1969 FORD MUSTANG stop start

07-04-15
C-6
Automatic Transmission
07-04-15

port attaching nuts and remove the

nuts.
Lift the crossmember from the

frame side supports.

19.
Remove the bolts that attach

the engine rear support to the exten-

sion housing and remove the support.

20.
Lower the transmission, then

disconnect the fluid cooler lines from

the transmission case.

21.
Secure the transmission to the

jack with a chain.

22.
Remove the six bolts that at-

tach the converter housing to the cyl-

inder block.

23.
Move the jack rearward until

the transmission clears the engine,

then tip it forward to provide clear-

ance. Lower the transmission and re-

move it from under the vehicle.

24.
Remove the converter from the

transmission. Mount the transmission

in a holding fixture if repairs are nec-

essary.

INSTALLATION—FAIRLANE,

MONTEGO,
MUSTANG

AND COUGAR

1. Mount the transmission in a

transmission jack and secure it with a

safety chain.

2.
Install the converter on the front

pump.

3.
Rotate the flywheel so that the

drain plug holes are in a vertical posi-

tion. Rotate the converter so that the

drain plugs are in the same relative

position as the drain plug holes in the

flywheel.

4.
Roll the transmission into posi-

tion under the vehicle and raise it to

alignment with the engine. Move it

forward until the converter housing

contacts the cylinder block. Install

and torque the converter-to-cylinder

block attaching bolts.

5.
Remove the jack safety chain

from the transmission.

6. Connect the two fluid cooler

lines to the fittings in the transmission

case.

7.
Secure the engine rear support to

the extension housing with the attach-

ing bolts. Torque the bolts to specifi-

cation.

8. Position the crossmember on the

frame side supports and install and

tighten the attaching nuts to specifica-

tion. Install cotter Dins to retain the

nuts.

9. Remove the transmission jack

from under the vehicle. Install and

torque the engine rear support-

to-crossmember attaching nuts.

10.
Install the exhaust system on

Mustang and Cougar.
11.
Install the converter-to-flywheel

attaching nuts and torque them to

specifications. Tighten the drain plugs

to specification.

12.
Secure the converter drain plug

access cover to the lower end of the

converter housing with the attaching

bolts.

13.
Install a new O-ring on the

lower end of the fluid filler tube. Dip

the O-ring in clean automatic trans-

mission fluid and insert the filler tube

in the transmission case.

14.
Secure the starter to the con-

verter housing. Connect the cable to

the terminal on the starter.

15.
Connect the speedometer cable

to the extension housing.

16.
Connect the shift rod to the

manual lever at the transmission. On

a column shift, use tool T67P-7341-A

and install a new grommet in the

manual lever. Then, secure the manual

selector rod to the lever.

17.
Connect the downshift rod to

the lever on the transmission. Adjust

the rod.

18.
Remove the tool from the ex-

tension housing and install the drive

shaft.

19.
Lower the vehicle.

20.
Working from the engine com-

partment, secure the fluid filler tube

to the rear of the right cylinder head

with the attaching bolt.

21.
On Mustang and Cougar, con-

nect the neutral switch wires to the

harness. Secure the wires to the dash

with the retaining clip.

22.
Fill the transmission with the

specified lubricant as detailed in Part

7-1.

REMOVAL—THUNDERBIRD

1. Working from the engine com-

partment, remove the fluid filler tube

bracket attaching screw that secures it

to the rear of the right cylinder head.

Lift the tube and dipstick from the

transmission.

2.
Remove the starting motor upper

attaching bolt using a long extension.

3.
Remove the two converter hous-

ing upper attaching bolts.

4.
Raise the vehicle on a hoist or

stands.

5.
Remove the dust shield from the

front lower end of the converter hous-

ing.

6. Crank the engine until one of the

converter drain plugs is accessible.

Then, remove the plug.

7.
Crank the engine until the other

plug is at the bottom. Place a drain

pan to catch the fluid, then remove

the pan and allow the fluid to drain.
8. Remove the drive shaft.

9. Remove the frame side rail sup-

port brace attaching bolts and remove

the brace.

10.
After the fluid has been drained

from the converter, install the plug.

11.
Place the drain pan under the

transmission pan and loosen the at-

taching bolts and allow the fluid to

drain. Finally remove all of the pan

attaching bolts except two, to allow

the oil to further drain. After the fluid

has drained, install two bolts on the

opposite side of the pan to temporari-

ly hold it in place.

12.
Remove the converter-

to-flywheel attaching nuts.

13.
Disconnect the downshift link-

age from the transmission downshift

lever.

14.
Using tool T67P-7341-A, re-

move the selector rod from the manu-

al lever.

15.
Remove the two screws that at-

tach the shift rod bellcrank bracket to

the converter housing and remove the

bracket.

16.
Disconnect the vacuum dia-

phragm hose from the upper end of

the vacuum tube.

17.
Disconnect the speedometer

cable from the extension housing and

place it to one side.

18.
Remove the starting motor two

lower attaching bolts and place the

motor to one side.

19.
Disconnect the two oil cooler

lines from the right side of the trans-

mission.

20.
Disconnect the muffler inlet

pipes at the exhaust manifolds and

allow the pipes to hang.

21.
Remove the vibration absorber

from the extension housing.

22.
Remove the two engine rear

support-to-extension housing attaching

bolts.

23.
Place a transmission jack under

the transmission and raise it just

enough to remove the weight from the

support.

24.
Remove the two support attach-

ing bolts and remove the support.

25.
Lower the jack just enough to

remove the weight.

26.
Remove the four remaining

converter housing-to-cylinder block at-

taching bolts and the accelerator link-

age stop from the left side of the

housing.

27.
Carefully lower the transmis-

sion and remove it from under the ve-

hicle.

28.
Remove the converter and

mount the transmission in a holding

fixture.procarmanuals.com

07-04-16
C-6 Automatic Transmission

07-04-16

INSTALLATION—

THUNDERBIRD

1.
Torque the two converter drain

plugs to specification.

2.
Install the converter on the sta-

tor support.

3.
Secure the transmission on a

transmission jack.

4.
Rotate the converter so that the

studs and drain plugs are in alignment

with their holes in the flywheel.

5.
Move the transmission toward

the cylinder block until they contact

each other. Install and torque the at-

taching bolts to specification. Before

tightening the center bolt on the left

side,
make sure that the accelerator

linkage stop bracket is properly posi-

tioned so that the left upper bolt may

be installed later.

6. Connect the fluid cooler lines to

their fittings on the right side of the

transmission.

7.
Raise the transmission and in-

stall the engine rear support and tor-

que the bolts to specification. Make

sure that the hand brake equalizer is

positioned properly.

8. Lower the transmission and re-

move the jack.

9. Install the engine rear support-

to-extension housing attaching bolts.

10.
Install the drive shaft.

11.
Connect the speedometer cable

to the extension housing.

12.
Position the starting motor on

the converter housing and secure it

with the two lower bolts.

13.
Install the torque converter-

to-flywheel attaching nuts and torque

them to specification.

14.
Install the converter housing

dust shield.

15.
Secure the frame side rail sup-

port brace with the attaching bolts

and lock washers. Torque the bolts to

specification.

16.
Connect the downshift rod to

the transmission downshift lever.

17.
Connect the vacuum diaphragm

hose to the upper end of the vacuum

tube.

18.
Using Tool T67P-7341-A, in-

stall a new grommet in the manual

lever. Then, secure the manual selec-

tor rod to the lever.

19.
Position the vibration absorber

to the transmission extension housing

and secure it with the three attaching

bolts.

20.
Connect the muffler inlet pipes

to the exhaust manifolds.

21.
Lower the vehicle and install

the two converter housing upper bolts

and torque them to specification.
22.
Install the starting motor upper

bolt.

23.
Place a new O-ring on the end

of the fluid filler tube and insert it in

the transmission case. Secure the tube

to the rear of the right cylinder head

with the attaching screw and lock

washer.

24.
Fill the transmission to the

proper level with the specified fluids.

25.
Adjust the manual and throttle

linkage as required.

REMOVAL-

CONTINENTAL MARK III

1.
Working from the engine com-

partment, lift the fluid filler tube dio-

stick from the transmission.

2.
Raise the vehicle on a hoist or

stands.

3.
Remove the dust shield from the

front lower end of the converter hous-

ing.

4.
Crank the engine until one of the

converter drain plugs is accessible.

Then, remove the plug.

5.
Crank the engine until the other

plug is at the bottom. Place a drain

pan to catch the fluid, then remove

the pan and allow the fluid to drain.

6. Remove the driveshaft.

7.
Remove the frame side rail sup-

port brace attaching bolts and remove

the brace.

8. After the fluid has been drained

from the converter, install the plug.

9. Place the drain pan under the

transmission pan and loosen the at-

taching bolts and allow the fluid to

drain. Finally remove all of the pan

attaching bolts except two, to allow

the oil to further drain. After the fluid

has drained, install two bolts on the

opposite side of the pan to temporari-

ly hold it in place.

10.
Remove the. converter-

to-flywheel attaching nuts.

11.
Disconnect the downshift link-

age from the transmission downshift

lever.

12.
Using tool T67P-7341-A, re-

move the selector rod from the manu-

al lever.

13.
Remove the two screws that at-

tach the shift rod bellcrank bracket to

the converter housing and remove the

bracket.

14.
Disconnect the vacuum dia-

phragm hose at the transmission.

15.
Disconnect the speedometer

cable from the extension housing and

place it to one side.

16.
Remove the two idler arm

bracket retaining bolts at the frame

side rail and allow the linkage to

hang.
17.
Disconnect the starter cable

from the terminal on the starter. Re-

move the starter attaching bolts and

remove it from the housing.

18.
Remove the clip securing the oil

cooler lines to the support bracket.

19.
Disconnect the two oil cooler

lines from the right side of the trans-

mission.

20.
Disconnect the muffler inlet

pipes at the exhaust manifolds and

allow the pipes to hang.

21.
Remove the vibration absorber

from the extension housing.

22.
Remove the engine rear support

to extension housing attaching bolts.

23.
Place a transmission jack under

the transmission and raise it just

enough to remove the weight from the

support.

24.
Remove the two support attach-

ing bolts and remove the support.

25.
Lower the jack and secure the

transmission to the jack with a safety

chain.

26.
Remove the bolt that secures

the filler tube to the rear of the right

cylinder head and lift the tube from

the transmission case.

27.
Remove the six converter

housing-to-cylinder block attaching

bolts.

28.
Carefully lower the transmis-

sion and remove it from under the ve-

hicle.

29.
Remove the converter and

mount the transmission in a holding

fixture.

INSTALLATION—

CONTINENTAL MARK III

1.
Torque the two converter drain

plugs to specification.

2.
Install the converter on the sta-

tor support.

3.
Secure the transmission on a

transmission jack.

4.
Rotate the converter so that the

studs and drain plugs are in alignment

with their holes in the flywheel.

5.
Move the transmission toward

the cylinder block until they contact

each other. Install and torque the at-

taching bolts to specification

6. Remove the jack safety chain

from the transmission.

7.
Connect the fluid cooler lines to

their fittings on the right side of the

transmission.

8. Install a new O-ring on the lower

end of the fluid filler tube. Dip the

O-ring in clean automatic transmis-

sion fluid and insert the tube in the

transmission case. Install the attach-

ing bolt.procarmanuals.com