1969 FORD MUSTANG stop start

07-02-07
C4 Automatic Transmission

07-02-07

2.
Remove the selector lever handle

from the lever.

3.
Remove the trim panel from the

top of the console.

4.
Remove the cover and dial indi-

cator as an assembly.

5.
Remove the four screws that se-

cure the selector lever retainer to the

selector lever housing. Lift the retainer

from the housing.

6. Loosen the two combination

starter neutral and back-up light

switch attaching screws (Fig. 10).

7.
Move the selector lever back and

forth until the gauge pin (No. 43 drill)

can be fully inserted into the gauge

pin holes (Fig. 10).

8. Place the transmission selector

lever firmly against the stop of the

neutral detent position.

9. Slide the combination starter

neutral and back-up light switch for-

ward or rearward as required, until

the switch actuating lever contacts the

selector lever.

10.
Tighten the switch attaching

screws and remove the gauge pin.

Check for starting in the park posi-

tion.

11.
Turn the ignition key to the

ACC position and place the selector

lever in the reverse position and check

the operation of the back-up lights.

Turn the key off.

12.
Position the selector lever re-

tainer to the selector lever housing.

Install the four attaching screws.

13.
Install the cover and dial indi-

cator.

14.
Install the trim panel on the top

of the console. Install the selector

lever handle.

MUSTANG

1.
With the manual lever properly

NEUTRAL
START

SWITCH

(D1439-A

FIG. 11—Neutral Start Switch

Adjustments—Console Shift—

Mustang
adjusted, loosen the two switch attach-

ing bolts (Fig. 11).

2.
With the transmission manual

lever in neutral, rotate the switch and

insert the gauge pin (No. 43 drill

shank end) into the gauge pin holes of

the switch. The gauge pin has to be

inserted to a full 31/64 inch into the

three holes of the switch (Fig. 11).

3.
Torque the two switch attaching

bolts to specification. Remove the

gauge pin from the switch.

4.
Check the operation of the

switch. The engine should start only

with the transmission selector lever in

Neutral and Park.

NEUTRAL START SWITCH

REPLACEMENT—CONSOLE SHIFT

On vehicles equipped with a column

mounted neutral start switch, refer to

Part 7-1, Section 2, for the replace-

ment procedures.

FORD-METEOR

1.
Remove the four screws and

plates securing the selector lever

handle to the lever. Remove the

handle and detent control.

2.
Remove the two screws from the

rear of the console top panel. Pull the

panel back to unhook it from the

front of the console and remove the

panel.

3.
Remove the two screws securing

the dial indicator assembly to the se-

lector lever housing and remove the

indicator assembly.

4.
Disconnect the neutral start

switch wires at the plug connector.

Remove the wires from under the re-

taining clip.

5.
Remove the two screws securing

the neutral start switch to the selector

lever housing and remove the switch

(Fig. 9).

6. Position the neutral start switch

to the selector lever housing and in-

stall the two attaching screws.

7.
Adjust the neutral start switch as

outlined under the Neutral Start

Switch Adjustment procedures in this

section.

8. Connect the neutral start switch

wires to the plug connector. Position

the wires in the retaining clip and

close the clip.

9. Place the console top panel on

the console and install the retaining

screws.

10.
Position the selector lever de-

tent control and handle on the selector

lever and secure with the four plates

and attaching screws.

FAIRLANE-MONTEGO

1.
Remove the selector lever handle

from the lever.
2.
Remove the trim panel from the

top of the console.

3.
Remove the cover and dial indi-

cator as an assembly.

4.
Remove the four screws that se-

cure the selector lever retainer to the

selector lever housing. Lift the retainer

from the housing.

5.
Remove the two screws securing

the neutral start switch to the selector

lever housing. Disconnect the neutral

start switch wires at the plug connec-

tor and remove the switch.

6. Position the neutral start switch

to the selector lever housing and in-

stall the two attaching screws.

7.
With the selector lever in neu-

tral,
move the selector lever back and

forth until the gauge pin (No. 43 drill)

can be fully inserted into the gauge

pin holes (Fig. 10).

8. Place the transmission selector

lever firmly against the stop of the

neutral detent position.

9. Slide the combination starter

neutral and back-up light switch for-

ward or rearward as required, until

the switch actuating lever contacts the

selector lever.

10.
Tighten the switch attaching

screws and remove the gauge pin.

11.
Connect the neutral start switch

wires to the plug connector and check

for starting in the park position.

12.
Position the selector lever re-

tainer to the selector lever housing.

Install the attaching screws.

13.
Install the cover and dial indi-

cator.

14.
Install the trim panel on the top

of the console. Install the selector

lever handle

MUSTANG

1.
Remove the downshift linkage

rod from the transmission downshift

lever.

2.
Apply penetrating oil to the

downshift lever shaft and nut. Remove

the transmission downshift outer lever

retaining nut and lever (Fig. 11).

3.
Remove the two neutral start

switch attaching bolts.

4.
Disconnect the multiple wire

connector. Remove the neutral switch

from the transmission.

5.
Install the neutral start switch on

the transmission. Install the two at-

taching bolts.

6. With the transmission manual

lever in neutral, rotate the switch and

install gauge pin (No. 43 drill) into

the gauge pin hole (Fig. 11).

7.
Tighten the switch attaching

bolts to specification and remove the

gauge pin.procarmanuals.com

07-03-05
FMX Transmission
07-03-05

IN-VEHICLE ADJUSTMENTS AND REPAIRS

CONTROL LINKAGE

ADJUSTMENTS

The transmission control linkage

adjustments should be performed in

the order in which they appear in this

section of the manual.

THROTTLE AND

DOWNSHIFT LINKAGE

ADJUSTMENTS

Adjusting the throttle linkage is im-

portant to be certain the throttle and

kickdown systems are properly adjust-

ed. The kickdown system should come

in when the accelerator is pressed

through detent, and not before detent.

Refer to Group 10 for detailed

throttle and downshift linkage adjust-

ment procedures.

MANUAL LINKAGE

ADJUSTMENT

COLUMN SHIFT

1.
Place the selector lever in the D

position tight against the stop.

2.
Loosen the shift rod adjusting

nut at point A (Fig. 4 or 5).

3.
Shift the manual lever at the

transmission into the D detent posi-

tion, third from the rear.

4.
Make sure that the selector lever

has not moved from the D stop, then

tighten the nut at point A to 10-20 ft-

lbs.

5.
Check the pointer alignment and

the transmission operation for all se-

lector lever detent positions.

CONSOLE SHIFT

1.
Position the transmission selec-

tor lever in D position.

2.
Raise the vehicle and loosen the

manual lever shift rod retaining nut

(Fig. 6 or 7). Move the transmission

manual lever to the D position, fourth

detent position from the back of the

transmission.

3.
With the transmission selector

lever and manual lever in the D posi-

tions,
torque the attaching nut 10 to

20 ft-lbs.

4.
Check the operation of the trans-

mission in each selector lever position.
COLUMN SHIFT LEVER

€>

TRANSMISSION

MANUAL LEVER

FIG. 4—Manual Linkage—Column Shift—Ford-Mteor

D2024-A

FIG. 5—Manual Linkage—Column Shift—Fairlane-Montego

NEUTRAL START SWITCH

ADJUSTMENT

CONSOLE SHIFT

On vehicles equipped with a

column-mounted neutral start switch,

refer to Part 7-1, Section 2, for the

adjustment procedures.

FAIRLANE-MONTEGO

1.
With the manual linkage proper-

ly adjusted, check the starter en-

gagement circuit in all positions. The

circuit must be open in all drive posi-

tions and closed only in park and neu-

tral.

2.
Remove the selector lever handle

from the lever.
3.
Remove the trim panel from the

top of the console.

4.
Remove the cover and dial indi-

cator as an assembly.

5.
Remove the four screws that se-

cure the selector lever retainer to the

selector lever housing. Lift the retainer

from the housing.

6. Loosen the two combination

starter neutral and back-up light

switch attaching screws (Fig. 8).

7.
Move the selector lever back and

forth until the gauge pin (No. 43 drill)

can be fully inserted into the gauge

pin holes (Fig. 8).

8. Place the transmission selector

lever firmly against the stop of the

neutral detent position.procarmanuals.com

07-03-07
FMX Transmission

07-03-07

Gauge Pin

(No.
43 Drill)

NEUTRAL START

SWITCH

ADJUSTMENT

SCREWS

D 1759-A

FIG. 8—
Neutral
Start Switch-

Console Shift—Fairlane-Montego

9. Slide the combination starter

neutral and back-up light switch for-

ward or rearward as required, until

the switch actuating lever contacts the

selector lever.

10.
Tighten the switch attaching

screws and remove the gauge pin.

Check for starting in the park posi-

tion.

11.
Turn the ignition key to the

ACC position and place the selector

lever in the reverse position and check

the operation of the back-up lights.

Turn the key off.

12.
Position the selector lever re-

tainer to the selector lever housing.

Install the four attaching screws.

13.
Install the cover and dial indi-

cator.

14.
Install the trim panel on the top

of the console. Install the selector

lever handle.

MUSTANG-COUGAR

1.
With the manual linkage proper-

ly adjusted and the engine turned off,

place the selector lever in the N (Neu-

tral) position. Then, shift the selector

lever from neutral to 1, to P (park)

and back to neutral. Shifting the se-

lector lever through this shift pattern

should adjust the switch automatical-

ly. If not, adjust it manually as fol-

lows:

2.
With the selector lever in neu-

tral,
remove the selector lever handle

attaching screw and remove the

handle (Fig. 7).

3.
Remove the dial housing attach-

ing screws and remove the housing.

4.
Remove the two pointer back-up

shield attaching screws and remove

the shield.
NEUTRAL START SWITCH

AND HARNESS ASSEMBLY

32027-A

FIG. 9—Neutral Start Switch—Console Shift—Mustang-Cougar

5.
Remove the two screws securing

the neutral start switch to the selector

lever housing.

6. Lift the switch from the housing

and move the actuator lever all the

way to the left. Then, return the actu-

ator lever to the neutral position as

shown in Figure 9.

7.
Position the neutral switch as-

sembly to the selector lever housing,

and secure with the two attaching

screws.

8. Place the selector lever in the P

(Park) position and check the opera-

tion of the switch. The engine should

start with the selector lever in the

park position. If the engine does not

start, replace the switch. Refer to the

Neutral Start Switch Replacement

procedures in this section.

9. Install the pointer back-up shield

on the housing and lever assembly.

10.
Install the dial housing on the

selector lever housing assembly.

11.
Install the selector lever.'handle.

NEUTRAL START SWITCH

REPLACEMENT-

CONSOLE SHIFT

On vehicles equipped with a

column-mounted neutral start switch,

refer to Part 7-1, Section 2, for the

replacement procedures.

FAIRLANE-MONTEGO

1.
Remove the selector lever handle

from the lever.
2.
Remove the trim panel from the

top of the console.

3.
Remove the cover and dial indi-

cator as an assembly.

4.
Remove the four screws that se-

cure the selector lever retainer to the

selector lever housing. Lift the retainer

from the housing.

5.
Remove the two screws securing

the neutral start switch to the selector

lever housing. Disconnect the neutral

start switch wires at the plug connec-

tor and remove the switch.

6. Position the neutral start switch

to the selector lever housing and in-

stall the two attaching screws.

7.
With the selector lever in neu-

tral,
move the selector lever back and

forth until the gauge pin (No. 43 drill)

can be fully inserted into the gauge

pin holes (Fig. 8).

8. Place the transmission selector

lever firmly against the stop of the

neutral detent position.

9. Slide the combination starter

neutral and back-up light switch for-

ward or rearward as required, until

the switch actuating lever contacts the

selector lever.

10.
Tighten the switch attaching

screws and remove the gauge pin.

11.
Connect the neutral start switch

wires to the plug connector and check

for starting in the park position.

12.
Position the selector lever re-

tainer to the selector lever housing.

Install the attaching screws.

13.
Install the cover and dial indi-

cator.procarmanuals.com

07-03-11
FMX Transmission

07
03-11

GOVERNOR
COMPENSATOR

PRESSURE TUBE
MAIN CONTROL

VALVE TUBE

COUNTERWEIGHT

D 1815-A

FIG. 16—Governor Installed

ber to remove all weight from the

housing.

10.
Loosen the parking brake cable

adjustment nut enough to disconnect

the cables from the equalizer.

11.
Remove the extension housing

attaching bolts. Slide the housing off

the output shaft and remove the gas-

ket. When removing
the
extension

housing and/or governor, hold
the

output shaft
and
rear support from

moving rearward
to
prevent
the
needle

bearing
and
race from dropping
out of

location.

12.
Remove the governor to coun-

terweight attaching screws. Lift the

governor from the counterweight (Fig.

16).

13.
Lubricate the governor valve

parts with clean transmission fluid.

Make certain that
the
valve moves

freely
in the
valve body bore.

14.
Position the governor valve

body on the counterweight with the

cover facing toward the front of the

vehicle. Install and tighten the two at-

taching screws to the specified torque.

15.
Position a new extension hous-

ing gasket on the rear of the transmis-

sion case.

16.
Slide the extension housing into

place and secure it to the transmission

case with the attaching bolts. Torque

the bolts to specification. With the ex-

tension housing installed, rotate
the

output shaft.
The
shaft must rotate

freely
by
hand.
If the
shaft
is
tight
or

bound
up, it is
likely that
the
needle

bearing
and
race have dropped
out of

location,
in
which case,
the
transmis-

sion must
be
partially disassembled

and
the
bearing
and
race repositioned.

17.
Connect the speedometer cable

to the extension housing.

18.
Raise the transmission high

enough with a jack to position the en-
FRONT SERVO

FLUID TUBES

PRESSURE

REGULATOR

D 1817-A

FIG. 17—Typical Hydraulic Control System

gine rear support on the crossmember.

Secure the support to the crossmem-

ber with attaching bolt.

19.
Lower the transmission and re-

move the jack. Secure the extension

housing to the rear support with the

two attaching bolts.

20.
Connect the parking brake

cables to the equalizer and adjust the

cables as required.

21.
Install the driveshaft.

22.
Fill the transmission to the cor-

rect level with the specified fluid.

OIL
PAN AND
CONTROL

VALVE BODY REPLACEMENT

1. Raise the vehicle so that the

transmission fluid pan is accessible.

2.
Drain the fluid from the trans-

mission by loosening the pan attach-

ing bolts starting at the rear of the

pan and working toward the front.

When most of the fluid has drained

from the pan, remove the remainder

of the attaching bolts. Remove the

pan and gasket. Discard the gasket. If

the same fluid is to be used again in

the transmission, filter the fluid

through a 100-mesh screen before in-

stalling it in the transmission. Re-use

the fluid only if it is in good condi-

tion.
3.
Disconnect the hose from the

vacuum diaphragm unit. Remove the

diaphragm unit using tool FCO-24.

Do
not use any
tools
on the dia-

phragm housing, such
as
pliers, pipe

wrenches,
etc. Do not
allow solvents

to enter
the
diaphragm unit. Remove

the push rod. Remove the fluid screen

retaining clip and the screen.

4.
Remove the fluid filter retaining

clip and the filter.

5.
Remove the two tubes which

connect to the pressure regulator and

the control valve body (Fig. 17).

6. Loosen the front servo attaching

bolts three turns.

7.
Remove the three control valve

body attaching bolts, and lower the

valve body while pulling it off the

front servo tubes. Be carefull not to

damage
the
valve body
or the
tubes.

8.
Before installing the control

valve body, check for a bent manual

valve by rolling it on a flat surface.

9. Install the control valve body by

aligning the front servo tubes with the

holes in the valve body. Shift the man-

ual lever to the 1 detent, and place the

inner downshift lever between the

downshift lever stop and the downshift

valve.
The
manual valve must engage

the actuating
pin in the
manual detent

lever.

10.
Install but do not tighten, the

control valve body attaching bolts.procarmanuals.com

07-03-14
FMX Transmission

07-03-14

REMOVAL AND INSTALLATION

An oil impregnated plastic grommet

is incorporated in the end of the man-

ual shift linkage lever arm on all col-

umn shift vehicles. A special tool

T67P-7341-A is required to install the

grommet in the manual lever, and to

install the manual linkage rod into the

grommet. Refer to Part 7-1, Section

2,
for the grommet replacement pro-

cedures.

TRANSMISSION AND

CONVERTER REPLACEMENT—

FORD-METEOR

REMOVAL

1.
Drive the vehicle on a hoist, but

do not raise at this time.

2.
Remove the two upper bolts and

lock washers which attach the con-

verter housing to the engine.

3.
Raise the vehicle and remove the

cover from the lower front side of the

converter housing. Drain the fluid

from the transmission.

4.
Remove one of the converter

drain plugs. Then rotate the converter

180 degrees and remove the other

plug. Do not attempt to turn the con-

verter with a wrench on the converter

stud nuts. If desired, the converter

may be drained after the unit has been

removed from the vehicle.

5.
Disconnect the fluid filler tube

from the transmission case. Discon-

nect the vacuum hose from the vacu-

um diaphragm unit and the tube from

the extension housing clip.

6. When the fluid has stopped

draining from the transmission and

converter, remove the flywheel to con-

verter nuts and flat washers. Install

the drain plugs in the converter and

torque to specifications. Install the

converter housing front plate to hold

the converter in place when the trans-

mission is removed.

7.
Disconnect the starter cables

from the starter and remove the start-

er.

8. Disconnect the oil cooler lines

from the transmission. Remove the

transmission vent tube.

9. Disconnect the downshift linkage

from the transmission.

10.
Disconnect the selector rod from

the transmission manual lever with

T67P-7341-A.

11.
Disconnect the speedometer

cable from the extension housing, and

remove the driveshaft.
12.
Support the transmission on a

stand. Remove the engine rear support

to transmission bolts, and raise the

transmission slightly to take the

weight off the cross member. Remove

the cross member. Support the rear

part of the engine.

13.
Remove the remaining convert-

er housing to engine attaching bolts.

Move the assembly to the rear and

down to remove it.

INSTALLATION

1.
If the converter has been re-

moved from the converter housing,

carefully position the converter in the

housing, and then install the housing

lower front cover plate to prevent the

converter from slipping out of the

housing.

2.
Install the transmission vent

tube.
Rotate the converter until the

studs adjacent to the drain plugs are

in a vertical position.

3.
Rotate the flywheel as required

to align the drain plug holes with the

drain plugs in the converter. With the

transmission mounted on a support

stand, move the converter and trans-

mission assembly forward into posi-

tion, using care not to damage the fly-

wheel and the converter pilot.

4.
Install the converter lower

housing-to-engine bolts, then torque

the bolts to specification.

5.
Install the cross member.

6. Lower the transmission until the

extension housing rests on the cross

member, and then install the extension

housing-to-cross member bolts.

7.
The converter must rest squarely

against the flywheel. This indicates

that the converter pilot is not binding

in the engine crankshaft.

8. Install the converter attaching

nuts and flat washers. Install the ac-

cess plates.

9. Connect the oil cooler inlet and

outlet lines to the transmission case.

10.
Coat the front universal joint

yoke seal and spline with B8A-

19589-A lubricant, and install the

drive shaft.

11.
Connect the speedometer cable

at the transmission.

12.
Using tool T67P-7341-A install

a new grommet in the manual lever.

Then secure the manual selector rod

to the lever.

13.
Connect the downshift linkage

and bushing at the transmission

throttle lever.
14.
Install the starter motor.

15.
Connect the fluid filter tube to

the transmission case. Connect the

vacuum hose to the vacuum dia-

phragm unit and the tube to its clip.

16.
Lower the transmission support

stand. Then install the upper two con-

verter housing-to-engine bolts and

tighten them to specification.

17.
Lower the vehicle and fill the

transmission with transmission fluid,

following the recommended procedure.

18.
Check the transmission, con-

verter assembly, and fluid cooler lines

for fluid leaks, and then adjust the

manual and downshift linkages.

TRANSMISSION REPLACEMENT

WITHOUT CONVERTER—

FORD-METEOR

The frame construction of the con-

vertible will not permit the transmis-

sion to be moved rearward enough to

clear the turbine shaft from the con-

verter. For this reason, the converter

and transmission must be removed as

a unit from this model.

REMOVAL

1.
Raise the vehicle on a hoist.

2.
Drain the fluid from the trans-

mission.

3.
Disconnect the hose from the

vacuum diaphragm unit and the tube

from its clip. Disconnect the fluid fill-

er tube from the case.

4.
Remove the cover from the lower

front side of the converter housing.

5.
Remove one of the converter

drain plugs. Then rotate the converter

180 degrees and remove the other

plug. Do not attempt to turn the con-

verter with a wrench on the converter

stud nuts.

6. Disconnect the drive shaft from

the rear axle, and remove the drive

shaft.

7.
Disconnect the fluid cooler lines

from the transmission. Remove the

vent tube.

8. Disconnect the downshift linkage

at the transmission.

9. Disconnect the selector rod from

the transmission manual lever with

tool T67P-7341-A.

10.
Disconnect the speedometer

cable at the extension housing.

11.
Remove the two engine rear

support to transmission bolts.

12.
Position a transmission jack

under the transmission and raise it

slightly to take the weight off the

cross member.procarmanuals.com

07-04-05
C-6 Automatic Transmission

07-04-05

IN-VEHICLE ADJUSTMENTS AND REPAIRS

CONTROL LINKAGE

ADJUSTMENTS

The transmission control linkage

adjustments should be performed in

the order in which they appear in this

section of the manual.

THROTTLE AND

DOWNSHIFT LINKAGE

ADJUSTMENTS

Adjusting the throttle linkage is im-

portant to be certain the throttle and

kickdown systems are properly adjust-

ed. The kickdown system should come

in when the accelerator is pressed

through detent, and not before detent.

Refer to Group 10 for detailed

throttle and downshift linkage adjust-

ment procedures.

MANUAL LINKAGE

ADJUSTMENT

Column Shift

1.
Place the selector lever in the D

position tight against the stop.

2.
Loosen the shift rod adjusting

nut at point A (Fig. 4, 5, 6 or 7).

3.
Shift the manual lever at the

transmission into the D detent posi-

tion, third from the rear.

4.
Make sure that the selector lever

has not moved from the D stop; then,

tighten the nut at point A to 10-20 ft-

lbs.

5.
Check the transmission operation

for all selector lever detent positions.

Console Shift

1.
Position the transmission selec-

tor lever in the D position.

2.
Raise the vehicle and loosen the

manual lever shift rod retaining nut

(Fig. 8, 9 or 10). Move the transmis-

sion manual lever to the D position,

fourth detent position from the back

of the transmission.

3.
With the transmission selector

lever and manual lever in the D posi-

tions,
torque the retaining nut 10 to

20 ft-lbs.

4.
Check the operation of the trans-

mission in each selector lever position.
COLUMN SHIFT LEVER

SHIFT ROD

TRANSMISSION

MANUAL LEVER

D2031-A

FIG. 4—Manual Linkage—Column Shift—Ford-Mercury-Meteor

TRANSMISSION

MANUAL LEVER

FIG. 5—Manual Linkage—Column Shift—Fairlane-Montego

NEUTRAL START SWITCH

ADJUSTMENT-

CONSOLE SHIFT

On vehicles equipped with a

column-mounted neutral start switch,

refer to Part 7-1, Section 2, for the

adjustment procedures.

FORD, MERCURY

AND METEOR

1.
With the manual linkage proper-

ly adjusted, check the starter en-

gagement circuit in all positions. The

circuit must be open in all drive posi-

tions and closed only in park and neu-

tral.

2.
Remove the four screws and

plates securing the selector lever
D2032-M

the

handle to the lever. Remove

handle and detent control.

3.
Remove the two screws from the

rear of the console top panel. Pull the

panel back to unhook it from the

front of the console and remove the

panel.

4.
Loosen the two combination

starter neutral and back-up light

switch attaching screws (Fig. 11).

5.
Move the selector lever back and

forth until the gauge pin (No. 43 drill)

can be fully inserted into the gauge

pin holes (Fig. 11).

6. Place the transmission selector

lever firmly against the stop of the

neutral detent position.

7.
Slide the combination starter

neutral and back-up light switch for-

ward or rearward as required, untilprocarmanuals.com

07-04-06
C-6 Automatic Transmission
0704-06

TRANSMISSION

MANUAL LEVER

STUD-7B415

ENGAGE FLATS OF STUD IN SLOT OF

ROD BEFORE APPLYING TORQUE

FIG. 6—Manual Linkage—Column Shift—Lincoln Continental

INNER BRACKET-7C431

TRANSMISSION

MANUAL LEVER

ROD-7326

SHIFT ROD-7A024

ENGAGE FLAT OF STUD IN SLOT
OF

ROD BEFORE APPLYING TORQUE
POINT A

BRACKET ASSEMBLY-7C324

D1831-A

FIG.
7—Manual
Linkage—Column Shift—Thunderbird-Continental Mark
III

the switch lever contacts
the
selector

lever actuator.
If an
adjustment
can

not
be
made
by
rotating
the
switch,

loosen
the
actuator lever attaching

bolt
and
adjust
the
lever (Fig.
11).

8. Tighten
the
neutral start switch

attaching screws.
If the
actuator lever
was adjusted, tighten
the
actuator

lever bolt.

9. Turn
the
ignition
key to the

ACC position
and
place
the
selector

lever
in the
reverse position
and
check

the operation
of the
back-up lights.

Turn
the key off.
D2033-A

10.
Place
the
console
top
panel
on

the console
and
install
the
retaining

screws.

11.
Position
the
selector lever
de-

tent control
and
handle
on the
selector

lever
and
secure with
the
four plates

and attaching screws.

FAIRLANE-MONTEGO

1.
With
the
manual linkage proper-

ly adjusted, check
the
starter
en-

gagement circuit
in all
positions.
The

circuit must
be
open
in all
drive posi-

tions
and
closed only
in
park
and neu-

tral.

2.
Remove
the
selector lever handle

from
the
lever.

3.
Remove
the
trim panel from
the

top
of the
console.

4.
Remove
the
cover
and
dial indi-

cator
as an
assembly.

5.
Remove
the six
screws that
se-

cure
the
selector lever retainer
to the

selector lever housing. Lift
the
retainer

from
the
housing.

6. Loosen
the two
combination

starter neutral
and
back-up light

switch attaching screws (Fig.
12).

7.
Move
the
selector lever back
and

forth until
the
gauge
pin
(No.
43
drill)

can
be
fully inserted into
the
gauge

pin holes (Fig.
12).

8. Place
the
transmission selector

lever firmly against
the
stop
of the

neutral detent position.procarmanuals.com

07-04-09
C-6 Automatic Transmission
07-04-09

MUSTANG AND COUGAR

1.
With the manual lever properly

adjusted, loosen the two switch attach-

ing bolts (Fig. 13).

2.
With the transmission manual

lever in neutral, rotate the switch and

insert the gauge pin (No. 43 drill

shank end) into the gauge pin holes of

the switch. The gauge pin has to be

inserted to a full 31/64 inch into the

three holes of the switch (Fig. 13).

3.
Torque the two switch attaching

bolts to specification. Remove the

gauge pin from the switch.

4.
Check the operation of the

switch. The engine should start only

with the transmission selector lever in

Neutral and Park.

NEUTRAL START SWITCH

REPLACEMENT—CONSOLE

SHIFT

On vehicles equipped with a

column-mounted neutral start switch,

refer to Part 7-1, Section 2, for the

replacement procedures.

FORD, MERCURY

AND METEOR

1.
Remove the four screws and

plates securing the selector lever

handle to the lever. Remove the

handle and detent control.

2.
Remove the two screws from the

rear of the console top panel. Pull the

panel back to unhook it from the

front of the console and remove the

panel.

3.
Remove the two screws securing

the dial indicator assembly to the se-

lector lever housing and remove the

indicator assembly.

4.
Disconnect the neutral start

switch wires at the plug connector.

Remove the wires from under the re-

taining clip.

5.
Remove the two screws securing

the neutral start switch to the selector

lever housing and remove the switch

(Fig. 11).

6. Position the neutral start switch

to the selector lever housing and in-

stall the two attaching screws.

7.
Adjust the neutral start switch as

outlined under the Neutral Start

Switch Adjustment procedures in this

section.

8. Connect the neutral start switch

Wires to the plug connector. Position

the wires in the retaining clip and

close the clip.

9. Place the console top panel on

the console and install the retaining

screws.
NEUTRAL START

SWITCH

D1459-A

FIG. 73—Neutral Start Switch

Adjustment—Console Shift—

Mustang and Cougar

10.
Position the selector lever de-

tent control and handle on the selector

lever and secure with the four plates

and attaching screws.

FAIRLANE AND MONTEGO

1.
Remove the selector lever handle

from the lever.

2.
Remove the trim panel from the

top of the console.

3.
Remove the cover and dial indi-

cator as an assembly.

4.
Remove the four screws that se-

cure the selector lever retainer to the

selector lever housing. Lift the retainer

from the housing.

5.
Remove the two screws securing

the neutral start switch to the selector

lever housing. Disconnect the neutral

start switch wires at the plug connec-

tor and remove the switch.

6. Position the neutral start switch

to the selector lever housing and in-

stall the two attaching screws.

7.
With the selector lever in neu-

tral,
move the selector lever back and

forth until the gauge pin (No. 43 drill)

can be fully inserted into the gauge

pin holes (Fig. 12).

8. Place the transmission selector

lever firmly against the stop of the

neutral detent position.

9. Slide the combination starter

neutral and back-up light switch for-

ward or rearward as required, until

the switch actuating lever contacts the

selector lever.

10.
Tighten the switch attaching

screws and remove the gauge pin.

11.
Connect the neutral start switch

wires to the plug connector and check

for starting in the park position.
12.
Position the selector lever re-

tainer to the selector lever housing.

Install the attaching screws.

13.
Install the cover and dial indi-

cator.

14.
Install the trim panel on the top

of the console. Install the selector

lever handle.

MUSTANG AND COUGAR

1.
Remove the downshift linkage

rod from the transmission downshift

lever.

2.
Apply penetrating oil to the

downshift lever shaft and nut. Remove

the transmission downshift outer lever

retaining nut and lever (Fig. 13).

3.
Remove the two neutral start

switch attaching bolts.

4.
Disconnect the multiple wire

connector. Remove the neutral switch

from the transmission.

5.
Install the neutral start switch on

the transmission. Install the two at-

taching bolts.

6. With the transmission manual

lever in neutral, rotate the switch and

install gauge pin (No. 43 drill) into

the gauge pin hole (Fig. 13).

7.
Tighten the switch attaching

bolts to specification and remove the

gauge pin.

8. Install the outer downshift lever

and attaching nut, and torque the nut

to specification. Install the downshift

linkage rod to the downshift lever.

9. Install the switch wires. Connect

the wire multiple connector. Check

the operation of the switch in each de-

tent position. The engine should start

only with the transmission selector

lever in N (neutral) and P (park).

SELECTOR LEVER

REPLACEMENT-

CONSOLE SHIFT

FORD, MERCURY

AND METEOR

1.
Raise the vehicle and disconnect

the link assembly from the selector

lever arm (Fig. 8).

2.
Lower the vehicle. Remove the

four screws and plates securing the se-

lector lever handle to the lever. Re-

move the handle and detent control.

3.
Remove the two screws from the

rear of the console top panel. Pull the

panel back to unhook it from the

front of the console and remove the

panel.

4.
Disconnect the neutral start

switch wires at the plug connector.

Disconnect the bulb socket from the

quadrant.procarmanuals.com