1969 FORD MUSTANG oil pressure

03-13-08
Specifications
03-13-08

SPECIAL SERVICE TOOLS

Tool No.

T50T-100-A

T59L-100-B

T58L-101-A

T53L-200-A

T62L-201-A

OTC-462

T57L-500-A

T69L-1102-A

Tool 1175-AB

Tool 1175-AH

T56P-1217-A

T60K-1217-A

Tool 1217-J

Tool 1217-K

Tool
1217- L

Tool 1217-M

T65P-3000-A, D

T65P-3000-B, C, E, F

T57P-3006-A

T60K-3005-A

T62F-3006-A

Tool 3044-A

T54P-3044-A

T60K-3044-A

T65P-3044-A

Tool 3068

Tool 3069-AA

Tool
3069-
M

Tool 3290-C

T65P-3524-A

T66P-3553-A, B

T66P-3553-C

T65P-3548-A

T62F-3576-A

T64K-3576-A

T64K-3576-B

T65P-3576-A, B

T65P-3576-C

Tool 3583-J

T65P-3590-F

T67L-3600-A

T65P-3805-A

T63P-5310-A

T64K-5310-A, B

T66P-5310-A, B

T64N-5781-A

T64K-5781-B

Tool 6306-AG

T63L-8620-A

T63L-10300-B

T65P-10300-B

T56L-33610-D

T68L-33610-A

Tool 33623-D

T65P-3A537-A

T65P-3A537-B

T69P-3A674-A

T65P-3A733-A

T65T-3B177-A

T68P-3B586-A

T68P-3B592-A

T68P-3B592-B

T64B-3C716-A

T65P-3C732-A

T65P-3D517-A

T65P-3D525-A

T65P-3D525-B

T65P-3D526-A

T69P-3D608-A

T69P-3D608-B

T65P-3D642-A

T67P-3D739-A
Description

Slide Hammer-Long

Slide Hammer-Short

Puller Attachment

Handle Adapter

Input Shaft Seal Installer

Tie Rod Separator (Owatonna Tool Co.)

Bench Mounted Holding Fixture

Front Wheel Bearing Remover

Grease Seal Remover (Head Only)

Grease Seal Replacer

Front Hub Bearing Cup and Grease Seal Replacer

Front Hub Bearing Cup and Grease Seal Replacer

Front Hub Outer Bearing Cup Replacer

Front Hub Inner Bearing Cup Replacer

Front Hub Outer Bearing Cup Remover

Front Hub Inner Bearing Cup Remover

Adjusting Bars-Caster and Camber

Alignment Spacers

Spindle Ball Joint Remover Press

Spindle Ball Joint Press Adapter Screw

Spindle Ball Joint Press Adapter Screw

Front Suspension Upper Arm Bushing Remover

Front Suspension Upper and Lower Arm Overhaul Kit

Front Suspension Lower Arm Bushing Remover and Replacer

Upper Arm Bushing Overhaul Kit

Front Suspension Upper Arm Bushing Adapter

Front Suspension Lower Arm Bushing Remover

Lower Arm Bushings-Remover and Replacer Kit

Tie Rod Ball Ends and Control Valve Ball Stud Remover

Input Shaft Bearing Remover and Installer

Spanner Wrench

Spacer

Oil Line Connector Seal Installer

Sector Shaft Bushing Remover and Replacer

Sector Shaft Needle Bearings and Seal Remover and Replacer

Sector Shaft Needle Bearings and Seal Remover and Replacer Adapter

Sector Shaft Bushing Remover and Installer

Remover and Installer Adapter

Control Valve Bearing and Seal Remover and Replacer

Steering Pitman Arm Remover

Steering Wheel Remover

Ring Compressor-Rack Piston

Front Coil Spring Remover and Replacer

Adapters

Adapters

Rear Spring Front Bushing Remover and Installer

Rear Spring Bushing Adapter

Crankshaft Damper Remover and Power Steering Pump Sprocket Replacer

Bent Tension Gauge

Pulley Remover

Alternator Pulley Replacer

Pressure Testing Gauge Assembly

Bypass and Orifice Gauge

Pump Oil Seal Pilot

Bearing Preload Spanner Wrench

Adjuster Plug Seal Protector

Fixture Adapter Plate

Power Steering Pump Pulley Remover

Front Suspension Bushings Remover and Replacer

Pump Housing Hole Plugging Tool

Pump Shaft Seal Replacer

Pump Shaft Seal Protector

Insulator Remover and Replacer Socket

Lock Spring Installing Hook

Rack Piston Arbor

Adjuster Plug Bearing Remover and Installer

Thrust Bearing Retainer Installer Adapter

Adjuster Plug Seal Installer

Pin Straightness Checking Block

Pin Guide Support

Sector Shaft Seal Installer

Pivot Pin Removerprocarmanuals.com

04-02-13

Rear Axle
—
Removable Carrier Type
04-02-13

lower insulators. Torque
the
spring

clip nuts
to
specification.

2.
Place
the
brake backing plates
in

their normal position
on the
axle

housing.

3.
Install
new
axle shaft
oil
seals

with
the
tool shown
in Fig. 10.
Soak

the
new
seals
in
light weight engine
oil

(SAE
10) for 1/2
hour before install-

ing them. Installation without
use of

the proper tool will distort
the
seal

and cause leakage. Coat
the
outside
edges
of the new oil
seal with
a non-

hardening type
of
sealer such
as Per-

matex
No. 2 or its
equivalent.

4.
Install
the
axle shafts, brake

drums
and
wheels
as
outlined
in Sec-

tion
2.

5.
Attach
the
hydraulic brake line

T fitting
to the
axle housing,
and se-

cure
the
hydraulic brake line
in its re-

tainer
on the
axle housing.

6. Install vent tube
to
brake tube

junction
and
install vent hose
to
vent
tube.

7.
Raise
the
axle housing
and con-

nect
the
shock absorbers.

8. Connect
the
rear
end of the
drive

shaft
to the
axle U-joint flange, align-

ing
the
scribe marks made
on the

drive shaft
end
yoke
and the
axle
U-

joint flange.

9. Fill
the
axle with
the
proper

grade
and
amount
of
lubricant.

10.
Road test
the
vehicle.

MAJOR REPAIR OPERATIONS

DISASSEMBLY
OF

DIFFERENTIAL CARRIER

CONVENTIONAL

DIFFERENTIAL

A disassembled view
of the
rear

axle assembly
is
shown
in Fig. 17.

After mounting
the
carrier
in a

holding fixture, disassemble
the car-

rier
as
outlined
in the
following proce-

dures:

1.
Mark
one
differential bearing

cap
and the
mating bearing support

with punch marks
to
help position
the

parts properly during assembly
of the

carrier. Also, mark
one of the
bearing

adjusting nuts
and the
carrier with

AXLE SHAFT-4725
RETAINER RING-1100
scribe marks
for
proper location
dur-

ing assembly.

2.
Remove
the
adjusting
nut
locks,

bearing caps,
and
adjusting nuts. Then

lift
the
differential case assembly
out

of
the
carrier.

(Remove
the
bearing caps
by tap-

ping
the
caps lightly with
a
soft
mal-

let).

3.
Remove
the
differential bearings

with
the
tools shown
in Fig. 18.

4.
Mark
the
differential case, cover,

and ring gear
for
assembly
in the
orig-

inal position.

5.
Remove
the
bolts that attach
the

ring gear
to the
differential case. Press

the gear from
the
case
or tap it off

with
a
soft-faced hammer.

6. With
a
drift, drive
out the
differ-

AXLE HOUSING-4010

DIFFERENTIAL

PINION SHAFT-4211
ential pinion shaft lock
pin (Fig. 19),

and separate
the
2-piece differential

case.

7.
Drive
out the
pinion shaft with
a

brass drift
(Fig. 20).

8. Remove
the
gears
and
thrust

washers
(Fig. 48).

LIMITED-SLIP DIFFERENTIAL

1.
Remove
the
differential case

from
the
carrier
and
remove
the
bear-

ings from
the
differential case
in the

same manner
as the
conventional
dif-

ferential case.

2.
Place
the
differential case
in a

hydraulic press,
and
apply about
one

ton pressure across
the
case bearing

hubs while removing
the
ring gear
at-

FLAT WASHER (LIMITED SLIP ONLY)

DRIVE GEAR ATTACHING BOLT

DIFFERENTIAL CASE COVER -4206

DIFFERENTIAL PINION GEAR-4215

THRUST WASHER-4230

ADJUSTING NUT-4067

CARRIER HOUSING-4025

DRIVE PINION-4610
PINION BEARING

SPACER-4662

PINION FRONT

BEARING-4621

RING GEAR

PILOT BEARING-4A242

FIG. 17—Rear Axle Disassembled—Typical
PILOT BEARING

RETAINER-4627

PINION REAR

BEARING CUP-4616
DEFLECTOR-4859

PINION RETAINER-4668

SEAL-4676
FLANGE_4858
E1750-Aprocarmanuals.com

05-02-04
General Clutch Service

05-02-04

CLEANING AND INSPECTION

RELEASE BEARING

Wipe all oil and dirt off the release

bearing. The bearing is prelubricated

and should not be cleaned with sol-

vent.

Inspect the bearing retainer for

loose spring clips and rivets.

Inspect the release bearing assembly

for burrs which may cause the assem-

bly to drag on the transmission bear-

ing retainer. Any such burrs should be

cleaned up with fine crocus cloth. If

burrs are found, inspect the transmis-

sion input shaft bearing retainer for

evidence of scoring. Any scoring

should be polished out with crocus

cloth. Coat the bearing retainer with a

thin film of lithium-base grease

(C3VY-19586-A). Prior to release

bearing installation, apply a light film

of lithium base grease (C3VY-

19586-A) on both sides of the release

lever fork where it contacts the release

bearing hub and retaining springs.

Apply a light film of lithium base

grease (C3VY-19586-A) plate to the

release bearing surface that contacts

the pressure plate fingers. Carefully

fill the grease groove inside the bear-

ing hub with lithium base grease (no

polyethylene). Clean all excess grease

from the bore of the bearing hub. Ex-

cess grease will be forced onto the

spline by the transmission input shaft

bearing retainer and will contaminate

the clutch disc. Also, care must be

exercised when applying lubricants to

the release bearing, release bearing

hub and the release lever fork to avoid

excessive grease from contaminating

the clutch disc.

Hold the bearing inner race and ro-

tate the outer race while applying

pressure to it. If the bearing rotation

is rough or noisy, replace the bearing.

Most release bearing failures are

caused by improper clutch pedal ad-

justments. If the clutch linkage does

not have enough free travel, the re-

lease bearing will constantly touch the

release fingers and will spin whenever

the engine is running.

When installing a release bearing on

vehicles equipped with separate hub

and bearing, use the tool shown in

Fig. 5.

Release bearing failure can be

caused by the release lever contact

points being out of plane. Check the

wear on the release bearing assembly

where the release lever contacts it.

If one side of the assembly shows

more wear than the other, the release
lever is bent out of plane, or is not

centering on the bracket on the fly-

wheel housing.

Misalignment between the engine

and transmission can cause release

bearing failure. Other symptoms of

misalignment are transmission jump-

ing out of gear, especially third gear,

drive line vibration; excessive wear in

the pilot bushing, excessive clutch disc

spin time resulting in gear clash, and

excessive transmission gear wear.

PRESSURE PLATE AND COVER

Inspect the surface of the pressure

plate for burn marks, scores, or rid-

ges.
Generally, pressure plate resur-

facing is not recommended. However

minor burn marks, scores, or ridges

may be removed. During the resurfac-

ing process, the flatness of the pres-

sure plate must be maintained. If the

pressure plate is badly heat-checked or

deeply scored, replace the pressure

plate and cover assembly. Clean pres-

sure plate and flywheel surfaces with a

suitable solvent, such as alcohol to be

sure the surfaces are free from any oil

film. Do not use cleaners with petrole-

um base, and do not immerse the

pressure plate in the solvent.

Place the plate on the floor, being

careful not to score or scratch the sur-

face.
Force each individual finger

down, then release quickly. If the fin-

ger does not return quickly, a binding

condition is indicated, and the pres-

sure plate should be replaced.

The pressure plate should be lubri-

cated with a lithium-base grease be-

tween the driving lugs and the edges

of the pressure plate openings, as

shown in Fig. 6. Depress the pressure

plate fingers fully, apply the lubricant,

and then move the fingers up and

down until the lubricant is worked in.

Do not apply excessive lubricant.

CLUTCH DISC

Inspect the clutch disc facings for

oil or grease. Eliminate the source of

any oil or grease before replacing the

disc. An excessive amount of grease in

the pilot bushing or release bearing

hub will find its way to the disc fac-

ings.
Too much lubricant in the trans-

mission or a plugged transmission

vent will force the transmission lubri-

cant out the input shaft and onto the

disc facings. Also, rear main bearing

oil seal leaks or oil leaks from the fly-

wheel mounting bolts can contaminate

the clutch disc.
Inspect the clutch disc for worn or

loose facings. Check the disc for worn

or loose facings. Check the disc for

distortion and for loose rivets at the

hub.
Check for broken springs.

Springs loose enough to rattle will not

cause noise when the car is operating.

Replace the disc assembly if any of

these defects are present. Be especially

careful when installing a new disc to

avoid dropping it or contaminating it

with oil or grease.

PILOT BUSHING

Check the fit of the clutch pilot

bushing in the bore of the crankshaft.

The bushing is pressed into the

crankshaft and should not be loose.

Inspect the inner surface of the bush-

ing for wear or a bell-mouthed condi-

tion. If the bushing is worn or dam-

aged, replace the bushing with a new

service bearing. Refer to the applica-

ble engine for the replacement proce-

dure.

C 1785-A

FIG. 5—Installing Clutch Release

Bearing on Hub

PRESSURE PLATE

AND COVER

DRIVING

LUG
FLYWHEEL

C2048-A

FIG. 6—Pressure Plate Lubrication

Pointsprocarmanuals.com

05-03-06
Clutch

05-03-06

8. Remove the starter cable then

remove the starter motor from the fly-

wheel housing.

9. Remove the bolts that secure the

engine rear plate to the front lower

part of the flywheel housing.

10.
Remove the flywheel housing

lower cover (390 CID housing only).

11.
Remove the bolts that attach

the housing to the cylinder block.

12.
Move the housing back just far

enough to clear the pressure plate,

then move it to the right to free the

pivot from the clutch equalizer bar. Be

careful not to disturb the linkage and

assist spring.

13.
Loosen the six pressure plate

cover attaching bolts evenly to release

the spring tension. If the same pres-

sure plate and cover is to be installed

after the clutch is overhauled, mark

the cover and flywheel so that the

pressure plate can be installed in the

same position.

14.
Remove the pressure plate and

the clutch disc from the flywheel.

CLUTCH INSTALLATION

1.
Install the clutch release lever if

it was removed.

2.
Place the clutch disc, and pres-

sure plate assembly in position on the

flywheel. Start the cover attaching

bolts to hold the pieces in place, but

do not tighten them. Avoid touching

the clutch disc facing, dropping the

parts or contaminating them with oil

or grease as clutch chatter may result.

3.
Align the clutch disc with the

tool shown in Fig. 7, and alternately

tighten the bolts a few turns at a time

until they are all tight. Then torque

the six pressure plate cover attaching

bolts to specification before removing

the tool.
4.
Apply a light film of grease

(C3VY-19586-A) to the outside diam-

eter of the transmission front bearing

retainer. Apply a light film of grease

(C3VY-19586-A) to both sides of the

release lever fork where it contacts the

release bearing bore spring clips.

Apply a light film of grease to the re-

lease bearing surface that contacts the

pressure plate release fingers. Fill the

grease groove of the release bearing

hub with lithium base grease (C3VY-

19586-A). Clean all excess grease

from inside the bore of bearing hub.

Excess grease will be forced onto the

spline by the transmission input shaft

bearing retainer and will contaminate

the clutch disc. Also, place the release

bearing and hub on the release lever.

5.
Make certain that the flywheel

housing and the cylinder block mount-

ing surfaces are clean. Position the

felt washer on the pivot in the fly-

wheel housing. Slip the pivot into the

clutch equalizer shaft being careful

not to disturb the linkage and at the

same time position the housing on the

dowels in the cylinder block. Install

and torque the attaching bolts to spec-

ification.

6. Install the starting motor and

connect the cable.

7.
The mounting surfaces of the

transmission and the flywheel housing

must be free of dirt, paint, and burrs.

Install two guide pins in the flywheel

housing lower mounting bolt holes.

Move the transmission forward on the

guide pins until it is tightly positioned

against the flywheel housing.

8. Install the two upper mounting

bolts.
Then, remove the guide pins

and install the two lower mounting

bolts.
Torque all the bolts to specifica-

tion.

9. Raise the rear of the engine and
install the crossmember. Install and

torque the crossmember attaching

bolts to specifications, then lower the

engine.

10.
Install the extension housing-

to-engine rear support attaching bolts.

Torque the bolts to specification.

11.
Remove the transmission jack

and connect the parking brake cable.

12.
If the vehicle is equipped with a

four-speed transmission, connect the

gear shift linkage control bracket to

the extension housing.

13.
Connect the gear shift rods to

the transmission. Adjust the shift link-

age as required.

14.
Connect the release lever retain-

ing spring. Install the flywheel housing

cover (390 CID housing only).

15.
Remove the tool from the

transmission output shaft and install

the drive shaft.

16.
Check the clutch pedal free

travel.

CLUTCH ARBOR CLUTCH DISC

PRESSURE PLATE

C 1788-A

FIG. 7—Installing Clutch Disc —

Typicalprocarmanuals.com

05-04-02

Specifications

05-04-02

TORQUE LIMITS (FT-LBS)

Description

Lower Access Clutch Cover Pan to Flywheel Housing Bolts (Cast Iron Housing)

Transmission Assembly to Flywheel Housing Bolts

Pressure Plate and Cover Assembly to Flywheel Attaching Bolts

Clutch Release Equalizer Frame Bracket Bolts

Clutch Pedal Free Travel Adjustment Nut

Flywheel Housing to Cylinder Block Bolts
6-Cylinder

8-Cylinder

Clutch Pedal Assist Spring Bracket to Brake Pedal Support Bracket
Meteor

Ford,
Mercury

17-20

37-42

12-20

15-24

15-20

_

12-17
Mustang,
Cougar

Fairlane, Montego, Falcon

-

-

12-20

15-24

15-20

23-33

40-50

12-17

SPECIAL TOOLS

Tool No.

A-37H

T61L-7657-Aor B

T57L-7657-A

T64P-7657-A
Description

Clutch Disc Aligner-Universal

Transmission Extension Housing Oil Seal

Replacer
Tool No.

CJ91B

T64L-6392-A

T49P-7580-A
Description

Universal Joint Bearing Replacer

Dia-L-lgner Gauge

Clutch Release Bearing Replacerprocarmanuals.com

07-01-02

General Transmission Service

07-01-02

COMPONENT INDEX

FLUID LEAKAGE CHECK

FLUID LEVEL CHECK

FRONT CLUTCH (Forward) INSPECTION

C4 Transmission

C6 Transmission

FMX Transmission

FRONT PUMP AND STATOR SUPPORT

Inspection

FRONT SERVO (Intermediate) INSPECTION

C4 Transmission

C6 Transmission

FMX Transmission

GOVERNOR INSPECTION

HYDRAULIC SYSTEM BENCH TESTS

(FMX)

Pressure Tests

Testing Tool Installation

MANUAL LINKAGE CHECKS

MANUAL SHIFT LINKAGE GROMMET

COLUMN SHIFT

Removal and Installation

NEUTRAL START SWITCH-COLUMN

SHIFT

Adjustment

Removal and Installation

OIL COOLER CLEANING

OIL COOLER TUBES

Removal and Installation

ONE-WAY CLUTCH INSPECTION

OUTPUT SHAFT AND PRIMARY SUN

GEAR

Shaft (FMX)

Inspection

PINION CARRIER, ONE-WAY CLUTCH

AND CENTER SUPPORT (FMX)

Inspection

PINION CARRIERS INSPECTION

C4 Transmission

C6 Transmission

PRESSURE REGULATOR (FMX)

Inspection

REAR CLUTCH (Reverse-High) INSPECTION

C4 Transmission

C6 Transmission

FMX Transmission

REAR SERVO (Low-Reverse) INSPECTION

C4 Transmission
MODEL APPLICATION
All
Models

01-03

01-03

01-16

01-17

01-04

01-11

01-08

01-17
Ford
01-16

01-16

01-16

01-17

01-17

01-17

01-08

01-07

01-11

01-09

01-10

01-12

01-15

01-15

01-15

01-17

01-16

01-16

01-16

01-17

01-17
Mercury
N/A

01-16

N/A

N/A

01-17

N/A

N/A

N/A

01-11

01-09

01-10

N/A

N/A

N/A

01-15

N/A

N/A

01-16

N/A

N/A

N/A
Meteor
01-16

01-16

01-16

01-17

01-17

01-17

01-08

01-07

01-11

01-09

01-10

01-12

01-15

01-15

01-15

01-17

01-16

01-16

01-16

01-17

01-17
Cougar
N/A

01-16

01-16

N/A

01-17

01-17

01-08

01-07

N/A

N/A

N/A

01-12

01-15

N/A

01-15

01-17

N/A

01-16

01-16

N/A

01-17
Fairlane
01-16

01-16

01-16

01-17

01-17

01-17

01-08

01-07

01-11

01-09

01-10

01-12

01-15

01-15

01-15

01-17

01-16

01-16

01-16

01-17

01-17
Falcon
01-16

N/A

N/A

01-17

N/A

N/A

N/A

N/A

01-11

01-09

01-10

N/A

N/A

01-15

N/A

N/A

01-16

N/A

N/A

01-17

N/A
Montego
01-16

01-16

01-16

01-17

01-17

01-17

01-08

01-07

01-11

01-09

01-10

01-12

01-15

01-15

01-15

01-17

01-16

01-16

01-16

01-17

01-17
Mustang
01-16

01-16

01-16

01-17

01-17

01-17

01-08

01-07

N/A

N/A

N/A

01-12

01-15

01-15

01-15

01-17

01-16

01-16

01-16

01-17

01-17
Lincoln-
Continental
N/A

01-16

N/A

N/A

01-17

N/A

N/A

N/A

01-11

01-09

01-10

N/A

N/A

N/A

01-15

N/A

N/A

01-16

N/A

N/A

N/A
Thunderbird
N/A

01-16

N/A

N/A

01-17

N/A

N/A

N/A

01-11

01-09

01-10

N/A

N/A

N/A

01-15

N/A

N/A

01-16

N/A

N/A

N/A
Continental-
Mark
III
N/A

01-16

N/A

N/A

01-17

N/A

N/A

N/A

01-11

01-09

01-10

N/A

N/A

N/A

01-15

N/A

N/A

01-16

N/A

N/A

N/A

A page number indicates that the item is for the vehicle listed at the head of the column.

N/A indicates that the item is not applicable to the vehicle listed.
procarmanuals.com

07-01-03

General Transmission Service

07-01-03

COMPONENT INDEX

FMX Transmission

REAR SUPPORT (FMX)

Inspection

SHIFT POINT CHECKS

STATOR ONE-WAY CLUTCH CHECK

STATOR TO IMPELLOR INTERFERENCE

CHECK

STATOR TO TURBINE INTERFERENCE

CHECK

TRANSMISSION CLEANING

TURBINE AND STATOR END PLAY

CHECK

VACUUM DIAPHRAGM ADJUSTMENT

Altitude Compensating Type

Non-Altitude Compensating Type

VACUUM UNIT CHECK

Altitude Compensating Type

Non-Altitude Compensating Type
MODEL APPLICATION
All
Models

01-06

01-12

01-12

01-12

01-11

01-12
Ford
01-17

01-16

N/A

01-08

N/A

01-05
Mercury
N/A

N/A

N/A

01-08

N/A

01-05
Meteor
01-17

01-16

N/A

01-08

N/A

01-05
Cougar
01-17

01-16

N/A

01-08

N/A

01-05
Fairlane
01-17

01-16

N/A

01-08

N/A

01-05
Falcon
N/A

N/A

N/A

01-08

N/A

01-05
Montego
01-17

01-16

N/A

01-08

N/A

01-05
Mustang
01-17

01-16

N/A

01-08

N/A

01-05
Lincoln-
Continental
N/A

N/A

01-09

N/A

01-06

N/A
Thunderbird
N/A

N/A

01-09

N/A

01-06

N/A
Continental-
Mark
III
N/A

N/A

01-09

N/A

01-06

N/A

A page number indicates that the item is for the vehicle listed at the head of the column.

N/A indicates that the item is not applicable to the vehicle listed.

Three different three-speed trans-

missions are used. The C4 Automatic,

C6 Automatic and the FMX Auto-

matic. Part 7-1 covers testing, com-
mon adjustments and repairs, and

cleaning and inspection for the three

types of transmissions. Where there
are differences in procedures or speci-

fications, the type of transmission af-

fected will be designated.

l
AUTOMATIC TRANSMISSION TESTS

When diagnosing transmission

problems, refer to the Ford Car and

Truck Diagnosis Manual for the de-

tailed information on the items that

could be causing the problem.

The following preliminary checks

should be made before proceeding

with other diagnosis checks.

TRANSMISSION FLUID LEVEL

CHECK

1.
Make sure that the vehicle is

standing level. Then firmly apply the

parking brake.

2.
Run the engine at normal idle

speed. If the transmission fluid is cold

run the engine at fast idle speed

(about 1200 rpm) until the fluid reach-

es its normal operating temperature.

When the fluid is warm, slow the en-

gine down to normal idle speed.

3.
On a vehicle equipped with a

vacuum brake release, disconnect the

release line and plug the end of the
line;
otherwise the parking brake will

not hold the transmission in any drive

position.

4.
Shift the selector lever through

all positions, and place the lever at P.

Do not turn off the engine during the

fluid level checks.

5.
Clean all dirt from the transmis-

sion fluid dipstick cap before remov-

ing the dipstick from the filler tube.

6. Pull the dipstick out of the tube,

wipe it clean, and push it all the way

back into the tube. Be sure it is prop-

erly seated.

7.
Pull the dipstick out of the tube

again, and check the fluid level. The

fluid level should be above the ADD

mark. If necessary, add enough fluid

to the transmission through the filler

tube to bring the level between the

ADD and FULL marks on the dip-

stick. Do not overfill the transmission.

Install the dipstick, making sure it is

fully seated in the tube.
8. Connect the vacuum brake re-

lease line if so equipped, and test it

for proper operation.

FLUID AERATION CHECK

A fluid level that is too high will

cause the fluid to become aerated:

Aerated fluid will cause low control

pressure, and the aerated fluid may be

forced out the vent.

Check the transmission fluid level.

Low fluid level can affect the opera-

tion of the transmission, and may in-

dicate fluid leaks that could cause

transmission damage.

TRANSMISSION FLUID

LEAKAGE CHECKS

Check the speedometer cable con-

nection at the transmission. Replace

the rubber seal if necessary.

Leakage at the oil pan gasket often

can be stopped by tightening the at-
procarmanuals.com

07-01-04
General Transmission Service

07-01-04

taching bolts to the proper torque. If

necessary, replace the gasket.

Check the fluid filler tube connec-

tion at the transmission case or pan.

If leakage is found here, install a new

O-ring or tighten the fitting to the

specified torque.

Check the fluid lines and fittings

between the transmission and the

cooler in the radiator tank for loose-

ness,
wear, or damage. If leakage can-

not be stopped by tightening a fitting,

replace the damaged parts.

Check the engine coolant in the ra-

diator. If transmission fluid is present

in the coolant, the cooler in the radia-

tor is probably leaking.

The cooler can be further checked

for leaks by disconnecting the lines

from the cooler fittings and applying

50-75 psi air pressure to the fittings.

Remove the radiator cap to relieve the

pressure build at the exterior of the oil

cooler tank. If the cooler is leaking

and will not hold this pressure the

cooler must be replaced. Cooler re-

placement is described in the Cooling

System Section of Group 11.

If leakage is found at either the

downshift control lever shaft or the

manual lever shaft, replace either or

both seals.

Inspect the pipe plug on the left

side of the transmission case at the

front. If the plug shows leakage, tor-

que the plug to specifications. If tight-

ening does not stop the leaks, replace

the plug. On a C6 transmission, a TV

pressure plug is also provided on the

right rear side of the case.

When converter drain plugs leak,

remove drain plugs with a six-point

wrench. Coat the threads with FoMo-

Co Perfect Seal Sealing Compound or

its equivalent, and install the plugs.

Torque the drain plugs to specifica-

tion. Fluid leakage from the converter

housing may be caused by engine oil

leaking past the rear main bearing or

from oil gallery plugs, or power steer-

ing oil leakage from steering system.

Be sure to determine the exact cause

of the leak before repair procedures

are started.

Oil-soluble aniline or fluorescent dyes

premixed at the rate of 1/2 teaspoon

of dye powder to 1/2 pint of transmis-

sion fluid have proved helpful in locat-

ing the source of the fluid leakage.

Such dyes may be used to determine

whether an engine oil or transmission

fluid leak is present or if the fluid in

the oil cooler leaks into the engine

coolant system. A black light, how-

ever, must be used with the fluorescent

dye solution.
DISHED OR

FLAT WASHER

" O.D.,
a" STEEL PLATE

5/8"X \W,

DRILL TO SUIT
HEX. HEAD SCREW

3/8"-24 X Vl

HEX. NUT W—
24

WELD

TOGETHER

WING
NUT

>/2"_13
THREAD

CHAIN,
10"
LONG
RUBBER PLUG

1
Vi" DIA. X 2"

LONG Vl"

HOLE THRU

APPROXIMATELY

40 DUROMETER
FLAT WASHER

Vs" O.D.

PLUG

VALVE
STANDARD BOLT

W-13
X 4Vl"

LONG SQUARE

THREAD
END

REMOVE HEAD

AND WELD
TO

WASHER

STANDARD 1/8" FITTING-87971-S FOR

RETAPPED DRAIN PLUG THREADS-USE

1/4" OVERSIZE FITTING-87973-S

D 1067-B
WELD TOGETHER

SECURELY—MUST

NOT LEAK

FIG. 2—Converter Leak Checking Tool

CONVERTER LEAKAGE

CHECK

If there are indications that the

welds on the torque converter are

leaking, the converter will have to be

removed and the following check

made before the unit is replaced.

A leak checking tool (Fig. 2) can be

made from standard parts. The tool

can be used to check all converters.

1.
Install the plug in the converter

(Fig. 3) and expand it by tightening

the wing nut. Attach the safety chains.

2.
Install the air valve in one of the

drain plug holes.

3.
Introduce air pressure into the

converter. Check the pressure with a

tire gauge and adjust it to 20 psi.

4.
Place the converter in a tank of

water. Observe the weld areas for

bubbles. If no bubbles are observed, it

may be assumed that the welds are

not leaking.

ENGINE IDLE SPEED CHECK

Check and, if necessary, adjust the

engine idle speed, using the procedure

given in Group 10.

If the idle speed is too low, the en-

gine will run roughly. An idle speed

that is too high will cause the vehicle

to creep, have harsh engagements and

harsh closed-throttle downshifts.
ANTI-STALL DASHPOT

CLEARANCE CHECK

After the engine idle speed has been

properly adjusted, check the anti-stall

dashpot clearance. Follow the proce-

dure given in Group 10 for checking

and adjusting this clearance.

MANUAL LINKAGE CHECKS

Correct manual linkage adjustment

is necessary to position the manual

valve for proper fluid pressure direc-

tion to the different transmission com-

ponents. Improperly adjusted manual

Tire Pressure Gauge

D1921-A

FIG. 3—Converter Leak Checking

Tool Installationprocarmanuals.com