1969 FORD MUSTANG seat adjustment

04-02-22

Rear Axle — Removable Carrier Type
04-02-22

Too/-T59L-4204-A

or
44211

and
44211-A

EH92-C

FIG. 56—Checking Differential

Torque

High Torque

a. Insufficient lubricant on the

clutch plates.

b.
A clutch plate wedged in be-

tween the case halves.

c. An improperly centered Belleville

spring.

Low Torque

a. Weak Belleville spring.
b.
Improper amount of clutch

plates installed.

Under no circumstances should the

Belleville spring be ground down to

reduce torque. The torque required to

keep the side gear turning with new

clutch plates is 155 to 195 ft-lbs. On

reused clutch plates, the torque re-

quired is 75 ft-lbs minimun.

7.
If the differential bearings have

been removed, press them on as

shown in Figs. 49 and 50.

8. Install the side bearings on the

differential case, and install the case

in the carrier as described in steps 7

through 16 under Assembly and In-

stallation of Conventional Differential

Case. Adjust and check backlash be-

tween the ring gear and pinion as di-

rected under Differential Bearing Pre-

load Adjustments.

ASSEMBLY OF

TRACTION-LOK

DIFFERENTIAL CASE

1.
Lubricate all parts with Ford

Hypoid Lubricant (Ford Part No.

C6AZ-19580-C), during assembly of

differential.

2.
Mount the differential case in a

soft jawed vise and place a side gear

thrust washer and side gear in the

counterbore of the case.

CENTER BLOCK

PRELOAD SPRINGS

PRELOAD PLATE

PINION GEAR

DIFFERENTIAL CASE

E1893-
A

. 57—Center Block and Pre-Load Springs Installation
3.
Install the pinion thrust washers

and place the pinion gears on the side

gear; aligning the holes in the washers

and gears with the holes in the case.

4.
Install the center block so that

the shaft holes are aligned with the

holes in the pinion gears and case.

The center block has two machined

sides and two rough sides.

5.
With a brass drift, drive in the

long pinion shaft from the outside of

the case aligning the lock pin holes in

the shaft with the holes in the case.

The center block should be positioned

so the long shaft is driven through the

rough side and short shafts driven

through the machined side (Fig. 57).

6. With a suitable drift, install the

shaft lock pins. Make sure the pinion

and side gears move freely.

7.
Place the four pre-load springs in

the holes provided in the center block.

8. Position a pre-load plate over the

four springs, making sure the springs

are properly seated. The pre-load

plate straddles the center block over

its narrower or machined width.

9. Mount the differential cover in a

soft jawed vise or holding fixture.

10.
Insert shim(s) of 0.050 total

thickness in the cover cavity.

11.
Install the composite plate (fric-

tion material on one side and steel on

the opposite) on the back side of the

clutch hub with the friction material

against the hub; next, install a friction

plate, then steel, friction, stee, fric-

tion, steel, friction, and lastily a steel

plate (Figures 3 and 58). When new

clutch plates are used, soak the plates

in Ford Hypoid Lubricant (Ford Part

No.
C6AZ-19580-C), or equivalent lu-

bricant, for approximately 30 minutes

before installation.

12.
Place the clutch hub with the

clutch plates into the clutch ear cavi-

ties in the differential cover. Make

sure that the splines on the last fric-

ion plate are engaged on the hub.

13.
Obtain locally a 5/8 inch x

2 1/2 inch or 9/16 inch x 2 1/2

inch bolt, nut and two I 1/2 inch

outside diameter flat washers approx.

1/8 inch in thickness. These parts are

required to compress the clutch pack

in order to obtain the proper shim

selection.

Install a flat washer on the bolt,

and place the bolt through the clutch

hub.
Hold the bolt in position and

turn the cover over. Place a flat wash-

er on the bolt and then install the nut.

Be sure the washers are centered, and

torque the nut 10 to 15 ft-lbs (Fig.

59).

14.
Place the shim template tool

(Ford Tool No. T68P-4946-A) in the

clutch hub. Some clearance should beprocarmanuals.com

04-03-11
Rear Axles — Integral Carrier Type

04-03-11

bores so that they just contact the

bearing cups.

14.
Carefully position the bearing

caps on the carrier casting. Match the

marks made when the caps were re-

moved.

15.
Install the bearing cap bolts

and lockwashers. As the bolts are

tightened, turn the adjusting nut with

the tool shown in Fig. 26.

16.
If the adjusting nuts do not turn
freely as the cap bolts are tightened,

remove the bearing caps and again in-

spect for damaged threads or incor-

rectly positioned caps. Tightening the

bolts to the specified torcfue is done to

be sure that the cups and adjusting

nuts are seated. Loosen the cap bolts,

and torque them to only 5 ft-lbs be-

fore making adjustments. Refer to

Part 4-1 for backlash and bearing pre-

load adjustment procedures.
LIMITED-SLIP DIFFERENTIAL

For integral carrier limited-slip dif-

ferentials see the repair procedures for

removable carrier limited-slip differen-

tials,
Part 4-2. These procedures are

good for the differential case only.

When the limited slip differential case

has been repaired replace the case

using the procedure for the conven-

tional intergral carrier differendal case

in this part.procarmanuals.com

04-04-10
Rear Axle — Ford Light-Duty (WER)

04-04-10

the differential case and ring gear as-

sembly in the carrier without regard

to the matching of any particular gear

teeth.

12.
Slide the case assembly along

the bores until a slight amount of

backlash is felt between the gear teeth.

Hold the differential case in place.

13.
Set the adjusting nuts in the

bores so that they just contact the

bearing cups.

14.
Carefully position the bearing

caps on the carrier casting. Match the

marks made when the caps were re-

moved (Fig. 21).

15.
Install the bearing cap bolts

and lockwashers. As the bolts are

tightened, turn the adjusting nut with

the tool shown in Fig. 21.

16.
If the adjusting nuts do not turn

freely as the cap bolts are tightened,

remove the bearing caps and again in-

spect for damaged threads or incor-

rectly positioned caps. Tightening the

bolts to the specified torque is done to

be sure that the cups and adjusting
.BEARING CAP IDENTIFICATION-j

MARKS
A

T57L-4067-A

E 1583-A

27—Bearing Cap Installation

nuts are seated. Loosen the cap bolts,

and torque them to only 5 ft-)bs be-

fore making adjustments. Refer to

part 4-1, Section 2 of this shop manu-

al for backlash and bearing preload

adjustment procedures.

17.
Clean the marking compound

from the gear teeth.

18.
Install both side bearing adjust-

ing nut locks (bolts) and torque them

to specification.
19.
Install the differential pinion

side gears and thrust washers.

20.
Install the rear wheel bearings

seals,
rear axle shafts, wheels and tires

and the axle carrier cover as outlined

under Part 4-3, Section 2, Rear Axle

Shaft, Wheel Bearing and Oil Seal

Replacement, Steps 10 through 19.

21.
Raise the axle all the way up.

Rdnove the safety support stands.

22.
Connect the track bar to the

mounting stud. Install the washer and

retaining nut, and torque the nut to

specification.

23.
Remove the oil seal replacer

tool from the transmission extension

housing. Install the front end of the

drive shaft on the transmission.output

shaft. Align the scribe marks on the

cups,
flange and drive shaft and con-

nect the rear end of the drive shaft to

the axle U-joint flange. Torque the re-

taining bolts to specification.

24.
Lower the vehicle.procarmanuals.com

05-03-03
Clutch
05-03-03

CLUTCH PEDAL

ADJUSTMENTS

Adjust
the
clutch pedal free travel

whenever
the
clutch does
not
disen-

gage properly,
or
when
new
clutch

parts
are
installed. Improper adjust-

ment
of the
clutch pedal
is one of the

most frequent causes
of
clutch failure

and
can be a
contributing factor
in

some transmission failures.

FREE TRAVEL

1.
Disconnect
the
clutch return

spring from
the
release lever.

2.
Loosen
the
release lever
rod

locknut
and
adjusting
nut
(Figs.
1, 2

and
3).

3.
Move
the
clutch release lever

rearward until
the
release bearing

lightly contacts
the
clutch pressure

plate release fingers.

4.
Adjust
the rod
length until
the

rod seats
in the
release lever pocket.

5.
Insert
the
specified feeler gauge

between
the
adjusting
nut and the

swivel sleeve. Then tighten
the
adjust-

ing
nut
against
the
gauge finger tight.

6. Tighten
the
locknut against
the

adjusting
nut,
being careful
not to di-

sturb
the
adjustment. Torque
the
lock-

nut
to
specification
and
remove
the

feeler gauge.

7.
Install
the
clutch return spring.

8. Check
the
free travel
at the
pedal

for conformance
to
specification.
Re-
adjust
if
necessary.

9.
As a
final check, measure
the

pedal free travel with
the
transmission

in neutral
and the
engine running
at

about 3000
rpm. If the
pedal free

travel
at
this speed
is not a
minimum

of
1/2
inch, readjust
the
clutch pedal

free travel. Otherwise,
the
release
fin-

gers
may
contact
the
release bearing

continuously, resulting
in
premature

bearing
and
clutch failure. Free travel

must
be
exactly
to
specification.

CLUTCH ASSIST

SPRING REPLACEMENT

(FAIRLANE, FALCON,

MONTEGO)

1.
Remove
the
cotter
pin
from
the

clutch
rod at the
clutch pedal lever
as-

sembly inside
the
passenger compart-

ment.

2.
Grasp
the
clutch pedal lever

firmly
to
prevent slipping
and
remove

the clutch
rod
from
the
lever. Allow

the clutch pedal lever
to
rest
on the

floor panel.

3.
Remove
the
forward bolt secur-

ing
the
assist spring bracket
to the

brake pedal bracket
and
loosen
the

rear bolt
two or
three turns.
Do not

remove
the
rear bolt.

4.
Grasp
the
assist spring bracket

with pliers
and
rotate upward until
the

spring
can be
separated from
the

bracket.

BRAKE PEDAL

BRACKET

CLUTCH ASSIST SPRING

BRACKET
-
7535

CLUTCH PEDAL

7519
5.
Position
the
assist spring
in the

clutch pedal spring bracket
and the

assist spring bracket. Rotate
the

spring bracket downward until
the

forward bolt holes
in the
assist spring

bracket line
up
with
the
holes
in the

brake pedal bracket
(Fig. 4).

6. Install
the
forward bolt retaining

the assist spring bracket
to the
brake

pedal bracket
and
torque
the
forward

and rear bolts
to
specification.

7.
Install
the
clutch
rod to the

clutch pedal lever
and
insert
the
cotter

pin.

CLUTCH PEDAL, PEDAL

ASSIST SPRING AND/OR

BUSHING REMOVAL

AND INSTALLATION

FORD, MERCURY,

METEOR

1.
Remove
the pin
that secures
the

clutch pedal-to-equalizer
rod to the

clutch pedal.

2.
Grasp
the
clutch pecal lever

firmly
to
prevent slipping
and
remove

the clutch
rod
from
the
lever. Allow

the clutch pedal lever
to
rest
on the

floor.

3.
Loosen
the
lower bolt securing

the assist spring bracket
to the
pedal

support bracket
two or
three turns.

Then, remove
the
upper bolt from
the

bracket.
Do not
remove
the
lower

bolt.

4.
Grasp
the
assist spring bracket

with pliers
and
rotate
it
counterclock-

wise until
the
spring
is
free
(Fig 5).

5.
Remove
the
retaining ring from

the
end of the
clutch pedal shaft. Then

remove
the
shaft, bushings
and
clutch

pedal from
the
support.

6. Remove
the
bushings from
the

pedal shaft
and
pedal support
and

transfer
the
rubber pedal
pad.

7.
After lubricating
the
pedal shaft

ASSIST SPRING

LOWER BOLT

ASSIST SPRING BRACKET-

UPPER
BOL"

C 1769-B

FIG. 4—Clutch Pedal Assembly
—
Fairlane, Montego, Falcon
C2058-A

;. 5—Removing Clutch Assist

Spring
—
Ford,
Mercury and Meteorprocarmanuals.com

06-02-03
Ford Design Three Speed Transmission

06-02-03

STOP
PIN

GROMMET

Tool -
T67P.7347.A

GROMMET

LEVER

CONTROL ROD REMOVAL
^S.
GROMMET INSTALLATION

SET STOP PIN SO THAT THE GROMMET

Tool
-
T67P.734LA
AND
SHIFT ROD ARE PROPERLY SEATED
OMMET—^

SEATED
\

CONTROL ROD INSTALLATION

CONTROL ROD

STOP
PIN

FIG. 4—Removing
or
Installing Shift Linkage Grommet

GEAR SHIFT LINKAGE

ADJUSTMENT—FLOOR MOUNTED

1.
Loosen
the
three shift linkage

adjustment nuts. Install
a 1/4
inch
di-

ameter alignment pin through the con-

trol bracket and lever alignment holes

shown
in Fig. 18.

2.
Tighten
the
three linkage adjust-

ment nuts
and
then remove
the
align-

ment
pin.

3.
Check
the
gear shift lever
for a

smooth crossover.

COLUMN-MOUNTED

SHIFT LINKAGE

GROMMET REMOVAL
AND

INSTALLATION

The column-mounted shift lever
as-
sembly incorporates
an oil
impregnat-

ed plastic grommet
in the
end
of
each

lever
arm. A
special tool T67P-

7341-A
is
required
to
install the grom-

met
in the
shift lever,
and to
install

the shift linkage
rod
into
the
grom-

met. Remove
and
install
the
grommet

as follows:

1.
Place
the
lower
jaw of the
tool

between
the
shift lever
and the
shift

rod.
Position
the
stop
pin
against
the

end
of the
shift
rod
(Fig.
4)
and force

the
rod out of the
grommet. Remove

the grommet from
the
shift lever
by

cutting
off the
large shoulder with
a

sharp knife. The groin met must
be re-

moved from
the
shift lever
and a new

one installed each rime
'he rod is
dis-

connected.

2.
Before installing
a
new grommet,
C 2090-A

adjust
the
stop
pin as
necessary
to

properly install
the
grommet and coat

the outside
of
the grommet with lubri-

cant. Then, place
the
grommet
on the

stop
pin and
force
it
into
the
shift

lever hole. Turn
the
grommeit several

times
to be
sure
it is
properly seated.

3.
Readjust
the
stop
pin to a
length

which
is
sufficient
to
install
the
shift

rod into
the
grommet
(Fig.
4).
If
the

pin height
is not
adjusted,
the
shift

rod
may be
pushed
too far
through

the grommet causing damage
to the

grommet retaining
lip.

4.
With
the pin
height properly
ad-

justed, position
the
shift
rod on the

tool
and
force
the rod
into
the
grom-

met until
the
groove
in the rod
seats

on
the
inner retaining
lip of
the grom-

met.

REMOVAL AND INSTALLATION

REMOVAL

1.
Raise
the
vehicle
on a
hoist.

2.
Mark
the
drive shaft
so
that
it

may
be
installed
in the
same relative

position. Disconnect
the
drive shaft

from
the
rear U-joint flange.

3.
Slide
the
front
of the
drive shaft
out
of the
transmission extension

housing
and off the
output shaft
In-

sert
the
tool shown
in (Fig. 2),
Part

6-1 into the extension housing
to
pre-

vent
the
lubricant from leaking
out of

the transmission.

4.
Remove
the cap
screw
and
lock

washer that secures
the
speedometer
cable retainer
to the
extension hous-

ing. Pull
the
speedometer cable
out of

the extension housing.

5.
On
vehicles equipped with
a

column-mounted gear shift selector,

remove
the
shift rods from
the
shift

levers
at
the transmission. On vehicles

equipped with
a
floor-mounted gearprocarmanuals.com

07-01-03

General Transmission Service

07-01-03

COMPONENT INDEX

FMX Transmission

REAR SUPPORT (FMX)

Inspection

SHIFT POINT CHECKS

STATOR ONE-WAY CLUTCH CHECK

STATOR TO IMPELLOR INTERFERENCE

CHECK

STATOR TO TURBINE INTERFERENCE

CHECK

TRANSMISSION CLEANING

TURBINE AND STATOR END PLAY

CHECK

VACUUM DIAPHRAGM ADJUSTMENT

Altitude Compensating Type

Non-Altitude Compensating Type

VACUUM UNIT CHECK

Altitude Compensating Type

Non-Altitude Compensating Type
MODEL APPLICATION
All
Models

01-06

01-12

01-12

01-12

01-11

01-12
Ford
01-17

01-16

N/A

01-08

N/A

01-05
Mercury
N/A

N/A

N/A

01-08

N/A

01-05
Meteor
01-17

01-16

N/A

01-08

N/A

01-05
Cougar
01-17

01-16

N/A

01-08

N/A

01-05
Fairlane
01-17

01-16

N/A

01-08

N/A

01-05
Falcon
N/A

N/A

N/A

01-08

N/A

01-05
Montego
01-17

01-16

N/A

01-08

N/A

01-05
Mustang
01-17

01-16

N/A

01-08

N/A

01-05
Lincoln-
Continental
N/A

N/A

01-09

N/A

01-06

N/A
Thunderbird
N/A

N/A

01-09

N/A

01-06

N/A
Continental-
Mark
III
N/A

N/A

01-09

N/A

01-06

N/A

A page number indicates that the item is for the vehicle listed at the head of the column.

N/A indicates that the item is not applicable to the vehicle listed.

Three different three-speed trans-

missions are used. The C4 Automatic,

C6 Automatic and the FMX Auto-

matic. Part 7-1 covers testing, com-
mon adjustments and repairs, and

cleaning and inspection for the three

types of transmissions. Where there
are differences in procedures or speci-

fications, the type of transmission af-

fected will be designated.

l
AUTOMATIC TRANSMISSION TESTS

When diagnosing transmission

problems, refer to the Ford Car and

Truck Diagnosis Manual for the de-

tailed information on the items that

could be causing the problem.

The following preliminary checks

should be made before proceeding

with other diagnosis checks.

TRANSMISSION FLUID LEVEL

CHECK

1.
Make sure that the vehicle is

standing level. Then firmly apply the

parking brake.

2.
Run the engine at normal idle

speed. If the transmission fluid is cold

run the engine at fast idle speed

(about 1200 rpm) until the fluid reach-

es its normal operating temperature.

When the fluid is warm, slow the en-

gine down to normal idle speed.

3.
On a vehicle equipped with a

vacuum brake release, disconnect the

release line and plug the end of the
line;
otherwise the parking brake will

not hold the transmission in any drive

position.

4.
Shift the selector lever through

all positions, and place the lever at P.

Do not turn off the engine during the

fluid level checks.

5.
Clean all dirt from the transmis-

sion fluid dipstick cap before remov-

ing the dipstick from the filler tube.

6. Pull the dipstick out of the tube,

wipe it clean, and push it all the way

back into the tube. Be sure it is prop-

erly seated.

7.
Pull the dipstick out of the tube

again, and check the fluid level. The

fluid level should be above the ADD

mark. If necessary, add enough fluid

to the transmission through the filler

tube to bring the level between the

ADD and FULL marks on the dip-

stick. Do not overfill the transmission.

Install the dipstick, making sure it is

fully seated in the tube.
8. Connect the vacuum brake re-

lease line if so equipped, and test it

for proper operation.

FLUID AERATION CHECK

A fluid level that is too high will

cause the fluid to become aerated:

Aerated fluid will cause low control

pressure, and the aerated fluid may be

forced out the vent.

Check the transmission fluid level.

Low fluid level can affect the opera-

tion of the transmission, and may in-

dicate fluid leaks that could cause

transmission damage.

TRANSMISSION FLUID

LEAKAGE CHECKS

Check the speedometer cable con-

nection at the transmission. Replace

the rubber seal if necessary.

Leakage at the oil pan gasket often

can be stopped by tightening the at-
procarmanuals.com

07-01-08
General Transmission Service

07-01-08

3.
Install the bench testing tool on

the transmission.

4.
Remove the
1/8-inch
pipe plug

at the transmission case. Turn the

front pump in a clockwise direction at

75-100 rpm until a regular flow of

transmission fluid leaves the hole in

the transmission case. This operation
bleeds the air from the pump.

5.
Install the pressure gauge (77820

or T57L-77820-A) as shown in Fig.

13.

PRESSURE TESTS

Turn the front pump at 75-100 rpm
and note the gauge readings. The

pressure readings on the bench test

must be within the limits as outlined

in Figure 13, for the engine idle check.

If pressure gauge readings are with-

in limits in all selector lever positions,

install the vacuum diaphragm control

rod unit.

COMMON ADJUSTMENTS AND REPAIRS

TRANSMISSION FLUID DRAIN

AND REFILL

Normal maintenance and lubrica-

tion requirements do not necessitate

periodic automatic transmission fluid

changes.

If a major repair, such as a clutch

band, bearing, etc., is required in the

transmission, it will have to be re-

moved for service. At this time the

converter, transmission cooler and

cooler lines must be thoroughly

flushed to remove any dirt.

When filling a dry transmission and

converter, install five quarts of fluid.

Start the engine, shift the selector

lever as outlined below, and check and

add fluid as necessary.

Following are the procedures for

partial drain and refill due to in-

vehicle repair operation.

C4 TRANSMISSION

1.
On PEA models, disconnect the

fluid filler tube from the transmission

oil pan to drain the fluid.

On PEB and PEE models, loosen

the pan attaching bolts to drain the

fluid from the transmission.

2.
When the fluid has stopped

draining from the transmission, re-

move and thoroughly clean the pan

and the screen. Discard the pan gas-

ket.

3.
Place a new gasket on the pan,

and install the pan on the transmis-

sion.

4.
On PEA models, connect the

filler tube to the pan and tighten the

fitting securely.

5.
Add three quarts of fluid to the

transmission through the filler tube.

6. Run the engine at idle speed for

about two minutes, and then run it at

fast idle speed (about 1200 rpm) until

it reaches it's normal operating temp-

erature. Do not race the engine.

7.
Shift the selector lever through

all the positions, place it at P, and

check the fluid level. The fluid level

should be above the ADD mark. If
necessary, add enough fluid io the

transmission to bring the level be-

tween the ADD and FULL marks on

che dipstick. Do not overfill the trans-

mission.

FMX OK C6

TRANSMISSION

1.
Raise the vehicle on a hoist or

jack stands.

2.
Place a drain pan under the

transmission.

3.
Loosen the pan attaching bolts

to drain the fluid from the transmis-

sion.

4.
After the fluid has drained to the

level of the pan flange, remove the

rest of the pan bolts working from the

rear and both sides of the pan to

allow it to drop and drain slowly.

5.
When the fluid has stopped

draining from the transmission, re-

move and thoroughly clean the pan

and the screen. Discard the pan gas-

ket.

6. Place a new gasket on the pan,

and install the pan on the transmis-

sion.

7.
Add three quarts of fluid to the

transmission through the filler tube.

8. Run the engine at idle speed for

about two minutes, and then run it at

fast idle speed (about 1200 rpm) until

it reaches normal operating tempera-

ture.
Do not race the engine.

9. Shift the selector lever through

all the positions, place it at P, and

check the fluid level. The fluid level

should be above the ADD mark. If

necessary, add enough fluid to the

transmission to bring the level be-

tween the ADD and FULL marks on

the dipstick. Do not overfill the trans-

mission.

OIL COOLER TUBE

REMOVAL AND INSTALLATION

When fluid leakage is found at the

oil cooler, the cooler must be re-

placed. Cooler replacement is de-

scribed in the Cooling System Section

of Group 11.
When one or more of the fluid

cooler steel tubes must be replaced,

each replacement tube must be fabri-

cated from the same size steel tubing

as the original line.

Using the old tube as a guide, bend

the new tube as required. Add the

necessary fittings, and install the tube.

After the fittings have been tight-

ened, add fluid as needed, and check

for fluid leaks.

VACUUM DIAPHRAGM

ADJUSTMENT NON-ALTITUDE

COMPENSATING TYPE

The C4 and C6 transmissions are

equipped with an adjustable vacuum

diaphragm assembly. A similar ad-

justable diaphragm has been released

for service with the FMX transmis-

sion. However, the FMX service dia-

phragm is not interchangeable with

that used on C4 and C6 models.

The vacuum diaphragm assembly

has an adjusting screw in the vacuum

hose connecting tube (Fig. 14).

SPRING

SEAT

THIS CLEARANCE CHANGED

BY ADJUSTING SCREW

D1830-A

FIG. 14—Adjustable Vacuum Unit

The inner end of the screw bears

against a plate which in turn bears

against the vacuum diaphragm spring.

All readings slightly high or all

readings slightly low may indicate the

vacuum unit needs adjustment to cor-

rect a particular shift condition.procarmanuals.com