1967 CHEVROLET CAMARO transmission oil

REAR SUSPENSION AND DRIVE LINE 4-35

Fig.
91—
Removing Carrier Front Support

PINION FLANGE, DUST DEFLECTOR

AND/OR OIL SEAL

Removal

1.
Raise vehicle and place jackstand under frame to

allow wheels to hang free.

2.
Place 1/2" thick block of wood or steel between

carrier upper surface to rear of companion flange,

and body floor. This will prevent carrier assembly

from twisting upward when front support bracket is

disconnected.

3.
Disconnect carrier front mounting bracket bolt from

frame crossmember.

4.
Remove nut from carrier bracket front bolt and

slide bolt to one side until bolt head contacts floor

well. Mark the floor well at this point and drill a

3/4"
diameter hole - remove bolt.

5. Loosen bracket rear bolt and swing bracket down

and to the rear (fig. 91).

6. Disconnect propeller shaft at transmission and at

companion flange. Slide transmission yoke forward,

and lower propeller shaft down and out.

7. Mark companion flange nut and pinion relative loca-

tion.
This is necessary to reset original pinion

bearing pre-load during reassembly of companion

flange.

8. Attach J-8614-1 companion flange holder and remove

flange nut and washer (fig. 92).

9. Remove companion flange by driving off with brass

drift and hammer (fig. 93).

10.
Using screw driver, pry oil seal out of carrier.

Inspection

Inspect companion flange splines for excessive wear

or twisting and check deflector for looseness. If de-

flector is loose or damaged, break stake marks and

remove. Install new deflector and stake in place.

Installation

1.
Place sealing compound around O.D. of new seal

and install seal in carrier using seal Installer

J-21057 (fig. 94).
Fig.
92—Removing Companion Flange Nut

NOTE:
Seal should be started squarely in bore

to eliminate seal distortion.

2.
Tap seal into position until there is a 1/8" gap be-

tween seal flange and carrier (fig. 95).

3.
Lubricate companion flange splines and tap into

place.

4.
Install companion flange washer and nut, and tighten

nut so that it lines up with mark on pinion.

5. Raise propeller shaft into position and connect to

companion flange and transmission yoke.

6. Place rubber cushion on carrier front mounting

bracket and raise bracket into position and loosely

install nut.

7. Install carrier bracket front bolt. With vehicle at

curb,
torque all affected parts to specifications and

install cotter pin to carrier bracket front bolt.

8. Insert a plastic plug from the inside of the floor

well to prevent dust and water entry.

Fig.
93—Removing Companion Flange

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION AND DRIVE LINE 4-36

Fig.
94—Installing Pinion Oil Seal

DIFFERENTIAL CARRIER

Removal

1.
Disconnect spring end link bolts as outlined in

Spring—Removal, in this section.

2.
Disconnect axle drive shafts at carrier by removing

"U"
bolts securing trunnion to side gear yoke.

3.
Disconnect carrier front support bracket at frame

crossmember.

4.
Disconnect propeller shaft at transmission and at

companion flange. Slide transmission yoke forward

into transmission. Drop propeller shaft down and
Fig.
95-Pinion Sea! Installed

out toward the rear.

5. Mark camber cam and bolt relative location on strut

rod bracket and loosen cam bolts.

6. Remove four bolts securing bracket to carrier lower

surface and drop bracket. Remove camber cam bolts

and swing strut rods up and out of the way.

7. Remove eight carrier-to-cover bolts. Loosen bolts

gradually to allow lubricant to drain out.

8. With mounting bolts removed, pull carrier partially

out of cover, drop nose to clear crossmember and

gradually work carrier down and out.

Installation

1.
Clean inside of carrier cover and liberally grease

gasket surface. Place new gasket on cover.

2.
Cut heads off two l/2"-13 x 1-1/4" bolts and slot

unthreaded end. Install these aligning studs into two

below-center carrier bolt holes, one on each side.

3.
Raise carrier into position aligning studs into

cover (fig. 96).

4.
Install carrier-to-cover bolts and tighten securely.

5. Connect propeller shaft to companion flange and

transmission yoke.

6. Install rubber cushion on bracket and position to

frame crossmember. Install hut and torque to

specifications.

7. Raise axle drive shafts into position and assemble

inboard trunnion to side gear yokes with "U" bolts.

8. Assemble strut rods to bracket and raise bracket

into position under carrier. Install four bolts and

torque to specifications. Move camber cams to

marked location and tighten cam nuts.

Fig.
96—Installing Carrier Assembly

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION
AND
DRIVE LINE
4-38

•"•f •--..—-.>•,«.-. ^

Fig. 99—Heavy-Duty Propeller Shaft Cross-Section

(Saginaw Design)'

in
the
propeller shaft yokes. Conventional snap rings are

used
as
one method—these units can be disassembled and

reassembled using
the
same trunnions
if
desired.
How-

ever, the alternate method
of
retaining the trunnions does

not permit reusing
the
trunnions once they have been
pressed from the yokes. These trunnions are retained by

nylon material which
is
injected through
a
small hole
in

the yoke and into
the
annular grooves between the trun-

nion and yoke.

COMPONENT PARTS REPLACEMENT

PROPELLER SHAFT (DANA)

Removal

1.
Raise vehicle, mark relationship
of
shaft
to com-

panion flange and disconnect the rear universal joint

by removing trunnion bearing "U" bolts
(fig. 101).

Tape bearing cups
to
trunnion
to
prevent dropping

and loss of bearing rollers.

NOTE:
On
Corvette models, remove trunnion

"U"
bolts at transmission yoke also.

2.
Withdraw propeller shaft front yoke from transmis-

sion
by
moving shaft rearward, passing
it
under the

axle housing. Watch
for oil
leakage from transmis-

sion output shaft housing.

Repairs

NOTE:
The
universal joints
(fig. 102) are of
Fig.
101—
Removing Propeller Shaft from Companion Flange

the extended-life design
and do not
require

periodic inspection or lubrication; however, when

Fig.
100—Propeller Shaft Sleeve
and
Damper Assembly
Fig. 102—Propeller Shaft Trunnion (Dana Design)

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION AND DRIVE LINE 4-40

Fig.
106—Removing Propeller Shaft from Companion Flange

PROPELLER SHAFT (SAGINAW)

Removal

1.
Raise vehicle sufficiently to permit access to propel-

ler shaft and mark relationship of rear yoke to

companion flange.

2.
Remove trunnion bearing retaining strap attaching

screws from both bearings (fig. 106).

3.
Lower rear of propeller shaft, being careful not to

dislodge bearing caps from trunnion, and tape bear-

ing caps to trunnion.

4.
Withdraw propeller shaft front yoke from transmis-

.sion by moving shaft rearward, passing it under the

axle housing. Watch for oil leakage from transmis-

sion output shaft housing.

Repairs

NOTE:
Because of the elastic properties of the

nylon retainers, the trunnions must be pressed

from the yokes. Pressing the trunnions from the

yokes will shear the retainers which renders

the bearing caps unsuitable for reuse. A service

Jdt, which employs a snap ring to retain the

trunnion, must be used when reassembling the

propeller shaft (fig. 107).

1.
Remove trunnion at differential end of propeller shaft

Fig.
107—Service Kir Trunnion (Saginaw)
Fig.
108—Pressing Trunnion Bearing from Propeller Shaft

using the following procedure:

a. Support trunnion on a press bed so that the

propeller shaft yoke can be moved downward.

Support front of propeller shaft so that shaft is

in a horizontal position.

b.
Using a piece of pipe or similar tool, with an ins-

side diameter slightly larger than 1 1/8", press

bearing from yoke (fig. 108).

c. Apply force on yoke around bearing until nylon

retainer breaks. Continue to apply force until the

downward movement of the yoke forces the bear-

ing as far as possible from the yoke (fig. 109).

d. Complete removal of bearing by tapping around

circumference of exposed portion with a small

hammer (fig. 110).

e. Rotate propeller shaft so that opposite bearing

-may be removed in the manner described above.

f. Remove trunnion from yoke.

Remove trunnion at transmission end of propeller

shaft using the following procedure:

a. Support splined yoke on a press bed and the rear

of the propeller shaft on a stand so that shaft is

horizontal. Be sure that weight is evenly dis-

tributed on each side of the splined yoke and that

the fixed yoke half of the "U" joint is free to

move downward.

b.
Using a piece of pipe or similar tool, with an

inside diameter slightly larger than 1 1/8", press

bearing from yoke (fig. 108).

c. Apply force on yoke around bearing until nylon

retainer breaks. Continue to apply force until the

downward movement of the yoke forces the bear-

ing as far as possible from the yoke (fig. 109).

d. Complete removal of bearing by tapping around

circumference of exposed portion with a small

hammer (fig. 110).

e. Rotate propeller shaft so that opposite bearing

may be removed in the manner described above.

f. Remove splined yoke and trunnion from propeller

shaft.

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE 6-6

CHOKE VALVE

COMPLETELY

CLOSED

PULL UPWARD ON

ROD TO END OF

TRAVEL

BEND ROD

TO ADJUST
ROD IN BOTTOM

OF SLOT

BOTTOM OF

ROD SHOULD

EVENWITH

TOP OF

HOLE
CHOKE VALVE

CLOSED

BOTTOM OF

ROD SHOULD

BE EVEN WITH

TOP OF HOLE

TOP OF ROD

SHOULD BE EVEN

WITH BOTTOM

OF HOLE (CHOKE

CLOSED)

^..BEND ROD TO

ADJUST

_PULL DOWNWARD

ON ROD TO CON-

TACT STOP

L6 (TYPICAL)

V8 327-275 HP

V8 350-295 HP
BEND ROI

TO ADJUST

PULL UPWARD ON

ROD TO CONTACT

STOP ON BRACKET

ALL V8 (EXCEPT 327-275 HP

AND 350-295 HP)

Fig.
11 - Remote Choke Adjustment

sequence outlined on Torque Sequence Chart. A slight

leak at the intake manifold destroys engine performance

and economy.

Service Fuel Lines and Fuel Filter

1.
Inspect fuel lines for kinks, bends or leaks and cor-

rect any defects found, • • •

2.
Inspect filter and replace if plugged.

NOTE:
If a complaint of poor high speed per-

formance exists on the vehicle, fuel pump tests

described in Section 6M should be performed.

Service Cooling System

1.
Inspect cooling system for leaks, weak hoses, loose

hose clamps and correct coolant level, and service

as required.

NOTE:
A cooling system pressure test, as de-

scribed in "Additional Checks and Adjustments"

in this section, may be performed to detect

internal or external leaks within the cooling

system.

Check and Adjust Accelerator Linkage

1.
Disconnect accelerator rod at carburetor throttle

lever.

2.
Hold carburetor throttle lever in wide position.

3.
Pull accelerator rod to wide open position. (On ve-

hicles equipped with automatic transmission, pull

through detent).

4.
Adjust accelerator rod to freely enter hole in carbu-

retor throttle lever.'

NOTE:
Accelerator linkage is outlined in de-

tail in Section 6M.
5. Connect accelerator rod at throttle lever.

Service Crankcase Ventilation (Fig. 10}

All engines have either "Positive" or "Closed Positive"

ventilation systems utilizing manifold vacuum to draw

fumes and contaminating vapors into the combustion

chamber where they are burned. Since it affects every

part of the engine, crankcase ventilation is an important

function and should be understood and serviced properly.

In both "Positive" and "Closed Positive" ventilation,

air is drawn through the engine, (through a regulating

valve) into the manifold, drawing' crankcase vapors and

fumes with it to be burned. "Positive" ventilation uses a

vented-meshed cap for clean air intake to the engine,

while . "Closed Positive" ventilation system draws the

clean air from the carburetor air cleaner and has a

nonvented oil filler cap.

1.
Ventilation valve may be checked as outlined under

"Additional Checks and Adjustments".

2.
Inspect for deteriorated or plugged hoses.

3.
Inspect all hose connections.

4.
On closed positive ventilation systems, remove flame

arrestor and wash in solvent then dry with com-

pressed air.

Service Air Injection Reactor System

Inspect air injection reactor system for evidence of

leaks,
deteriorated hoses, cracked air manifolds or tubes

and loose hose clamps. Inspect air injection pump belt

condition and tension. Make all necessary repairs as

outlined in "Section 6T".

Because of the relationship between "Engine Tune Up"

and "Unburned Exhaust Gases", the condition of Engine

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE
6-8

Check
and
Adjust Ignition Timing
(Fig. 13)

1.
Disconnect
the
distributor spark advance hose
and

plug
the
vacuum source opening.

2.
Start engine
and run at
idle speed
(see
tune
up
chart).

3.
Aim
timing light
at
timing
tab.

NOTE:
- The
markings
on the
tabs
are in 2°

increments
(the
greatest number
of
markings
on

the
"A"
side
of the "O"). the "O"
markings
is

TDC
of
#1 cylinder
and all
BTDC settings fall
on

the
"A"
(advance) side
of "O".

4.
Adjust
the
timing
by
loosening
the
distributor clamp

and
,
rotating
the
distributor body
as
required, then

tighten
the
clamp.

5.
Stop engine
and
remove timing light
and
reconnect

the spark advance hose.

Adjust Idle Speed
and
Mixture
(Fig. 14)
(Except when

equipped with
Air
Injection Reactor System)

1.
As a
preliminary adjustment, turn idle mixture

screws lightly
to
seat
and
back
out 2
turns.

CAUTION:
Do not
turn idle mixture screw

tightly against seat
or
damage
may
result.

2.
With engine running
at
operating temperature (choke

wide open) adjust idle speed screw
to
bring idle

speed
to
specified
rpm
(automatic transmission
in
drive, manual transmission
in
neutral).

3.
Adjust idle mixture screw
to
obtain highest steady

idle speed
(1/4
turn
out
from lean roll).

4.
Repeat Steps
2 and 3 as
needed
for
final adjustment.

5.
Shut down
the
engine, remove gauges
and
install
air

cleaner.

Adjust Idle Speed
and
Mixture
(Fig. 14)
(With
Air

Injection Reactor System)

The recommended adjustment procedure
for Air
Injec-

tion Reactor System equipped engines
is as
follows:

1.
As a
preliminary adjustment, turn idle mixture

screws lightly
to
seat
and
than back
out 3
turns.

CAUTION:
Do not
turn idle mixture screw

tightly against seat
or
damage
may
result.

2.
With engine running
at
operating temperature, choke

wide open,
and
parking brake applied, adjust idle

specified idle speed (automatic

"drive"-manual transmission
in
to

in
screw

transmission

"neutral").

;3.
Adjust idle mixture screw (turn
in) to
"lean roll"

position; then turn screw
out 1/4
turn
(1/4
turn rich

from "lean roll").
The
definition
of
"lean roll" point

is
a 20 to 30 rpm
drop
in
engine speed, obtained
by

leaning
the
idle mixture.

4.
Repeat Steps
2 and 3 as
needed
for
final adjustments.

ADDITIONAL CHECKS
AND
ADJUSTMENTS

Testing Crankcase Ventilation Valve
(Fig. 15) 0

1.
Connect tachometer
and
vacuum gauge
as for
idle

speed
and
mixture adjustment.

2.
Set
parking brake, start engine
and
adjust idle speed

and mixture.

3.
Disconnect ventilation hose
at
valve, block opening
of

valve
and
read engine
rpm
change.

4.
A
change
of
less than
50 rpm
indicates
a
plugged

ventilation valve
-
replace
the
valve.

Cylinder Balance Test
(Fig. 16)

It
is
often difficult
to
locate
a
weak cylinder.
A com-

pression test,
for
example, will
not
locate
a
leaky intake

manifold,
a
valve
not
opening properly
due to a
worn

camshaft,
or a
defective spark plug.

With
the
cylinder balance test,
the
power output
of one

cylinder
may be
checked against another, using
a set of

grounding leads. When
the
power output
of
each cylinder

is
not
equal,
the
engine will lose power
and run
roughly.

Perform
a
cylinder balance test
as
follows:

1.
Connect
the
tachometer
and
vacuum gauge.

2.
Start engine
and run at 1500 rpm.

3.
Ground large clip
of
grounding leads
and
connect
in-

dividual leads
to all
spark plugs except
the
pair being

tested.

Divide
the
firing order
in
half
and
arrange
one
half

over
the
other.
The
cylinders
to be
tested together
ap-

pear
one
over
the
other.

L4 Firing Order
V8 Firing Order

1-8-4-3-6-5-7-2

1-6, 8-5, 4-7, 3-2

1-3-4-2
= 1-3

4-2

L6 Firing Order

1-5-3-6-2-4
=
=
1-4. 3-2

1-5-3

6-2-4
1-6, 5-2, 3-4
1-8-4-3

6-5-7-2

4.
Operate engine
on
each pair
of
cylinders
in
turn
and

note engine
rpm and
manifold vacuum
for
each pair.

A variation
of
more than
1
inch
of
vacuum
or 40 rpm

between pairs
of
cylinders being tested indicates that

the cylinders
are off
balance.

Battery

The battery should
be
checked with special testing

equipment
and to the
equipment manufacturers specifica-

tions.
See
Section 6Y
for
complete information
on
battery

tests.

Ignition

The following additional ignition checks
may be
made

with
any of
several pieces
of
equipment available
for un-

covering
the
source
of
engine difficulties.
The
specific

operating instructions
of the
equipment manufacturer

should
be
followed:

Cranking voltage

Ignition switch

Distributor resistance

Secondary resistance

Ignition output
and
secondary leakage

Cranking Voltage
(Fig. 17)

1.
Disconnect coil primary lead
at the
coil negative

terminal
to
prevent engine from firing during

cranking.

2.
Connect voltmeter between primary terminal
of coi|

(resistance wire side)
and
ground.

3.
Operate starting motor.

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE 6-14

b.
Bolt transmission to engine, then raise engine and

transmission assembly and install flywheel to

converter attaching bolts.

c. Install converter
housing*
underpan and starter.

3.
Tilt and lower engine and transmission assembly into

the chassis as a unit, guiding engine to align front

mounts with frame supports.

4.
Install front mount through bolts and torque to

specifications.

5.
Raise engine enough to install rear crossmember,

then install crossmember, install rear mount, lower

engine and torque bolts to specifications.

6. Remove lifting device and lifting adapter then install

rocker arm cover as outlined.

7.
On synchromesh equipped vehicles, install clutch

cross shaft engine bracket, then adjust and connect

clutch as outlined in Section 7.

8. Connect:

• Speedometer cable.

• Shift linkage at transmission.

9; Install propeller shaft.

10.
Remove jack stands and lower vehicle.

11.
Connect:

Power steering pump lines (if disconnected).

Vacuum line to power brake unit (if disconnected).

Fuel line at fuel pump.

Exhaust pipe at manifold flange.

Accelerator linkage at manifold bellcrank.

12.
Connect wires at:

Coil

Oil pressure switch

Temperature switch

Delcotron

Starter solenoid

13.
Install pulley, fan blade and fan belt as outlined in

Section 6K.

14.
Install radiator and shroud as outlined in Section 13.

15.
Install and adjust hood as outlined in Section 11.

16.
Connect battery cables.

17.
Fill with coolant, engine oil and transmission oil,

then start engine and check for leaks.

18.
Perform necessary adjustments and install air

cleaner.

MANIFOLD ASSEMBLY

Removal

1.
Remove air cleaner.

2.
Disconnect both throttle rods at bellcrank and re-

move throttle return spring.

3.
Disconnect fuel and vacuum lines at carburetor.

Disconnect choke cable on \A engines.

4.
Disconnect crankcase ventilation hose at rocker arm

cover.

5.
Disconnect exhaust pipe at manifold flange and dis-

card packing.

6. Remove manifold attaching bolts and clamps then

remove manifold assembly and discard gaskets.

7.
Check for cracks in manifold castings.

8. If necessary to replace either intake or exhaust

manifolds, separate them by removing one bolt and

two nuts at center of assembly. Reassemble mani-

folds using a new gasket. Tighten finger tight and

torque to specifications after assembly to cylinder

head. Transfer all necessary parts.
Installation

1.
Clean gasket surfaces on cylinder head and

manifolds*

2.
Position new gasket over manifold end studs on head

and carefully install the manifold in position making

sure the gaskets are in place.

3.
Install bolts and clamps while holding manifold in

place with hand.

4.
Torque bolts to specifications.

NOTE: On L6 engines center bolt and end bolt

torque differ.

5.
Connect exhaust pipe to manifold using a new

packing.

6. Connect crankcase ventilation hose at rocker arm

cover.

7.
Connect fuel and vacuum lines at carburetor.

8. On L4 engines connect choke cable and adjust as out-

lines in Section 6M.

9. Connect throttle rods at bellcrank and install throttle

return spring.

10.
Install air cleaner, start engine, check for leaks and

adjust carburetor idle speed and mixture.

ROCKER ARM COVER

Removal

1.
Disconnect crankcase ventilation hose(s) at rocker

arm cover.

2.
Remove air cleaner.

3.
Disconnect temperature wire from rocker arm cover

clips.

4.
Remove rocker arm cover. '

CAUTION: Do Not pry rocker arm cover loose

Gaskets adhering to cylinder head and rocker

arm cover may be sheared by bumping end of

rocker arm cover rearward with palm of hand or

a rubber mallet.

Installation

1.
Clean gasket surfaces on cylinder head and rocker

arm cover with degreaser then, using anew gasket,

install rocker arm cover and torque bolts to

specifications.

2.
Connect temperature wire at rocker arm cover clips.

3.
Install air cleaner.

4.
Connect crankcase ventilation hoses.

VALVE MECHANISM

Removal

1.
Remove rocker arm cover as outlined.

2.
Remove rocker arm nuts, rocker arm
balls,
rocker

arms and push rods.

NOTE:
Place rocker arms, rocker arm balls

and push rods in a rack so they may be rein-

stalled in the same location.

Installation and Adjustment

NOTE:
Whenever new rocker arms and/or

rocker arm balls are being installed, coat bear-

ing surfaces of rocker arms and rocker arm

balls with Molykote or its equivalent.

1.
Install push rods,

socket.
Be sure push rods seat in lifter

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE 6-17

Fig.
5L
-
Engine Blocked for Pan Removal

NOTE: Do not install rocker arm cover.

11.
Start engine and allow warm up then retorque cylin-

der head
as
outlined in Step 4 and readjust valves as

outlined under Engine Tune Up.

OIL PAN

Removal

Chevrolet
and Camaro

1.
Disconnect battery positive cable.

2.
Remove through bolts from engine front mounts.

3.
Drain radiator, then disconnect upper and lower ra-

diator hoses at radiator.

4.
Remove fan blade as outlined in Section 6K.

5.
Raise vehicle then drain engine oil.

6. Disconnect and remove* starter.

7.
On
vehicles equipped with automatic transmission,

disconnect transmission cooler lines at transmission

and remove converter housing underpan.

8. Disconnect steering
rod at
idler lever then swing

steering linkage for oil pan clearance.

9. Rotate crankshaft until timing mark
on
torsional

damper is at 6:00 o'clock position.

10.
Using
a
suitable jack (and a block of wood to prevent

damaging oil pan), raise engine enough to insert 2"
x

4"
wood blocks under engine mounts (fig. 5L), then

lower engine onto blocks.

NOTE:
If
2"
x
4" wood blocks are cut 5-1/2"

long they can be used on all Chevrolet engines.

The 5-1/2" length up for in line engines and the

4"
side up for V8 engines.

11.
Remove oil pan and discard gaskets and seals.

Cfievel/e

1.
Remove enginfe from vehicle as outlined.

2.
Place engine on jack stands, one at each front mount

and one at transmission extension.

CAUTION: Leave engine lift attached
to
en-

gine.
Do not remove all weight
of
engine from

engine lift.

3.
On
vehicles equipped with automatic transmissions

remove converter housing underpan.

4.
Remove starter.

5.
Remove oil pan and discard gaskets and seals.
Chevy//

1.
Disconnect battery positive cable.

2.
Drain engine oil.

3.
Disconnect then remove starter.

4.
Disconnect-steering idler arm bracket at right hand

frame rail and swing steering linkage down for pan

clearance.

5.
On L6 engines, remove front crossmember.

NOTE:
On
station wagon
let
stabilizer
bar

hang while removing crossmember.
"

6. Remove oil pan and discard gaskets and seals.

Installation

1.
Thoroughly clean all gasket sealing surfaces.

NOTE: Use
a
new pan gasket set.

2.
Install rear seal in rear main bearing cap.

3.
Install front Seal on crankcase front cover pressing

tips into holes provided in cover.

4.
Install side gaskets on cylinder block (fig. 6L).

5.
Complete installation as follows:

Life

1
i

If ^
jfp^;.^3p
>\~^^ \s3^^r' -'••'•'-^^Hll

|^=-5p|:*iil^
mm

Fig.
6L
-
Pan Gaskets and Seals

CHEVROLET CHASSIS SERVICE MANUAL