1967 CHEVROLET CAMARO instrument panel

ELECTRICAL-BODY AND CHASSIS 12-14

BACKING LAMPS

lamp Housing Replacement (Fig. 19)

Bumper Installation

1.
Remove two screws retaining housing assembly in

the bumper and remove housing.

'2.
Disconnect lamp wire assembly connector from wir-

ing harness.

3.
Remove lens retaining screws, lens and bulb from

housing assembly and transfer to new housing unit.

4.
Connect lamp wiring assembly to harness assembly,

housing and check operation of lamp.

•5.
Position lamp assembly in place and install retaining

screws.

Corvette (Fig. 18)

1.
Remove license plate and bracket assembly.

2.
Remove tailpipe extensions and rear body valance

panel.

3.
Remove backing lamp attaching nuts.

4.
Disengage backing lamp assembly from body opening

and disconnect wiring harness at rear of lamp.

5. Transfer bulb, gasket and lens to replacement

housing.

6. Connect chassis wiring connector to housing and po-

sition lamp assembly to body opening.

7. Attach ground wire to housing and install retaining

nuts to housing.

8. Install body valance panel.

9. Position license plate assembly to body and install

retaining screws.

LICENSE PLATE LAMP SERVICE

Lamp Housing

1.
Remove the lamp assembly retaining screws and re-

move lamp assembly from mounting location (rear

bumper center face bar most models). On Corvette

models remove rear valance panel.

2.
Disconnect lamp wiring from chassis harness con-

nector (inside trunk on some models).

3.
Force grommet and Wiring down through body open-

ing (where applicable) and remove assembly from

vehicle.

4.
To install replacement unit, insert grommet and wir-

ing through body opening where applicable and con-

nect wiring to chassis harness.

5. Position assembly and install retaining screws. On

Corvette models make sure ground wire is properly

installed.

6. Check operation of lamp assembly.

iuib Replacement

1.
Remove lens retaining screws and lens.

NOTE:
On Camaro models loosen housing re-

taining screws.

2.
Remove and replace bulb.

3.
Position lens and install retaining screws.
AUTOMATIC TRANSMISSION

QUADRANT LAMP REPLACEMENT

Chevrolet (Fig. 20)

1.
Remove four screws retaining lower mast jacket

cover to upper cover.

2.
Remove two screws retaining upper cover to instru-

ment console.

3.
Remove two screws securing shield to upper cover

assembly.

4.
Remove and replace bulb.

5. Position shield to upper cover assembly and install

retaining screws.

6.' Position upper cover assembly to instrument console

and install retaining screws.

7. Position lower cover and install four retaining

screws.

Chevy II and Camaro (Fig. 21)

1.
Remove two screws attaching retainer and dial to

directional signal housing; remove retainer and dial

face from housing.

2.
Remove cap and bulb.

3.
Replace bulb and cap, then position dial and retainer

to housing.and install attaching screws.

Fig.
20 - Dial Quadrant Lamp — Chevrolet

1.
Upper Cover

2.
Shield

3. Lamp and Socket
4.
Dial Pointer

5.
Lower Cover

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-15

Fig.
21 - Qlal Quadrant Assembly ~ Camaro

SEAT SEPARATOR CONSOLE LAMPS

COMPARTMENT LAMP REPLACEMENT (Fig.
22)

1.
Remove (pry up) switch assembly from console open-

ing in.the instrument compartment.

2.
Remove bulb from the socket.

3.
Replace bulb and install switch assembly in console

opening.

COURTESY LAMP REPLACEMENT (Fig. 22)

1.
Remove two screws and lens at rear of console.

2.
Remove bulb from retainer.

3.
Replace the bulb, position the lens and install attach-

ing screws.

QUADRANT LAMP REPLACEMENT (Fig. 22)

1.
Remove Dial Quadrant Trim plate retaining screws

and lift trim plate assembly from console opening.

2.
Disconnect lamp socket from the retainer and re-

move bulb from the socket.

3.
To install, insert bulb into the socket and snap the

socket assembly into the retainer.

Position the trim plate assembly into the console

opening and install the retaining screws.
4.

LIGHTING SWITCH REPLACEMENT (Fig. 24)

1.
Disconnect battery ground cable.

2.
Pull control knob out of headlamp ON position.

3.
Reach under instrument panel and depress the switch

shaft retainer (Fig. 25) and remove knob and shaft

assembly.

4.
Remove ferrule nut using Tool J-21932 and remove

switch assembly from instrument panel.

NOTE:
Some Chevelle models require use of

ToolJ-4880.

5. Disconnect the multi-plug connector from the lighting

switch. A screw driver may be inserted in the side
of the switch to pry the connector from the switch.

6. Connect the multi-plug connector to the replacement

switch (Fig. 23). Connect battery cable to battery

terminal and check operation of the light switch'in all

positions.

NOTE:
Ground switch- to check dome lamp

operation.

7. Position switch and bezel to panel mounting hole and

install ferrule jmt.

8. Insert switch control knob and shaft assembly into

switch until retainer engages shaft.

WIPER SWITCH REPLACEMENT (Fig. 26)

1.
Disconnect battery ground cable.

2.
Remove the connectors from the rear of the switch.

NOTE:
On Air Conditioned models it is nec-

essary to remove left A/C outlet duct for acces-

sibility to rear of switch.

3.
Loosen set screw and pull knob from switch shaft.

4.
Remove retaining nuts using special Tool J-21932

and withdraw wiper switch from behind console.

NOTE:
Some Chevelle models require special

ToolJ-4880.

5. To install, reverse removal procedure and check

operation of wipers.

STOPLIGHT SWITCH REPLACEMENT (Fig. 27)

1.
Disengage retaining fingers, disconnect wiring har-

ness connector from switch and unscrew switch from

mounting clip.

2.
Depress brake pedal and push new switch into clip

until shoulder bottoms out against clip.

3.
Check switch position for proper operation. Elec-

trical contact should be made when the brake pedal is

depressed 3/8" to 5/8" from fully released position.

DIMMER SWITCH REPLACEMENT (Fig. 28)

1.
Fold back upper left corner of front floor mat, disen-

gage connector lock fingers, and disconnect multi-

plug connector from dimmer switch.

2.
Remove two screws retaining dimmer switch to toe

pan.

3.
Connect multi-plug connector to new switch and

check operation. Install new switch to toe pan with

two screws. Replace floor mat.

BACKING LAMP SWITCH REPLACEMENT

Located on Mast Jacket (Fig. 29)

1.
Disconnect wiring connector at switch terminals.

2.
Remove switch attaching screws and switch from

mast jacket.

3.
Position new switch to mast jacket, install the re-

taining screws and connect wire connector to switch.

NOTE:
Position gear shift in neutral before

assembling switch to mast jacket.

4.
Check operation of switch.

Located on Transmission (Fig. 30)

1.
Raise and support vehicle.

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-19

VIEW A
•CONTACT SUPPORT

DRIVE SLOT IN LINE

WITH HOLE IN SWITCH

PAWL
CONTACT POINT B

CONTACT SUPPORT

DRIVE SLOT IN LINE

WITH HOLE IN SWITCH

FLOOR SHIFT

(EXCEPT CAMARO)
COLUMN SH

Fig.
31 - Neutral Safety Switches

PARKING BRAKE ALARM SWITCH REPLACEMENT

Corvette (Fig. 33)

1.
Remove seat belt retainer and parking brake cover

assembly from center console.

2.
Disconnect wire from brake alarm switch.

3.
Remove retaining screw and switch from

reinforcement.

4.
Position new switch to reinforcement and install re-

taining screw.

5. Connect switch wire and check operation of switch.

6. Install cover and seat belt retainer assembly.

Chevrolet, Chevelle, Chevy II and Camaro (Fig. 34)

1.
Disconnect wiring connector at switch terminal.

2.
Remove nut and lock washer or retaining bolt and

disengage switch from brace.

3.
To install, reverse removal procedure.

INSTRUMENT PANEL COMPARTMENT

LAMP/SWITCH REPLACEMENT

1.
Disconnect battery ground cable.

2.
Reach into glove box, depress bulb in end of switch
and turn counterclockwise to remove bulb.

3..
Remove switch from socket. Carefully detach wire

and terminal from switch.

NOTE:
On some model switches, the wire and

terminal cannot be detached from the switch

making it necessary to cut and splice the switch

wire.

4.
Insert wire and terminal into new switch.

5. Push switch into place and install bulb by setting it in

place, depressing and turning it clockwise.

CIGARETTE LIGHTER REPLACEMENT

Chevrolet, Chevy II, Camaro and Corvette (Fig. 23)

1.
Disconnect battery ground cable.

2.
Disconnect wire connector at rear of lighter unit

under dash.

3.
Remove retainer from rear of housing assembly and

disengage lighter unit from panel.

4.
To install, reverse removal procedure.

Chevelle (Fig. 35)

1.
Disconnect battery ground cable.

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-21

2.
Remove ash tray, retainer attaching screws and

retainer.

3.
Remove Air Conditioning distributor
duct'
retaining

screws and duct.

4.
Remove heater and/or Air Conditioning control panel

assembly retaining screws and push panel assembly

from console.

NOTE:
If interference between control panel

and radio is encountered, loosen radio retaining

nuts.

5. Remove radio control knobs, bezels and retaining

nuts.

6. Disconnect radio wiring harness and antenna lead-in.

7. Remove radio rear brace attaching screw and re-

move ra(Jio from vehicle.

8. Remove ignition switch bezel nut using Tool J-7607

and push switch rearward.

9. Disconnect cigarette wiring connector.

10.
Remove cigarette lighter retainer and lighter as-

sembly from console.

11.
To install, reverse removal procedure.
Fig.
35 - Cigarette Lighter — Chevelle

CHEVROLET INSTRUMENTS AND GAUGES

INDEX

Page

General Description 12-21

Service Operations 12-22

Instrument Cluster........................ 12-22

Instrument Cluster Lamps 12-22

Printed Circuit .
* •
12-22

Speedometer 12-22

Speedometer Cable 12-23

Fuel Gauge 12-23
Page

Clock 12-24

Tachometer 12-24

Ammeter . . 12-24

Temperature Gauge 12-24

Oil Pressure Gauge 12-24

Oil Pressure Indicator 12-24

Generator Indicator 12-26

Temperature Indicator 12-26

GENERAL DESCRIPTION

The standard instrument cluster on all models contains

seven circular housings consisting of: a speedometer;

fuel gauge; oil pressure, generator and temperature indi-

cators; right and left directional signal indicators; brake

warning and high beam indicators; and includes a clock

on deluxe models. An optionally available instrument

cluster provides special instrumentation which includes

in addition to the speedometer and clock: a tachometer;

fuel, oil pressure, ammeter and engine temperature

gauges; which replace the standard fuel gauge and indi-

cator lights. The brake warning indicator is relocated

to the tachometer dial face and the high beam and direc-

tional indicators are positioned in the speedometer dial

face.

Instrument cluster removal is recommended before at-

tempting to service the printed circuit and gauges even

though some units may be accessible from behind the

cluster. Limited working space under the instrument

panel increases the possibility of electrical malfunctions

due to poor connections, and damaged or improperly in-

stalled printed circuit. The printed circuit is service-

able but not repairable and requires complete
replacement.

The brake warning light serves a dual purpose. It

functions as an indicator when the parking brake is ap-

plied and also warns if a malfunction (loss of hydraulic

pressure) should occur in the brake system. The two

separate switches, which provide the signal to operate the

indicator, are located at the parking brake support and in

the hydraulic brake line at the master cylinder. Service

of the brake pressure, differential switch unit at the

master cylinder is described in Section 5 of this manual.

All indicator and cluster illumihating lamps may be

replaced without removing the cluster from the vehicle.

The bulbs are installed in plastic holders which lock into

the cluster housing and make contact with the printed

circuit. An instrument lamp is used to illuminate the

ignition switch. A special fibre optic lucite wiring

transmits light from the lamp to the switch.

Regular maintenance is not required on the instrument

cluster or its components other than maintaining clean,

tight electrical connections, replacing defective parts and

keeping the speedometer cable properly lubricated.

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-23

IGNITION SWITCH LIGHTING

VIEW A

1.
Clock Knob Assembly

2.
Instrument Cluster Lamps

3. R.H. Directional Indicator

4.
"Gen'*
Indicator

5. Fuel Gauge
Fig.
38 - Instrument Cluster Connections

6. L.H. Directional

Indicator

7. "Hot" indicator

8. "Brake" Indicator

9. "Bright" Indicator
10.
"Oil Press" Indicator

11.
Clock Cover (jl5,0OQ)

12.
Clock Assembly (16,000)

1.3; Printed Circuit

14.
Instrument Panel Connector

3.
Remove screws retaining speedometer to the housing

and remove speedometer from rear cover.

NOTE:
Servicing of the speedometer assembly

should be performed by an authorized
AC
Speed-

ometer Service Station.

4.
To install, reverse the removal procedure.

SPEEDOMETER CABLE

Replacement or Lubrication

1.
Disconnect the speedometer cable from the speedom-

eter head. Remove the old cable by pulling it out

from speedometer end of conduit.

NOTE:
If old cable is broken it may be neces-

sary to remove lower piece from transmission

end of conduit.
2.
Lubricate the lower 3/4 of cable with speedometer

cable lubricant and push the cable into the conduit.

Connect the upper end to the speedometer head and

road test vehicle for proper speedometer operation.

FUEL GAUGE REPLACEMENT

1.
Remove instrument cluster as previously described

in this section.

2.
Remove cluster lamps from gauge cover plate and

remove terminal nuts attaching circuit to gauge.

3.
Carefully move printed circuit away from gauge and

remove screws retaining gauge assembly to the

cluster housing.

4.
Remove gauge assembly from cluster housing and

remove three terminal nuts attaching gauge to the

cover plate.

CHEVROLET CHASSIS SERVICE MANUAL

10

27

18

1.
To R. H. Door Jamb Switch

2.
To Inst. Pane! Compt. Light

3. To Heater Control

4. Heater Control Lamp

5. To Ignition Switch

6. To Seat Separator Harness Conn.

7. Inst. Cluster Conn.

8. To Directional Signal Conn.

9.
Door Jamb Switch to Light Switch Conn,
Fig.
40 - Instrument Panel Wiring

10.
To Wiper Switch

11.
To Light Switch Conn.

12.
To Gen. and Fwd. LP. Harness Asm,

13.
To Light Switch

14.
Courtesy Lamp

15.
To Dome Lamp Conn.

16.
ToL.H. Door Jam Switch

17.
Gen. and Fwd Harness Conn.

18.
To Paricing Brake Alarm Switch
19.
To Rear Door Jamb Switch

20.
To Fisher Body Conn.

21.
To Stop Lamp Switch

22.
To Back-Up Lamp Switch

23.
To Directional Signal Flasher

24.
To Cigarette Lighter

25.
To Heater Resistor

26.
Directional Signal Flasher

27.
Door Jamb Switch

ELECTRICAL-BODY
AND
CHASSIS
12-26

•
Low oil
pressure

• High engine temperature

• Defective wiring
or
switch

connector from sender

in block above starter
on

and
at
left front
of
distributor
on V-8
Sending Unit Replacement

1.
Disconnect wiring harness

unit terminal (located

L-6 engines

engines).

2.
Remove sender unit using Tool J-21757
or 12
point

socket, replace with
new
unit
and
check operation.

GENERATOR INDICATOR

1.
Ignition
on,
Engine
not
Running
and
Telltale Light

Off.

• Indicator bulb burned out, replace bulb.

• Open circuit
or
loose connection
in the
telltale

light circuit.

2.
telltale Light Stays
on
after Engine
is
Started.
If indicator light does
not go out at
engine idle

speed, refer
to
Charging Systems under Engine

Electrical, Section
6Y.

TEMPERATURE (COOLING SYSTEM) INDICATOR

The temperature indicator circuit consists
of two re-

motely located units, indicator gauge
and
engine sender

unit.
The
indicator gauge, located
in the
instrument

panel, consists
of a
red light which will indicate
an
over-

heated engine condition.

Engine Sender Unit Replacement

1.
Drain engine cooling system
to a
level below unit.

2.
Remove sender unit (located
in the
inlet manifold

near water pump housing
on V-8
engines and
in the

cylinder head near
an
exhaust port
oh L-6
engines)

and replace with new unit.

3.
Refill cooling system
and
check operation
of
unit.

CHEVELLE INSTRUMENTS AND GAUGES

INDEX

Page

General Description
* *
i2-26

Service Operations
12-26

Instrument Panel
12-26

Instrument Cluster.
12-26

Fuel Gauge and/or Ammeter
12-27

Clock,
i 12-27

Speedometer
12-27
Page

Speedometer Cable
.
. 12-27

Temperature Gauge
12-29

Oil Pressure Gauge
12-29

Indicator Lights.
. 12-29

Oil Pressure Indicator
12-29

Generator Indicator
. . 12-29

• Temperature Indicator
12-29

GENERAL DESCRIPTION

The Chevelle instrument cluster assembly consists
of:

a speedometer;
a
fuel gauge;
a
generator,
an
engine
tem-

perature and an
oil
pressure indicator lamp, and includes

a clock
on
deluxe models.
On
super sport models,
am-

meter, coolant temperature
and oil
pressure gauges
re-

place
the
appropriate indicator lights. Except
for the

speedometer,
all of the
indicator lamps, instruments
and

gauges
of
these clusters may
be
serviced without remov-

ing
the
instrument cluster assembly from
the
vehicle.

In addition
to the
instrument indicator lamps,
a
brake

warning lamp
is
included
in the
cluster
as
standard

equipment.
The
indicator
is
connected
to the
parking
brake
and
brake pressure differential switches
and

serves
a
dual function.
It
lights when the parking brake

is applied
and
also when
the
brake pedal
is
applied,
if a

malfunction should occur
in the
brake system
due to a

loss
of
hydraulic pressure. Servicing
of the
hydraulic

pressure differential switch
is
covered
in
Section
5 of

this manual.

Regular maintenance
is not
required on the instrument

cjLuster
or its
components other than maintaining dean

and tight electrical connections, replacing defective parts

and keeping
the
speedometer cable properly lubricated.

SERVICE OPERATIONS

INSTRUMENT PANEL ASSEMBLY

INSTRUMENT CLUSTER (Figs.
41
thru
44)

Removal

1.
Disconnect battery ground cable.

2.
Remove steering coupling bolt and disconnect steer-

ing shaft from coupling.

3.
Loosen mast jacket lower clamp.

4.
Remove
air
conditioning center distributor duct
(if

so equipped).

5. Remove radio rear support bracket screw.

6. Remove mast jacket upper support clamp and retain-

ing bolts from lower support (refer
to
Section
9,

Steering).
CAUTION: Cover mast jacket
and
parl

brake handle with
a
suitable material
to
prevc

scratching.

7.
Disconnect speedometer cable
at
rear
of
cluster

housing
and
speed warning control knob
at
panel
(if

so equipped).

8. Remove instrument panel retaining screws (nine

upper and five lower).
.

9. Working under the console remove four lower retain-

ing screws from instrument cluster housing.

10.
Pull instrument panel assembly from console and
lay

forward on mast jacket.

11.
Disconnect wiring harness, cluster lamps and wiring

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-27

Fig.
41 - Instrument Panel Installation — Chevelle

terminals from rear of cluster assembly (figs. 43

and 44).

12.
Remove four screws retaining upper section of dus-

ter housing to panel and remove cluster from the in-

strument panel and to a suitable working area for

necessary service (fig. 42).

Installation

1.
Position cluster assembly to rear of panel and install

four upper retaining screws.

2.
Connect cluster lamps, wiring connectors and wiring

harness assembly to the cluster assembly.

3.
Position instrument panel assembly into console

(hold panel at center and install center screws) and

install upper and lower retaining screws.

NOTE:
At this point temporarily reconnect

battery and check operation of cluster.

4.
Working under the console, install four lower screws

retaining lower section of cluster cover to rear of

panel.

5. Install radio brace screw at rear of radio.

6. Connect speedometer cable to speedometer and speed

warning device control knob.

7. Install A/C distributor duct and connect A/C hoses to

duct (if so equipped).

8. Install mast jacket upper support clamp.

9. Position steering shaft in the steering coupling and

install retaining bolt.

10.
Tighten mast jacket lower clamp (refer to Steering,

Section 9 for spring tension adjustment).

11.
Connect battery ground cable.

FUEL GAUGE AND/OR AMMETER

REPLACEMENT

1.
Disconnect battery ground cable.

2.
On air conditioned models, disconnect hose and re-

move air outlet from panel.

3.
Disconnect wiring connectors and cluster lamps from

rear of gauge assembly.

4.
Remove mounting plate retaining screws (3) and re-
move fuel gauge from rear of cluster housing.

5. Remove terminal nuts (3) securing gauge to template

and replace gauge.

6. To install, reverse the removal procedure.

CLOCK REPLACEMENT

1.
Disconnect battery ground cable.

2.
Remove clock set shaft knob retaining nut and knob.

3.
Disconnect wiring connector at clock terminal and

cluster lamp from clock housing. On A/C models,

disconnect hose from air distributor duct.

4.
Remove two screws retaining clock housing to

cluster cover and remove clock.

5. To install, reverse removal procedure.

SPEEDOMETER REPLACEMENT

1.
Disconnect battery ground cable.

2.
Remove instrument cluster assembly as previously

outlined in this section.

3.
Remove screws (8) attaching cover to rear of cluster

housing.

4.
Remove two screws attaching speedometer assembly

to cluster cover and carefully remove speedometer

head.

NOTE:
Servicing of the speedometer assembly

should be performed by an authorized
AC
speed-

ometer service station.

5. To install, reverse removal procedure.

SPEEDOMETER CABLE

Replacement or Lubrication

1.
Disconnect the speedometer cable from the speedom-

eter head. Remove the old cable by pulling it out

from speedometer
, end
of conduit.

NOTE:
If old cable is broken it may be neces-

sary to remove lower piece from transmission

end of conduit.

2.
Lubricate the lower 3/4 of cable with speedometer

cable lubricant and push the cable into the conduit.

Connect the upper end to the speedometer head and

road test vehicle for proper speedometer operation.

Fig.
42 - Instrument Cluster Installation

CHEVROLET CHASSIS SEtVKE MANUAL