1982 CHEVROLET CAMARO battery location

GM – CAMARO 1982-1992 – Repair Guide (Checked by WxMax) 22

Fig. 8: Main pillar rail components


Fig. 9: Upstop and downst op adjustment locations
1. Disconnect the negative battery cable.
2. Remove the side rails and retainers.
3. Remove the main pillar seals and retainers.

GM – CAMARO 1982-1992 – Repair Guide (Checked by WxMax) 73
To install:
9. Install the new line or hose, starti
ng with the end farthest from the master
cylinder. Connect the other end, then confirm that both fittings are correctly
threaded and turn smoothly using finger pressure. Make sure the new line
will not rub against any ot her part. Brake lines must be at least 1/2 in.
(13mm) from the steering column and other moving parts. Any protective
shielding or insulators must be rein stalled in the original location.
WARNING - Make sure the hose is NO T kinked or touching any part of the
frame or suspension after installation. These conditions may cause the hose to
fail prematurely.
10. Using two wrenches as bef ore, tighten each fitting.
11. Install any retaining clips or brackets on the lines.
12. If removed, install the wheel and tire assemblies, then carefully lower the
vehicle to the ground.
13. Refill the brake master cylinder re servoir with clean, fresh brake fluid,
meeting DOT 3 specifications. Pr operly bleed the brake system.
14. Connect the negative battery cable.

BLEEDING

Fig. 1: Caliper bleeding

GM – CAMARO 1982-1992 – Repair Guide (Checked by WxMax) 148
ARMING SENSOR
The arming sensor is a protective switch
located in the power feed side of the
deployment loop. It is calibrated to clos e at low level velocity changes (lower
than the discriminating sens ors). This assures that the inflator module is
connected directly to the 36 volt output of the DERM or battery voltage feed
when either of the discrim inating sensors close.
DISCRIMINATING SENSORS
The discriminating sensors are wired in parallel on the ground side of the
deployment loop. These sensors are calib rated to close with velocity changes
which are severe enough to warrant deployment.
SIR COIL ASSEMBLY
The SIR coil assembly consists of two cu rrent carrying coils. They are attached
to the steering column and allow rotation of the steering wheel while maintaining
continuous contact of the deployment loop to the inflator module.
INFLATOR MODULES
Each inflator module consists of an inflat able bag and an inflator (a canister of
gas generating material with an initiati ng device). When the vehicle is in a
frontal crash of sufficient force, current flows through the deployment loops.
Current flowing through the initiator ignite s the material in the inflator module.
The gas produced from this reaction rapidly inflates the air bag.

Fig. 2: Forward discriminating se nsor location on 1990-1992 models

GM – CAMARO 1982-1992 – Repair Guide (Checked by WxMax) 363
2.5L ENGINE

Fig. 1: Engine mountin g points for the 2.5L
1. Disconnect the negative battery cable.
2. Remove the air cleaner duct.
3. Mark the hood location on the hood supports and remove the hood.
4. Remove the water pump drive belt.

GM – CAMARO 1982-1992 – Repair Guide (Checked by WxMax) 365
31. Connect the bulkhead harness connec
tor, wires and hoses. Reroute the
ECM harness in its original location. Install the hush panel and fenderwell
splash panel.
32. Install the radiator, fan and fan sh roud. Connect the radiator and heater
hoses, along with the transmission cooler lines.
33. Connect the vacuum brake booster li ne, the throttle linkage and cruise
control cable. Install the distributor cap.
34. Fill the cooling system with the proper type and amount of coolant and
the crankcase with the proper type of oil to the correct level.
35. Install the water pump drive bel t, the air cleaner duct and the hood.
36. Connect the negative battery cable, st art the engine and check for leaks.
2.8L AND 3.1L ENGINES

Fig. 2: Engine mountin g points for the V6
1. Disconnect the negative battery cable.
2. Remove the air cleaner duct.
3. Mark the hood location on the hood supports and remove the hood.
4. Remove the water pump drive belt.
5. Drain the radiator and remove t he radiator hoses. Disconnect the heater
hoses and the transmission cooler lines.
6. Remove the fan shroud, fan and radiator.
7. Disconnect the throttle linkage, includi ng the cruise control detent cable.

GM – CAMARO 1982-1992 – Repair Guide (Checked by WxMax) 367
5.0L AND 5.7L ENGINES

Fig. 3: Engine mountin g points for the V8
1. Disconnect the negative battery cable.
2. Mark the location of the hood on the hood hinges and remove the hood.
3. Remove the air cleaner.
4. Drain the cooling system.
5. Remove the radiator hoses.
6. Disconnect the transmission cooler li nes, the electrical connectors and
retaining clips at the fan and remove the fan and shroud.
7. Remove the radiator.
8. Remove the accessory drive belt.
9. Disconnect the throttle cable.
10. Remove the plenum extension scr ews and the plenum extension, if
equipped.
11. Disconnect the spark plug wires at the distributor and remove the
distributor.
12. Disconnect the necessary vacuum hoses and wiring.
13. Disconnect the power steering and air conditioning compressors from
their respective brackets and lay them aside.
14. Properly relieve the fuel system pressure. Disconnect the fuel lines.
15. Disconnect the negative battery cable at the engine block.
16. Raise and safely support the vehicle.
17. Remove the exhaust pipes at the exhaust manifolds.
18. Remove the flywheel cover and remove the converter to flywheel bolts.
19. Disconnect the starter wires.
20. Remove the bellhousing bolts and the motor mount through-bolts.
21. Lower the vehicle.
22. Support the transmission with a suitable jack.

GM – CAMARO 1982-1992 – Repair Guide (Checked by WxMax) 377

Fig. 4: Then remove the rocker arm pivot
Be sure to keep all the components in t he exact order of removal so they may
be installed in there original location; adjust the valve lash after replacing the
rocker arms. Coat the replacement ro cker arm and ball with engine oil before
installation.
Rocker arms studs that have damaged thr eads or are loose in the cylinder
heads may be replaced by reaming the bore and installing oversize studs.
Oversizes available are 0.003 in. (0. 076mm) and 0.013 in (0.33mm). The bore
may also be tapped and screw-in studs installed. Several aftermarket
companies produce complete rocker arm st ud kits with installation tools.
The 2.5L engine use bolts instead of studs, 2.8L and 3.1L engines use threaded
studs, the 3.4L, 5.0L and 5.7L engines use press fit studs.
EXCEPT 2.5L ENGINES 1. Disconnect the negative (-) battery cable.
2. Remove the rocker arm cover as outlined in this section
3. Remove the rocker arm nuts, balls and rocker arms. Place components
in a rack so they can be reinstalled in the same location.
To install: 4. Coat the bearings surf aces with a thin coating of Molykote® or its
equivalent.
5. Install the pushrods and make sure the rod is in the lifter seat.

GM – CAMARO 1982-1992 – Repair Guide (Checked by WxMax) 378
6. Install the rocker arm, balls and
nut. Tighten the nut until all lash is
eliminated.
7. The engine must be on the No. 1 fi ring position before proceeding. This
may be determined by placing your fi ngers on the No. 1 rocker arms as
the mark crankshaft damper is rotat ed towards the "0" on the timing tab.
If the arms did not move, it is in the No. 1 firing position. If they did move,
turn the crankshaft one full revoluti on to reach the No. 1 position.
Remember, the mark on the crankshaft balancer must be aligned with
the "0" on the timing tab.
8. Adjust the valves as follows:
V6 ENGINES
With the engine on the number 1 firing pos ition, exhaust valves 1, 2 and 3 and
intake valves 1, 5 and 6
may be adjusted. Back out t he adjusting nut until lash is felt at the pushrod.
Tighten the adjusting nut unt il all lash is removed, then tighten the nut an
additional 1
1/2 turns to center the lifter plun ger. Turn the engine one revolution
until the "0" timing mark is once again al igned. Exhaust valves 4, 5 and 6 and
intake valves 2, 3 and 4 may be adjusted.
V8 ENGINES
With the engine on the number 1 firing posit ion, exhaust valves 1, 3, 4 and 8,
intake valves 1, 2, 5 and 7 may be adj usted. Back out the adjusting nut until
lash is felt at the pushrod. Tighten the adjusting nut until all lash is removed,
then tighten an additional 1 turn to center the lifter plunger. Turn the engine one
revolution until the 0 timing mark is once again aligned. Exhaust valves 2, 5, 6
and 7, intake valves 3, 4, 6 and 8 may be adjusted.
9. Install the rocker arm cover.
2.5L ENGINE 1. Disconnect the negative battery cable.
2. Remove the valve cover.
3. Remove the rocker arm bolt, ball and rocker arm.
4. Remove the pushrods, if necessary . Place components in a rack so they
can be reinstalled in the same location.
To install: 5. Coat the bearings surf aces with a thin coating of Molykote® or its
equivalent.
6. Install the pushrod, if removed, through the cylinder head and into the
lifter seat.
7. Install the rocker arm, ball and bol t. Torque to 22 ft lbs. (30 Nm).
8. Install the valve cover.