1967 CHEVROLET CAMARO fuel type

LUBRICATION 0-13

LUBRICATION

INDEX

Page

Engine Crankcase Oil . 0-13

Crankcase Capacities. . 0-13

Lubrication . ,
•
o-13

SAE Viscosity Oils 0-13

Types of Oils 0-14

Maintaining Oil Level 0-14

Oil and Filter Change Intervals 0-14

Oil.
. . ...:.. 0-14

Filter o-14

Crankcase Dilution . 0-14

Automatic Control Devices to Minimize

Crankcase Dilution 0-14

Crankcase Breather Cap 0-14

Crankcase Ventilation System 0-15

Valve Type 0-15

Fuel Filter 0-15

Air Cleaner . 0-15

Polyurethane Type 0-15

Oil Wetted Paper Element Type 0-15

Battery Terminal Washers 0-15
Page

Distributor 0-15

Rear Axle and 3-Speed and Overdrive

4-Speed Transmission 0-15

Recommended Lubricants 0-15

Multi-Purpose Gear Lubricants 0-15

Lubricant Additions 0-15

Lubricant Changes 0-15

Powerglide Transmission 0-15

Turbo Hydra-Matic 0-16

Front Wheel Bearings 0-16

Manual Steering Gear . . . . 0-16

Power Steering 0-16

Air Conditioning 0-16

Brake Master Cylinder. 0-16

Parking Brake 0-16

Clutch Cross-Shaft , 0-16

Chassis Lubrication 0-16

Lubrication Diagrams . . 0-19

Body Lubrication (Chevrolet, Chevelle, Chevy n, Camaro). 0-20

Body Lubrication Points (Corvette) . 0-21

The selection of the proper lubricant and its correct

application at regular intervals does much to increase the

life and operation of all moving parts of the vehicle.

Consequently, it is important that the correct grade of

oil or grease, as noted in the following pages, be used.

ENGINE CRANKCASE OIL

Crankcase Capacity

4 Cylinder 4 qt.

6 Cylinder 4 qt.

8 Cylinder (283) 4 qt.

8 Cylinder (327) 4 qt.

8 Cylinder (350) 4 qt.

8 Cylinder (396) 4 qt.

8 Cylinder (427) Chevrolet 4 qt.

8 Cylinder (427) Corvette 5 qt.

For 4 Cyl. Add .5 qt. with filter change;

1 qt. for 6 and 8 Cyl. engines.

Lubrication

Crankcase oil should be selected to give the best per-

formance under the climatic and driving conditions in the

territory in which the vehicle is driven.

During warm or hot weather, an oil which will provide

adequate lubrication under high operating temperatures

is required.

During the colder months of the year* an oil which will

permit easy starting at the lowest atmospheric tempera-

ture likely to be encountered, should be used.

When the crankcase is drained and refilled, the crank-

case oil should be selected, not on the basis of the exist-

ing temperature at the time of the change, but on the

lowest temperature anticipated for the period during

which the oil is to be used.

Unless the crankcase oil is selected on the basis of

viscosity or fluidity of the anticipated temperature, dif-

ficulty in starting will be experienced at each sudden

drop in temperature.
SAE Viscosity Oils

SAE Viscosity Numbers indicate only the viscosity or

body of the oil, that is, whether an oil is a light or a

heavy body oil, and do not consider or include other

properties or quality factors.

The lower SAE Viscosity Numbers, such as SAE 5W

and SAE 10W which represent the light body oils, are

recommended for use during cold weather to provide

easy starting and instant lubrication. The higher SAE

Viscosity Numbers such as SAE 20 and SAE 20W, which

represents heavier body oils, are recommended for use

during warm or hot weather to provide improved oil

economy and adequate lubrication under high operating

temperatures.

Oils are available which are designed to combine the

easy starting characteristics of the lower SAE Viscosity

Number with the warm weather operating characteristics

of the higher SAE Viscosity Number. These are termed

"multi-viscosity oils," SAE 5-10W, SAE 5W-20, SAE

10W-20W, and SAE 10W-30.

The following chart will serve as a guide for the

selection of the correct SAE Viscosity Number for use

under different atmospheric temperature ranges, and

suggests the appropriate SAE Viscosity Numbers when

multi-viscosity oils are used.

Lowest Anticipated

Temperature

During Time

Oil Will Be

in Crankcase

32°F.

0°F.

Below 0°F.
Recommended

SAE Viscosity

Oils

SAE 20 or 20W

SAE 10W

SAE 5W
Recommended

SAE

Multi-

Viscosity

Oils

SAE 10W-30 .

SAE 10W-30

SAE 5W-20

SAE 30 or 10W-30 is recommended when most of the

driving is at high speeds and/or at temperatures above

90
°F.

CHEVROLET CHASSIS SERVICE MANUAL

LUBRICATION 0-14

SAE 5W-30 oils may be used during periods when

temperatures of 32° and below are to be expected.

Types of Oils

In service, crankcase oils may form sludge and varnish

and under some conditions, corrosive acids unless pro-

tected against oxidation.

To minimize the formation of these harmful products

and to assure the use of oil best suited for present day

operating conditions, automobile manufacturers have de-

veloped a series of sequence tests designed to evaluate

the ability of any oil to properly lubricate automobile

engines.

It is recommended that only those oils which are

certified by their suppliers as meeting or exceeding the

maximum severity requirements of these sequence tests

(or GM Standard 4745-M) be used in Chevrolet engines.

Certified sequence tested oils will be described as such

on their containers.

Maintaining Oil Level

The oil gauge rod is marked "Full" and "Add Oil."

These notations have broad arrows pointing to the level

lines.
The oil level should be maintained between the

two lines, neither going above the "Full" line nor under

the "Add Oil" line. DO NOT OVERFILL. After operating

vehicle allow a few minutes for oil to return to crankcase

before checking oil level.

Check the oil level frequently and add oil when

necessary.

Oil and Filter Change Intervals

NOTE:
Under prolonged dusty driving condi-

tions,
it is recommended that these operations

be performed more often.

OIL

To insure continuation of best performance, low main-

tenance cost and long engine life, it is necessary to

change the crankcase oil whenever it becomes contami-

nated with harmful foreign materials. Under normal

driving conditions draining the crankcase and refilling

with fresh oil every 60 days or every 6000 miles which-

ever occurs first, is recommended.

It is always advisable to drain the crankcase only after

the engine has become thoroughly warmed up or reached

normal operating temperature. The benefit of draining is,

to a large extent, lost if the crankcase is drained when

the engine is cold, as some of the suspended foreign

material will cling to the sides of the oil pan and will not

drain out readily with the cold, slower moving oil.

OIL FILTER

Change engine oil filter every 6000 miles or every 6

months, whichever occurs first.

NOTE:
For Vehicles in heavy duty operation

involving continuous start-stop or prolonged idl-

ing, engine oil should be changed after 2500-

3000 miles of operation. The filter should be

changed after 5000-6000 miles of operation.
Crankcase Dilution

Probably the most serious phase of engine oil deterio-

ration is that of crankcase dilution which is the thinning

of the oil by fuel vapor leaking by pistons and rings and

mixing with the oil and by condensation of water on the

cylinder walls and crankcase.

Leakage of fuel, or fuel vapors, into the oil pan occurs

mostly during the "warming up" period when the fuel is

not thoroughly vaporized and burned. Water vapor enters

the crankcase through normal engine ventilation and

through exhaust gas blow-by. When the engine is not

completely warmed up, these vapors condense, combine

with the condensed fuel and exhaust gases and form acid

compounds in the crankcase.

As long as the gases and internal walls of the crank-

case are hot enough to keep water vapor from con-

densing, no harm will result. However, when the engine

is run in low temperatures moisture will collect and

unite with the gases formed by combustion resulting in

an acid formation. The acid thus formed is likely to

cause serious etching or pitting which will manifest itself

in excessively rapid wear on piston pins, camshaft

bearings and other moving parts of the engine, oftentimes

causing the owner to blame the car manufacturer or the

lubricating oil when in reality the trouble may be traced

back to the character of fuel used, or a condition of the

engine such as excessive blowby or improper carburetor

adjustment.

Automatic Control Devices to Minimize

Crankcase Dilution

All engines are equipped with automatic devices which

aid greatly in minimizing the danger of crankcase

dUution.

The thermostat, mounted in the cylinder head water

outlet, restricts the flow of water to the radiator until a

predetermined temperature is reached, thus minimizing

the length of time required to reach efficient operating

temperature, reducing the time that engine temperatures

are conducive to vapor condensation.

A water by-pass is included in the cooling system,

utilizing a hole in the front of, the cylinder block. This

allows a limited circulation of coolant, bypassing the

thermostat until thermostat opening temperatures are

reached. This system provides a uniform coolant tem-

perature throughout the engine, eliminating localized

hot-spots, improving exhaust valve life, provides fast

warmrup of lubricating oil and fast temperature rise in

the coolant which provides fast heater operation in cold

weather.

A thermostatic heat control on the exhaust manifold

during the warming up period, automatically directs the

hot exhaust gases against the center of the intake mani-

fold, greatly aids in proper vaporization of the fuel.

An automatic choke reduces the danger of raw or

unvaporized fuel entering the combustion chamber and

leaking into the oil reservoir.

An.
efficient crankcase ventilating system drives off

fuel vapors and aids in the evaporation of the raw fuel

and water which may find its way into the oil pan.

CRANKCASE BREATHER CAP

Clean and re-oil at every oil change..

CHEVROLET CHASSIS SERVICE MANUAL

LUBRICATION 0-15

CRANKCASE VENTILATION VALVE

VALVE TYPE

NOTE: Under prolonged dusty driving condi-

tions,
it is recommended that these operations

be performed more often. Every 12,000 miles

or 12 months the valve should be replaced.

Connecting hoses, fittings, flame arrestor and

crankcase breather cap (where used) should be

cleaned. At every oil change the system should

be tested for proper function and serviced, if

necessary.

FUEL FILTER

Replace filter element located in carburetor inlet if

flooding occurs, if engine surges during constant speed

operation (pulsating effect) or if poor performance is

experienced during acceleration or at higher speeds.

AIR CLEANER

NOTE: Under prolonged dusty driving condi-

tions,
it is recommended that these operations

be performed more often.

POLYURETHANE TYPE-

Every 12,000 miles clean element in solvent, squeeze

out solvent, then soak in engine oil and squeeze out

excess.

OIL WETTED PAPER ELEMENT TYPE-

First 12,000 miles inspect or test element; if satis-

factory, re-use element but recheck every 6,000 miles

until replaced. Element must not be washed, oiled,

tapped or cleaned with an air hose.

BATTERY TERMINAL WASHERS

Battery terminals have felt washers between top of

case and cable connections to minimize corrosive action

of battery acid. These felt washers should be saturated

with engine oil every 6,000 miles.

DISTRIBUTOR

4 and 6-Cylinder Engine—Remove distributor cap and

rotate lubricator 1/2 turn at 12,000 mile intervals. Re-

place at 24,000 mile intervals.

8-Cylinder Engine—Change cam lubricator end for end

at 12,000 mile intervals. Replace at 24,000 mile

intervals.

REAR AXLE AND 3-SPEED AND

OVERDRIVE, 4-SPEED TRANSMISSIONS

The passenger car operates under the most severe

lubrication conditions at high speed and requires a hypoid

lubricant which will meet this condition.

Recommended Lubricants

Standard Rear Axles—SAE 90 "Multi-Purpose" gear

lubricant.

Positraction Rear Axles—Use special Positraction

lubricant.
CAUTION: Straight Mineral Oil gear lubricants

must not be used in hypoid rear axles.

Transmissions—SAE 90 "Multi-Purpose" gear

lubricant.

The SAE 90 viscosity grade is recommended for year

round use. However, when extremely low temperatures

are encountered for protracted periods during the winter

months, the SAE 80 viscosity grade may be used.

"Multi-Purpose" Gear Lubricants

Gear lubricants that will satisfactorily lubricate hypoid

rear axles have been developed and are commonly re-

ferred to as ' 'Multi-Purpose" gear lubricants meeting

U.S.
Army Ord. Spec. MIL-L-2105B.

These lubricants can also be satisfactorily used in

manual transmissions.

CAUTION: With Positraction rear axles use

special Positraction lubricant.

"Multi-Purpose" gear lubricants must be manufac-

tured under carefully controlled conditions and the

lubricant manufacturer must be responsible for the

satisfactory performance of his product. His reputation

is the best indication of quality.

Lubricant Additions

The lubricant level in the axle and transmission hous-

ings should be checked periodically. (Every 6,000 miles.)

It is recommended that any additions required to bring

up the lubricant level be made using the same type lubri-

cant already in the housing.

When checking lubricant level in transmission or rear

axle the unit being cheeked should be at operating

temperature. With unit at operating temperature the

lubricant should be level with bottom of the filler plug

hole.
If the lubricant level is checked with the unit cold

the lubricant level should be 1/2 inch below the filler

plug hole.

Lubricant Changes

The rear axle lubricant does not require changing for

the life of the vehicle. If additions are needed, or when

refilling the axle after service procedures, use lubricants

described above.

POWERGLIDE TRANSMISSION

NOTE: Every 12,000 miles, it is recommended

that the Powerglide low band be adjusted as

specified in Section 7 of this manual.

Every 6,000 miles--Check fluid level on dipstick with

engine idling, selector lever in neutral position, parking

brake set and transmission at operating temperature. If

fluid level is below full mark on dip stick, adding a small

amount of Automatic Transmission Fluid, General Motors

Automatic Transmission Fluid (Part Numbers 1050568-

69,
70) is recommended. If this fluid is not obtainable,

use Automatic Transmission Fluid Type 'A' bearing the

mark AQ-ATF followed by a number and the suffix letter

'A'.
Recheck fluid level on dip stick and again add a

small amount of fluid if needed to bring level to full

mark. DO NOT OVERFILL.

CHEVROLET CHASSIS SERVICE MANUAL

HEATER AND AIR CONDITIONING 1A-30

Leak Detector

Tool J-6084 (fig. 43) is a propane gas-burning torch

which is used to locate a leak in any part of the system.

Refrigerant gas drawn into the sampling tube attached to

the torch will cause the torch flame to change color in

proportion to the size of the leak. Propane gas fuel

cylinders used with the torch are readily available

commercially throughout the country.

CAUTION: Do not use lighted detector in any

place where combustible or explosive gases,

dusts or vapors may be present;

Operating Detector

1.
Open control valve only until a low hiss of gas is

heard, then light gas at opening in chimney.

2.
Adjust flame until desired volume is obtained. This

is most satisfactory when blue flame is approxi-

mately 3/8" above reactor plate. The reaction plate

will quickly heat to a cherry red.

3.
Explore for leaks by moving the end of the sampling

hose around possible leak points in the system. Do

not pinch or kink hose.

NOTE: Since R-12 is heavier than air, it is

good practice to place open end of sampling tube

immediately below point being tested, partic-

ularly in cases of small leaks.

CAUTION: Do not breathe the fumes that are

produced by the burning of R-12 gas in the de-

tector flame, since such fumes can be toxic in

large concentrations of R?»12.

4.
Watch for color changes. The color of the flame

which passes through the reaction plate will change

to yellow when sampling hose draws in very small

CHIMNEY

REACTION PLATE

BURNER HEAD

Fig.
43—Leak Detector
leaks of R-12. Large leaks will be indicated by a

change in color to a vivid purplish-blue. When the

sampling hose passes the leak, the flame will clear

to an almost colorless pale-blue again. If the flame

remains yellow when unit is removed from leak,

insufficient air is being drawn in or the reaction

plate is dirty.

NOTE: A refrigerant leak in the high pressure

side of the system may be more easily detected

when, if possible, the system is in operation. A

leak on the low pressure side may be most

easily detected after the engine has been shut

off for several minutes to allow system pres-

sures to equalize. This particularly applies to

the front seal.

VACUUM PUMP

A vacuum pump should be used for evacuating air and

moisture from the air conditioning system.

Vacuum pump, Tool J-5428, (fig.. 44) is available for

this purpose. It is used as a component part of the

Charging Station J-8393, described previously. The fol-

lowing precautions should be observed relative to tbe

operation and maintenance of this pump.

' • Make sure dust cap on discharge outlet of vacuum

pump is removed before operating.

• Keep all openings capped when not in use to avoid

moisture being drawn into the system.

• Oil should be changed after every 250 hours of nor-

mal operation.

To change oil, simply unscrew hex nut located on

back side of pump, tilt backward and drain out oil

(fig. 44). Recharge with 8 ounces of vacuum pump

oil.
If you desire to flush out the pump, use this

same type clean oil. Do not use solvent.

NOTE: Improper lubrication will shorten the

life of pump.

• If this pump is subjected to extreme or prolonged

cold, allow it to remain indoors until oil has reached

approximate room temperature. Failure to warm oil

will result in a blown fuse.

• A five ampere time delay cartridge fuse has been

installed in the common line to protect the windings

of the compressor. The fuse will blow if an ex-

cessive load is placed on the pump. In the event the

fuse is blown, replace with a five ampere time delay

fuse - do not use a substitute fuse as it will result in

damage to the starting windings.

• If the pump is being utilized to evacuate a burnt-out

system, a filter must be connected to the intake

fitting to prevent any sludge from contaminating the

working parts, which will result in malfunction of the

pump.

• Do not use the vacuum pump as an air compressor.

AVAILABILITY OF REFRIGERANT-12

Refrigerant-12 is available through Parts Stock in 25

lb.
drums and in 15 oz. disposable cans. Valves are

available for
the"
disposable cans, which may be used as

individual cans or as a group of up to four cans (fig. 45).

Tool J-6272 is used with one through four cans. The

use of the four-can fixture makes it possible to charge

the system with a known quantity of refrigerant without

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE 6-7

Tune Up should be checked whenever the Air Injection

Reactor System seems to be malfunctioning. Particular

care should be taken in checking items that affect fuel-air

ratio such as the crankcase ventilation system, the car-

buretor and the carburetor air cleaner. Carburetors and

distributors for engines with the Air Injection Reactor

System are designed, particularly, for these engines;

therefore, they must not be interchanged with or replaced

by a carburetor or distributor designed for an engine

without the Air Injection Reactor System.

Choke Adjustment (Fig. 11)

With Remote Choke

1.
Remove air cleaner and check to see that choke

valve and rod move freely.

2.
Disconnect choke r*od at choke lever.

Check choke adjustment as follows:

On all except 275 hp 327 cu. in. engines, hold

choke valve closed and pull rod up against stop. The

top of choke rod end should be 1/2 - 1 rod diameter
4.

5.
above top of hole in choke valve lever.

On 275 hp 327 cu. in. engines, hold choke valve

closed and push rod down against stop on thermostat

bracket. The top of the choke rod should be 1/2 - 1

rod diameter below the top of the hole in the choke

lever.

If necessary, adjust rod length by bending rod at off-

set. (Bend must be such that rod enters choke lever

hole freely and squarely.)

Connect rod at choke lever and install air cleaner.

3.
With Manual
Choke

1.
Remove air cleaner.

2.
Push hand choke knob in to within 1/8" of instrument

panel.

3.
Loosen choke cable at carburetor bracket and adjust

cable through the clip until the choke valve is wide

open.

4.
Tighten cable clamp at carburetor bracket and check

operation of choke valve to ensure full closed and

wide open positions.

INSTRUMENT CHECK-OUT

Instrument Hook Up

Connect vacuum gauge, dwell meter, tachometer and

timing light as recommended by the manufacturer of the

equipment being used.

Check and Adjust Dwell

1.
Start engine then ch^ck ignition dwell.

.2.
If dwell is not within specifications, adjust dwell as

follows:

V8 ENGINES

• With engine running at idle, raise the adjustment

screw window-and insert an Allen wrench in the

socket of the adjusting screw (fig. 12).

• Turn the adjusting screw as required until a dwell

reading of 30° is obtained. A 2° variation is al-

lowable for wear.

• Close access cover fully to prevent the entry of

dirt into the distributor.

NOTE: If a dwell meter is not available, turn
adjusting screw clockwise until engine starts to

misfire, then turn screw one-half turn in the op-

posite direction to complete adjustment.

IN LINE ENGINES

• Remove distributor cap and recheck point setting.

If dwell is still not within specifications check the

distributor as outlined in Section 6Y.

Check Dwell Variation

Slowly accelerate engine to 1500 rpm and note dwell

reading. Return engine to idle and note dwell reading. If

dwell variation exceeds specifications, check for worn

distributor shaft, worn distributor shaft bushing or loose

breaker plate.

WINDOW

"HEX" TYPE

WRENCH

Fig.
12 - Setting Point Dwell (V8)
Fig.
13 - Ignition Timing Marks

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE 6-11

Fig.
18 - Cooling System Pressure Test

Carburetor

Refer to Section 6M to perform adjustments such as

idle vent, float level, pump rod and secondary valve.

Fuel Pump

If the owner has complained of poor high speed per-

formance, the fuel pump may be at fault. Too low a

pump pressure or volume will cause a high speed "miss"

because of lack of fuel delievered to the carburetor,

while too high a pressure will cause carburetor flooding.

Check fuel pump as outlined in Section 6M.

Cooling System

The following test may be performed with pressure

testing equipment available commercially for this pur-

pose.
This test provides an excellent means of detecting

internal or external leaks within the cooling system.

1.
Remove radiator cap.

2.
Apply a test pressure of 3 pounds higher than the ra-

diator cap (fig. 18). i.e. 18 pounds for a 15 pound

cap.

3.
If the pressure will not hold, there is either an

internal or external leak in the system.

Cylinder Head Torque and Valve Adjustment

Retorquing the cylinder head bolts is not necessary

unless a gasket has been replaced, or a leak is suspected.

Valve lash must always be adjusted after the head has

been torqued.

Before adjusting the valve lash, it is extremely impor-

tant that the engine be thoroughly warmed up to normal-

ize the expansion of all parts. This is very important

because during the warm-up period, the valve clearances

will change considerably.

Hydraulic

1.
After the engine has been normalized, remove rocker

arm covers and gaskets.

CAUTION: Do not pry rocker arm cover loose.
Gaskets adhering to cylinder head and rocker

arm cover may be sheared by bumping end of

rocker arm cover rearward with palm of hand

or a rubber mallet.

2.
With the engine running at idle, back off valve rocker

arm nut until the valve rocker arm starts to clatter.

3.
Turn rocker arm nut down slowly until the clatter

just stops. This is the zero lash position.

4.
Turn nut down 1/4 additional turn and pause 10 sec-

onds until engine runs smoothly* Repeat additional

1/4 turns, pausing 10 seconds each time, until nut

has been turned down 1 full turn from the zero lash

position.

NOTE: This 1 turn preload adjustment must be

done slowly to allow the lifter to adjust itself to

prevent the possibility of interference, between

the inlet valve head and top of piston, which

might result in internal damage and/or bent push

rods.
Noisy lifters should be replaced.

5.
Repeat Steps 2, 3 and 4 to adjust the rest of the

valves.

6. Clean gasket surfaces on cylinder heads and rocker

arm covers with degreaser then install rocker arm

covers, using new gaskets, and torque bolts to

specifications.

Mechanical

1.
Normalize the engine.

2.
Remove rocker arm covers and gaskets.

CAUTION: Do not pry rocker arm cover loose.

Gaskets adhering to cylinder head and rocker

arm cover may be sheared by bumping end of

rocker arm cover rearward with palm of hand

or a rubber mallet.

3.
Use a socket wrench on self-locking rocker arm stud

nut and adjust as needed to obtain valve lash (see

tune up chart) measured between rocker arm and

valve stem with a leaf type feeler gauge.

4.
Stop engine, clean gasket surfaces on cylinder heads

and rocker arm covers with degreaser then install

rocker arm covers, using new gaskets, and torque

bolts to specifications.

Fig.
19
- Oil Deflector Clips Installed

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE 6-37

Fig.
27V—Removing Camshaft

4.
Set dial indicator on zero, then rotate the damper

slowly, or attach an auxiliary starter switch and

"bump" the engine over, until the push rod is in the

fully raised position.

CAUTION: The primary distributor lead must

be disconnected from the negative post on the

coil and the ignition switch must be in the on

position. Failure to do this will result in a dam-

aged grounding circuit in the ignition switch.

5.
Compare the total lift recorded from the dial indica-

tor with specifications.

6. Continue to rotate the crankshaft until the indicator

reads zero. This will be a check on the accuracy of

the original indicator reading.

7.
If camshaft readings for all lobes are within specifi-

cations, remove dial indicator assembly.

8. Install and adjust valve mechanism as outlined.

Removal

1.
Remove valve lifters as outlined.

2.
Remove crankshaft front cover as outlined.

3.
Remove grille as outlined in Section 13.

4.
Remove fuel pump push rod as outlined * in Sec-

tion 6M.

5.
Complete camshaft removal as follows:

CAUTION: All camshaft journals are the same

diameter and care must be used in removing

camshaft to avoid damage to bearings.

Remove camshaft sprocket to camshaft bolts then

remove sprocket and timing chain together. Sprocket

is a light fit on camshaft. If sprocket does not come

off easily a light blow on the lower edge of the

sprocket (with a plastic mallet) should dislodge the

sprocket.

Install two 5/16" - 18 x 4" bolts in camshaft bolt

holes then remove camshaft (fig. 27V).

Installation

NOTE: Whenever a new camshaft is installed
CONVERTER

BOLT AREA -

DEPRESSED

SYNCHROMESH
RING

GEAR

TRANS.,

AUTOMATIC

Fig.
28V - Flywheel Installation (Typical)

coat camshaft lobes with Molykote or its

equivalent.

1.
Lubricate camshaft journals with engine oil and in-

stall camshaft.

2.
Install timing chain on camshaft sprocket. Hold the

sprocket vertical with the chain hanging down, and

orient to align marks on camshaft and crankshaft

sprockets. Refer to Figure 20V.

3.
Align dowel in camshaft with dowel in hole in cam-

shaft sprocket then install sprocket on camshaft.

Refer to Figure 25V.

4.
Draw the camshaft sprocket onto camshaft using the

mounting bolts. Torque to specifications.

5.
Lubricate timing chain with engine oil.

6. Install fuel pump push rod as outlined in Section 6M.

7.
Install grille as outlined in Section 13.

8. Install crankcase front cover as outlined.

9. Install valve lifters as outlined.

FLYWHEEL

Removal

With transmission and/or clutch housing and clutch

removed from engine, remove the flywheel.

Installation

1.
Clean the mating surfaces of flywheel and crankshaft

to make certain there are no burrs.

2.
Install flywheel on crankshaft and position to align

dowel hole of crankshaft flange and flywheel (fig.

28V).

NOTE: On Automatic Transmission equipped

engines, the flywheel must be installed with the

flange collar to transmission side (fig. 33V).

ENGINE MOUNTS

Engine mounts (fig. 34V) are the nonr adjustable type

and seldom require service. Broken or deteriorated

mounts should be replaced immediately, because of the

added strain placed on other mounts and drive line

components.

Front Mount Replacement

1.
Remove nut, washer and engine mount through-bolt.

2.
Raise engine to release weight from mount.

3.
Remove mount from engine.

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE FUEL 6M-7

5. On vehicles equipped with automatic transmission

hold throttle rod in full throttle position, pull TV

rod to full detent position and adjust TV rod to just

enter hole on throttle lever, then connect TV rod at

throttle lever.
NOTE:
If equipped with anti-stall device (dash-

pot),
set carburetor fast idle cam on high step

and adjust dash-pot to just contact throttle

lever.

327
CU.
IN.
427
CU.
IN.

Fig.
8C—Throttle Linkage-Corvette

AIR
CLEANERS

INDEX

Page

General Description 6M-7

Service Procedures . . 6M-8

Polyurethane. Element 6M-8

Maintenance 6M-8

Oil Bath 6M-8
Page

Maintenance
...........* 6M-8

Oil
Wetted
Paper
Element
6M-9

Replacement
* . 6M-9

Testing 6M-9

Tool J-7852 . 6M-9

GENERAL DESCRIPTION

Air cleaners on all models operate primarily to re-

move dust and dirt from the air that is taken into the

carburetor and engine. All air cleaners on engines

equipped with "Closed Positive" ventilation incorporate

flame arresters. Every 12,000 miles the flame ar-

resters should be removed, cleaned in solvent and blown

dry with compressed air.

An oil wetted polyurethane element air cleaner (fig. 1A)

is standard equipment on In Line engines. This type

cleaner element is reusable and should be removed,

cleaned, re-oiled and reinstalled every 12,000 miles or

more often during dusty or other adverse driving con-

ditions. The optional, oil bath air cleaner (available on
Chevrolets with L6 engine) should be cleaned and re-

filled with oil at oil change intervals.

On the V8 engines,, a replaceable, oil wetted paper

element type is used (fig; 2A). Both ends of me paper

element are bonded with plastisol sealing material.

The improved oil wetted paper elements have increased

filtering capacity over their dry paper predecessors.

Oil on the paper causes the element to become diBcolored

by a small amount of dirt but does not necessarily mean

the element is plugged or reduced in efficiency. Every

12,000 miles or more often during dusty or other adverse

driving conditions, either replace oil wetted paper ele-

ment or test element using ToolJ-7825.

CHEVROLET CHASSIS SOVICE/MANUAL