL SYSTEM
CAUTION
Never touch the terminals of time control unit with bare hands.
1) Intermittent wiper control timer 5) Light warning timer
2) Interior lamp timer 6) Key warning timer
3) Door key hole illumination timer 7) Seat belt warning timer
4) Illumination control timer 8) Rear defogger timer
Time control unit has the following functions
ltNlTlON SWlTCH IGNITION lGNlTlON
FUSE
TlME CONTROLUNil /I
1
SEL705D
EL-81

TIME CONTROL SYSTEM
Trouble-shooting (Cont'd)
(Interior lamp will not illuminate when outside door
handle
on driver's side IS pulled 1 I
Interior lamp and step lamps do not fade out after
all doors are closed
Check if door warning lamp goes off after all doors
are closed Check if interior lamp fades out after all doors
are closed
OK NG Check door switch
Go to "Interior lamp
circuit check" Go to "Power Supply Circuit Check"
OK NG
Check harness between
T C U and interior lamp
v
Check door handle switch circuit check
OK NG
Check door handle switch
Replace T C U Check harness between T c u
and door handle switch
NG
Check harness between
T C U and interior lamp
1
INTERIOR LAMP CIRCUIT CHECK
1 Turn Ignition switch to "OFF"
2 Measure voltage across @ and @
Check from harness ride
0 V when door 15 open 0- 12 V when
door IS closed after once opened
SEL7lZO
DOOR HANDLE SWITCH CIRCUIT
CHECK
1
2
3
Turn ignition switch to "OFF"
Pull outside door handle (driver's side)
Check continuity between @ and @
Check from harness sade
I OR
ye?! door handle (driver's rude)
SEL713D ohmmeter
EL-85