1967 CHEVROLET CAMARO engine oil

ELECTRICAL-BODY AND CHASSIS 12-34

5. To replace, reverse the removal procedure.

SPEEDOMETER REPLACEMENT

1.
Remove instrument cluster as previously described

in this section.

2.
Remove clock set shaft knob.

3.
Remove eight screws securing cluster housing to

bezel trim panel. Separate parts carefully observing

stack up of parts.

4.
Remove two screws securing speedometer head to

rear of cluster housing.

NOTE:
Servicing of the speedometer head

should be performed by an authorized AC Speed-

ometer Service Station.

5. To install, reverse the removal procedure..

SPEEDOMETER CABLE

Replacement or Lubricatibn

1.
Disconnect the speedometer cable from the speed-

ometer head. Remove the old cable by pulling it out

from speedometer end of conduit.

NOTE:
If old cable is broken it may be neces-

sary to remove lower piece from transmission

end of conduit.

2.
Lubricate the lower 3/4 of cable with speedometer

cable lubricant and push the cable into the conduit.

Connect the upper end to the speedometer head and

road test vehicle for proper speedometer operation.

INDICATOR LIGHT REPLACEMENT

To replace any indicator or cluster bulb, unsnap the

proper socket from rear of instrument cluster, remove

and replace bulb, and reinsert unit into rear of cluster

housing.

OIL PRESSURE INDICATOR

If the light does not come on when the ignition switch
is turned on, or if the light comes on and remains on

after the engine is started, one or more of the following

conditions is indicated:

• Low oil pressure

• High engine temperature

• Defective wiring or switch

Switch Replacement

1.
Disconnect wiring harness connector from sender

unit terminal (located in block above starter on

L-6 engines and at left front of distributor on V-8

engines).

2.
Remove sender unit, replace with new unit, and

; check operation.

GENERATOR INDICATOR

1.
Ignition on, engine not running and telltale light off.

a. Indicator bulb burned out, replace bulb.

b.
Open circuit or loose connection in the telltale

light circuit.

2.
Telltale light stays on after engine is started.

a. If indicator light does not go out at engine idle

speed, refer to Charging Systems under Engine

Electrical, Section 6Y.

TEMPERATURE (COOLING SYSTEM) INDICATOR

The temperature indicator circuit consists of two re-

motely located units, indicator gauge and engine sender

unit. The indicator gauge on all models uses a single

red light to indicate an overheated engine condition.

Engine Sender Unit Replacement

1.
Drain engine cooling system to a level below unit.

2.
Remove sender unit (located in the inlet manifold

near water pump housing on V-8 engines and in the

cylinder head near an exhaust port on L-6 engines)

and replace with new unit.

3.
Refill cooling system and check operation of unit.

CORVETTE INSTRUMENTS AND GAUGES

INDEX

Page

General Description ., 12-34

Service Operations . 12-35

Instrument Cluster ., 12-35

Fuel Gauge 12-35
Speedometer/Tachometer Service. 12-35

Temperature Gauge 12-35

Ammeter/Oil Pressure Gauges 12-35

GENERAL DESCRIPTION

All Corvette instruments and gauges are conveniently

located in the dash-mounted cluster. The entire cluster

is removable to permit servicing of the various instru-

ments and gauges. The indicator and cluster illuminating

bulbs may be replaced without removing the cluster from

the panel.
Regular maintenance is not required on the instrument

cluster or its components other than maintaining clean

and keeping the speedometer and tachometer cables

properly lubricated.

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-35

SERVICE OPERATIONS

INSTRUMENT CLUSTER

REMOVAL AND INSTALLATION (Fig. 49)

1.
Remove mast jacket assembly. Refer to Section 9

for removal procedures.

2.
Disconnect tachometer drive cable at distributor.

3.
Disconnect the headlamp panel control switch from

instrument cluster.

4.
Remove lighting switch as outlined in this section.

10 10-A 1112 13

14
15 16 17 18 19

Fig.
49- Instrument Cluster Connections

1.
Cluster Illuminating

Bulbs

2.
Direction Signal Indicator

Bulb L.H.

3. Direction Signal Indicator

BulbR.H.

4.
Headlamp Actuating Motor

Indicator

5. Headlamp Hi Beam

Indicator

6. Parking Brake Alarm

Indicator

7. Ground Lead Attaching

Point

8. Temperature Indicator
"1"

Terminal
9.

10.

10A.

11.

12.

13.

14.

]5.

16.

17.

18.

19.

20.

21.
Temperature Indicator "S"

Terminal

Ignition Switch Receptacle

ignition Switch Illuminating

Bulb

Oil Pressure Indicator

Tachometer

Lighter Receptacle

Trip Odometer

Wiper Switch Receptacle

Speedometer

Ammeter "Gen" Terminal

Ammeter "Battery" Terminal

Lighting Switch Receptacle

Fuel Gauge
"1"
Terminal

Fuel Gauge "S" Terminal

5. Remove the ignition switch. Refer to Section 6Y

for removal procedure. Then disconnect ignition

switch lamp support at instrument panel.

6. Disconnect oil pressure line at oil pressure gauge

then remove the lead wires from ammeter, wiper

switch and cigarette lighter. Disconnect trip odom-

eter at mast jacket support.

7. Remove the instrument cluster-to-dash retaining

screws and pull cluster assembly slightly forward

to obtain clearance for removal of speedometer

cable, tachometer cable, cluster ground wire, fuel

gauge lead wires and remaining indicator and cluster

illuminating lamps.

8. To install cluster in dash panel, reverse removal

procedure.

FUEL GAUGE

The gasoline fuel gauge circuit consists of an electri-
cal indicator in the instrument cluster and a float-

controlled rheostat in the fuel tank.

Since the fuel gauge consists of two remotely located

units and connecting wires, it is sometimes difficult to

determine which unit is at fault when the gauge fails to

operate properly. Cluster removal is necessary to re-

place the fuel gauge.

NOTE:
Be sure to check gas gauge fuse in fuse

panel before attempting to trouble shoot for

inoperative gauge or tank sending unit.

SPEEDOMETER AND/OR TACHOMETER

Removal and Installation

Cluster must be removed from vehicle to service

speedometer head assembly (see Cluster Removal pro-

cedure)
.
With cluster removed from vehicle:

1.
Remove five screws securing cluster back panel to

cluster assembly; separate the parts carefully.

CAUTION: Care must be used to avoid marring

instrument cluster face.

2.
Remove two screws securing speedometer or ta-

chometer head to cluster back panel; carefully re-

move speedometer or tachometer head.

NOTE:
Servicing of speedometer or tachom-

eter head should be performed by an authorized

AC service station.

3.
Reverse above procedure to install speedometer.

Cable Replacement or Lubrication

1.
Disconnect the. cable from the speedometer or ta-

chometer head. Remove the old cable by pulling it

out from speedometer end of conduit.

NOTE:
If old cable is broken it may be nec-

essary to remove lower piece from transmission

or distributor end of conduit as applicable.

2.
Lubricate the lower 3/4 of cable with
AC
speedom-

eter cable lubricant and push the cable into the con-

duit. Connect the upper end to the speedometer or

tachometer head and road test vehicle for proper

operation.

TEMPERATURE GAUGE

The temperature indicator requires very little service

other than testing for malfunctioning and replacing de-

fective units. Cluster must be removed to service tem-

perature gauge.

Do not attempt to repair either the engine unit or the

gauge. When installing new engine unit, do not use

thread compound on unit threads, as this will increase

electrical resistance of unit and cause faulty reading

on gauge.

AMMETER OR OIL PRESSURE GAUGE

The ammeter or oil pressure gauge requires very

little attention other than keeping ammeter terminals

clean and tight. If the oil pressure control line should

become restricted it should be blown out or replaced.

Cluster must be removed to service these gauges.

HftVKI MANUAL

ELECTRICAL-BODY
AND
CHASSIS
12-36

CAMARO INSTRUMENTS AND GAUGES

INDEX

Page

General Description
12-36

Service Operations
12-36

Instrument Cluster
. . . 12-36

Instrument Lamps
12-36

Printed Circuit
12-36

Fuel Gauge
12-37

Tachometer
. . 12-37

Seat Separator Instrument Console
12-37
Page

Fuel Gauge
12-37

Ammeter
12-37

Temperature Gauge
12-37

Oil Pressure Gauge
. 12-37

Fuel Warning Unit
12-37

Clock.
... 12-37

Oil Pressure Indicator
12-37

Generator Indicator
12-38

Temperature Indicator
12-38

GENERAL DESCRIPTION

The standard Camaro instrument cluster assembly con-

sists
of two
circular units which house
the
speedometer

and fuel gauge assemblies.
The oil
pressure, left-hand

directional
and
brake warning indicators
are
located
in

the face
of the
speedometer bezel while generator,
tem-

perature
and
right-hand directional indicators are grouped

with
the
fuel gauge unit.
The
high beam indicator
is

located between
the
cluster bezels.

A special instrumentation package
is
available with
the

eight-cylinder engine
and
center floor console combina-

tion.
The
special cluster includes:
a
clock; coolant

temperature,
oil
pressure, fuel
and
ammeter gauges,

mounted forward
on the
seat separator console;
a ta-

chometer
in the
right circular housing
of the
dash
in-

strument cluster; and
a low
fuel level indicator replacing

the
oil
pressure indicator lamp
in the
instrument cluster.

The instruments
and
gauges,
may be
serviced only

after
the
instrument cluster
is
removed from
the
vehicle.

Indicator
and
cluster lamps except
for the
high beam

indicator
may be
replaced without removing
the
cluster

assembly. Partial cluster removal
is
necessary when

replacing
the
high beam indicator due
to its
proximity
to
the upper brace
rod
anchor plate.
The
bulbs
are in-

stalled
in
plastic sockets which lock into
the
cluster

housing and make contact with
the
printed circuit.

A
low
level fuel warning system
is a
special feature

available with
the
floor console gauge pack. This
sys-

tem includes
an
indicator lamp
in the
dash cluster and
a

semi-conductor unit senses
the
change
in
electrical
re-

sistance
of the
fuel system circuitry
as
variations
in

fuel level occur.
The
sensing device
is
replaced
as a

unit
if
found defective.

The brake warning light serves
a
dual purpose.
It

functions
as an
indicator when
the
parking brake
is ap-

plied
and
also
if
there
is a
malfunction (loss
of
hydraulic

pressure)
in the
brake system. Switches which provide

the signal
to
operate
the
light
are
located
at the
parking

brake assembly
and at the
brake master cylinder
in the

hydraulic lines. Service
of the
brake pressure differ-

ential switch unit
is
covered
in
Section
5 of
this manual.

Regular maintenance
is not
required on
the
instrument

cluster
or its
components other than maintaining clean,

tight electrical connections, replacing defective parts

and keeping
the
speedometer properly lubricated.

SERVICE OPERATIONS

INSTRUMENT CLUSTER (Figs.
50
thru
53)

Removal
and
Installation

1.
Disconnect battery ground cable.

2.
Remove mast jacket lower support screws
at toe
pan.

3.
Remove mast jacket upper support bolts
and
allow

steering wheel
to
rest
on
seat cushion.

CAUTION: Both supports must
be
detached
to

prevent distortion
of
mast jacket.

4.
Remove cluster attaching screws from face
of
panel

and partially remove assembly from console opening.

5. Reaching behind cluster assembly, disconnect speed-

ometer cable, speed warning device
(if so
equipped
-

Fig.
51) and
chassis harness connector
at
rear
of

panel.

6. Remove assembly from console opening to
a
suitable

bench area
for
required service operations.

7.
To
install, reverse removal procedure.

INSTRUMENT CLUSTER LAMP REPLACEMENT

1.
Turn bulb holder counterclockwise
and
pull
out to

remove from
the
cluster housing.
2.
Pull bulb straight out
to
remove from socket.

3.
Press replacement bulb inward
to
lock
in
socket.

4.
Insert lamp assembly into housing, with lugs
on

holder entering notches
in
housing,
and
turn clock-

wise
to
lock
in
place.

PRINTED CIRCUIT REPLACEMENT

1.
Remove instrument cluster
as
previously described

in this section.

2.
Remove
all
cluster illuminating and indicator lamps

from housing.

3.
Remove fuel gauge terminal nuts
or
tachometer
re-

taining nuts securing printed circuit
to
housing.

4.
Remove four
hex
head screws retaining printed
cir-

cuit
to the
cluster housing
and
remove circuit from

housing.

5.
To
install, reverse removal procedure.

CAUTION:
The
retaining screws
are
part
of

the grounding circuit
and
must
be
installed
to

provide proper connections
for the
printed
eir-

cuit.

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-37

Fig.
50 - Instrument Cluster Installation — Camaro

FUEL GAUGE REPLACEMENT

1.
Remove instrument cluster assembly as previously

described.

2.
Remove cluster lamps from gauge cover plate,

ground screw and terminal nuts attaching printed

circuit to fuel gauge.

3.
Remove three screws retaining gauge assembly to

cluster housing.

4.
Carefully move printed circuit away from gauge and

remove gauge assembly from cluster housing.

5. Remove terminal nuts securing gauge to cover plate,

and detach gauge unit.

6. To install, reverse removal procedure.

TACHOMETER

NOTE:
The tachometer is a self-contained, all

transistor unit requiring very little service

other than keeping the terminal nuts clean and

tight. The unit is not serviceable and must be

replaced, if defective.

1.
Remove instrument cluster as previously described

in this section.

2.
Remove cluster lamps from rear of gauge cover and

disconnect harness wiring connections from gauge

terminals.

3.
Remove three screws retaining gauge to cluster

housing.

4.
Move printed circuit away from gauge area and re-

move gauge unit from housing.

5. Remove terminal nuts securing gauge to cover

detach unit.

6. To install, reverse removal procedure.

SEAT SEPARATOR INSTRUMENT CONSOLE

(Fig.
54)
(Fuel,
Ammeter, Temperature, Oil Pressure Gauges,

Low Fuel Warning Unit, and Clock)

1.
Disconnect battery ground cable.

2.
Remove clock shaft knob from face of cluster.

3.
Remove cover retaining screws (4) and cover from

cluster assembly.

NOTE:
Use an alien wrench to remove the two

screws located in the top of the cover below the

instrument console.

4.
Remove four screws retaining gauge mounting plate

to cluster housing.

5. Carefully disengage gauge plate from housing and

disconnect oil pipe and all electrical connections at

rear of gauges.

NOTE:
At this point, with gauge package re-

moval from housing all gauges including the low

fuel warning system may easily be serviced.

6. To install assembly, use reverse of removal

procedure.

OIL PRESSURE INDICATOR

If the light does not come on when the ignition switch

is turned on, or if the light comes on and remains on

after the engine is started, one or more of the following

conditions is indicated.

• Low oil pressure

• Defective wiring or switch

Sending Unit Replacement

1.
Disconnect wiring harness connector from sender

unit terminal (located in block above starter on L-6

engines and at left front of distributor on V-8

engines).

Fig.
51 - Speed Warning Device

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-38

Fig.
52 - Instrument Cluster Lighting

1
• Cluster Lamp

2.
* High Beam Indicator

3. Oil Pressure Indicator

4.
L.H. Directional Indicator

5. Generator indicator
6. R.H. Directional indicator

7. Temperature Indicator

8. Printed Circuit

9. Chassis Harness Connector

10,
Brake Warning Indicator

2.
Remove sender unit.

3.
Replace with new unit and check operation.

GENERATOR INDICATOR

1.
Ignition on, engine not running and indicator light off:

•Indicator bulb is burned out, replace bulb.

•Open circuit or loose connection in the indicator

light circuit.
2.
Indicator light stays on after engine is started:

•Ti indicator light does not go out at engine idle

speed, refer to Charging System Tests in Section

6Y, Engine Electrical.

TEMPERATURE (COOLING SYSTEM) INDICATOR

The temperature indicator circuit consists of two re-

motely located units, indicator lamp and sending unit.

The "indicator lamp, located in the instrument cluster

CHfVROtEr CHASM SfXVICf

ELECTRICAL-BODY
AND
CHASSIS
12-56

DEPRESSED PARK 2-SPEED WIPER
AND
WASHER

CORVETTE

GENERAL DESCRIPTION

The 2-speed windshield wiper
(fig. 91)
consists
of a

compound wound
12
volt dc motor and
a
gear box section

containing
the
gear mechanism
and
relay control.
The

motor armature
is
fitted with
a
worm gear which drives

the main gear assembly and crank arm.

The relay control, consisting
of a
relay coil, relay
armature
and
switch assembly,
is
located in the gear
box"

section and controls the starting and stopping of the wiper

through
a
latching mechanism (fig. 92).

An electric .washer pump
is
mounted
on the
gear box

section
of the
wiper
and is
driven by the wiper unit gear

assembly (fig. 93).

SERVICE OPERATIONS

WIPER MOTOR
AND
WASHER

PUMP ASSEMBLY

REMOVAL AND INSTALLATION

1.
Raise vehicle hood
and
disconnect, ground lead
at

battery.

2.
Remove engine distributor shielding
and
left bank

spark plug wire vertical shield.

3.
Disconnect left bank spark plug wire bracket-to-

manifold and position assembly to one side.

4.
Disconnect ignition resistor at firewall, then remove

washer pump inlet
and
outlet hose
at
pump valve

assembly.

5.
Remove engine distributor
cap
and position
to one

side;
then disconnect washer pump
and
motor
as-

sembly lead wires.

6. Remove glove
box
door
and
compartment. Refer
to

Section
1
for
removal procedure.

7.
Make sure wiper arms
and
wiper motor are both
in

the parked position; then remove
the
wiper trans-

mission retaining clip and disconnect both transmis-

sion and spacer from crank arm (fig. 93).

8. Remove four wiper motor-to-dash wall mounting

bolts and remove wiper motor from vehicle.

9. With
the aid of
an assistant position the wiper motor

to
the
dash wall
and
install the four motor mounting

bolts,
making sure motor assembly
is in
parked

position.

GEAR

BOX

SECTION
—<

MOUNTING
^*^

GROMMET

MOTOR
_/

SECTION
MOUNTING

/"""GROMMET

ARMATURE
END
PLAY

ADJUSTING SCREW

AND LOCK
NUT

P
^
CRANK

^_ /GROMMETS
RELAY

Fig.
92 -
Relay Control

10.
Position left transmission assembly, spacer
and

right transmission assembly
on
crank arm, then in-

stall
the
retaining clip
in the
groove
in
the crank

arm.

11.
Install glove compartment and door assembly. Refer

to Section
1
for
installation procedure.

12.
Install washer pump and motor assembly lead wires;

then install engine-distributor cap.

13.
Install washer pump inlet
and
outlet hose
to
pump

valve assembly, then install ignition resistor
to

firewall.

14.
Connect left bank spark plug wire bracket-to-mani-

fold, vertical shield and engine distributor shielding.

ROTOR
CAM. ^

CAM SLOT-~-*"'-*

WASHER PUMP^.

DRIVE
PIN
m

M
VALVE

— ASSEMBLY

i

Fig.
91 - Wiper Assembly—Corvette
Fig.
93 - Washer Pump

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-60

....
£
VALVE ASSEMBLY

mm

BROWN
*yr

RED '
WATER

INTAKE

PORT

|f|i

Wjjm WATER

|HP DISCHARGE

W PORTS

WASHER

PUMP

ASSEMBLY

Fig.
102 - Washer Pump Assembly

5. Remove gear mechanism from the gear box and slide

spacer washer (No. 9) off the gear assembly eccen-

tric shaft.

6. Slide the drive plate and shaft assembly (No.. 11) out

of the gear, assembly, remove the lock and drive

pawls (Nos. 12 and 13) and remove the coil spring

(No.
14).

Reassembly

1.
Assemble lock and drive pawls to the shaft and drive

plate assembly as shown in Figure 99.

2.
Install the assembled parts from Step 1 in the gear

and eccentric shaft as shown in Figure 100.

3.
Connect the coil tension spring between the lock and

drive pawls (fig. 100).
4.
Reinstall spacer washer on the eccentric shaft of the

gear.

5. Reinstall gear mechanism in the housing as shown in

Figure 101.

6. Reassemble the parts removed in Steps 1 through 4

under drive gear disassembly.

The washer pump and/or valve assembly (fig. 102) may

be removed from the wiper assembly as a unit; therefore

it is- not necessary to remove the. wiper assembly from

the vehicle if only the washer pump and/or valve assem-

bly requires service.

WASHER PUMP SECTION

PUMP REPLACEMENT

. To replace the washer pump assembly proceed as

follows:

1.
Raise vehicle hood and remove engine distributor

shielding and distributor cap.

2.
Remove lead wires from washer pump and disconnect

ground wire from screw retained connector; discon-

nect hoses from valve unit.

3.
Remove four screws which secure the washer pump

assembly to the gear box.

a* The water inlet and outlet valve assembly is

serviced as a unit if required; also the rotor cam

is serviced separately.

4.
Install washer pump and cover assembly so that the

slot in the washer pump cam fits over the pin on the

wiper unit drive plate.

5. Install the four washer pump to gear box retaining

screws, position ground lug under lower screw.

6. Connect valve inlet and outlet hoses, attach ground

lead and washer pump lead wires.

7. Install engine distributor cap and shielding.

8. Lower hood and check operation of wiper unit.

SPECIAL TOOLS

J-21932

BEZEL NUT REMOVER

Fig.
103 - Special Tools

CHEVROLET CHASSIS SERVICE MANUAL

driven disk is sandwiched between the magnetic disk and

a field plate. The field plate forms a returning path for

the magnetic field from the magnetic disk.

The gear drive for the magnetic disk is a 90 degree

nylon gear drive with the driven gear rotating both the

magnetic disK and the speedometer drive cable.

Vacuum Switch, Air Bleed and Filter, and Low

Limit Speed Switch

The end of the shaft from the speed sensing assembly

with the rubber drum extends into the air bleed metering

assembly. This rubber drum has a tang extending from

its surface which allows a set of points to close at a

specific car speed. When the car reaches about 20 mph,

the rubber drum has rotated far enough (moved by the

brass driven disk in the magnetic field) so that its tang

has allowed a spring loaded electrical point to contact

another point. These points are in series with the sole-

noid coil so that under 20 mph, no Regulator operation

is possible.

Surrounding the rubber drum is a "U" shaped spring

clip which is held spread away from the drum by the

nose or cam of the solenoid when the solenoid is in the

relaxed position. The rubber drum and this clip com-

prise the speed clutch of the regulator. When the sole-

noid is energized, the solenoid nose moves toward the

drum and releases the ends of the clip. The clip springs

inward and attaches itself by friction to the drum. Now,
ACCESSORIES 15-5

any change in car speed will rotate the drum and move

the "U" clip just as a speedometer moves its needle.

The top of the MUtf clip is attached to the air bleed valve.

The clip moves a sleeve which slides on the orifice

tube thereby covering and uncovering air ports in the

wall of the tube (the tube inner end is plugged) whenever

car speed changes from the speed at which the solenoid

was energized. The direction of drum rotation is such

that resulting bleed valve operation will cause the Servo

to decrease engine power if the car exceeds the preset

speed and increase engine power if car speed decreases.

The air which passes out the orifice tube enters the

Regulator through the openings in the solenoid housing,

passes through the oil wetted polyurethane filter, and then

enters the orifice tube ports.

When the solenoid is de-energized, the nose retracts

and cams the ends of the "U" clip outward so that it re-

leases the rubber drum.

The solenoid also operates a vacuum switch simul-

taneously with the clutching and declutching of the "U"

clip.
The vacuum switch supplies the Servo unit with

manifold vacuum. The solenoid operated vacuum valve

slides over two ports in the Regulator wall. One port

is connected to manifold vacuum and the other is con-

nected to the center port of the Servo unit. When the

solenoid is de-energized, the valve closes the manifold

vacuum port and opens the Servo port to the inside of

the regulator case. When the solenoid is energized, the

valve connects the Servo port to the manifold vacuum

AAAGNET

SPEED CUP

FIELD PLATE

HAIRSPRING
TO SPEEDOMETER

MAGNET HOUSING

ASSEMBLY
ORIFICE TUBE &

CONNECTOR ASSEM.
CONTROL

VALVE

CLUTCH

SPRING

LOW LIMIT

SPEED SWITCH

RUBBER

DRUM

VACUUM PORT

TO SERVO

INPUT CONNECTION

SOLENOID COIL

SOLENOID AND CLUTCH

HOUSING ASSEMBLY
VACUUM PORT

TO ENGINE

VACUUM VALVE

UNLOCKING CAM

•SOLENOID PLUNGER

AIR FILTER

SIDE VIEW SECTION

REGULATOR DISENGAGED
END VIEW SECTION

ENGAGED

Fig.
8 - Regulator-Cross Section '

CHEVROLET CHASSIS SERVICE MANUAL