1984 NISSAN 300ZX fuel type

METER AND GAUGES - Digital Type Combination Meter
Trouble-st
Torque meter does not operate
1 Go to "Display Check" I
Go to "Power Unit Check"
v
Replace meter Replace
and gauge assembly power unit
I
I Check boost sensor circuit I
boost sensor and meter boost
sensor
1 Disconnect meter harness connector
2 Connect vacuum pump gauge to boost
3
4
(white)
sensor vacuum hose
Turn the ignition switch to "ON"
Apply vacuum pressure to boost sensor by
vacuum pump gauge and measure voltage
across
0 and
Vacuum -
~eep harness connected
J wu 1 3v at-53 3kPa 1-400 mmH
SEL667 Voltmeter -15 75 mHg) '
rg (Cont'd)
Main fuel gauge does not operate
I
Go to "Display Check"
Go to "Power Unit Check"
Replace meter Replace
and gauge power unit
assembly
Check fuel tank main gauge clrcult
I OK
Replace meter
and gauge
assembly Go to "Fuel tank
gauge check"
.
Check harness between Replace fuel
fuel tank gauge and meter
tank gauge unit
1 Disconnect meter harness Connector
(black)
Turn ignition switch to
"OFF" 2
3 Measure resistance between @ and @
e

Ohmmeter SEL6680
EL-49

METER AND GAUGES - Digital Type Combination Meter
Trouble-shooting (Cont'd)
Fuel residue
Sub fuel gauge (digital display1 does not operate
Go to "Display Check"
Go to "Power Unit Check"
Replace meter Replace
and gauge power unit
assembly
Resistance
Check harness
Check fuel tank sub gauge circuit
Go to "Fuel Tank
Gauge Check"
OK
v T
Replace Check harness between Replace meter
fuel tank fuel tank gauge and meter and gauge
gauge unit assembly
FUEL INJECTION PULSE CIRCUIT
CHECK
1 Disconnect meter harness connector
(black)
2. Turn ignition switch to "ON"
3 Check for voltage across @$ and 0.
Voimeter SE L669 t
FUEL TANK SUB GAUGE CIRCUIT
CHECK
1 Turn ignition switch to "OFF"
2. Measure resistance between 0 and 0.
Ohmmeter
Ignition switch- OFF
More than ZOQ Less than 4R
SEL670D
EL-50

METER AND GAUGES - Digital Type Combination Meter
Power Unit Check
Voltmeter
terminal
(f) (-)
E -
-%; 0
0
@I
__
@
9
0
0
Remove power unit with harness connected
Perform voltage and continuity tests Refer to
chart below
I Voltage
[VI
Approx 12
Approx 5
Approx 16
Approx 5
Approx 22
Approx 285
Turn ignition switch to "ON"
1 - 1 More than 6
Remarks
Check when no
display appears
For speedometer
For tachometer
For Temp,
Oil, Volt
sause
For Fuel gauge
For "Trip", "Ave
speed"
& "Dirt to
empty" meter
Turn ignition switch to "OFF"
Ohmmeter
Continuity Remarks
Check when no
ground display appears
If specified voltage or continuity is not produced,
replace power unit.
- Boost Sensor Check
1 Connect vacuum pump gauge to boost sensor
vacuum hose
2 Disconnect harness connector from boost
sensor and connect battery and voltmeter
as
shown
3 Apply vacuum pressure to boost sensor by
vacuum pump gauge and measure voltages
Approx.
2.2V at 0 kPa (0 mmHg, 0 inHg)
(Atmospheric pressure)
Approx.
1 3V
at -53.3 kPa (-400 mmHg, -15 75 inHg)
vacuum pump gauge
SEL674D
EL-53

METER AND GAUGES - Digital Type Combination Meter
Fuel Tank Gauge Check
For removal, refer to FE section
Ohmmeter terminal Float
Main gauge
Resistance value
Approx 10 - 20Q
Approx 480 - 520Q
Approx 100 - 1 1 OQ
Approx 4Q or below
Approx
870.930Q
Sub gauge
SEL675D
SEL676D
-Water Temp Sensor Check -
Cylinder head R H side
SEL677D
-Oil Pressure Sensor Check -
-
011 filter 7 \
SEL678D
Ohmmeter
terminal With engine With engine
stopped 1 running (idling)
ca On
+I;'''' I More than 74Q I Less than 60.Q
EL-56

METER AND GAUGES -Digital Type Combination Gauge
Trouble-shooting (Cont'd)
v
IGo to "Direction Sensor Amplifier Output Check" I
1 NG v
Check for loose harness
connector to
amplifier
Check for loose harness
connector to combmatlon
Replace combinatlon gauge Replace amplifier
I
1 Remove radio and AIC control assembly
from center console Remove combi-
nation gauge with harness connected
2. Turn ignition switch to "ON"
3 Check to determine if voltage IS produced
across
0 and @
SELSBSD
ACCELERATION & MILEAGE METERS
deceleration
Does speedometer operate?
1 No
Check harness between
combination gauge and
speed sensor Replace speed sensor
lNG
Replace combination gauge
Mileage meter registers "0" or abnormal value
I
Does speedometer operate?
Replace speed sensor
Check fuel injection pulse circuit for combination
gauge
I NG v
Check harness between
Replace combination
gauge combination gauge and
E F I control unit
IOK
EL-62

METER AND GAUGES -Needle Type Combination Meter
Combination Meter
pj
0, SENSO
35 36 31
1 TACHO-
METER
BBpgBW *Em 8EAR
FUEL BELT DOOR BRAKE CHARGE OIL RADIATO HEAD- STOP&
COOLANl LAMP TAIL LAMP
0 32 -- a: "E NATION 30
ILLUMI-
0 33 -U 18 19 20 s;14 15 5 23
24 2. 29 1 3 4 11
SEL690D
EL-65

METER AND GAUGES -Needle Type Combination Meter
Tacho, Fuel and Water Temperature Gauges/Wiring Diagram
C z >= oc
:E
I
6$ m
L
m
_I
I I
Y - m -
llllllI
1:
I
I1 I01 I I I IIIIIIII
r-
SELSSlD
EL-66

METER AND GAUGES -Needle Type Combination Meter
Ohmmeter
terminal
,+) , ~-, 1 Float position
Fuel Tank Gauge Check
For removal, refer to FE section
Resistance value
Full
00 EmpN
112
Approx 652
Approx 8052
Approx 30 - 3552
More than 6052
Less than 652
Main gauge
Sub gauge
SEL6750
SEL67SD
,-Speed Sensor Signal Check
Speed sensor is built into the speedometer
Turn speedometer slowly using small screw-
driver, and check continuity of speed sensor
circuit
Continuity exists two times for each turn . 0 K.
SEL696D
--Speedometer Cable Removal -

Press to
L? connect
SEL692D
EL-67