1969 FORD MUSTANG engine oil

07-01-03

General Transmission Service

07-01-03

COMPONENT INDEX

FMX Transmission

REAR SUPPORT (FMX)

Inspection

SHIFT POINT CHECKS

STATOR ONE-WAY CLUTCH CHECK

STATOR TO IMPELLOR INTERFERENCE

CHECK

STATOR TO TURBINE INTERFERENCE

CHECK

TRANSMISSION CLEANING

TURBINE AND STATOR END PLAY

CHECK

VACUUM DIAPHRAGM ADJUSTMENT

Altitude Compensating Type

Non-Altitude Compensating Type

VACUUM UNIT CHECK

Altitude Compensating Type

Non-Altitude Compensating Type
MODEL APPLICATION
All
Models

01-06

01-12

01-12

01-12

01-11

01-12
Ford
01-17

01-16

N/A

01-08

N/A

01-05
Mercury
N/A

N/A

N/A

01-08

N/A

01-05
Meteor
01-17

01-16

N/A

01-08

N/A

01-05
Cougar
01-17

01-16

N/A

01-08

N/A

01-05
Fairlane
01-17

01-16

N/A

01-08

N/A

01-05
Falcon
N/A

N/A

N/A

01-08

N/A

01-05
Montego
01-17

01-16

N/A

01-08

N/A

01-05
Mustang
01-17

01-16

N/A

01-08

N/A

01-05
Lincoln-
Continental
N/A

N/A

01-09

N/A

01-06

N/A
Thunderbird
N/A

N/A

01-09

N/A

01-06

N/A
Continental-
Mark
III
N/A

N/A

01-09

N/A

01-06

N/A

A page number indicates that the item is for the vehicle listed at the head of the column.

N/A indicates that the item is not applicable to the vehicle listed.

Three different three-speed trans-

missions are used. The C4 Automatic,

C6 Automatic and the FMX Auto-

matic. Part 7-1 covers testing, com-
mon adjustments and repairs, and

cleaning and inspection for the three

types of transmissions. Where there
are differences in procedures or speci-

fications, the type of transmission af-

fected will be designated.

l
AUTOMATIC TRANSMISSION TESTS

When diagnosing transmission

problems, refer to the Ford Car and

Truck Diagnosis Manual for the de-

tailed information on the items that

could be causing the problem.

The following preliminary checks

should be made before proceeding

with other diagnosis checks.

TRANSMISSION FLUID LEVEL

CHECK

1.
Make sure that the vehicle is

standing level. Then firmly apply the

parking brake.

2.
Run the engine at normal idle

speed. If the transmission fluid is cold

run the engine at fast idle speed

(about 1200 rpm) until the fluid reach-

es its normal operating temperature.

When the fluid is warm, slow the en-

gine down to normal idle speed.

3.
On a vehicle equipped with a

vacuum brake release, disconnect the

release line and plug the end of the
line;
otherwise the parking brake will

not hold the transmission in any drive

position.

4.
Shift the selector lever through

all positions, and place the lever at P.

Do not turn off the engine during the

fluid level checks.

5.
Clean all dirt from the transmis-

sion fluid dipstick cap before remov-

ing the dipstick from the filler tube.

6. Pull the dipstick out of the tube,

wipe it clean, and push it all the way

back into the tube. Be sure it is prop-

erly seated.

7.
Pull the dipstick out of the tube

again, and check the fluid level. The

fluid level should be above the ADD

mark. If necessary, add enough fluid

to the transmission through the filler

tube to bring the level between the

ADD and FULL marks on the dip-

stick. Do not overfill the transmission.

Install the dipstick, making sure it is

fully seated in the tube.
8. Connect the vacuum brake re-

lease line if so equipped, and test it

for proper operation.

FLUID AERATION CHECK

A fluid level that is too high will

cause the fluid to become aerated:

Aerated fluid will cause low control

pressure, and the aerated fluid may be

forced out the vent.

Check the transmission fluid level.

Low fluid level can affect the opera-

tion of the transmission, and may in-

dicate fluid leaks that could cause

transmission damage.

TRANSMISSION FLUID

LEAKAGE CHECKS

Check the speedometer cable con-

nection at the transmission. Replace

the rubber seal if necessary.

Leakage at the oil pan gasket often

can be stopped by tightening the at-
procarmanuals.com

07-01-04
General Transmission Service

07-01-04

taching bolts to the proper torque. If

necessary, replace the gasket.

Check the fluid filler tube connec-

tion at the transmission case or pan.

If leakage is found here, install a new

O-ring or tighten the fitting to the

specified torque.

Check the fluid lines and fittings

between the transmission and the

cooler in the radiator tank for loose-

ness,
wear, or damage. If leakage can-

not be stopped by tightening a fitting,

replace the damaged parts.

Check the engine coolant in the ra-

diator. If transmission fluid is present

in the coolant, the cooler in the radia-

tor is probably leaking.

The cooler can be further checked

for leaks by disconnecting the lines

from the cooler fittings and applying

50-75 psi air pressure to the fittings.

Remove the radiator cap to relieve the

pressure build at the exterior of the oil

cooler tank. If the cooler is leaking

and will not hold this pressure the

cooler must be replaced. Cooler re-

placement is described in the Cooling

System Section of Group 11.

If leakage is found at either the

downshift control lever shaft or the

manual lever shaft, replace either or

both seals.

Inspect the pipe plug on the left

side of the transmission case at the

front. If the plug shows leakage, tor-

que the plug to specifications. If tight-

ening does not stop the leaks, replace

the plug. On a C6 transmission, a TV

pressure plug is also provided on the

right rear side of the case.

When converter drain plugs leak,

remove drain plugs with a six-point

wrench. Coat the threads with FoMo-

Co Perfect Seal Sealing Compound or

its equivalent, and install the plugs.

Torque the drain plugs to specifica-

tion. Fluid leakage from the converter

housing may be caused by engine oil

leaking past the rear main bearing or

from oil gallery plugs, or power steer-

ing oil leakage from steering system.

Be sure to determine the exact cause

of the leak before repair procedures

are started.

Oil-soluble aniline or fluorescent dyes

premixed at the rate of 1/2 teaspoon

of dye powder to 1/2 pint of transmis-

sion fluid have proved helpful in locat-

ing the source of the fluid leakage.

Such dyes may be used to determine

whether an engine oil or transmission

fluid leak is present or if the fluid in

the oil cooler leaks into the engine

coolant system. A black light, how-

ever, must be used with the fluorescent

dye solution.
DISHED OR

FLAT WASHER

" O.D.,
a" STEEL PLATE

5/8"X \W,

DRILL TO SUIT
HEX. HEAD SCREW

3/8"-24 X Vl

HEX. NUT W—
24

WELD

TOGETHER

WING
NUT

>/2"_13
THREAD

CHAIN,
10"
LONG
RUBBER PLUG

1
Vi" DIA. X 2"

LONG Vl"

HOLE THRU

APPROXIMATELY

40 DUROMETER
FLAT WASHER

Vs" O.D.

PLUG

VALVE
STANDARD BOLT

W-13
X 4Vl"

LONG SQUARE

THREAD
END

REMOVE HEAD

AND WELD
TO

WASHER

STANDARD 1/8" FITTING-87971-S FOR

RETAPPED DRAIN PLUG THREADS-USE

1/4" OVERSIZE FITTING-87973-S

D 1067-B
WELD TOGETHER

SECURELY—MUST

NOT LEAK

FIG. 2—Converter Leak Checking Tool

CONVERTER LEAKAGE

CHECK

If there are indications that the

welds on the torque converter are

leaking, the converter will have to be

removed and the following check

made before the unit is replaced.

A leak checking tool (Fig. 2) can be

made from standard parts. The tool

can be used to check all converters.

1.
Install the plug in the converter

(Fig. 3) and expand it by tightening

the wing nut. Attach the safety chains.

2.
Install the air valve in one of the

drain plug holes.

3.
Introduce air pressure into the

converter. Check the pressure with a

tire gauge and adjust it to 20 psi.

4.
Place the converter in a tank of

water. Observe the weld areas for

bubbles. If no bubbles are observed, it

may be assumed that the welds are

not leaking.

ENGINE IDLE SPEED CHECK

Check and, if necessary, adjust the

engine idle speed, using the procedure

given in Group 10.

If the idle speed is too low, the en-

gine will run roughly. An idle speed

that is too high will cause the vehicle

to creep, have harsh engagements and

harsh closed-throttle downshifts.
ANTI-STALL DASHPOT

CLEARANCE CHECK

After the engine idle speed has been

properly adjusted, check the anti-stall

dashpot clearance. Follow the proce-

dure given in Group 10 for checking

and adjusting this clearance.

MANUAL LINKAGE CHECKS

Correct manual linkage adjustment

is necessary to position the manual

valve for proper fluid pressure direc-

tion to the different transmission com-

ponents. Improperly adjusted manual

Tire Pressure Gauge

D1921-A

FIG. 3—Converter Leak Checking

Tool Installationprocarmanuals.com

07-01-08
General Transmission Service

07-01-08

3.
Install the bench testing tool on

the transmission.

4.
Remove the
1/8-inch
pipe plug

at the transmission case. Turn the

front pump in a clockwise direction at

75-100 rpm until a regular flow of

transmission fluid leaves the hole in

the transmission case. This operation
bleeds the air from the pump.

5.
Install the pressure gauge (77820

or T57L-77820-A) as shown in Fig.

13.

PRESSURE TESTS

Turn the front pump at 75-100 rpm
and note the gauge readings. The

pressure readings on the bench test

must be within the limits as outlined

in Figure 13, for the engine idle check.

If pressure gauge readings are with-

in limits in all selector lever positions,

install the vacuum diaphragm control

rod unit.

COMMON ADJUSTMENTS AND REPAIRS

TRANSMISSION FLUID DRAIN

AND REFILL

Normal maintenance and lubrica-

tion requirements do not necessitate

periodic automatic transmission fluid

changes.

If a major repair, such as a clutch

band, bearing, etc., is required in the

transmission, it will have to be re-

moved for service. At this time the

converter, transmission cooler and

cooler lines must be thoroughly

flushed to remove any dirt.

When filling a dry transmission and

converter, install five quarts of fluid.

Start the engine, shift the selector

lever as outlined below, and check and

add fluid as necessary.

Following are the procedures for

partial drain and refill due to in-

vehicle repair operation.

C4 TRANSMISSION

1.
On PEA models, disconnect the

fluid filler tube from the transmission

oil pan to drain the fluid.

On PEB and PEE models, loosen

the pan attaching bolts to drain the

fluid from the transmission.

2.
When the fluid has stopped

draining from the transmission, re-

move and thoroughly clean the pan

and the screen. Discard the pan gas-

ket.

3.
Place a new gasket on the pan,

and install the pan on the transmis-

sion.

4.
On PEA models, connect the

filler tube to the pan and tighten the

fitting securely.

5.
Add three quarts of fluid to the

transmission through the filler tube.

6. Run the engine at idle speed for

about two minutes, and then run it at

fast idle speed (about 1200 rpm) until

it reaches it's normal operating temp-

erature. Do not race the engine.

7.
Shift the selector lever through

all the positions, place it at P, and

check the fluid level. The fluid level

should be above the ADD mark. If
necessary, add enough fluid io the

transmission to bring the level be-

tween the ADD and FULL marks on

che dipstick. Do not overfill the trans-

mission.

FMX OK C6

TRANSMISSION

1.
Raise the vehicle on a hoist or

jack stands.

2.
Place a drain pan under the

transmission.

3.
Loosen the pan attaching bolts

to drain the fluid from the transmis-

sion.

4.
After the fluid has drained to the

level of the pan flange, remove the

rest of the pan bolts working from the

rear and both sides of the pan to

allow it to drop and drain slowly.

5.
When the fluid has stopped

draining from the transmission, re-

move and thoroughly clean the pan

and the screen. Discard the pan gas-

ket.

6. Place a new gasket on the pan,

and install the pan on the transmis-

sion.

7.
Add three quarts of fluid to the

transmission through the filler tube.

8. Run the engine at idle speed for

about two minutes, and then run it at

fast idle speed (about 1200 rpm) until

it reaches normal operating tempera-

ture.
Do not race the engine.

9. Shift the selector lever through

all the positions, place it at P, and

check the fluid level. The fluid level

should be above the ADD mark. If

necessary, add enough fluid to the

transmission to bring the level be-

tween the ADD and FULL marks on

the dipstick. Do not overfill the trans-

mission.

OIL COOLER TUBE

REMOVAL AND INSTALLATION

When fluid leakage is found at the

oil cooler, the cooler must be re-

placed. Cooler replacement is de-

scribed in the Cooling System Section

of Group 11.
When one or more of the fluid

cooler steel tubes must be replaced,

each replacement tube must be fabri-

cated from the same size steel tubing

as the original line.

Using the old tube as a guide, bend

the new tube as required. Add the

necessary fittings, and install the tube.

After the fittings have been tight-

ened, add fluid as needed, and check

for fluid leaks.

VACUUM DIAPHRAGM

ADJUSTMENT NON-ALTITUDE

COMPENSATING TYPE

The C4 and C6 transmissions are

equipped with an adjustable vacuum

diaphragm assembly. A similar ad-

justable diaphragm has been released

for service with the FMX transmis-

sion. However, the FMX service dia-

phragm is not interchangeable with

that used on C4 and C6 models.

The vacuum diaphragm assembly

has an adjusting screw in the vacuum

hose connecting tube (Fig. 14).

SPRING

SEAT

THIS CLEARANCE CHANGED

BY ADJUSTING SCREW

D1830-A

FIG. 14—Adjustable Vacuum Unit

The inner end of the screw bears

against a plate which in turn bears

against the vacuum diaphragm spring.

All readings slightly high or all

readings slightly low may indicate the

vacuum unit needs adjustment to cor-

rect a particular shift condition.procarmanuals.com

07-02-03

C4 Automatic Transmission

07-02-03

CONVERTER

FORWARD CLUTCH
PRIMARY GOVERNOR

CONVERTER

CHECK VALVE
ONE-WAY

CLUTCH

DRAIN-BACK

VALVE

FRONT LUBE

CONVERTER

PRESSURE

RELIEF VALVE
LOW AND

REVERSE

SERVO
AND DIRECT

CLUTCH

L

SECONDARY

GOVERNOR
INTERMEDIATE

BAND

ACCUMULATOR

VALVE
CUT-BACK
VALVE

2-3
BACK-OUT

VALVE

MAIN

REGU-

LATOR

VALVE
MANUAL
LOW

VALVE

1-2 SHIFT

VALVE

D2
VALVE
THROTTLE

MODULATOR

VALVE

THROTTLE

BOOST VALVE

PRESSURE

BOOSTER

VALVE

DOWNSHIFT VALVE

LINE

COASTING

BOOST

VALVE
ENGINE
MANIFOLD
VACUUM

LESS THAN
20
INCHES

PRIMARY

THROTTLE

VALVE

(CASE)
VACUUM

DIAPHRAGM

OIL
SCREEN

I) 1724-E

FIG. 3—Hydraulic Control Systemprocarmanuals.com

07-02-07
C4 Automatic Transmission

07-02-07

2.
Remove the selector lever handle

from the lever.

3.
Remove the trim panel from the

top of the console.

4.
Remove the cover and dial indi-

cator as an assembly.

5.
Remove the four screws that se-

cure the selector lever retainer to the

selector lever housing. Lift the retainer

from the housing.

6. Loosen the two combination

starter neutral and back-up light

switch attaching screws (Fig. 10).

7.
Move the selector lever back and

forth until the gauge pin (No. 43 drill)

can be fully inserted into the gauge

pin holes (Fig. 10).

8. Place the transmission selector

lever firmly against the stop of the

neutral detent position.

9. Slide the combination starter

neutral and back-up light switch for-

ward or rearward as required, until

the switch actuating lever contacts the

selector lever.

10.
Tighten the switch attaching

screws and remove the gauge pin.

Check for starting in the park posi-

tion.

11.
Turn the ignition key to the

ACC position and place the selector

lever in the reverse position and check

the operation of the back-up lights.

Turn the key off.

12.
Position the selector lever re-

tainer to the selector lever housing.

Install the four attaching screws.

13.
Install the cover and dial indi-

cator.

14.
Install the trim panel on the top

of the console. Install the selector

lever handle.

MUSTANG

1.
With the manual lever properly

NEUTRAL
START

SWITCH

(D1439-A

FIG. 11—Neutral Start Switch

Adjustments—Console Shift—

Mustang
adjusted, loosen the two switch attach-

ing bolts (Fig. 11).

2.
With the transmission manual

lever in neutral, rotate the switch and

insert the gauge pin (No. 43 drill

shank end) into the gauge pin holes of

the switch. The gauge pin has to be

inserted to a full 31/64 inch into the

three holes of the switch (Fig. 11).

3.
Torque the two switch attaching

bolts to specification. Remove the

gauge pin from the switch.

4.
Check the operation of the

switch. The engine should start only

with the transmission selector lever in

Neutral and Park.

NEUTRAL START SWITCH

REPLACEMENT—CONSOLE SHIFT

On vehicles equipped with a column

mounted neutral start switch, refer to

Part 7-1, Section 2, for the replace-

ment procedures.

FORD-METEOR

1.
Remove the four screws and

plates securing the selector lever

handle to the lever. Remove the

handle and detent control.

2.
Remove the two screws from the

rear of the console top panel. Pull the

panel back to unhook it from the

front of the console and remove the

panel.

3.
Remove the two screws securing

the dial indicator assembly to the se-

lector lever housing and remove the

indicator assembly.

4.
Disconnect the neutral start

switch wires at the plug connector.

Remove the wires from under the re-

taining clip.

5.
Remove the two screws securing

the neutral start switch to the selector

lever housing and remove the switch

(Fig. 9).

6. Position the neutral start switch

to the selector lever housing and in-

stall the two attaching screws.

7.
Adjust the neutral start switch as

outlined under the Neutral Start

Switch Adjustment procedures in this

section.

8. Connect the neutral start switch

wires to the plug connector. Position

the wires in the retaining clip and

close the clip.

9. Place the console top panel on

the console and install the retaining

screws.

10.
Position the selector lever de-

tent control and handle on the selector

lever and secure with the four plates

and attaching screws.

FAIRLANE-MONTEGO

1.
Remove the selector lever handle

from the lever.
2.
Remove the trim panel from the

top of the console.

3.
Remove the cover and dial indi-

cator as an assembly.

4.
Remove the four screws that se-

cure the selector lever retainer to the

selector lever housing. Lift the retainer

from the housing.

5.
Remove the two screws securing

the neutral start switch to the selector

lever housing. Disconnect the neutral

start switch wires at the plug connec-

tor and remove the switch.

6. Position the neutral start switch

to the selector lever housing and in-

stall the two attaching screws.

7.
With the selector lever in neu-

tral,
move the selector lever back and

forth until the gauge pin (No. 43 drill)

can be fully inserted into the gauge

pin holes (Fig. 10).

8. Place the transmission selector

lever firmly against the stop of the

neutral detent position.

9. Slide the combination starter

neutral and back-up light switch for-

ward or rearward as required, until

the switch actuating lever contacts the

selector lever.

10.
Tighten the switch attaching

screws and remove the gauge pin.

11.
Connect the neutral start switch

wires to the plug connector and check

for starting in the park position.

12.
Position the selector lever re-

tainer to the selector lever housing.

Install the attaching screws.

13.
Install the cover and dial indi-

cator.

14.
Install the trim panel on the top

of the console. Install the selector

lever handle

MUSTANG

1.
Remove the downshift linkage

rod from the transmission downshift

lever.

2.
Apply penetrating oil to the

downshift lever shaft and nut. Remove

the transmission downshift outer lever

retaining nut and lever (Fig. 11).

3.
Remove the two neutral start

switch attaching bolts.

4.
Disconnect the multiple wire

connector. Remove the neutral switch

from the transmission.

5.
Install the neutral start switch on

the transmission. Install the two at-

taching bolts.

6. With the transmission manual

lever in neutral, rotate the switch and

install gauge pin (No. 43 drill) into

the gauge pin hole (Fig. 11).

7.
Tighten the switch attaching

bolts to specification and remove the

gauge pin.procarmanuals.com

07-02-11
C4 Automatic Transmission
07-02-11

REMOVAL AND INSTALLATION

An oil impregnated plastic grommet

is incorporated in the end of the man-

ual shift linkage lever arm on all col-

umn shift vehicles. A special tool

T67P-7341-A is required to install the

grommet in the manual lever, and to

install the manual linkage rod into the

grommet. Refer to Part 7-1, Section

2,
for the grommet replacement pro-

cedures.

TRANSMISSION REMOVAL

1.
Raise the vehicle and remove the

converter cover attaching bolts, at the

lower front side of the converter hous-

ing. Remove the cover.

2.
Remove the two conveter drain

plugs (Fig. 20). Drain the fluid from

the converter. Install the two convert-

er drain plugs.

3.
Remove the drive shaft and in-

stall the extension housing seal repla-

cer tool in the extension housing.

4.
Remove the vacuum line hose

from the transmission vacuum unit.

Disconnect the vacuum line from the

retaining clip.

5.
Remove the two extension

housing-to-crossmember attaching

bolts.

6. Remove the speedometer cable

from the extension housing.

7.
Disconnect the exhaust pipe

flange from the manifolds.

8. Remove the parking brake cable

from the equalizer lever.

9. Remove the fluid filler tube from

the pan and drain the transmission

fluid on PEA models. On PEB and

PEE models, loosen the transmission

CONVERTER A
ATT,
pan bolts and drain the fluid at one

corner of the pan. Tighten the attach-

ing bolts after the fluid has drained.

10.
Disconnect the fluid cooler lines

from the transmission case.

11.
Remove the manual and kick-

down linkage rods from the transmis-

sion control levers.

On vehicles equipped with a column

shift, use tool T67P-7341-A to remove

the selector rod from the manual

lever.

12.
On a Mustang, disconnect the

neutral start switch wires from the re-

taining clamps and connectors.

13.
Disconnect the starter cable.

Remove the starter attaching bolts

and remove the starter from the con-

verter housing.

14.
On PEB and PEE models, lift

the fluid filler tube from the case.

15.
Remove the four converter-

to-flywheel attaching nuts.

16.
Position the transmission jack

to support the transmission and secure

the transmission to the jack with a

safety chain.

17.
Remove the four crossmember

attaching bolts and lower the

crossmember.

18.
Remove the five converter

housing-to-engine attaching bolts.

Lower the transmission (Fig. 21) and

remove it from under the vehicle.

TRANSMISSION

INSTALLATION

1.
With the converter properly in-

D 2043-A

FIG. 20—Converter Drain Plug

Location
FIG. 21—Transmission Mounted

on Jack
stalled, place the transmission on the

jack (Fig. 21). Secure the transmission

to the jack with the safety chain.

2.
Raise the transmission into posi-

tion and install the five converter

housing-to-engine attaching bolts.

Torque the bolts to specification. Re-

move the safety chain from the trans-

mission.

3.
Position the crossmember and

install the four attaching bolts. Torque

the bolts to specifications.

4.
Lower the transmission and in-

stall the extension housing and

crossmember attaching bolts. Torque

the bolts to specification.

5.
Install the four flywheel to con-

verter attaching nuts. Torque the nuts

to specification.

6. Remove the transmission jack.

Install the fluid filler tube in the

transmission case or pan. Install the

vacuum hose on the transmission vac-

uum unit. Install the vacuum line re-

taining clip.

7.
Connect the fluid cooling lines to

the transmission case.

8. On a Mustang, connect the neu-

tral start switch wires to their respec-

tive connectors and secure the harness

in the retaining clamps.

9. Install the linkage rods on the

transmission downshift and manual

control levers.

On vehicles equipped with a column

shift, use tool T67P-7341-A to install

a new grommet in the manual lever,

and to install the manual linkage rod

into the grommet.

10.
Connect the speedometer cable

to the extension housing.

11.
Connect the exhaust inlet pipes

to the manifolds.

12.
Install and adjust the parking

brake cable at the equalizer lever.

13.
Install the converter housing

cover and torque the attaching bolts

to specification.

14.
Install the starter and torque

the attaching bolts to specification.

Connect the starter cable.

15.
Install the drive shaft. Torque

the companion flange U-bolts attach-

ing nuts to specification.

16.
Lower the vehicle. Fill the

transmission to the proper level with

the specified fluid. Adjust the manual

and downshift linkage.procarmanuals.com

07-02-17

C4 Automatic Transmission

07-02-17

Vehicle

Ford,
Meteor

Fairlane,

Montegc,
Falcon,

Mustang

Ford,
Meteor

Fairlane,

Montego,
Mustang

Mustang

Falcon
Engine

302-2V

302-2V

240-IV

250-1V

200-1V

170-1V

200-1V
Transmi ssion

PEA-MI,
Nl

PEE-M,
V, AC

PEA-A2

PEE-AD,

AE,
AF

PEB-B2

PEB-C2
Servo Piston

Dia.
A

3.7875

3.7875

3.3265
Dia.
B

2.8265

2.7065

2.4865
Servo Cover

Dia.
C

None

None

3.340
Dia.
D

2.840

2.975

2.500
Spring

Free Length

(Inches)

2.480

2.480

2.480
Color

Cniif

White

White

White

D 1800-D

FIG. 46—Intermediate Servo Piston, Cover and Spring Identification

inch bolts and install the transmission

identification tag and the other two

cover attaching bolts. Torque the bolts

to specifications.

Downshift and Manual

Linkage

1.
Apply penetrating oil to the

outer lever attaching nut to prevent

UPPER RETAINING RING
breaking the inner lever shaft. Remove

the downshift outer lever nut. Remove

the downshift outer and inner lever.

From inside the transmission case, re-

move the upper retaining ring from

the manual lever link (Fig. 47). Re-

move the upper end of the lever link

from the case retaining pin.

2.
From the back of the transmis-

sion case, remove the upper retaining

INNER MANUAL

'ER ATTACHING NUT

mmMm

INNER MANUAL LEVER MANUAL LEVER LINK

FIG. 47—Case Internal Linkage
ring and flat washer from the parking

pawl link (Fig. 48). Remove the pawl

link from the case retaining pin.

3.
From the back of the transmis-

sion case, remove the parking pawl

link, toggle rod, and manual lever link

as an assembly (Fig. 49).

UPPER

r RETAINING

RING

D1885-A

FIG. 48—Parking Pawl Link

/7^-MANUAL LEVER LINK

D1405-B
FIG. 49—Removing or Installing

Parking Pawl Link

4.
Remove the rear parking pawl

link lower retaining ring, flat washer

and link from the toggle rod (Fig. 50).

5.
Remove the manual lever link,

lower retaining ring, flat washer, and

link from the toggle rod.

6. Install the manual and marking

pawl links, flat washers and retaining

rings to the toggle rods.

7.
Remove the inner manual lever

attaching nut and lever. Remove the

outer manual lever from the case.

8. To remove the manual lever seal,

use the tools shown in Fig. 51. To in-

stall the new seal, use a driver that fits

the ID of the seal.

9. Install the outer manual lever in

the case. Install the inner manual

lever and attaching nut with the cham-

fer facing toward the lever (Fig. 47).

Torque the nut to specification.

10.
From the back of the transmis-

sion case, install the parking toggle

rod and link assembly into the case

(Fig. 49).

11.
Install the parking pawl link on

the case retaining pin. Install the flat

washer and link retaining ring (Fig.

48).procarmanuals.com

07-03-03
FMX Transmission

0703-03

PRIMARY DISTRIBUTOR SLEEVE EXTENSION HOUSING SEAL

SUN GEAR ! SPEEDOMETER DRIVE GEAR /

OIL SEAL ONE-WAY CLUTCH

FRONT FRONT

PUMP BAND

FRONT

CLUTCH

OUTPUT SHAFT

EXTENSION HOUSING

SPLINE SEAL

GOVERNOR

PRIMARY PINION

SECONDARY SUN GEAR

SECONDARY PINION

DIAPHRAGM

CONTROL VALVE BODY

OIL PAN

TURBINE SHAFT

FLYWHEEL
'REAR CLUTCH PISTON

REAR CLUTCH

REAR CLUTCH SPRING

FRONT CLUTCH PISTON

FRONT SERVO

PRESSURE REGULATOR BODY

STATOR SUPPORT

D 2045-A

FIG. 7—Typical FMX Transmission

TRANSMISSION MODEL

ENGINE DISPLACEMENT
BUILD DATE

FMX TRANSMISSION
SHIFT

D 2046-A

FIG. 2—Identification Tagsprocarmanuals.com