1967 CHEVROLET CAMARO turn

FRONT SUSPENSION 3-5

FRONT END ALIGNMENT

Front end alignment, that is alignment of the inter-

related steering components of the front suspension sys-

tem, must be correctly maintained to assure ease and

stability of steering and satisfactory tire life.

Alignment Preliminary Steps

Several different types of machines are available for

checking all the factors of front end alignment. The in-

structions furnished with each particular machine should

be followed. In all cases, however, checks should be

made with the vehicle level and at curb weight.

Since steering complaints are not always the result of

improper alignment a check should be made to see if any

of the following conditions exist. Any such conditions

should be corrected before proceeding further.

1.
Steering gear loose or improperly adjusted.

2.
Steering gear housing loose at frame.

3.
Excessive wear or play in spherical joints or steer-

ing shaft coupling.

4.
Tie rod or steering connections loose.

5.
Improper front spring heights.

6. Unbalanced or underinflated tires.

7.
Improperly adjusted wheel bearings.

8. Shock absorbers not operating properly.

Wheel alignment should always be made with the vehi-

cle rolled forward taking out any slack in the same man-

ner as when the vehicle is traveling forward.

Caster and Camber Adjustment

NOTE: Before adjusting caster and camber

angles, the front bumper should be raised and

quickly released to allow car to return to its

normal height.

Chevelle, Camaro and Corvette

Caster and camber adjustments are made by means of

shims inserted between the upper control arm inner sup-

port shaft and the support bracket attached to the frame

(fig. 6). Shims may be added, subtracted or transferred

to change the readings as follows:
Fig.
6 - Caster and Camber Adjustment - Chevelle

Typical of Corvette and Camaro

Caster - change shims at either the front or rear of

the shaft.

The addition of shims at the front bolt or removal

of shims at the rear bolt will decrease positive

caster. One shim (1/3 2") will change caster (ap-

prox.) 1/4°.

Camber - change shims at both the front and rear of

the shaft.

Adding an equal number of shims at both front and

rear of the support shaft will decrease positive cam-

ber. One shim (1/32") at each location will move

camber (approx.) 1/5° (Chevelle and Camaro); 1/6°

(Corvette).

TIGHTEN TO LOCK

ADJUSTMENT

Fig.
7 - Caster and Camber Adjustment Points - Chevrolet

CHEVROLET CHASSIS SERVICE MANUAL

FRONT SUSPENSION 3-6

Fig.
8 - Caster and Camber Adjustments - Chevy

To adjust for caster and camber, loosen the upper sup-

port shaft to crossmember nuts, add or subtract shims as

required and retighten nuts.

NOTE:
Caster and camber can be adjusted in

one operation.

Caster and camber specifications will be found in the

last section of this book.

Chevrolet and Chevy II

The caster angle is adjusted by turning the two niits at

the front of the lower control arm strut rod (figs. 7 and

8).
Shortening this rod will increase caster. Lengthen-

ing will decrease caster.

Camber angle is adjusted by loosening the lower con-

trol arm pivot bolt and rotating the cam located on this

pivot. This eccentric cam action will move lower control

arm in or out, thereby varying camber.

Steering Axis Inclination Adjustment

"Camber" is the outward tilt of the wheel and "steering

axis inclination" is the inward tilt of the knuckle. Cam-

ber cannot be changed without changing steering axis

inclination. Correct specifications willbe found at the

end of this section. If, with the camber correctly ad-

justed, the steering axis inclination does not fall within

the specified limits the knuckle is bent and should be

replaced.

If a new knuckle is installed, caster, camber and toe-in

must be readjusted.

Toe-In Adjustment

Toe-in, the inward pointing of both front wheels, is

checked with the wheels in the straight ahead position. It

is the difference of the distance measured between the

extreme front and the distance measured between the ex-

treme rear of both front wheels. Correct toe-in specifi-

cations will be found at the end of this section.
NOTE:
Toe-in must be adjusted after caster

and camber adjustment.

A. If the equipment being used measures the toe-in of

each wheel individually:

1.
Set the steering gear on the high point, mark 12

o'clock position on the steering shaft and position

the steering wheel for straight ahead driving.

2.
Loosen the clamp bolt at each end of each tie rod

and adjust to the total toe-in as given in the speci-

fications at the end of this book.

B.
If a tram gauge is being used, proceed as follows:

1.
Set the front wheels in the straight ahead position.

2.
Loosen the clamp bolts on one tie rod and adjust

for the proper toe-in as given in the specifications

at the end of this book.

3.
Loosen the clamp bolts on the other tie rod. Turn

both rods the same amount and in the same direc-

tion to place the steering gear on its high point and

position the steering wheel in its straight ahead

position.

C.
After the adjustment has been made:

1.
a. Chevrolet—Position inner tie rod clamp bosses

forward to 90° down to avoid stabilizer link bolt

interference.

b.
Chevelle—Position the tie rod clamp bosses

down to 45?° forward to avoid interference.

c. Chevy II--Position the outer tie rod clamp

bosses forward and not more than 45° up or

down from horizontal to avoid interference.

Inner clamps forward and vertical.

d. Corvette--Position inner tie rod clamps with

bolt horizontal and down. Position outer clamps

with bolt vertical and to the rear.

e. Camaro—Position inner tie rod clamps with

open end of clamp and slot in line. Position

relative to ground unimportant. Position outer

clamps with bolt top and 30° either side of ver-

tical. Position relative to slot unimportant.

RIDING HEIGHT AND COIL SPRING SAG

The following check will quickly determine whether or

CHEVROLET CHASSIS SERVICE MANUAL

FRONT SUSPENSION 3-10

CHEVROLET, CHEVELLE, CAMARO AND CORVETTE (TYPICAL)
CHEVY H

Fig.
14- Shock Absorber

NOTE:
If necessary, tighten one more notch to

insert cotter pins.

3.
Place brake backing plate and wheel cylinder in posi*-

tion on steering knuckle and insert anchor pin.

4.
Place steering arm in position on back of steering

knuckle and insert two bolts through backing plate,

steering knuckle and steering arm. Install locknuts

and tighten. (See Specifications.)

5. Torque brake anchor pin (See Specifications).

6. Install brake shoes, except Corvette. (See Section 5.)

7. Install wheel hub, brake drum (or, on Corvette--

brake caliper and disc and hub assembly), wheel and

tire assembly over spindle.

8. Insert outer wheel bearing race and roller assembly,

washer and nut. Adjust front wheel bearing as shown

under Maintenance and Adjustments in this section.

Install new cotter pin, dust cap and hub cap.

9. Lower vehicle, recheck and readjust wheel alignment

where necessary.

SHOCK ABSORBER

Chevrolet, Chevelle, Comoro and Corvette (Fig. 14)

Removal

1.
With an open end wrench hold the shock absorber

upper stem from turning, and then remove the upper

stem retaining nut, retainer and rubber grommet.

2.
Remove the two bolts retaining the lower shock ab-

sorber pivot to the lower control arm and pull the

shock absorber assembly out from the bottom.

Installation

1.
With the retainer and rubber grommet in place over

the upper stem, install the shock abosrber (fully ex-
tended) up through the lower control arm and spring

so that the upper stem passes through the mounting

hole in the upper support arm.

2.
Install the rubber grommet, retainer' and attaching

nut over the shock absorber upper stem.

3.
With an open end wrench, hold the upper stem

from turning and tighten the retaining nut. (See

Specifications.)

4.
Install the two bolts attaching the shock abosrber

lower pivot to the lower control arm and tighten.

(See Specifications.)

Fig.
15 - Upper Control Arm Support Installed - Chevy II

CHEVROLET CHASSIS SERVICE MANUAL

FRONT SUSPENSION 3-12

2.
Remove forward nut, retainer and rubber bushing

from front end of strut rod.

3.
Remove two nuts from strut rod to lower control arm

bolts and remove bolts and washers.

4.
Withdraw strut rod from bracket.

5. Remove remaining rubber bushing, retainer, sleeve

and nut from strut rod.

6. Inspect rubber bushings for aging and replace if

necessary. *•

Installation

1.
Screw rear nu$ on forward end of rod and position it

approximately 3/4" from end of threads. Install

rear retainer, sleeve and bushing on rod so raised

pilot diameter faces forward.

2.
Insert strut rod in bracket so pilot diameter on bush-

ing pilots in hole in bracket. Install forward bushing

on sleeve so raised pilot diameter faces rear to

enter hole in bracket, then install forward retainer

and nut on rod.

3.
Attach strut rod to top of lower control arm with two

bolts,
washers and nuts.

4.
Lower vehicle to floor, check caster and camber

angles and adjust where necessary. Torque nuts as

shown in Specifications.

FRONT SPRING

Chevrolet

Removal

1.
With an open end wrench hold the shock absorber

upper stem from turning, and then remove the upper

stem retaining nut, retainer and rubber grommet.
I IVi" rVi"i

\>. j ii

>
I

5'4

s

WOOD
BLOCK
USED

WITH
CHEVROLET
ONLY

Fig.
19
- Spring Removal Tools - Chevrolet, Chevelle and Comoro

2.
With the car supported by the frame so that the con-

trol arms hang free, remove the wheel and tire as-

sembly (replace one wheel nut to retain the brake

drum),
shock absorber, stabilizer bar to lower con-

trol arm link, strut rod to lower control arm attach-

ing, nuts, bolts and lock washers and tie rod end.

3.
Scribe the position of the inner pivot camber adjust-

ing cam bolt and then remove the nut, lock washer

and outer cam.

4.
Install a steel bar (fabricated as shown in Figure 19)

through the shock abosrber mounting hole in the

lower control arm so that the notch seats over the

bottom spring coil and the bar extends inboard and

under the inner bushing. Fit a 5" wood block (See

Figure 19) between the bar and the bushing as shown

in Figure 20.

5.
With suitable jack or hoist, lift up slightly on the end

of the bar to remove the tension from the inner pivot

cam bolt, which can then be removed.

Fig.
18-Strut Rod

Pig. 20 - Front Spring Removal - Chevrolet

CHEVROLET CHASSIS SERVICE MANUAL

FRONT SUSPENSION ,3-13

6. Carefully lower the inner end of the control arm.

Tension on the spring will be removed before the

spring can be removed from the vehicle.

7.
Remove the spring.

Installation

1.
With the suspension set up as in Step 2 of the disas-

sembly procedure, insert a block of wood between the

upper control arm and the spring tower to keep the

arm up out of the way.

2.
Set the spring in place on the crossmember after

checking on proper positioning necessary.

3.
Install the steel bar and wood block as shown in Fig-

ure 20 and lift the control arm up until the inner

pivot cam bolt can be installed. ,

4.
Install the outer cam and loosely install the lock

washer and nut

5.
Set the cam bolt on the mark scribed during the re-

moval procedure and hold in this position while tight-

ening the nut (See specifications at the end of this

book).

6. Replace the strut rod to lower control arm nuts,

bolts and lock washers, the stabilizer bar link, the

shock absorber, the tie rod end, and the wheel and

tire.

7.
Lower vehicle to floor and install the shock absorber

upper stem retaining nut retainer and grommet.

8. Check the camber adjustment.

Chevelle and Camaro

Removal

1.
With an open end wrench hold the shock absorber up-

per stem from turning, and then, remove the upper

stem retaining nut, retainer and rubber grommet.

2.
With the car supported by the frame so that the con-

trol arms hang free, remove the wheel and tire as-

sembly (replace one wheel nut to retain the brake

drum),
shock absorber, and stabilizer bar to lower

control arm link.
4.

5.
Fig.
21 - Front Spring Removal - Chevelle & Camaro

Place a steel bar (fabricated as shown in Figure 19)

through the shock absorber mounting hole in the

lower control arm so that the notch seats over the

bottom spring coil and the bar extends outboard be-

yond the end of the control arm and slightly toward

the front of the car.

With a suitable jack or hoist lift up slightly on the

end of the bar.

Remove the lower ball stud cotter pin and attaching

nut and remove the ball stud from the knuckle.

ALTERNATE METHOD

Fig.
22 - Removing or Installing Front Coil Spring - Corvette (Typical)

CHEVROLET CHASSIS SERVICE MANUAL

FRONT SUSPENSION 3-15

4.
Insert Spring Compressor J-
6874-
4-
5 with Adapters

J-6874-8-9 into upp^r spring tower so that lower

MU"
bolt fits into shock absorber mounting holes in

spring seat (fig. 23). Secure the two lower studs to

the spring seat with nuts.

5.
Fit the tool upper pilot to top of spring and compress

spring by tightening upper nut (fig. 24). Compress

spring until screw is bottomed out.

6. Remove lower spring seat retaining nuts, lift spring

and seat assembly from control arm and guide it

down and out through fender skirt (fig. 25).

Spring Seat Replacement (Fig. 26)

1.
Release spring tension and disconnect spring com-

pressor from spring seat.

2.
Install new spring seat to spring compressor.

Installation

1.
If spring is to be replaced, install new spring into

tool and compress spring until screw is bottomed

out.

NOTE: Spring coil ends must be against spring

stops in upper and lower seats.

2.
Lift spring and tool assembly into place and position

so that the upper spring stop is inboard.

NOTE: Locating tab on upper spring seat may

be flattened before reinstalling spring.

3.
Install lower spring seat to control arm and torque

nuts as shown in the Specifications.

4.
Loosen spring compressor until spring is properly

seated in upper spring tower and remove.

5.
Install shock abosrber as outlined under Shock Ab-

sorber—Installation in this section.

Corvette

Removal

1.
With car on suitable hoist or jack, (support vehicle

by frame so control arms may swing free) remove

wheel and tire assembly, stabilizer bar and shock

absorber. Loosen the lower ball joint to steering

knuckle nut, and the' two lower control arm cross

shaft bushing bolts.

2.
Place Tool J-6874-1 across top of sixth coil (ap-

prox.),
then loosely secure Tool J-6874-2 to the up-

per shoe, with attaching capscrews and lock washers.

The upper shoe "V" notch and lower shoe raised land

should contact spring.

3.
Insert Tool J-6874 up through center of spring and

attach to upper and lower shoe assembly.

4.
Position spacers under shock absorber mounting hole

and against bottom of lower control arm. Install

special bearing washer and Tool J-6874-5. Locate

bearing against spacer and large washer against

bearing. Feed screw up through large washer bear-

ing and spacer and thread into Tool J-6874 and

tighten snugly (fig. 22).

5.
Center shoe assembly on spring and tighten screw

until a very slight compression is placed on spring

(fig. '22). Then firmly tighten down the two cap-

screws securing the upper and lower shoes to lock

these shoes to spring.

6. Turn head of screw until spring is compressed just

enough to clear the spring tower, then remove the

lower ball joint to steering knuckle nut (fig. 22).
NOTE: It may be necessary to assist the

spring out of the spring tower with a pry bar or

a similar tool.

7.
Disconnect the lower ball joint from the steering

knuckle and lower the control arm with the com-

pressed spring. Immediately release compression

on spring by backing off long screw. Release spring

and tool and withdraw spring.

CAUTION: The spring force under compres-

sion is very large. Exercise every safety pre-

caution when performing this operation to see

that individuals and materials subject to damage

are removed from the path of the spring when

the control arm is being lowered. Also, the

compressed spring
be relaxed immedi-

ately after lowering the control arm to reduce

the time of exposure to the large compressive

force.

Installation

1.
Position spring with closely coiled end up. Place

Tool J-6874-1 across the top of the sixth coil (ap-

prox.) then loosely secure Tool J-6874-2 to the

upper shoe with attaching capscrews and lock wash-

ers.
The upper shoe MV" notch and lower shoe

raised land should contact spring.

2.
Insert Tool J-6874 up through center of spring and

attach to upper and lower shoe assembly with bolt

and nut.

3.
Set spring in its seat on the lower control arm.

4.
Position spacers centrally under shock absorber

mounting hole and against bottom of lower control

arm. Install bearing, large washer and Tool

J-6874-5.
Locate bearing against spacer and large

washer against bearing. Feed the screw up through

large washer, bearing and spacer and thread into

yoke rod. Tighten snugly, but do not start to draw

down yet

5.
Center the shoe assembly on the spring and tighten

the lag screw until a very slight compression is

placed on spring, then firmly tighten down the two

capscrews securing the upper and lower shoes. This

will lock the shoes to the coil spring.

6. Turn head of screw until spring is compressed just

enough to clear the spring tower.

NOTE: It may be necessary to assist the

spring into the spring tower with a pry bar or

similar tool.

7.
Immediately install the lower ball joint into steering

knuckle and secure in place with attaching nut.

8. Release compression on spring and at the same time

use a drift to guide the coil spring into its proper

seat. End of coils must be 3/8" from coil stops in

spring seat.

9. Tighten the lower ball joint to steering knuckle nut

and lock with cotter key.

10.
Install shock absorber and stabilizer bar.

11.
Install wheel, tire and drum assembly.

12.
Remove car from hoist or jack stands.

13.
Tighten the two lower control cross shaft bushing

bolts to 45-55 lbs. ft. torque.

NOTE: If a suitable adjustable jack-stand is

CHEVROLET CHASSIS SERVICE MANUAL

FRONT SUSPENSION 3-16

available the following procedure may also be

used (fig. 22-Alternate Method).

1.
Support car on suitable hoist or jack (so control

arms may swing free) and remove the wheel and

tire assembly, shock absorber, and stabilizer link

at control arm.

2.
Place suitable jack stand under the lower control

arm cross shaft.

3.
Follow Steps 2-5 as outlined on previous page.

4.
Turn head of tool screw to partially compress

spring.

5. Remove the three control arm cross shaft attaching

bolts,
washers and nuts.

6. Carefully lower jack stand and if necessary increase

compression on spring and when coil spring is out of

its upper seat, relax tension on spring (fig. 22).

7. By using a pry bar to assist, if necessary, remove

the coil spring from the lower control arm.

8. Installation is the reverse of the above procedure.

Carefully follow instructions for installing spring

tool.

LOWER CONTROL ARM SPHERICAL JOINT

Chevrolet, Chevelle, Comoro and Corvette

Inspection

The lower control arm spherical joint should be re-

placed whenever wear is indicated in the upper joint

inspection.

NOTE: The lower control arm spherical joint

is a loose fit in the assembly when not connected

to the steering knuckle.

Only if inspection of each upper joint indicates them

both to be within limits, inspect each lower joint for ex-

cessive wear as follows:

1.
After reconnecting upper joints to steering knuckles,

support vehicle weight on wheels or wheel hubs.

2.
With outside micrometer or caliper, measure dis-

tance from top of lubrication fitting to bottom of ball

stud, and record the dimensions for each side.

3.
Then support vehicle weight at outer end of each

lower control arm, so that wheels or wheel hubs are

free,
then repeat Step 2.

4.
If the difference in dimensions on either side is

greater than 1/16" (.0625"), the joint is excessively

worn and both lower joints should be replaced.

If inspection of lower spherical joints does not indicate

excessive wear, inspect further as follows:

5.
On Chevrolet Only--Examine lubrication hole in each

joint assembly after cleaning out hole. Look for evi-

dence of the liner partially or fully blocking lubrica-

tion opening. Such evidence indicates that liner is

disintegrating and that both lower spherical joints

should be replaced.

Another indication of lower spherical joint excessive

wear is indicated when difficulty is experienced when

lubricating the joint. If the liner has worn to the point

where the lubrication grooves in the liner have worn

away, then abnormal pressure is required to force lubri-

cant through the joint. This is another reason to recom-

mend replacement of both lower joints.

If the above inspections do not indicate any reason for

spherical joint replacements, test the torque tightness of
Fig. 27 - Removing Lower Ball Joint - Chevelle
&
Camaro

the lower ball stud in the knuckle on each side as follows:

1.
Wire-brush off nut and cotter pin attaching spherical

joint ball stud to steering knuckle and examine for

evidence of looseness of stud in knuckle.

2.
If no evidence of looseness, remove cotter pin and

with prick punch or equivalent, mark nut stud and

knuckle to identify relative location.

3.
Tighten nut as installed and observe torque reading.

If less than 45 lbs. ft., stud may have been loose in

steering knuckle and replacement of both lower

spherical joints may be recommended.

4.
Check to see if torque of 60-94 lbs. ft. can be ob-

tained without bottoming stud or ball joint against

knuckle. If bottoming occurs, replace ball joint or

steering knuckle.

Chevrolet and Corvette

Removal

1.
Support lower control arm at outer end on floor jack,

with hoist or jack pad clear of lower ball stud nut.

2.
Remove upper and lower ball stud nuts, free ball

studs from steering knuckle and wire knuckle and

brake drum assembly up to fender skirt to preclude

interference while performing next step.

3.
Being careful not to enlarge the holes in control arm,

cut off rivets.

Installation

1.
Install new joint against underside of control arm and

CHEVROLET CHASSIS SERVICE MANUAL

FRONT SUSPENSION 3-17

4.
Replace the wheel and tire.

5.
Lower the vehicle.

Chevy II

inspection

Fig.
28 - Installing Lower Ball Joint - Chevelle & Camaro

retain in place with special bolts and nuts supplied

with new joint.

CAUTION: Use only alloy bolts supplied for

this operation. The special thick headed bolt

must be installed in the forward side of the

control arm.

2.
Tighten bolts and nut on ball stud to Specification

shown at the end of this book.

3.
Lubricate the joint.

Chevelle and Camaro

Removal

1.
Support lower control arm at outer end of floor jack,

with hoist or jack pad clear of lower ball stud and

remove the wheel.

2.
Remove the upper and lower ball stud nuts, free the

ball studs from the steering knuckle and wire the

knuckle and brake drum assembly out of the way to

preclude interference while completing the lower ball

stud removal procedure.

3.
Use a screw driver to pry off the seal and retainer.

Install Tools J-9519-10, J-9519-17 and J-9519-7 as

shown in Figure 27 and turn down on the hex head

screw until the ball stud is pushed out.

Installation

1.
Start the replacement ball stud into the control arm

and install Tools J-9519-10, J^9519-16 and J-9519-17

as shown in Figure 28.

2.
Turn down on the hex head screw until the ball stud

is seated properly in the control arm.

3.
Install the stud into the steering knuckle, secure in

place with the attacking nut and install the cotter pin.
1.
With upper control arm support in position as in

Figure 15, disconnect the lower ball stud from steer-

ing knuckle.

2.
Assemble nut to lower ball stud and check rotating

torque with torque wrench. Specifications for new

joints are 9 lbs. ft. If torque readings are exces-

sively high or low, replace ball joint.

Removal

1.
While vehicle weight is still on front wheels, position

support between upper control arm and frame side

rail (fig. 15).

2.
Raise vehicle and remove cotter pin and nut from

lower ball joint stud (fig. 29).

3.
Disconnect stabilizer at upper link. Break loose the

lower ball stud. Drop lower control arm until lower

ball joint is easily accessible.

, 4. Using a large chisel, cut off the three ball joint re-

taining plate rivet heads. It may be necessary to

drill out rivet heads before chiseling.

NOTE: Additional support to lower control

arm will be necessary to perform this operation.

5.
Remove ball joint from arm and clean arm.

6. Inspect ball joint seat and rivet holes for evidence of

fatigue such as cracking or bending. If defects are

evident, replace lower control arm as outlined later

in this section.

Installation

1.
Install ball joint in arm using special bolts furnished

with replacement kit.

NOTE: Use only special hardened bolts fur-

nished with this replacement kit. Do not attempt

to use other non-hardened bolts and do not at-

tempt to rivet replacement ball joint to arm.

Fig.
29- Disassembling Lower Ball Stud - Chevy

CHEVROLET CHASSIS SERVICE MANUAL