1982 Citroen CX torque

Downloaded from www.Manualslib.com manuals search engine 6 OPERATION No MA, 390.00 : C1 ,ararteristics
ad special fratuws oj the source
apfd rescr7,e o/ pressur(~ - Hydraulic system.
PRESSURE REGULATOR
MAIN ACCUMULATOR
Main occumulotor 7 Spring cup
O-ring 8 Cut-in spring
Spring base plate 9 Spring plug
Spring housing 10 Spring adjusting shims
Cut-out spring 11 O-ring
Spring odjusting shims 12 Snap ring
CHARACTERISTICS
Pressure regulator with pilot slide-valve :
- Cut-out pressure . .._......,_....____.............,.,......................................... 170 f 5 bars ( 2466 !I 73 psi ) _ Cut-in pressure __.....___.__.,..,.....,..,................,,...................................
145 + 5 bars ( 2103 + 73 psi )
Main accumulator :
- Capacity . . . . 0.400 litre ( 0.70 pints )
- Mark on filler plug . . , 62
- Calibrated pressure C /or checking purposes ) 62 + 2 bars (899 f 29 psi )
- 10 - 145
SPECIAL FEATURES
Pressure regulator :
- Thickness of adjusting shims . 0.30 mm
- For cut-out ..I.._......._..... .._. ,. .._. .:.. ,. ,. ..__.. ,. ..__ ,. ,. ._ ._.. .___ 0.30
mm
- For cut-in .._.... * .__....._._.,.,.,._.,....................................... 0.30 and 0.70 mm
- One .30 mm shim brings about a change in pressure by . . . . . . . . . . , approx. 3 bars (44 psi 1
- One .70 mm shim brings about a change in pressure by . . . . . . . . . approx. 7 bars ( 102 psi )
Ti$ttening torques :
- pressure regulator fixing Screws . . . . .._.__.....__._............................... 1.8 daNm ( 13 ft.Ib )
- Main accumulator ..,.. ,. . . ,. __ . . . . .._. ., ,__. ._ __ 2.5 to 4.5 daNm ( 18 to 32 l/2 ft.lb )

Downloaded from www.Manualslib.com manuals search engine BRAKE ACCUMULATOR
1 I’r~rc~(,r-s!(,(,riri~ I cbic-lcc5 J
HP
To brake valve
--
Front brakes supply Supply :
- steering governor
- safety valve CHARACTERISTICS
Brake accumulator :
- Capacity .._._._.._.._.___._____._._._..__........ _._____ _......._._.___._ _____..____.___ ___._._._._._._. 0 400 litre ( C. 70 pts )
- Identification mark on filler plug ,...........
62
- Calibration pressure f /or rhc,c-kir/~ J 62 _ 3z bars ( 899 1 dTd psi ) SPECIAL FEATURES
Tightening torque :
- Accumulator. onto its mounting .,..... .., .._.. .._.. .._....._._._. 3 daNm ( 21 l/ 2 ft.lb )

Downloaded from www.Manualslib.com manuals search engine 4 Turn the wheels 20’ inwards.
Set apparatus back to horizontal position.
Resentre spirit-level bubble ( 2) by turning disc(l).
Read off castor angle on RWCJ,J scnlr (at a a )) ).
Castor angle must be
between 0’25’ and 1015
O”erall.
If not, adjust castor angle
Adiusting castor angle :
IMPORTANT NOTE :
To carry out this adjustment it is essential to
use tool 6312 T class 2 which is required for fitting
lower wheelorm on front axle.
a) Remove :
wheel,
lower arm and castor angle adjusting shims (3 )
b)
Determining distribution of shims :
NOTES :
A minimum of 1 shim should be set on each
side of the wheelarm.
- Movement of
1 mm will vary castor angle by
15’.
Total thickness of shims fitted must corres-
pond to the total thickness of shims found on
dismantling, in order to maintain the correct
assembly of the wheelarm in axle unit.
c) Fit:
Lower wheelarm and shims (3 ).
Tightening torque on wheelarm spindle nut (4)
130 mc\U ( 13 m.kg ) (94 ft.lb).
wheel
d) Check castor angle.

Downloaded from www.Manualslib.com manuals search engine OPERATION No MA. 410-O : I hvr-6iq n,,d od;n.s/isg /hc /~,a, nrle uei/ Op. MA. 410-O 7
’ 15b20° 5. Adiust the wheel alignment :
\‘chirl‘,s II ilh mw,r,ol s/wrh,i: :
Slacken locknuts (2 ).
Rotate the ball-joint stems ( 1) a froctmn of a turn
at a time to obtain correct setting.
NOTE Rotate each stem the same’ amount.
- One complete rotation of each stem alters the
adjustment by 4 mm approximately. Tighten locknuts (2) from 3.6 to 4 daNm (26 to
29 ft.lb ).
Check the adjustment
IMPORTANT The length at (< a n of the visible
thread on the L.H. and R.H. trackrods ,,,r,s/ lx,
vq,,nl IO rrithin 2 ,,,7,,,
Slacken collars ( 3).
Turn sleeves (4) ~1 fraction of a turn at a time to
obtain correct setting.
NOTE Turn each
sleeve the same amount in order
to retain the oiiqnment with the rear axle unit.
I Son<, wcidisp on varh sidv o,, gmd,,lrrn/r,d rules A I
One complete turn of each sleeve alters the
adjustment by 7 mm.
Position the two collars ( 3) (IS indicated on
photograph. Ti.ghtening torque of screws - 0.9 daNm.
( 6 l/2 ft.lb ).

Downloaded from www.Manualslib.com manuals search engine OPERATION No MA. 4104 : (./ , k’ 1<, jr.or,/ ovl<, ,,i,it Op. MA’. 410-O 9
ADJUSTMENT
NOTE The steering crossmember will have to be
moved (IS a function of the readings obtained during
checkinq
01) Towards the top to
obtain
_ toe-out ir, Ihe hish positim
- toe-in irr the 10~ psitios
b) Towards the bottom
to obtain
.
toe-in in Ihr hi& posilins
- toe-out iu fhc IOU posilios
4. Remove the rubber shields ( 1 ) from the wheel-
arches.
5. On each ,upper wheelorm spindle (2 ). position
tools 6451-T, screw (3) resting on steering
crossmember ( 4 1.
NOTE.
6. Slacken nut ( 5) and screw (6 1 securing the wind-
screen crossmember. on the side to be moved.
Slacken the upper fixing nut on the opposite
side as well li,r order 10 nrmoid rlistorfina II><,
crr~.ss,nP”,b<~r ,,
7. Move the crossmember in the direct& decided,
by using (1s a mark extremity (( a u of screw ( 3).
8. Tighten ‘the fixing nuts and the screw for the
crossmember. Tightening torque : 2.5 ta 2.8 doNm ( 18 ta
20 l/2 ft.lb ).
9. Check once mew the variations in wheel aliqn-
merit. and alter the position of steering cross-
member. if necessary. 10.
Remove tools 6451-T and fit the rubber shields
to the wheelarches.
Adjust if necessary. 11.
Check the toe-in of the front wheels 1 to 4 mm.

Downloaded from www.Manualslib.com manuals search engine OPERATION No MA. 430.00 : c ,,<,,a< ,<,r;s,;rs mi/ .s/wrin/ ,vn/srrs oi /he srmf~rw.~ion Op. MA. 430-00 5
II. SPECIAL FEATURES
Adjusting the anti-roll bars :
A, t/xv ,ms,
- Lateral positioning equal protrusion on either side to within 2 mm
- Anti-roll bar bearing preload 300 N ( 30kg) ( 66 lb )
- Lateral clearance of anti-roll bar. under pressure of 500 N i 50kq I( 110 fb i 0.2 to 1 mm
,I, l/X“ rcnr :
- Lateral positioning same thickness of shim on both sides. within 1 mm
- Shimming, if necessary. level with the split collars to within 0.6 mm
Greasing of the suspension piston con-rod ioint :
( Carried out with LHM liquid contained in the dust cover )
- Front suspension cylinder
- Rear suspension cylinder
Upper front wheelarm stops :
WARNING ‘,hc ,,,;,,,i<~, ~,op ,,,I (i, he ii,,, r/ 01 //I< ,,I?<,<‘/ wd. 7cm3
25 cm3
Tightening torques :
- Anti-roll bar link-rod on upper wheelarm. i Bush nut 3 doNm ( 21 11 2 ft.lb )
NYLSTOP nut 4.5 to 5daNd32 1/‘2to 36ft.lb)
- Link-rod on anti-roll bar 4.5 to SdaNm(32 1/2to36ft.lb)
. Screw securing front anti-roll bar bearing 2.7 daNm ( 19 l/2 ft.lb )
^ - Clamps for adjusting pie-load on front anti-roll bar 13 doNm ( 9 l/2 ft.lb)
b2 - 1.5 daNm [ 11 ft.lb i
0 Clomp for height corrector control
rod ( front and rem )
”
6 daNm ( 43 l/ 2 ft.lb ) - . An+iwroff bar 0” rear &&arm ( rear fixing
points ) I /nc<’ nvrl /hrcn,l~r &
- Rear anti-roll bar split collars :
cc
-5 Tightening torque for screw ( 1 )
according to width (e) of bearing :
:
2
e = 5 mm 8 d.aNm ( 58 ft.lb ) f -I’, I’JiS,
P
e-6mm lOdoNm( lOft.lb)i 121Vi-’
Fitting of the front and rear wheelarm stops using water
Fitting of the front anti-011 bar bearing shells using ,< TOTAL MULTIS I) grease.

Downloaded from www.Manualslib.com manuals search engine OPERATION No MA. 430-O : Checking md ndjusting the suspcusion and its control. 06. MA. 430-O i
ADJUSTING THE HEIGHTS
AT FRONT : Between under-face of point (c o ))
subfrome ond point of contoct of wheels with
ground.
AT REAR : Between under-face of point <( b a)
subfrome ond point of contact of wheels with
ground.
1. Check tyre pressures.
2. Remove corrector protectors and make sure the
manual control rods are not exerting pressure on
levers ( 1) and ( 2).
3. Slightly loosen automatic control clump and
adjust to obtain :
3
Front height = 165 ? 8 mm
Rear height = 215 ? 8 mm ( Saloons )
228 t 8 mm ( Estates )
Tightening torque of clomps = 1.5 doNm (11 ft.lb )

Downloaded from www.Manualslib.com manuals search engine ll, SPECIAL FEATURES
STEERING PINION
After adjusting wheel alignment, protrusion of track-rod thread in relation to lock-nut must be equal on either side
( .to within 2 mm )
Rack centre-point Protrusion of rack must be equal on either side of rack housing
- Clearance at rack plunger ( at minimum clearance point ) .O.l to 0.25
( at minimum clearance point ) ., .,...._...... .._._ 0 1 to 0.25 mm
- Rotational torque of pinion, after
adjustment of plunger .._..... .._.... 1.2 daNm ( 8 l/2 ft.lb)
L 44.3
Steering control :
- Clearance between universal joint, steering shaft and fixed
steering wheel tube spacer 0.25 to 1 mm
.._....__._..._.... ._..__..
- Position of steering wheel spoke in (( straight-ahead ))
position. single spoke pointing vertically downwards
- Angle of universal joint : 17” to the left approx. (with steering
wheel in (( straight-ahead )) position.
- Coupling for steering pinion flange ( steering shaft ) ....................................
- Flange on steering pinion ................................................................................
- Steering pinion securing flange ........................................................................
- Steering rack ball joint f rack Jacked )’ .............................................................
- Track-rod lock-nut ..............................................................................................
- Rack housing on steering crossmember ..........................................................
-. Steering crossmember on front subframe ..........................................................
- Nut for track-rod ball-joint ................. ................................... ..... ...................... Tightening torques :
- Flange for universal joint on steering shaft __..._.__.._._.........,.........................,. 1.3 to 1.4 daNm ( 9 11 2 to
lOft.lb)
- Fixed steering wheel tube attachments
. . . . . . . . . . . . . . . . . . . . . 1 9 to 2.1 daNm (13 l/2 to15ft.lb)
3.1 to 3.4 daNm (22 l/2 to 241/2ft,lb)
1.3 to 1.4 daNm ( 9 l/ 2 to 10 ft.lb)
1.3 to 1.4 daNm (9 l/2 to 10 ft.lb)
.5 to’5.5 daNm (36 to 40 ft.lb)
3.6 to 4 daNm ( 26 to 29 ft.lb)
2.5 to 2.8 daNm ( 18 to 20 l/2 ft.lb)
2.5 to 2.8 daNm (18 to 20 1/2ft.lb)
9 to 10 daNm ( 65 to 72 l/2 ft.lb)
- Greasing of steering rack TOTAL MULTIS MS