1984 NISSAN 300ZX time control syste

ELECTRICAL SYSTEM
I
SECTION EL
CONTENTS
HOW TO READ DIAGRAMS
STANDARDIZED RELAY
POWER SUPPLY ROUTING
BATTERY.
.. ..
STARTING SYSTEM .
STARTING SYSTEM -Starter -
CHARGING SYSTEM .
CHARGING SYSTEM - Alternator
COMB IN AT1 ON SWITCH
INSTRUMENT SWITCH
HEADLAMP
EXTERIOR LAMP,
INTERIOR LAMP
.
..
..
..
..
..
... ......
..
.. ....
..
.. ...
EL- 2
EL- 3
EL- 4
EL- 6
EL- 9
EL-
10
EL- 15
EL- 17
EL- 23
EL- 25
EL- 26
EL- 34
EL- 38
METER AND GAUGES - Digital Type Combination Meter . . EL- 41
METER AND GAUGES - Digital Type Combination Gauge . .. .. EL- 57
METER AND GAUGES - Needle Type Combination Meter .. . EL- 65
METER AND GAUGES
- Needle Type Combination Gauge.. .... EL- 68
WARNING LAMPS AND CHIME. .......... ... .... EL- 71
VOICE WARNING SYSTEM
... ... EL- 76
TIME CONTROL SYSTEM ... EL- 81
WIPER AND WASHER .... .... ... ... . EL- 89
HORN, CIGARETTE LIGHTER, CLOCK . . ......... EL- 92
REAR WINDOW DEFOGGER
... .. ... ....... EL- 93
AUDIO AND POWER ANTENNA
,. . .... .. . EL- 95
AUTOMATIC SPEED CONTROL DEVICE (AS
C D ) . ... , . EL- 97
LOCATION OF ELECTRICAL UNITS
... .. .. .. EL-104
HARNESS LAYOUT
. . .. .. .. . EL-107

FUSE BLOCK
I BATTERY I
TIME CONTROL UNIT [Refer to "TIME
CONTROL
SYSTEM
I I
LIR
@ SF models
IWhiIel DOOR STEP @ GLmodelr (Door harness R H I LAMP R H @ GLLmodelr
@ D8g1tal tv~e meter
@) Needle type meter
J~/~U
LIR U
I 1 II I
. BODY GROUND IL H ridel

rn I-
0 &
TIME CONTROL UNIT (Refer to 'TIME CONTROLSYSTEM" h
@$
STEP
LAMP R H @=@L/R L/E
INTERIOR
@
:;: STEP LAMP L H
@) Digital type meter
@ Needle type meter
J
Ii DOOR HANDLE
SWITCH
IDoor harness L H )
L/R
G/R KEY HOLE
ILLUMINATION

TIME CONTROL SYSTEM
CAUTION
Never touch the terminals of time control unit with bare hands.
1) Intermittent wiper control timer 5) Light warning timer
2) Interior lamp timer 6) Key warning timer
3) Door key hole illumination timer 7) Seat belt warning timer
4) Illumination control timer 8) Rear defogger timer
Time control unit has the following functions
ltNlTlON SWlTCH IGNITION lGNlTlON
FUSE
TlME CONTROLUNil /I
1
SEL705D
EL-81

TIME CONTROL SYSTEM
Wiring Diagram
SEL706D
EL-82

TIME CONTROL SYSTEM
Volwnetei terminals
- Preparation for Trouble-shooting -
1 Remove R H dash side cover and remove
blower motor
2 Remove time control unit with harness con-
nected
3 Connect main harness to instrument harness (if
disconnected)
Check from harness ride
Ignition switch pOIitiOn
harness connection SE L750D
I+)
-Power Supply Cercuit Check-
1-1 OFF ACC ON
@
@ 1 @ j ov 1 ov I Approx 17v
ov Approx Approx 12v 12v 0
Contlnult"
- Trou ble-shooting
intermittent wiper does not operate
4
I Go to "Power Supply Circuit Check"
OK NG
Check harness for T C U
power supply circuit
v
Check wiper relay circuit
OK NG
I Check wiDer relav I I
I
I 10 K ~NG
Check harness between Replace
T C U and wiper relay
Check wiper switch circuit check wiper relay
1 OK
I
Replace T C U Check wiper switch
Check harness between T C U Replace
and wiper switch
b
wiper switch
v
WIPER RELAY CIRCUIT CHECK
1 Turn wiper switch to "INT"
2 Turn ignition switch to "ACC"
3 Measure voltage across and 0
Check from harness ride
fTl7rFl
Wiper switch INT 0-12v lgnmon switch ACC
Needle shakes from 0 to 12V every 2 to 15 seconds
SEL708D
Voltmeter u
WIPER SWITCH CIRCUIT CHECK
1 Turn wiper switch to "INT"
2. Turn ignitionswitch to "OFF".
3 Check continuity between @ and @
Check from harness ride
Wiper switch INT
Ignition switch OFF
Ohmmeter
SEL709D
EL-83

TIME CONTROL SYSTEM
Trouble-shooting (Cont'd)
Intermittent time of wiper cannot be adjusted
Check intermittent wiper volume circuit
Check harness between T C U
and intermittent wiper volume
Replace
wiper switch
~~~_____ ~~ ~
1
2 Measure resistance between @J and @
Turn ignition switch to "OFF"
while turning intermittent wiper volume.
Check from harness side
Ignition switch OFF
0-1 kS2
Intermittent wiper knob
0 Rat S posmon
1 kR at L postiton Approx
Ohmmeter SEL710D
combination
Check washer switch circuit
I NG f
Replace T C U Check harness between
T C U and washer switch
1
2
3
Turn ignition switch to "OFF".
Turn washer switch to "ON"
Check continuity between @ and @
Check from harness side
lgnitjon rwrtch OFF
WASH
I
Ohmmeter SEL711D
EL-84

TIME CONTROL SYSTEM
Trouble-shooting (Cont'd)
(Interior lamp will not illuminate when outside door
handle
on driver's side IS pulled 1 I
Interior lamp and step lamps do not fade out after
all doors are closed
Check if door warning lamp goes off after all doors
are closed Check if interior lamp fades out after all doors
are closed
OK NG Check door switch
Go to "Interior lamp
circuit check" Go to "Power Supply Circuit Check"
OK NG
Check harness between
T C U and interior lamp
v
Check door handle switch circuit check
OK NG
Check door handle switch
Replace T C U Check harness between T c u
and door handle switch
NG
Check harness between
T C U and interior lamp
1
INTERIOR LAMP CIRCUIT CHECK
1 Turn Ignition switch to "OFF"
2 Measure voltage across @ and @
Check from harness ride
0 V when door 15 open 0- 12 V when
door IS closed after once opened
SEL7lZO
DOOR HANDLE SWITCH CIRCUIT
CHECK
1
2
3
Turn ignition switch to "OFF"
Pull outside door handle (driver's side)
Check continuity between @ and @
Check from harness sade
I OR
ye?! door handle (driver's rude)
SEL713D ohmmeter
EL-85