1967 CHEVROLET CAMARO electrical

CLUTCH AND TRANSMISSIONS 7-10 ,

GENERAL DESCRIPTION

The overdrive unit is essentially a two-speed planetary-

transmission attached to the rear of a conventional three-

speed transmission. In overdrive, engine speed is ap-

proximately 30 per cent slower at a given road speed

since the drive train includes planetary gears which pro-

vide a lower overall gear ratio than that obtained in high

gear with the conventional transmission.

The electrical equipment which controls the automatic

action of the mechanical portion of the overdrive unit

consists of a solenoid, a speed-sensitive governor switch,

a relay and a kickdown switch. The circuit including this

equipment makes it possible to operate in overdrive above

a pre-set cut-in speed, or in .conventional drive at any

speed.

With the overdrive unit engaged, the transmission

should not be left in any forward gear with intent of lock-

ing the drive-line as the overrunning clutch is a free-

wheeling condition.
SERVICING THE OVERDRIVE

With the,overdrive assembly removed from the trans-

mission, service operations on the transmission proper

are the same as for the standard three-speed trans-

mission.

Repairs to the overdrive housing, output shaft, ring

gear assembly, clutch cam, roller retainer, pinion cage,

sun gear, shift rail, sun gear control plate, output shaft

bearing, oil seal, speedometer drive gear, solenoid pawl

and interlock plunger may be performed underneath the

car, if so desired, by removing the overdrive housing

without disturbing the transmission. Refer to Overhaul

Manual for Service Procedure.

If the transmission mainshaft, overdrive adapter or

transmission rear bearing which is retained in adapter

require replacement, the entire transmission and over-

drive assembly should be removed and overhauled on the

bench.

MAINTENANCE AND ADJUSTMENTS

Servicing of the overdrive governor switch and pinion,

the sun gear solenoid, oil seal and cable bracket, the out-

put shaft rear oil seal, the control shaft lever, and the

speedometer driven gear may be accomplished without

removing the overdrive from the vehicle, as discussed

in the following paragraphs:

GOVERNOR SWITCH AND PINION

To remove governor switch, disconnect wires at gover-

nor switch and screw governor
out
of housing, using Tool

J-4653 on the flat hexagonal surface of governor case.

The pinion may be separated from the governor by re-

moving the snap ring on the shaft.

SUN GEAR SOLENOID, OIL SEAL AND

CONTROL CABLE BRACKET

Remove the solenoid by taking out the two mounting

bolts and lock washers, removing
the.
cable bracket with

the lower bolt. Turn the solenoid 1/4 turn and
pull,
sole-

noid plunger out of adapter. The oil seal may be pried

out of the adapter.

CASE REAR OIL SEAL

Removal

1.
Remove propeller shaft as outlined in Section 4.

2.
Using a punch against seal in housing, pry out seal

from housing.

Installation

1.
Prelubricate between sealing lips and coat outside of

new oil seal with a suitable sealant, then start seal

into bore in overdrive housing.

2.
Using Tool J-5154 drive oil seal into counterbore.

3.
Install propeller shaft as outlined in Section 4.

CONTROL SHAFT LEVER AND/OR "O" RING

OIL SEALS

To remove- the control shaft, disconnect the cpntrol
cable, remove tapered pin and pull lever out. Replace

the two "0" ring seals on the control shaft. Insert shaft

and new "O" ring seals into housing and install tapered

pin. Connect control wire to lever.

SPEEDOMETER DRIVEN GEAR

Disconnect speedometer cable, remove lock plate to

housing bolt and lock washer and remove lock plate. In-

sert screw driver in lock plate slot in fitting and pry

fitting, gear and shaft from housing. Pry "O" ring from

groove in guide.

Install new "O" ring in groove in fitting and insert

shaft.

Hold the assembly so slot in fitting is toward lock plate

boss on housing and install in housing. Push fitting into

housing until lock plate can be inserted in groove and

attached to housing.

L
dl

ZAIR GAP

km (CHECK WITH

M*= POINTS BARELY
'A

AoWER
|^

POINT

0 ADJUST

=^ i
SUPPORT

Fig. IB - Checking Relay Air Gap

CHEVROLET CHASSIS SERVICE MANUAL

CLUTCH AND TRANSMISSIONS 7-11

UPPER ARMATURE STOP

(BEND TO ADJUST POINT OPENING)

Fig.
2B-Adjusting Relay Point Opening

ELECTRICAL UNIT CHECKS

Overdrive Relay

Specifications and checking procedures for this relay

are as follows:

Specifications

Air Gap Oil inch minimum

Point Opening .025 inch

Closing Voltage
8.3-10.2
volts

Armature Sealing Voltage. ..... 11.2 volts maximum

Three checks and adjustments are required on the

overdrive relay; air gap, point opening and closing volt-

age.
The air gap contact point opening checks and adjust-

ments should be made with the battery disconnected.

Air Gap

The air gap should not normally require adjustment

unless the relay has been misadjusted. Check the air gap

with the points barely touching and adjust if necessary by

bending the lower point support (fig, IB).

Point Opening

Check the contact point opening and adjust by bending

the upper armature stop (fig. 2B).

Closing Voltage

To check the relay closing voltage, connect a potenti-

ometer or variable resistance of sufficient value (not less

than 50 ohms) in series with the "KD" terminal, connect a

voltmeter to the "IGN" and "KD" terminals. With the

ignition switch on, slowly decrease the amount of resist-

ance in order to check the relay closing voltage (the

overdrive solenoid and relay should click when the relay

closes). Adjust the closing voltage by bending the arma-

ture spring post (fig. 3B). Bend down to increase the

closing voltage and bend up to decrease the closing

voltage.

To check the sealing voltage, increase the voltage after

the relay closes until the armature seals against the

core.
Decrease the sealing voltage by reducing the relay

air gap.

Solenoid

Closing Coil

Remove solenoid from transmission, connect a jumper

wire between negative terminal of battery and mounting

flange of solenoid. Connect a second jumper wire be-
ARMATURE SPRING PQST

(BEND TO ADJUST CLOSING VOLTAGE)

Fig.
3B - Adjusting Relay Closing Voltage

tween the battery positive terminal and solenoid terminal

No.
4; this should cause the solenoid pawl to move out.

If solenoid chatters, Hold-In Coil is defective.

Engaging Spring

With jumper wire connected as in paragraph above,

(solenoid energized, plunger extended) place ball end of

solenoid against bench. Push down on solenoid. The

pawl rod should move in 3/8M under a load of not less

than 8 lbs. nor more than 12. Pawl should move out to

extended position when load is removed.

Ignition Grounding Contact

Place a test lamp between negative battery terminal

and solenoid terminal No. 6. Lamp should light when this

connection is made. Remove jumper from between nega-

tive battery terminal and solenoid terminal No. 4. Pawl

rod should snap "in" and test lamp should go out.

Governor Switch

Remove overdrive wire at governor and connect test

lamp between governor overdrive terminal and positive

terminal of battery. Drive car on road or raise on jacks.

The lamp should light at a car speed of between 26 to 30

MPH. Upon decreasing speed, the lamp should go out at

between 28 and 23.5 MPH. The car speed differential

between light "on" and light "off" should be 2 or 3 MPH.

Kickdown Switch

Disconnect the 4 wires at kickdown switch.

1.
Connect test lamp between "SW" terminal and posi-

tive terminal of battery; with switch in normal posi-

tion, lamp should light when "REL" terminal is

grounded but should not light when "IGN" or "SOL"

terminals or switch case is grounded.

2.
Connect test lamp between "IGN" terminal and posi-

tive terminal of battery; with switch stem pushed in,

lamp should light when "SOL" terminal is grounded,

but should not light when "SW" or "REL" terminals

or switch case is grounded.

CHEVROLET CHASSIS SERVICE MANUAL

CLUTCH AND TRANSMISSIONS 7-13

PULL-IN

WINDING
li
HOLD-IN

WINDING

Fig.
4B -
Overdrive Electrical Circuit Wiring Diagram

ELECTRICAL

Any one of the following general complaints may be due

to electrical trouble in the overdrive circuit.

1.
Does not engage.

2.
Does not release.

3.
Does not kickdown from overdrive.

These troubles may be traced and remedied as de-

scribed in the following paragraphs.

1.
Does not engage

a. With the ignition switch on, ground the "KD" ter-

minal of the solenoid relay with a jumper lead.

If the solenoid clicks, the relay and solenoid cir-

cuits are in operating condition. If no click is

heard in the relay, check the fuse and replace if

defective.

b.
If the fuse is good, use a second jumper lead to

connect the "SOL" and "BAT" terminals of the

relay. If a click is now heard in the solenoid, the

relay is probably at fault and should be repaired

or replaced.

c. If the solenoid does not click in Step b, check the

wiring to the No. 4 terminal of the solenoid and

replace if necessary. If the wiring is not defec-

tive,
the trouble is probably in the solenoid. Re-

move the solenoid cover, examine the solenoid

contacts in series with the pull-in winding and

clean if necessary. Test again for clicks, as in

Step b, after replacing solenoid cover and lead

wires.
Replace the solenoid if trouble has not

been corrected.

d. If the relay and solenoid circuits are in good con-

dition as determined in Step a, leave the ignition

switch on and make sure the manual control knob

is in the overdrive position. Ground one and then

the other of the two terminals next to the stem of

the kickdown switch (identified as "SW" and
?fREL"). K the solenoid clicks when one terminal

is grounded but not the other, replace the switch.

If the solenoid does not click when either of the

terminals is grounded, check the wiring between

the relay and the kickdown switch and replace if

defective.

e. If the solenoid clicks as each terminal is grounded

in Step d, ground the governor switch terminal.

If the solenoid clicks, the governor switch may be

defective. If the solenoid does not click, check

the wiring between the kickdown and governor

switches and replace if necessary.

2.
Does not release

a. Remove the connection to the "KD" terminal of

the relay. If this release overdrive, look for a

grounded control circuit between the relay and

governor switch.

b.
If the overdrive is not released in Step a, dis-

connect the lead to the "SOL" terminal of relay.

If this releases the overdrive, replace the relay.

3.
Does not kickdown from overdrive

a. With the engine running, connect a jumper lead

between the No. 6 terminal of the solenoid and

ground. Operate the kickdown switch by hand.

This should stop the engine. If it does, the sole-

noid is probably defective and it should be checked

for dirty ground-out contacts or other defects

within the ground-out circuit of the solenoid (fig.

4B).
Clean the contacts or replace the contact

plate as required.

b.
If the engine does not stop in Step a, ground one

and then the other of the two terminals (Identified

as "IGN" and "SOL") farthest from the sfem of

the kickdown switch. The engine should stop when

one of the two terminals (IGN) is grounded. If

the engine does not stop when the terminal is

grounded, the wiring or connections to the switch

between the switch and coil are defective. When

the btlier terminal (SOL) is grounded, the engine

should stop when the kickdown switch is operated.

If the engine does not stop when the kickdown

switch is operated with the second terminal

grounded, the kickdown switch is defective. If

the trouble is in the kickdown switch, adjust the

linkage to give more travel of the switch rod.

If this does not correct the trouble, replace the

kickdown switch.

If the kickdown switch operates as it should,

check for an open circuit in the wiring between

the kickdown switch and the No. 6 terminal of the

solenoid.

c. If the trouble is not located by the above checks,

the upper contacts of the kickdown switch may not

be opening. To check for this condition, ground

the overdrive control circuit at the governor

switch. This should cause the solenoid to click.

Operate the kickdown switch by hand. This should

cause a second click as the solenoid releases.

If there is no second click, adjust the linkage to

give more travel of the switch rod. If this does

not correct the trouble, replace the kickdown

switch.

CHEVROLET CHASSIS SERVICE MANUAL

CLUTCH AND TRANSMISSIONS
7*30

V-8 Models-With Uni-Directional Linkage

1.
Remove air cleaner.

2.
Disconnect accelerator linkage at carburetor.

3.
Disconnect accelerator return and TV rod return

springs.

4.
With right hand, pull TV upper rod forward until

transmission is through detent. With left hand, open

carburetor to wide open throttle position. Carbure-

tor must reach wide open throttle position at the

same time the ball stud contacts end of slot in upper

TV rod.

5. Adjust swivel on end of upper TV rod to obtain set-

ting described in Step 4. Allowable tolerance is

approximately 1/32".

6. Connect and adjust accelerator linkage as described

in Section 6.

7. Check for throttle linkage freedom.

Neutral Safety Switch Adjustment

The adjustment at the neutral safety switch is de-

scribed in the Electrical Section 12.

Throttle Return Check Valve (Dashpot) Adjustment

The adjustment of the throttle return check valve is

described in Section 6M for each carburetor installation.
Fig.
12PG - Floor Mounted Control Lever and

Bracket Assembly (Chevrolet Shown)

COMPONENT PARTS REPLACEMENT

TRANSMISSION REPLACEMENT (EXC. CORVETTE)

Removal

1.
Raise car on hoist (preferably) or on stand jack and

remove oil pan drain plug to drain oil.

NOTE:
If desired, the oil may be drained after

transmission removal.

2.
Disconnect the oil cooler lines (external cooled

models), vacuum modulator line and the speedometer

drive cable fitting at the transmission. Tie lines

out of the way.

3.
Disconnect manual and TV control lever rods from

transmission.

4.
Disconnect propeller shaft from transmission.

5. Install suitable transmission lift equipment to jack

or other lifting device and attach on transmission.

6. Disconnect engine rear mount on transmission ex-

tension, then disconnect the transmission support

crossmember and slide rearward.

7. Remove converter underpan, scribe flywheel-con-

verter relationship for assembly, then remove the

flywheel-to-converter attaching bolts.

NOTE:
The "light" side of the converter is

denoted by a "blue" stripe painted across the

ends of the converter cover and housing. This

marking should be aligned as closely as possible

with the "white" stripe painted on the. engine

side of the flywheel outer rim (heavy side of

engine) to maintain balance.

8. Support engine at the oil pan rail with a jack or other

suitable brace capable of supporting the engine

weight when the transmission is removed.
9. Lower the rear of the transmission slightly so that

the upper transmission housing-to-engine attaching

bolts can be reached using a universal socket and a

long extension. Remove upper bolts.

CAUTION: Oh V-8 engines, care must be taken

not to lower rear of transmission too far as the

distributor housing may be forced against the

dash causing damage to the distributor. It is

best to have an assistant observe clearance of

all upper engine components while the trans-

mission rear end is being lowered.

10.
Remove remainder of transmission housing-to-

engine attaching bolts.

11.
Remove the transmission by moving it slightly to the

rear and downward, then remove from beneath the

car and transfer to a work bench.

NOTE:
Observe converter when moving the

transmission rearward. If it does not move

with the transmission, pry it free of flywheel

before proceeding.

CAUTION: Keep front of transmission upward

to prevent the converter from falling out. Install

converter Tool J-9549 (or a similar tool con-

structed as shown in Figure 13PG, or, in an

emergency, a length of strong wire may be used)

immediately after removal from the engine.

Installation

NOTE:
The "light" side, of the converter is

denoted by a "blue" stripe painted across the

ends of the converter cover and housing. This

marking should be aligned as closely as possible

CHEVROLET CHASSIS SERVICE MANUAL

CLUTCH AND TRANSMISSIONS 7-36

TURBO HYDRA-MATIC TRANSMISSION

INDEX

Page

General Description . . , . 7-36

Maintenance and Adjustments . 7-37

Transmission Fluid 7-37

Fluid Level Indicator 7-37

Shift Control Linkage Adjustment ........... 7-37

Neutral Safety Switch Adjustment 7-37

Draining and Refilling Transmission . . . 7-37

Pressure Regulator Valve 7-38

Control Valve Body . 7-39

Governor ..'.... 7-40

Modulator and Modulator Valve 7-40

Parking Linkage . . 7-40
Page

Rear Seal -. 7-40

Other Service Operations . . 7-40

Transmission Replacement 7-40

Turbo Hydra-Matic Diagnosis Procedure. ......... 7-41

Sequence . ; ; 7-41

Oil Level and Condition Check 7-41

Manual Linkage 7-41

Oil Leaks .' 7-41

Case Porosity - Repair ................ 7-42

Oil Pressure Check 7-42

Transmission Shift Points 7-42

Special Tools 7-43

GENERAL DESCRIPTION

The Turbo Hydra-Matic transmission is a fully auto-

matic unit consisting primarily of a 3-element hydraulic

torque converter and a compound planetary gear set.

Three multiple-disc clutches, one sprag unit, one roller

clutch and two bands provide the friction elements re-

quired to obtain the desired function of the compound

planetary gear set.

The torque converter couples the engine to the plane-

tary gears through oil and provides hydraulic torque

multiplication when required. The compound planetary

gear set produces three forward speeds and reverse.

The
3-
element torque converter consists of a pump or

driving member, a turbine or driven member, and a

stator assembly. The stator is mounted on a one-way

roller clutch which will allow the stator to turn clock-

wise but not counter-clockwise.

The torque converter housing is filled with oil and

is attached to the engine crankshaft by a flex plate and

always rotates at engine speed. The converter pump is

an integral part of the converter housing, therefore the

pump blades, rotating at engine speed, set the oil within

the converter into motion and direct it to the turbine,

causing the turbine to rotate.

As the oil passes through the turbine it is traveling in

such a direction that if it were not re-directed by the

stator it would hit the rear of the converter pump blades

and impede its pumping action. So at low turbine speeds,

the oil is re-directed by the stator to the converter pump

in such a manner that it actually assists the converter

pump to deliver power or multiply engine torque.

As turbine speed increases, the direction of the oil

leaving the turbine changes and flows against the rear

side of the stator vanes in a clockwise direction. Since

the stator is now impeding the smooth flow of oil, its

roller clutch releases and it revolves freely on its shaft.

Once the stator becomes inactive, there is no further

multiplication of engine torque within the converter. At

this point, the converter is merely acting as a fluid

coupling as both the converter pump and turbine are

being driven at approximately the same speed - or at a

one-to-one ratio.

A hydraulic system pressurized by a gear type pump

provides the working pressure required to operate the

friction elements and automatic controls.

External control connections to transmission are:
Manual Linkage

Engine Vacuum

12 Volt Electrical

Signal
To select the desired op-

erating range.

To operate a vacuum mod-

ulator unit.

To operate an electrical

detent solenoid.

A vacuum modulator is used to automatically sense

any change in the torque input to the transmission. The

vacuum, modulator transmits this signal to the pressure

regulator for line pressure control, to the 1-2 accumula-

tor valve, and to the shift valves so that all torque re-

quirements of the transmission are met and smooth

shifts are obtained at all throttle openings.

The detent solenoid is activated by an alectric switch

on the carburetor. When the throttle is fully opened, the

switch on the carburetor is closed, activating the detent

solenoid and. causing the transmission to downshift at

speeds below approximately 70 MPH.

The selector quadrant has six selector positions: P,R,

N,D,
L2,L1.

P.
*
- Park position positively locks the output shaft to

the transmission case by means of a locking pawl

to prevent the vehicle from rolling in either di-

rection. The engine may be started in Park

position.

R. - Reverse enables the vehicle to be operated in a

reverse direction.

N.
- Neutral position enables the engine to be started

and run without driving the vehicle.

D,
- Drive Range is used for all normal driving condi-

tions and maximum economy. Drive Range has

three gear ratios, from the starting ratio to

direct drive. Detent downshifts are available by

depressing the accelerator to the floor.

L2.
- L2 Range has the same starting ratio as Drive

Range, but prevents the transmission from shift-

ing above second speed to retain second speed

acceleration when extra performance is desired.

L2 Range can also be used for engine braking.

L2 Range can be selected at any vehicle speed,

and the transmission will shift to second gear and

remain in second until the vehicle speed or the

throttle are changed to obtain first gear operation

in the same manner as in D Range.

CHIVROLET CHASSIS SERVICE MANUAL

CLUTCH AND TRANSMISSIONS 7-40

pipes.
If
care
is
taken
in
removing control valve

body
the six (6)
check balls will stay
in
place above

the spacer plate.

CAUTION:
Do not
drop manual valve.

5. Remove
the
governor pipes
and
manual valve from

control valve body.

Installation

Installation
of the
control valve body
is the
reverse
of

the removal.

GOVERNOR

Removal
.

1.
Remove governor cover attaching screws, cover,
and

gasket.

2.
Discard gasket.

3.
Withdraw governor assembly from case.

Installation

Installation
of the
governor assembly
is the
reverse
of

the removal.
Use a new
gasket under
the
governor

cover.

MODULATOR AND MODULATOR VALVE

Removal

1.
Remove modulator assembly attaching screw
and

retainer.

2.
Remove modulator assembly from case. Discard

"O"
ring seal.

3.
Remove modulator valve from case.

Installation

Installation
of the
modulator assembly
and
modulator

valve
is the
reverse
of the
removal.
Use a new
"O" ring

seal
on the
modulator assembly.
PARKING LINKAGE

Removal

1.
Remove bottom
pan and oil
strainer.

2.
Unthread
jam nut
holding detent lever
to
manual

shaft.

3.
Remove manual shaft retaining
pin
from case.

4.
Remove manual shaft
and jam nut
from case.

NOTE:
DO NOT
remove manual shaft seal
un-

less replacement
is
required.

5. Remove parking actuator
rod and
detent lever
as-

sembly.

6. Remove parking pawl bracket attaching screws
and

bracket.

7. Remove parking pawl return spring.

NOTE:
The
following steps should
not be com-

pleted unless part replacement
is
required.

8. Remove parking pawl shaft retainer.

9.
Remove parking pawl shaft,
cup
plug, parking pawl

shaft, and parking pawl.

Installation

Installation
of the
parking linkage
is the
reverse
of the

removal.
Use new
seal
and cup
plug,
if
removed,
and

new bottom
pan
gasket.

REAR SEAL

Removal

1.
Remove propeller shaft.

2.
Pry
seal
out
with screw driver.

Installation

1.
Using Tool J-5154
or
J-21359 install
new
seal.

2.
Re-install propeller shaft.

OTHER SERVICE WITH TRANSMISSION IN VEHICLE

The following operations when done
as
single opera-

tions
and not as
part
of a
general overhaul should,
as a

practical matter,
be
performed with
the
transmission
in

the.
vehicle. Refer
to the
"Transmission Disassembly

and Reassembly" section
of the
Overhaul Manual
for

service procedures.

a. Oil
filler pipe
and
"O"
ring seal.

b.
Oil pan
and
gasket.

c. Down shift solenoid
or
connector.
d. Valve body spacer plate, gasket
and
check balls.

e. Front accumulator piston.

f.
Rear servo
and
rear accumulator assembly.

g.
Rear band apply checking with Tool J-21370.

Ji.
Front servo assembly.

i. Speedo driven gear.

j.
Case extension
or
gasket.

k.
Strainer
and
"O"
ring.

TRANSMISSION REPLACEMENT

Before raising
the car,
disconnect
the
battery
and re-

lease
the
parking brake.

1.
Remove propeller shaft.
8.

2.
Disconnect speedometer cable, electrical lead to case
9.

connector, vacuum line
at
modulator,
and oil
cooler
10.

pipes.

3.
Disconnect shift control linkage.

4.
Support transmission with suitable transmission jack.
11.

5. Disconnect rear mount from frame crossmember.

6. Remove
two
bolts
at
each
end of
frame crossmember
12.

and remove crossmember.

7. Remove
oil
cooler lines, vacuum modulator line,
speedo cable,
and
detent solenoid connector wire
at

transmission.

Remove converter under
pan.

Remove converter
to
flywheel bolts.

Loosen exhaust pipe
to
manifold bolts approximately

1/4
inch,
and
lower transmission until jack
is
barely

supporting
it.

Remove transmission
to
engine mounting bolts
and

remove
oil
filler tube
at
transmission.

Raise transmission
to its
normal position, support

engine with jack
and
slide transmission rearward

from engine
and
lower
it
away from vehicle.

CHEVROLET CHASSIS SERVICE MANUAL

CHASSIS SHEET METAL 11-4

FENDERS

Fenders are adjustable with shims at the cowl and

rocker panel. To add or remove shims, loosen bolts at

shim locations (fig. 7) and carefully apply force with pry

bar to provide clearance for shim removal or installa-

tion.
SHEET METAL ADJUSTMENTS

For proper operation of doors and hood, and for pre-

sentable appearance, adjust front sheet metal to the tol-

erances shown in Figures
4-
and 5.

COMPONENT PART REPLACEMENT

NOTE: When replacing sheet metal compo-

nents on Chevrolet or Chevelle, note position and

attachment of all seals and dust shielding and

replace as necessary.

BATTERY TRAY

Removal

1.
Disconnect battery cables.

2.
Remove screw retaining battery hold down clamp and

remove battery from vehicle.

3.
Remove screws retaining battery tray to fender skirt

and radiator support.

4.
On Chevrolet, remove headlamp bezel and remove

screw retaining tray to radiator support.

5.
Remove battery tray from vehicle.

Installation

Reverse removal procedure.

RADIATOR SUPPORT

Removal

1.
Remove front bumper (Section 14).

Fig.
3 - Hood Hinge - Chevrolet
2.
Remove grille and related components (Section 13).

3.
Remove battery tray as outlined above.

4.
Remove all electrical connections from radiator

support.

5.
Remove windshield washer bottle from bracket on

radiator support.

6. Remove shroud and radiator (Section 13).

7.
Remove screws and bolts securing support to skirts,

fenders, and frame horns (figs. 8 and 9).

8.. Spread fenders apart enough to allow support move-

ment and remove support from front of vehicle.

Installation

1.
Position the radiator support in vehicle", aligning

mounting screw and bolt holes with drift punch.

2.
install screws and bolts loosely until all are started.

3.
Replace all parts removed following removal proce-

dure in reverse order.

4.
Refer to torque specifications in rear of manual for

correct torque values.
•

5.
Aim headlamps as outlined in Section 12.

FENDER ASSEMBLY

Removal

1.
Remove hood with hinges from vehicle as outlined in

this section.

2.
On Chevrolet models, remove headlamp bezels and

headlamps; on Chevelle models, remove grille ex-

tension panels (fig. 1 or 2 as applicable).

3.
Disconnect wiring harness clips from fender to be

removed.

4.
If applicable, remove horn assembly from fender.

5.
If applicable, remove radio antenna.

6. Remove fender brace (fig. 1 or 2 as applicable).

7.
Remove screws retaining fender to radiator support,

skirt, cowl, filler panel, tie bar, and rocker panel.

Note number and location of shims removed from

locations shown in Figure 7.

8. Remove fender from vehicle.

Installation

Refer to disassembly procedure for location of screws

and install screws loosely. Install the shimmed screws

at rocker panel and cowl and adjust fender (figs. 4 and 5)

before tightening other screws. Always start adjustment

with original amount of shims, then add or remove shims

as required.

FENDER SKIRT

Removal

CAUTION: Chevelle air conditioned models

have condenser hoses routed through the right

front fender skirt. Cut skirt and bend as neces-

sary to move hoses clear of skirt. If necessary,

refer to Section 1A for air conditioning compo-

nents and procedures.

CHEVROLET CHASSIS SERVICE MANUAL

CHASSIS SHEET METAL 11-22

wiring harness, and washer bottle from radiator

support.

5.
Remove screw connecting battery tray to radiator

support.

6. Remove shroud from vehicle if so equipped.

7.
Remove shroud and radiator (Section 13).

8. Remove screws securing support to frame, skirts,

and fenders.

9. Remove radiator support from vehicle.

Installation

Install radiator support following the removal pro-

cedure in reverse order. Refer to torque specifications

in rear of manual for correct torque values for radiator

supportj grille, and bumper.

FENDER AND SKIRT ASSEMBLY

Removal

1.
Remove front bumper (Section 14).

2.
Remove hood and hood.hinges (two men).

3.
Remove bolts securing brace to skirt and dash panel

and remove brace (fig. 32).

4.
Disconnect any components attached to fender and

skirt such as cruise control, hoses, electrical har-

ness etc.

5.
Remove screws securing radiator support to fender

and skirt.

6. Remove headlamp bezel and headlamp.

7.
Remove screws securing fender and skirt assembly

to header panel, headlamp housing and valance panel.

Remove screw securing fender extension to valance

panel.

8. Remove screws securing fender and skirt assembly

to vehicle and remove fender and skirt assembly.

9. If necessary, remove screws attaching fender ex-

tension and bumper bracket to fender and remove

extension and bracket. Replace fender trim if nec-

essary.

Installation

Install fender anci skirt assembly following the removal

procedure in reverse order. Refer to torque specifi-

cations in rear of manual for correct torque values.

HOOD ASSEMBLY

Procedures for hood removal and installation for

Camaro are the same as for Chevrolet and Chevelle.

Refer to Chevrolet and Chevelle hood removal and in-

stallation procedures, Figure 35 for Camaro hood catch,

support, and lock plate, and Figure 37 for Camaro hood

and insulator.

HOOD CATCH AND LOCK (Fig. 35)

Removal

1.
Remove catch plate assembly by removing screws

retaining catch to header panel, center support, and

radiator support.

NOTE: Before removing hood lock plate from

hood, locate position on hood by scribing around

base of lock plate.

2.
Remove lock plate by removing screws retaining lock

plate to hood and remove lock plate.
Fig.
35 - Hood Catch, Support, and Lock Plate - Camaro

Installation

Install lock and catch plate following the removal pro-

cedure in reverse order. Refer to torque specifications

in rear of manual for correct torque values. Adjust lock

and catch plate as outlined under adjustment procedure

in this section.

HOOD TRIM AND INSULATION (Fig. 37}

. Figure 37 shows the installation details of the Camaro

hood ornament and insulation pad. The insulation and

ornament retainers and nuts are accessible from under

the raised hood.

COWL VENT GRILLE

.Procedures'for Camaro cowl vent grille replacement

are the same as for Chevrolet and Chevelle. Refer to

Chevrolet and Chevelle cowl vent grille replacement.

CHEVROLET CHASSIS SERVICE MANUAL