1967 CHEVROLET CAMARO weight

ENGINE 6-20

Fig.
11 L
- J-21742 Centering Tool in Cover

tion from walking off the hub during installation

of damper.

2.

3.
Attach damper installer Tool J-22197 to damper.

Tighten fingers of tool to prevent weight from moving

(fig. 10L).

Position damper on crankshaft and drive into posi-

tion, using J-5590, until it bottoms against crankshaft

gear (fig. 10L). Remove installer tool.

4.
Install fan belt and adjust using strand tension gauge.

5.
If so equipped, install accessory drive pulley and

belt.

6. Install radiator core as outlined in Section 13.

7.
Fill cooling system and check for leaks.

CRANKCASE FRONT COVER

Fig.
121
- Installing Oil Seal (Cover Removed)
Fig. 13L- Installing Oil Seal (Cover installed)

Removal

1.
Remove oil pan as outlined.

2.
Remove crankshaft pulley and hub or torsional

damper as outlined.

3.
Remove crankcase front coyer attaching bolts, re-

move cover and gasket.

Installation

1.
Clean gasket surfaces on block and crankcase front

cover.

2.
Install centering Tool J-996 or Tool J-21742 in

crankcase front cover seal (fig. 11L).

3.
Coat the gasket with gasket sealer and place in posi-

tion on cover, then install crankcase front cover to

block and torque bolts to specifications.

4.
Remove centering tool.

NOTE: It is important that centering tool be

used to align crankcase front cover so that

crankshaft hub or torsional damper installation

will not damage seal and to position seal evenly

around the balancer or hub surface.

5.
Install crankshaft hub and/or torsional damper as

outlined.

6. Install oil pan with new gaskets and seals as outlined.

OIL SEAL (FRONT COVER)

Replacement

With Cover Removal

1.
With cover removed, pry old seal out of cover from

the front with screw driver being careful not to

distort cover.

2.
Install new seal so that open end of the seal is toward

the inside of cover and drive it into position with

ToolJ-995 (fig. 12L).

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE 6-23

ENGINE MOUNTS

Engine mounts (fig. 21L) are the non-adjustable type

and seldom require service. Broken or deteriorated

mounts should be replaced immediately, because of the

added strain placed on other mounts and drive line

components.

Front Mount Replacement

Chevrolet,
Chevelle, and Comoro

1.
Remove nut, washer, spacer then engine mount

through-bolt.

2.
Raise engine to release weight from mount.

3.
Remove mount, stop bracket and frame bracket as-

sembly from crossmember, then remove stop

bracket and mount from frame bracket.

4.
Install stop bracket and new mount on frame bracket,

then install assembly on crossmember.

5.
Lower engine, install through-bolt and tighten all

mount bolts to specified torques.

Chevy II

, 1. Remove nut, washer and engine mount through-bolt.

2.
Raise engine to release weight from mount.

3.
Remove bracket-to-mount bolt, then remove mount.

4.
Install new mount on bracket.

5.
Lower engine, install through-bolt and tighten all

mount bolts to specified torques.

Rear Mount Replacement
Chevrolet

1.
Remove crossmember-to-mount bolts.

2.
Raise transmission to release weight from mount.

3.
Remove mount-to-trans mission bolts, then remove

mount and spacer.

4.
Install spacer and new mount on transmission.

5.
While lowering transmission, align and start cross-

member-to-mount bolts.

6. tower transmission and tighten all mounting bolts

to specified torques.

Chevelle and Camaro

1.
Remove crossmember-to-mount bolts.

2.
Raise transmission to release weight from mount.

3.
Remove mount-to-transmission bolts, then remove

mount.

4.
Install new mount on transmission.

5.
While lowering transmission align and start cross-

member-to-mount bolts.

6. Lower transmission and tighten all mounting bolts to

specified torques.

Chevy II

1.
Remove crossmember-to-mount bolts.

2.
Raise transmission to release weight from mount.

3.
Remove mount-to-transmission bolts, then remove

mount.

4.
Install new mount on transmission.

5.
While lowering transmission align and start cross-

member-to-mount bolts.

6. Lower transmission and tighten all mounting bolts

to specified torques.

FRONT

CHEVROLET

REAR

REAR
L4 FRONT

CHEVY II

L6 FRONT

L6 REAR
FRONT

CAMARO

REAR

Fig.
21L- Engine Mounts

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE 6-25

refer to Section 6 of the Chassis Overhaul Manual.

Because of the interchangeability and similarity of

many engines, engine sub-assemblies and engine parts,

regardless of which passenger vehicle they are used in,

typical illustrations and procedures are used except
where specific illustrations or procedures are necessary

to clarify the operation. Although illustrations showing

bench operations are used, most single operations, when

not part of a general overhaul, should be performed (if

practical) with the engine in the vehicle.

COMPONENT REPLACEMENT AND ADJUSTMENT

ENGINE ASSEMBLY

Removal

• .1. Drain cooling system and engine oil.

2.
Remove air cleaner and disconnect battery cables at

battery.

3.
Remove hood as outlined in Section 11.

4.
Remove radiator and shroud as outlined in Sec-

tion 13.

5. Remove fan blade and pulley as outlined in Sec-

tion 6K.

6. Disconnect wires at:

• Starter solenoid

• Delcotron

• Temperature switch

• Oil pressure switch

• Coil

7. Disconnect:

• Accelerator linkage at pedal lever.

• Exhaust pipes at manifold flanges.

• Vacuum line to power brake unit at manifold (if

so equipped),

• Power steering pump lines at pump end (if so

equipped).

• Fuel line (from tank) at fuel pump.

• Engine cooler lines (if so equipped).

• Oil pressure gauge line (if so equipped).

8. Raise vehicle and place on jack stands.

9. Remove propeller shaft.

NOTE:
If plug for propeller shaft opening

in transmission is not available, drain

transmission.

10.
Disconnect:

• Shift linkage at transmission.

• Speedometer cable at transmission.

• Transmission cooler lines (if so equipped).

11.
On synchromesh equipped vehicles, disconnect clutch

linkage at cross-shaft then remove cross-shaft en-

gine bracket.

12.
Remove rocker arm covers as outlined, then attach

engine lifting adapter at the proper cylinder head bolt

locations.

13.
Remove front mount bolts.

14.
Attach lifting device and raise engine to take weight

off front mounts, then remove rear mount bolts.

15.
Raise engine to take weight off rear mount, then re-

move crossmember.

NOTE:
On Chevrolets it will be necessary to

remove mount from transmission before cross-

member can be removed.

16.
Remove engine-transmission assembly from vehicle

as a unit.

17.
Remove transmission (and clutch):
Synchromesh Transmission

a. Remove clutch housing cover plate screws.

b.
Remove bolts attaching the clutch housing to en-

gine block then remove transmission and clutch

housing as a unit.

NOTE:
Support the transmission as the last

mounting bolt is removed, and as it is being

pulled away from the engine (to prevent damage

to clutch disc).

c. Remove starter and clutch housing rear cover

plate.

d. Loosen clutch mounting bolts a turn at a time (to

prevent distortion of clutch cover) until the spring

pressure is released. Remove all bolts, clutch

disc and pressure plate assembly.

Automatic
Transmission

a. Lower engine, secured by the hoist, and support

engine on blocks.

b.
Remove starter and converter housing underpan.

c. Remove flywheel-to-converter attaching bolts.

d. Support transmission on blocks.

e. Remove transmission-to-engine mounting bolts.

f. With the hoist attached, remove blocks from the

engine only and slowly guide the engine from the

transmission.

18.
Mount engine in stand.

Installation

1.
Attach lifting device to engine and remove engine

from engine stand.

2.
Install transmission (and clutch):

Synchromesh Transmission

a. Install the clutch on flywheel as outlined in Sec-

tion 7.

b.
Install clutch housing rear cover and starter.

c. Install transmission and clutch housing as out-

lined in Section 7.

d. Install clutch housing cover screws and tighten

securely.

Automatic
Transmissions

a. Position engine adjacent to the transmission and

align the converter with the flywheel.

b.
Bolt transmission to engine, then raise engine and

transmission assembly and install flywheel to

converter attaching bolts.

c. Install converter housing underpan and starter.

3.
Tilt and lower engine and transmission assembly into

the chassis as a unit, guiding engine to align front

mounts with frame supports.

4.
Install front mount bolts and torque to specifications.

5. Raise engine enough to install rear crossmember,

then install crossmember, install rear mount, lower

engine and torque rear mount to specifications.

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE 6-30

c". Install the valve locks and release the compres-

sor tool making sure the locks seat properly in

the upper groove of the valve stem.

NOTE: Grease may be used to hold the locks

in place while releasing the compressor tool.

396 and 427
cu.
in.
Engines

a. Install new valve stem oil seal (coated with oil)

in position over valve guide.

b.
Set the valve spring and damper and valve cap in

place.

c. Compress the spring with Tool J-5892 and install

the valve locks, then release the compressor tool,

making sure the locks seat properly in the groove

of the valve stem.

NOTE: Grease may be used to hold the locks

in place while releasing the compressor tool.

7.
Install spark ,plug, using a new gasket, and torque to

specifications. -

8. Install and adjust valve mechanism as outlined.

CYLINDER HEAD ASSEMBLY

Removal

1.
Remove intake manifold as outlined.

2.
Remove exhaust manifolds as outlined.

3.
Remove valve mechanism as outlined.

4.
Drain cooling system (block).

5.
Remove cylinder head bolts, cylinder head and gas-

ket. Place cylinder head on two blocks of wood to

prevent damage.

Installation

CAUTION: The gasket surfaces on both the

head and the block must be clean of any foreign

ttter and free of nicks or heavy scratches.

Under bolt threads in the block and threads on

Pie cylinder head bolt must be cleaned. (Dirt

will affect bolt torqueT)

1.
On engines using a STEEL gasket, coat both sides of

a new gasket with a good sealer, spread the sealer

thin and even. One method of applying the sealer that

will assure the proper- coat is with the use of a paint

roller. Too much sealer may hold the beads of the

gasket away from the head or block.

CAUTION: Use no sealer on engines using a

composition STEEL ASBESTOS gasket.

2.
Place the gasket in position over the dowel pins with

the bead up.

3.
Carefully guide cylinder head into place over dowel

pins and gasket.

4.
Coat threads of cylinder head bolts with sealing

compound and install finger tight.

5.
Tighten cylinder head bolts a little at a time in the

sequence shown on the torque sequence chart until

the specified torque is reached.

6. Install the exhaust manifold as outlined.

7.
Install the intake manifold as outlined.

8. Install and adjust the valve mechanism as outlined.
OIL
PAN

Removal

Chevrolet
and Camaro

1.
Disconnect battery positive cable.

2.
Disconnect distributor cap from distributor (to pr-e-

vent breaking distributor cap when engine is raised).

3.
Drain radiator, then disconnect lower radiator hose

at water pump and remove oil dip stick and tube

(where necessary). '

4.
Remove fan blade.

5.
Raise vehicle then drain engine oil;

6. Remove through bolts from engine front mounts.

Disconnect and remove starter.

7.
On vehicles equipped with automatic transmissions,

remove converter housing underpan.

8. Disconnect steering rod at idler lever then swing

steering linkage 4pwn for oil pan clearance.

9. Rotate crankshaft untii timing mark on torsional

damper is at 6:00 o'clock position.

10.
Using a suitable jack, and a block of wood to prevent

damaging oil pan, raise engine "enough to insert 2" x

4"
wood blocks under engine mounts (fig. 8V), then

lower engine onto blocks.

NOTE: If 2" x 4" wood blocks are cut 5-1/2"

long they can be used on all Chevrolet engines.

The 5-1/2" length up for In-line engines and the

4"
side up for V8 engines.

11.
Remove oil pan and discard gaskets and seals.

NOTE: -On the 396 and 427 cu. in. engine, the

oil pan has three 1/4" x 20 attaching bolts at ,

crankcase front cover. One located at each

corner and one at lower center.

Chevelle

1.
Remove engine from vehicle as outlined.

2.
Lower engine onto jack stands, one at each front

Tnaount and one at transmission extension.

CAUTION: Leave engine lift attached to en-

gine.
Do not remove all weight of engine off

engine lifET

3.
Remove starter.

4.
On vehicles equipped with automatic transmission

remove converter housing underpan.

5.
Remove oil pan and discard gaskets and seals.

Fig.
8V - Engine Blocked for Pan Removal

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE 6-33

Fig.
13V - Installing TorsionaI Damper (283, 327 and 350)

4.
Remove accessory drive pulley, then remove tor-

sional damper retaining bolt (if so equipped).

5. Install Tool J-6978 to torsional damper and turn

puller screw to remove damper from crankshaft

(fig. 12V).

6. Remove tool.

Installation

CAUTION: It is necessary to use installer tool

to prevent the inertia weight section from walk-

ing off the hub during installation of damper.

283, 327 and 350 cu. in. Engines

(Except 327-325 HP & 350 HP)

1.
Coat front cover seal contact area (on torsional

damper) with engine oil.

Fig.
14V - Installing Torsional Damper (396 and 427)
2.
Attach damper installer Tool J-22197 to damper.

Tighten fingers of tool to prevent weight from moving

(fig. 13V).

3.
Position damper on crankshaft and drive into position

until it bottoms against crankshaft sprocket (fig.

13V).
Remove installer tool.

4.
Install accessory drive pulley.

5. Install radiator and shroud as outlined in Section 13.

6. Install fan pulley and fan as outlined in Section 6K.

7. Install fan belt and adjust to specifications using

strand tension gauge.

8. Fill cooling system, start engine and check for leaks.

396 and 427
cu.
in.
Engines

1.
Coat front cover seal contact area (on damper) with

engine oil.

2.
Place damper in position over key on crankshaft.

3.
Using Tool J-21058 pull damper onto crankshaft

(fig. 14V).

NOTE:
If engine or radiator has not been re-

moved from the vehicle a 1/2"- 20 x 5" bolt and

a
1/2"-20
nut may be used in place of the bolt

and nut of Tool J-21058.

CAUTION: Install bolt in crankshaft with suffi-

cient thread engagement (min. 1/2").

4.
Remove tool from crankshaft.

5. Install damper retaining bolt and torque to specifica-

tions,
then install accessory drive pulley.

6. Install radiator and shroud as outlined in Section 13.

7. Install fan pulley and fan as outlined in Section 6K.

8. Install fan belt and adjust to specifications using

strand tension gauge.

9. On Corvettes, lower engine and install front mount

through-bolts.

10.
Fill cooling system, start engine and check for leaks.

327
cu.
in. (325 & 350 HP)
Engine

Install damper as outlined for 396 and 427 cu. in. en-

gines,
using a 7/16"-20 x 5" bolt and nut in place of the

bolt and nut furnished with J-21058.

CRANKCASE FRONT COVER

Removal

1.
Remove oil pan as outlined.

2.
Remove torsional damper as outlined.

3.
Remove water pump as outlined in Section 6K.

4.
Remove crankcase front cover attaching bolts and

remove front cover and gasket, then discard gasket

Installation

283, 327 and 350 cu. in.
Engine

1.
Make certain that cover mounting face and cylinder

block front face are clean and flat.

2.
Coat the oil seal with engine oil and using a new

cover gasket, coated with gasket sealer, install cover

and gasket over dowel pins and cylinder block.

3.
Install cover screws and torque bolts to

specifications.

4.
Install water pump as outlined in Section 6K.

5. Install torsional damper as outlined.

6. Install oil pan as outlined.

CHEVROLET CHASSIS SOVKZ MANUAL

ENGINE 6-37

Fig.
27V—Removing Camshaft

4.
Set dial indicator on zero, then rotate the damper

slowly, or attach an auxiliary starter switch and

"bump" the engine over, until the push rod is in the

fully raised position.

CAUTION: The primary distributor lead must

be disconnected from the negative post on the

coil and the ignition switch must be in the on

position. Failure to do this will result in a dam-

aged grounding circuit in the ignition switch.

5.
Compare the total lift recorded from the dial indica-

tor with specifications.

6. Continue to rotate the crankshaft until the indicator

reads zero. This will be a check on the accuracy of

the original indicator reading.

7.
If camshaft readings for all lobes are within specifi-

cations, remove dial indicator assembly.

8. Install and adjust valve mechanism as outlined.

Removal

1.
Remove valve lifters as outlined.

2.
Remove crankshaft front cover as outlined.

3.
Remove grille as outlined in Section 13.

4.
Remove fuel pump push rod as outlined * in Sec-

tion 6M.

5.
Complete camshaft removal as follows:

CAUTION: All camshaft journals are the same

diameter and care must be used in removing

camshaft to avoid damage to bearings.

Remove camshaft sprocket to camshaft bolts then

remove sprocket and timing chain together. Sprocket

is a light fit on camshaft. If sprocket does not come

off easily a light blow on the lower edge of the

sprocket (with a plastic mallet) should dislodge the

sprocket.

Install two 5/16" - 18 x 4" bolts in camshaft bolt

holes then remove camshaft (fig. 27V).

Installation

NOTE: Whenever a new camshaft is installed
CONVERTER

BOLT AREA -

DEPRESSED

SYNCHROMESH
RING

GEAR

TRANS.,

AUTOMATIC

Fig.
28V - Flywheel Installation (Typical)

coat camshaft lobes with Molykote or its

equivalent.

1.
Lubricate camshaft journals with engine oil and in-

stall camshaft.

2.
Install timing chain on camshaft sprocket. Hold the

sprocket vertical with the chain hanging down, and

orient to align marks on camshaft and crankshaft

sprockets. Refer to Figure 20V.

3.
Align dowel in camshaft with dowel in hole in cam-

shaft sprocket then install sprocket on camshaft.

Refer to Figure 25V.

4.
Draw the camshaft sprocket onto camshaft using the

mounting bolts. Torque to specifications.

5.
Lubricate timing chain with engine oil.

6. Install fuel pump push rod as outlined in Section 6M.

7.
Install grille as outlined in Section 13.

8. Install crankcase front cover as outlined.

9. Install valve lifters as outlined.

FLYWHEEL

Removal

With transmission and/or clutch housing and clutch

removed from engine, remove the flywheel.

Installation

1.
Clean the mating surfaces of flywheel and crankshaft

to make certain there are no burrs.

2.
Install flywheel on crankshaft and position to align

dowel hole of crankshaft flange and flywheel (fig.

28V).

NOTE: On Automatic Transmission equipped

engines, the flywheel must be installed with the

flange collar to transmission side (fig. 33V).

ENGINE MOUNTS

Engine mounts (fig. 34V) are the nonr adjustable type

and seldom require service. Broken or deteriorated

mounts should be replaced immediately, because of the

added strain placed on other mounts and drive line

components.

Front Mount Replacement

1.
Remove nut, washer and engine mount through-bolt.

2.
Raise engine to release weight from mount.

3.
Remove mount from engine.

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE
6-38

4.
Install new mount on engine.

5. Lower engine, install through-bolt and tighten all

mount bolts to specified torques.

Rear Mount Replacement

1.
Remove crossmember-to-mount bolts.

2.
Raise transmission to release weight from mount.
3.
Remove mount-to-transmission bolts, then remove

mount (and spacer on Chevrolets).

4.
Install new mount (and spacer on Chevrolets) on

transmission.

5. While lowering transmission, align and start cross-

member-to-mount bolts.

6. Lower transmission and tighten all mounting bolts

to specified torques.

CHEVELLE
CHEVY
II

FRONT

REAR
CORVETTE

FRONT

REAR
CAMARO

FRONT

REAR

Fig.
29V -
Engine Mounts

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE-ELECTRICAL 6Y-18

IGNITION SYSTEMS

INDEX

Page

General Description . 6Y-18

Maintenance and Adjustments 6Y-19

Breaker Point System 6Y-19

Breakerless System . . 6Y-X9

Ignition Coil Check 6Y-19

Spark Plugs 6Y-19

Service Operations , 6Y-19

Distributor Contact Points . 6Y-19

Cleaning 6Y-19

Replacement 6Y-20

Setting Dwell Angle 6Y-21

Distributor Condenser 6Y-22

Performance Diagnosis. 6Y-22

Replacement . . 6Y-23

Distributor

Breaker Point Type 6Y-23

Removal. . 6Y-23

Disassembly • 6Y-23
Page

Cleaning and Inspection .....'.., 6Y-25

Assembly . 6Y-25

Installation 6Y-26

Breakerless i 6Y-27

Removal . 6Y-27

Disassembly and Assembly 6Y-27

Installation 6Y-27

Off-Engine Test. . 6Y-27

Coil Replacement 6Y-27

Pulse Amplifier. 6Y-28

Disassembly .6Y-4S8

Component Checks
!
6Y-28

Assembly 6Y-29

Ignition Switch Replacement 6Y-29

Spark Plugs 6Y-30

Cleaning and Regapping I ....... 6Y-30

Installation . 6Y-31

GENERAL DESCRIPTION

There are two ignition systems available on 1967

vehicles. The breaker point type which is continued as

the regular production system and the optional (Corvette

only) transistor controlled breakerless ignition system

(magnetic pulse type). The transistor ignition system

features a specially designed distributor, control unit

(ignition pulse amplifier), and a special coil. Two resist-

ance wires are also used in the circuit; one as a ballast

between the coil negative terminal and ground, while the

other resistance wire provides a voltage drop for the

engine run circuit and is by-passed at cranking. The

other units in the system (the ignition switch, spark

plugs,
and battery) are of standard design. The dis-

tributor and control unit (ignition pulse amplifier) are

shown in Figures li and 2i.

CAP-

VACUUM

PICK-UP

COIL LEADS

PICK-UP COIL

CONNECTOR BODY
Although the external appearance of the distributor

resembles a standard distributor, the internal construc-

tion is quite different. As shown in the exploded view

(fig. 16i) an iron timer core replaces the conventional

breaker cam. The timer core has the same number of

equally-spaced projections, or vanes as engine cylinders.

The timer core rotates inside a magnetic pickup as-

sembly, which replaces the conventional breaker plate,

contact point set, and condenser assembly. The magnetic

pickup assembly consists of a ceramic permanent mag-

net, a pole piece, and a pickup coil. The pole piece
is.
a

steel plate having equally spaced internal teeth, one tooth

for each cylinder of the engine.

The magnetic pickup assembly is mounted over the

main bearing of the distributor housing, and is made to

rotate by the vacuum control unit, thus providing vacuum

advance. The timer core is made to rotate about the shaft

by conventional advance weights, thus providing centrifu-

gal advance.

Fig.
li—
Magnetic Pulse Distributor
Fig.
2i-lgnition Pulse Amplifier Unit

CHEVROLET CHASSIS SERVICE MANUAL