1967 CHEVROLET CAMARO steering wheel adjustment

STEERING 9-3

Fig.
4-Checking Wheel PuI!-Corvette

c. If torque does not lie within limits given in speci-

fications at rear of manual, adjustment is

necessary.

4.
Corvette and telescopic columns:

a. Use Tool J-5178 to measure.pull at rim of wheel

required to keep wheel in motion (fig. 4).

b.
If pull does not lie within limits given in specifi-

cations in rear of manual, adjustment of worm

bearings is necessary.

NOTE:
If vehicle is equipped with a tilt steer-

ing column, it will be necessary to disconnect

the steering coupling to obtain a torque reading

of the steering column. This torque should then

be subtracted from any reading taken on the

gear.

5. To adjust worm bearings, loosen worm bearing ad-

juster locknut and turn worm bearing adjuster shown

in Figure 3 until there is no perceptible end play in

worm. Check pull at steering wheel, readjusting: if

necessary to obtain proper pull. Tighten locknut and

recheck pull. If the gear feels "lumpy" after adjust-

ment of worm bearings, there is probably damage in

the bearings due to severe impact or to improper

adjustment and the gear must be disassembled for

replacement of damaged parts.

6. After proper adjustment of worm is obtained and all

mounting bolts securely tightened, adjust lash ad-

juster screw. First turn the steering wheel gently

from one stop all the way to the other, carefully

counting the total number of turns. Then turn wheel

back exactly half way, to center position. Turn lash

adjuster screw clockwise to take out all lash in gear

teeth, and tighten locknut. Check pull at steering

wheel taking highest reading as wheel is turned

through center position. See specifications in rear of

manual for proper sector lash adjustment. Readjust

if necessary to obtain proper pull.
NOT MORE THAN

T/a INCH FROM

CENTERLINE

Fig.
5—Steering Wheel Alignment

NOTE:
If maximum specification is exceeded,

turn las£ adjuster screw counterclockwise, then

come up on adjustment by turning the adjuster in

a clockwise motion.

7. Tighten locknut then recheck pull, as it must lie be-

tween specified readings.

Fig.
6—Adjusting Steering Ratio—Corvette

CHEVROLET CHASSIS SERVICE MANUAL

STEERING 9-4

8. Reassemble pitman arm to sector shaft, lining up

marks made during disassembly. Refer to torque

specifications at rear of manual for correct torque

value.

9. Install horn cap or ornament and connect steering

column harness at chassis connector.

NOTE:
Chevy.n models are equipped with a

shim at the frame to steering gear mounting

bolts.
Shims may be removed or installed as

required for proper steering gear alignment.

STEERING WHEEL ALIGNMENT AND

HIGH POINT CENTERING

1.
Set front wheels in straight ahead position. This can

be checked by driving vehicle a short distance on a

flat surface to determine steering wheel position at

which vehicle follows a straight path.

2.
With front wheels set straight ahead, check position

of mark on wormshaft designating steering gear high

point. This mark should be at the top side of the shaft

at 12 o'clock position and lined up with the mark in

the coupling lower clamp.

3.
If gear has been moved off high point when setting

wheels in straight ahead position, loosen adjusting

sleeve clamps on both left and right hand tie rods,

then turn both sleeves an equal number of turns in

the same direction to bring gear back on high point.

CAUTION: Turning the sleeves an unequal
number of turns or in differential directions will

disturb the toe-in setting of the wheels.

4.
Readjust toe-in as outlined in Section 3 (if necessary).

5. With wheels in a straight ahead position and the

steering gear on highpoint, check the steering wheel

alignment by measuring the distance from each hori-

zontal spoke to the horizontal centerline of the

steering wheel (fig. 5). If the horizontal spokes are

over 1-1/8 inches from the horizontal position the

wheel should be removed and centered. (See steering

wheel removal in this section.)

TOE-IN ADJUSTMENT

Adjust the steering linkage for proper toe-in setting as

outlined in Section 3.

CORVETTE STEERING RATIO (Fig. 6)

The Corvette steering ratio may be changed as follows:

CAUTION: Do not use the rearward hole in the

steering arm with power steering equipment or

interference may result.

1.
Remove tie rod ball stud nut at steering arm and

disconnect tie rod from steering arm.

2.
Move tie rod end to forward hole for 17.6:1 ratio

(fast ratio) or rear hole for 20.2:1 ratio (standard

ratio).

3.
Install tie rod stud nut and tighten securely. Repeat

operation on opposite steering arm.

COMPONENT REPLACEMENT AND REPAIRS

STEERING WHEEL

REGULAR PRODUCTION (Fig. 7)

Removal

1.
Disconnect steering column harness from chassis

wiring harness at connector (fig. 8).

2.
Pull out horn button cap or center ornament and

retainer.

3.
Remove three screws from the receiving cup.

4.
Remove the receiving cup, belleville spring, bushing,

and pivot ring.

5. Remove the steering wheel nut and washer.

6. Using Tool J-2927, install centering adapter on

steering shaft, thread puller anchor screws into

threaded holes provided in steering wheel. Turn

center bolt of tool clockwise to remove steering

wheel (fig. 9).

Installation

CAUTION: Direction signal control assembly

must be in "neutral position when assembling

steering wheel to prevent damage to cancelling

cam and control assembly.

1.
With directional cancelling cam and horn contact as-

sembly in place, set wheel onto steering shaft.
Fig. 7—-Regular Wheel and Horn Attachments

CHEVROLET CHASSIS SERVICE MANUAL

STEERING 9-10

SECTOR SHAFT SEAL REPLACEMENT

A faulty seal may be replaced without removal of

steering gear from car by removing pitman arm as out-

lined under Maintenance and Adjustments--Steering Gear

Adjustments and proceed as follows:

1.
Loose lash adjuster lock nut and turn lash adjuster

screw several turns counterclockwise.

2.
Remove three cap screws holding side cover to gear

bushing.

3.
Pull side cover and sector shaft from gear housing

as a unit. Do not separate side cover from sector

shaft.

4.
Pull sector shaft seal from gear housing using

hooked tool or pliers.

5. Coat new seal with chassis grease and position in

sector shaft bore.

6. Place a socket or piece of pipe of suitable diameter

on top of seal and drive seal into bore by tapping

pipe or socket with soft hammer.

7. Install sector shaft side cover assembly, being care-

ful not to damage new seal with splines on end of

shaft; splines may be wrapped with a few turns of

tape to prevent this.

8. Install new side cover gasket and align side cover on

gear housing and install cap screw.

9. Perform steering gear adjustment and install pitman

arm as outlined under Maintenance and Adjustments.

STEERING COLUMN

All models are equipped with new energy absorbing

steering columns. The columns are of five basic designs

as follows:

1.
Syncromesh. The syncromesh column is used on

models with standard, column mounted, conventional

shift levers. The shift tube, within the outer mast

jacket, includes two lower shift levers for connection

to the transmission control linkage.

2.
Automatic and floor shift. This column is used on

models equipped with column mounted powerglide

shift levers, or models with floor shift. If the ve-

hicle has the column mounted powerglide shift con-

trol, the inner shift tube has a single lower shift

lever for connection to the transmission control

linkage. On floor shift models, no lower shift levers

are present on the shift tube.

3.
Tilt wheel option. The upper end and steering shaft

of this column is specially designed to accommodate

the optional tilt steering wheel.

4.
Standard Corvette Column. The standard Corvette

column is similar in design to the Automatic and

Floor Shift column used on other models, except

no shift tube is used. Other differences are pointed

out in the disassembly and assembly procedures for

Standard Corvette column.

5. Telescopic wheel option. The upper end and steering

shaft of this column is specially designed to ac-

commodate the optional telescoping steering wheel.

To perform service procedures on steering column

upper end components, it is not necessary to remove the

column from the vehicle. The steering wheel, horn com-

ponents, turn signal switch, upper housing with bearing,

shift control lever, hazard warning knob, and upper shift

bowl may all be removed with the column remaining in

the vehicle. When servicing the above components, omit

the removal procedure and proceed with the applicable
disassembly procedures. Because of the numerous dif-

ferences in steering column types, be sure to refer to the

set of instructions below which apply to the exact column

to be serviced:

CAUTION: The outer mast jacket, shift tube, _

steering shaft, and instrument panel column

mounting b
racket

are designed as energy ab-

sorbing units. Because of the design of these

components, it is absolutely necessary to handle

the column with care when performing any serv-

ice operation required. Avoid hammering, jar-

ring, dropping, or leaning on any portion of the

column.

Removal

1.
Disconnect steering column harness at connector.

Disconnect neutral safety switch and back-up lamp

switch connectors if so equipped.

Remove steering wheel as outlined in this section.

Remove nuts and washers securing flanged end of

column to steering gear. On Chevy H models, re-

move nut and clamp bolt securing lower end of steer-

ing column to steering gear.

Disconnect transmission control linkage, if so

equipped, from lower column shift tube, levers.

Chevrolet and Chevy II only: Remove screws at-

taching upper and lower mast jacket covers together.

On Chevrolet, remove screws attaching lower cover

to instrument panel (figs. 15 and 18). Remove lower

cover.

Chevelle only: Remove screws securing mast jacket

trim cover to instrument panel and remove cover

(fig. 15).

Corvette, only: Remove screws securing escutcheon

to instrument panel. Remove screws securing upper

and lower covers together and remove covers.

On Chevrolet and Chevelle columns with Powerglide

shift levers, loosen set screw at six o'clock position

at bottom of column and remove the transmission

shift indicator pointer (fig. 15).

9. Chevrolet only (fig. 19):

a. Remove screws securing cover trim to dash

panel and remove cover trim.
2.

3.

4.

5.

6.

7.

8.

Fig.
18—Mast Jacket Cover Attachments—Chevy II

CHEVROLET CHASSIS SERVICE MANUAL

STEERING 9-18

I.D. of the lockplate with the slots in the top of the

jacket.

16.
Lock upper end assembly into position by pushing 18.

down on the cover assembly and rotating assembly

fully clockwise. Tangs on lock plate must engage

slots in jacket. 19.

17.
Tighten three turn signal switch mounting screws in
a gradual criss-cross sequence to avoid cocking the

lockplate.

Screw tolerance ring kit sections together leaving

enough inner edge exposed for later adjustment as

shown in Figure 35.

Slide wave washer and thrust washer over steering

shaft against upper bearing housing.

17 15 13 11 9 7 5 3

34 V33 29 27 26

36 35 32 3130 28

46 45 44 -43 42

Fig.
37—Tilt Steering Column—Exploded View

1.
Cover

2.
Steering Wheel Nut

3. Nut

4.
Seat

5.
Race

6. Screw

7. Turn Signal Switch

8. Bearing Assembly

9. Spring Retainer

10.
Lock Shoe Pin

11.
Shoe

12.
Bearing Housing
13.
Pivot Pin

14.
Shoe Springs

15.
Spring

16.
Release Lever Pivot

Pin

17.
Release Lever

18.
Bearing

19.
Upper Shaft

20.
Spring

21.
Sphere

22.
Wave Washer

23.
Lower Shaft
24.
Tilt Spring

25.
Screw

26.
Support

27.
Lock Shoe Guide

Pin

28.
Stop Plate

29.
Screw

30.
Retainer

31.
Thrust Washer

32.
Lock Plate

33.
Wave Washer

34.
Shift Lever Spring
35.
Shift Bowl

36.
Shroud

37.
Mast Jacket

38.
Dash Seal

39.
Shift Tube Assembly

40.
Adapter

41.
Bearing

42.
Tolerance Ring Kit

43.
Washer

44.
Retaining Ring

45.
Bolt

46.
Flange

CHEVROLET CHASSIS SERVICE MANUAL

STEERING 9-29

column mounting bracket, and place bracket in cor-

rect position on underside of instrument panel.

Loosely install bracket using bracket to column

mounting screws and bracket to instrument panel

washers and bolts.

NOTE: Steering shaft to gear clamp must be

tightened before column attaching bolts are

torqued. Refer to "Steering Gear-Chevy n",

installation procedure, for correct Chevy II

steering column alignment procedure.

5.
Camaro only (fig. 60):

Lay wedge shim in position on instrument panel

column mounting bracket and place bracket in cor-

rect position on underside of instrument panel.

Loosely install bracket using bracket to column

mounting screws, nuts, and washer and bolt as shown

in Figure 60.

6. Corvette only (fig. 61):

Loosely secure column mounting bracket to sup-

port plate and instrument panel with washers and

bolts.

7.
Secure flanged end of column to steering coupling

with lockwashers and nuts. On Chevy n, connect col-

umn to steering gear with clamp, clamp bolt, and

nut. On Corvette, slide steering shaft flange into

lower coupling
half,
and install upper clamp bolt

loosely; also secure support, seal and clamp loosely

at dash on engine side.

8. Tighten instrument panel mounting bracket bolts and

nuts.
Refer to torque specifications at rear of manual

for correct torque values.

9. Chevrolet only (fig. 15):

Place upper and lower mast jacket covers in po-

sition and secure covers together and to instrument

panel using nuts and screws as shown in Figure 15.

10.
Chevy H only (fig. 18):

Place lower mast jacket cover in position under

mast jacket and secure to upper cover with screws.

11.
CheveUe only (fig. 15):

Place mast jacket trim cover in position over col-

Fig.
61—Instrument Panel Mounting Bracket and

Support Plqte—Corvette
umn on underside of instrument panel and secure

with screws.

12.
Corvette only (fig. 14):

Slide escutcheon into position at instrument panel

and secure with screws. Place upper end lower

covers in position and secure with screws.

13.
On Chevrolet and CheveUe models with column

mounted powerglide controls, secure transmission

shift indicator pointer into position with set screw

(fig. 15). ,

14.
Chevrolet only (fig. 19):

a. Secure seal and cover to dash panel with screws.

b.
Place clamp assembly in position and install

clamp screw.

c. Install dash panel trim cover with mounting

screws.

15.
Chevelle only (fig. 20):

a. Secure seal and inner and outer covers to dash

panel with screws.

b.
Secure inner and outer covers together with

screws.

c. Install trim cover to dash panel with two

retainers.

16.
Chevy H only (fig. 21):

a. Secure seal, retainer, and clamp to dash panel

with screws.

b.
Install clamp screw.

c. Slide collar into position. Pinch and staple upper

tabs together.

17.
Camaro only (fig. 22):

a. Secure seal, upper cover, and lower cover to

dash panel with screws.

b.
Secure upper and lower cover together with

screws.

c. Fold rubber boot over securely against dash panel

to conceal covers.

18.
Corvette only (fig. 23):

a. Secure seal and support assembly to dash panel

on engine compartment side.

b.
Tighten clamp, washer, and clamp bolt on engine

compartment side.

19.
Connect transmission linkage to lower shift tube

levers in engine compartment, if column is so

equipped. Adjust levers as outlined in Section 7.

20.
Install steering wheel as outlined in this section.

21.
Connect directional signal, horn, back-up lamp, and

neutral start switch at wiring harness plugs. Adjust

back-up lamp, neutral start switch as outlined in

Section 12.

22.
Adjust steering gear and align and center steering

wheel as outlined in this section.

STEERING LINKAGE (Fig. 62)

TIE RODS

There are two tie rod assemblies used on all models.

Each assembly is of three piece construction, consisting

of a sleeve and two tie rod ends. The ends are threaded

into the sleeve and locked with clamps. Right and left

hand threads are provided to facilitate toe-in adjustment

and steering gear centering.

The tie rod ends are self-adjusting for wear and re-

quire no attention in service other than periodic lubrica-

tion and occasional inspection to see that ball studs are

tight. Replacement of tie rod ends should be made when

CHEVROLET CHASSIS SERVICE MANUAL

STEERING 9-31

Fig.
63—Freeing Ball Stud

rod threads with EP Chassis lube and install ends on

tie rod making sure both ends are threaded ah equal

distance from the tie rod.

2.
Make sure that threads on ball stud and in ball stud

nuts are perfectly clean and smooth. Install neoprene

seals on ball studs.

NOTE: If threads are not clean and smooth,

ball studs may turn in tie rod ends when at-

tempting to tighten nut.

3.
Install ball studs in steering arms and relay rod.

4.
Install ball stud nut, and install cotter pins. Lubri-

cate tie rod ends.

5.
Adjust toe-in as described in Section 3.

NOTE: Before locking clamp bolts on the rods,

make sure that the tie rod ends are in alignment

with their ball studs (each ball joint is in the

center of its travel). If the tie rod is not in

alignment with the studs, binding will result.

RELAY ROD-ALL MODELS EXCEPT CORVETTE

Removal

1.
Remove inner ends of tie rods from relay rod as

described under Tie Rod - Removal.

2.
Remove cotter pin and nut from relay rod ball stud

attachment at pitman arm.

3.
Detach relay rod from pitman arm. Shift steering

linkage as required to free pitman arm from relay

rod.

4.
Remove cotter pin and nut from idler arm and re-

move relay rod from idler arm.

Installation

1.
Install relay rod to idler arm, making certain idler

stud seal is in place, then install and tighten nut.

Advance nut just enough to align castellation with

cotter pin hole and install pin.

2.
Raise end of rod and install on pitman arm. Secure

with nut and cotter pin.
3.
Install tie rod ends to relay rod as previously

described under Tie Rods. Lubricate tie rod ends.

4.
Adjust toe-in (see Section 3) and align steering wheel

as described previously in this section under Steer-

ing Wheel Alignment and High Point Centering.

RELAY ROD-CORVETTE

Removal

1.
Remove steering damper from relay rod as outlined

under Steering Damper-Removal. Remove anchor

bracket from relay rod by disconnecting two mount-

ing bolts.

2.
Remove inner ends of tie rods from relay rod as

described under Tie Rod--Removal.

3.
Remove cotter pin from end of relay rod at pitman

arm ball stud attachment, and remove stud nut.

4.
Tap brJl stud out of pitman arm and lower relay rod.

5.
Remove cotter key and nut from idler arm and re-

move relay rod from idler arm. Remove washer and

seal from idler arm.

Installation

1.
Place relay rod on idler arm stud, making certain

idler stud seal and washer are in place, then install

and tighten nut. Advance nut just enough to align

castellation with cotter pin hole and install pin.

2.
Install new seal and clamp over ball at end of pitman

arm.

3.
Install inner spring seat and spring to relay rod.

4.
Raise end of rod and install on pitman arm.

5.
Install spring seat, spring, and end plug.

6. Tighten end plug until springs are compressed and

plug bottoms, then back off 3/4 turn plug amount

necessary to insert cotter pin. Insert cotter pin to

lock adjustment.

7.
Install tie rod ends to relay rod as previously de-

scribed under Tie Rods.

8. Lubricate tie rod ends and pitman arm to relay rod

ball joint.

9. Install steering damper bracket and tighten bolts.

Install damper as outlined under Steering Damper--

Installation.

10.
Adjust toe-in and align steering wheel as described

previously in this section.

IDLER ARM

Chevrolet, Chevelle, Comoro, and Corvette (Fig. 62)

Removal

1.
Remove idler arm to frame nut, washer, and bolt.

No washer is used on Corvette.

2.
Remove cotter pin and nut from idler arm to relay

rod ball stud.

3.
Remove relay rod from idler arm by tapping relay

rod with a hammer using a heavy hammer as a

backing.

4.
Remove idler arm.

Installation

1.
On Chevrolet, place seal in position on idler arm

stud; position stud up through frame, and secure with

lock washer and nut.

2.
On Chevelle, Camaro, and Corvette, position idler

CHEVROLET CHASSIS SERVICE MANUAL

STEERING
9-32

arm on frame and install mounting bolts, washers

and nuts. No washer is used on Corvette.

Install relay rod to idler arm, ^making certain seal

is on stud. Install and tighten nut.

Install cotter pin.

Refer to torque specifications at rear of manual for'

correct torque values.

Chevy II (Fig. 62}

Removal

1.
Remove cotter pin, nut and washer securing idler

arm to relay rod.

2.
Remove relay rod from idler arm.

3.
If equipped with power steering disconnect power

cylinder shaft from idler arm bracket.

4.
Remove three idler bracket to frame bolts and nuts

and remove bracket and idler arm assembly.

5.
Remove cotter pin, nut, washer and bolt securing the

idler arm to the bracket.

6. Press out the idler arm bushing for replacement.

Installation

NOTE: Installation must be done with front

wheels straight ahead or the car will lead to one

side.

1.
Install idler arm bushing, if previously removed.

NOTE: Make certain the outer sleeve of the

bushing does not protrude above surface of idler

arm.

2.
Reverse removal procedure and torque all nuts ac-

cording to specifications.

PITMAN ARM

Removal

1.
Remove cotter pin from pitman arm ball stud and

remove nut.

2.
Remove relay rod from pitman arm by tapping on

side of rod or arm in which the stud mounts with a

hammer while using a heavy hammer or similar tool

as a backing. Pull down on relay rod to remove

from stud.

3.
Remove pitman arm nut from sector shaft and mark

relation of arm position to shaft.

4.
Remove pitman arm with Tool J-6632 as shown in

Figure 2.

Installation

1.
Install pitman arm on sector shaft, lining up the

• marks made upon removal.

2.
Install sector shaft nut.

3.
Position relay rod on to pitman arm. Install nut.

Continue to tighten arm enough to align castellation

with hole in stud and install cotter pin.
STEERING ARM

If, through collision or other damage, it becomes nec-

essary to remove and replace either steering arm, pro-

ceed as follows:

Removal

1.
Remove tie rod from steering arm as outlined in this

section.

2.
Remove front wheel, hub and brake drum as a unit

by removing hub cap and dust cap, cotter pin from

spindle nut and the spindle nut. Pull assembly to-

ward outside of vehicle. If removal is difficult, it

may be necessary to back off brake adjustment to

increase brake shoe-to-drum clearance; see Hy-

draulic Brake Adjustment, Section 5. On models

with disc brakes, remove caliper and disc.

3.
With wheel and drum assembly or caliper and disc

removed, steering arm retaining bolt heads are ac-

cessible and removal of steering arm from vehicle

may be accomplished by removing retaining nuts.

Installation

1.
Place steering arm in position on vehicle and install

retaining bolts*

2.
Install nuts. Use only the special locknut listed for

this use in the Chevrolet Parts Catalog.

3.
Pack wheel bearings using a high quality wheel

bearing lubricant. Install bearings and wheel-hub-

brake drum assembly removed previously. On disc

brake models, install disc and caliper.

4.
Install keyed washer and spindle nut. Proceed as out-

lined under t{ Front Wheel Bearing Adjustment" in

Section 3.

5.
Install tie rod ball stud in steering arm. Be sure that

the dust cover is in place on ball stud.

6. Install castellated nut on ball stud, tighten securely

and install cotter pin.

7.
Following directions given in Section 3 to check cor-

nering wheel relationship and toe-in; correct as

required.

STEERING DAMPER-CORVETTE

Removal

1.
Remove bolt from damper pivot bracket at relay rod.

2.
Remove nut from damper pivot at frame bracket and

withdraw damper assembly.

Damper is serviced as a unit. Replace damper if
3.

damaged or excessively worn.

Installation

1.
Place piston rod end into frame bracket and install

retainers, bushings, and nut.

2.
Insert cylinder end pivot into relay rod bracket and

install through bolt.

CHEVROLET CHASSIS SERVICE MANUAL

STEERING
9-33

POWER STEERING

INDEX

Page

General Description
. 9-33

Maintenance
and
Adjustments
9-33

Bleeding Hydraulic System
9-33

Fluid Level
. 9-33

Adjustments
. 9-34

Power Steering Gear
. . 9-34

Pump Belt Tension
9-34
Hydraulic System Checks
9-34

Component Replacement
and
Repairs
. 9-35

Power Steering Pump.
. 9-35

Power Steering Gear
9-36

Control Valve
and
Adapter Assembly
9.35

Power Cylinder
9.37

Power Steering Hoses
9.39

GENERAL DESCRIPTION

Two types
of
power steering
are
used
for 1967.
One
is

the conventional linkage type
for
Chevy
n and
Corvette

vehicles
and the
other
is the
integral gear type
for

Chevrolet, Chevelle,
and
Camaro.
For
both types
the

hydraulic pressure
is
provided
by an
engine-driven vane-

type pump.

On
the
Chevy
n and
Corvette linkage type power steer-

ing, hydraulic pressure
is
delivered through
a
hose from

the pump
to a
valve which senses
the
requirement
for

power assistance
and
supplies
the
power cylinder
ac-

cordingly.
The
steering gear used with this power steer-

ing
is the
same basic unit used
on
manually steered

vehicles;
it is
serviced
as
outlined
in the
manual steering

part
of
this section except
for
adjustment, which
is

covered
in the
following pages.
The
steering linkage also

is serviced the same
as
manual counterparts.

The Chevrolet, Chevelle
and
Camaro integral gear type

power steering
has the
hydraulic pressure delivered

from
the
pump through two hoses
to the
steering gear.
In
the power steering gear
the
steering shaft, hydraulic

valve, worm, and rack-piston
nut are all in
line making
a

compact
and
space saving assembly.
All oil
passages
are

internal within
the
gear except
the
pressure
and
return

hoses.

The steering gear
is a
recirculating ball system
in

which steel balls
act as a
rolling thread between
the

steering worm
and
rack-piston
nut. The
rack-piston
nut

is
all one
piece
and is
geared
to the
sector
of
the piston

shaft.
The
valve
is
contained
in the
gear housing elimi-

nating
the
need
of
bolts
or
seals
to
attach
a
separate

valve housing.

The valve
is an
open-center, rotary-type three
way

valve.
The
spool
is
held
in
neutral position by means
of a

torsion
bar. The
spool
is
attached
by
means
of
the stub

shaft
to one end of the
torsion
bar
and
to the
valve body

on
the
other
end.
Twisting
of the
torsion bar allows
the

spool
to
move
in
relation
to the
valve body thereby oper-

ating
the
valve.

MAINTENANCE
AND
ADJUSTMENTS

BLEEDING HYDRAULIC SYSTEM

1.
Fill
oil
reservoir
to
proper level and
let oil
remain

undistrubed
for at
least two minutes.

2.
Start engine
and run
only
for
about
two
seconds.

3.
Add
oil if
necessary.

4.
Repeat above procedure until
oil
level remains
con-

stant after running engine.

5. Raise front
end of
vehicle
so
that wheels
are off
the

ground.

6. Increase engine speed
to
approximately
1500 rpm.

7. Turn
the
wheels
(off
ground) right
and
left, lightly

contacting
the
wheel stops.

8. Add
oil if
necessary.

9. Lower
the car and
turn wheels right and left
on the

ground.

10.
Check
oil
level and refill
as
required.

11.
If oil is
extremely foamy, allow vehicle
to
stand
a

few minutes with engine
off and
repeat above

procedure.
,

a.
Check belt tightness
and
check
for a
bent
or
loose

pulley. (Pulley should
not
wobble with engine

running.)
b.
Check
to
make sure hoses
are not
touching
any

other parts
of the car,
particularly sheet metal.

c. Check
oil
level, filling
to
proper level
if
neces-

sary, following operations
1
through
10.
This

step
and
Step
"D" are
extremely important
as

low
oil
level and/or
air in the oil are the
most

frequent causes
of
objectionable pump noise.

d. Check
the
presence
of air in the oil. If air is

present, attempt
to
bleed system
as
described
in

operations
1
through
10. If it
becomes obvious

that
the
pump will
not
bleed after
a few
trials,

proceed
as
outlined under Hydraulic System

Checks.

FLUID
LEVEL

1.
Check
oil
level
in the
reservoir
by
checking
the dip

stick when
oil is at
operating temperature.
On

Chevelle models equipped with remote reservoir,

the reservoir should
be
maintained approximately

3/4 full when
oil is at
operating temperature.

2.
Fill,
if
necessary,
to
proper level with
GM
Power

Steering Fluid
or, if
this
is not
available, automatic

CHEVROLET CHASSIS SERVICE MANUAL