1967 CHEVROLET CAMARO brake

ENGINE FUEL 6M-4

Fig.
3C-Fuel Level Sight Plug

2.
Push hand choke knob in to within 1/8" of instru-

ment panel.

3.
Loosen choke cable clamp at carburetor bracket and

adjust cable through the clip until the choke valve

is wide open.

4.
Tighten cable clamp at carburetor bracket and check

operation of choke valve to ensure full closed and

wide open positions.

5. Install air cleaner.

Float Adjustment

Ho/fey (Model 4150
Center
Inlet & Model 2300)

1.
Remove air cleaner then remove the fuel level sight

plugs (Fig. 3c)

2.
With parking brake on, and transmission in neutral,

start the engine and allow it to idle.

3.
With the car on a level surface, the fuel level should

be on a level with the threads at the bottom of the

sight plug port (plus or minus 1/32 inch).

NOTE:
No float drop adjustment is required

on this carburetor.

4.
If necessary to adjust (either or both bowls), loosen

inlet needle lock screw and turn the adjusting nut

clockwise to lower or counter-clockwise to raise

fuel level, then tighten lock screw.

NOTE:
1/6 turn of adjusting nut equals ap-

proximately 1/16" fuel level change.

5. Allow a minute for fuel level to stabilize then re-

check the level at sight plug.

6. Readjust, if necessary, until proper level is obtained,

then install sight plug and air cleaner.

NOTE:
To assure proper secondary float level

setting it is advisable to accelerate primary

throttles slightly and hand operate secondary
throttle. This assures a stabilized secondary

fuel level.

Additional Adjustments

The following adjustments may be made without re-

moving the carburetor from the engine. For procedure

refer to Section 6M of the Overhaul Manual under the

carburetor being serviced.

Rochester BV

• Float

• Idle Vent

• Choke Rod (Fast Idle)

• Choke Vacuum Break

• Choke Unloader

Rochester 2GV

• Float

• Accelerator Pump

• Idle Vent

• Choke Rod (Fast Idle)

• Choke Vacuum Break

• Choke Unloader

• Secondary Throttle Opening

• Secondary Throttle Lockout

Rochester 4MV

• Float

• Accelerator Pumj)

• Idle Vent

• Air Valve

• Choke Rod

• Choke Vacuum Break

• Choke Unloader

• Air Valve Lockout

• Secondary Opening

• Secondary Lockout

Carter YF

• Float

• Idle Vent

• Choke Rod (Fast Idle)

• Choke Vacuum Break

• Choke Unloader

Holley 4160 and 4150
(Except End
Inlet)

• Float

• Air Vent Valve

• Accelerator Pump

• Choke Vacuum Break

• Choke Unloader

Holley 2300 and 4150
(End
Inlet)

• Air Vent Valve (except 2300)

• Accelerator Pump

• Choke Vacuum Break

• Choke Unloader

Removal

Flooding, stumble on acceleration and other perform-

mance complaints are, in many instances, caused by the

presence of dirt, water, or other foreign matter in the

carburetor. To aid in diagnosing the cause of the com-

plaint, the carburetor should be carefully removed from

the engine without draining the fuel from the bowl.

The contents of the fuel bowl may then be examined for

contamination as the carburetor is disassembled.

1.
Remove air cleaner and gasket.

2.
Disconnect fuel and vacuum lines from carburetor.

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE-ELECTRICAL 6Y-10

circuit. Make absolutely certain all connections in

the circuit are secure.

5.
Do not short across or ground any of the terminals

on the generator or regulator.

6. Do not attempt to polarize the generator.

7.
Do not disconnect lead at generator without first dis-

connecting battery ground cable.

Trouble in the A.C. charging system will usually be

indicated by one or more of the following conditions:

1.
Faulty indicator lamp or ammeter operation.

2.
An undercharged battery (usually evidenced by slow

cranking speeds).

3.
An overcharged battery (usually evidenced by exces-

sive battery water usage).

4.
Excessive generator noise or vibration.

Described below are a series of on-the-vehicle quick

checks which are designed to assist the service tech-

nician in locating troubles within the various components

of the engine electrical system. Additional checks, ad-

justments and overhaul procedures of these components

are also described in the "Charging Systems—Service

Operations Section" and should be referred to as

necessary.

STATIC CHECKS

Before making any electrical checks, perform the fol-

lowing static checks:

1.
Check for loose fan belt.

2.
Check for defective battery. (Refer to Battery).

3.
Inspect all connections, including the slip-on con-

nectors at the regulator and Delcotron.

NOTE: Do not short field to ground to check if

generator is charging since this will seriously

damage the charging system.

SYSTEM CONDITION TEST

This test is used .to indicate the overall condition of the

charging system (both good and defective) and to isolate

the malfunctioning unit if the system is defective.

NOTE: On Corvette models difficulty may be

encountered -when attempting to make the re-
quired test connections at the voltage regulator.

It is advisable to remove the regulator from its

mounting location to perform the necessary con-

nections at the regulator for the following tests

but make sure unit is grounded.

1.
With ignition off, perform the prescribed Static

Checks outlined in this section. Then set hand brake

and shift transmission
into
neutral.

2.
Connect a voltmeter from junction block relay to

ground at regulator base.

CAUTION: Be sure meter clip does not touch a

resistor or terminal extension under regulator,

3.
Connect a tachometer on engine.

4.
Models equipped with Indicator Lamp: Turn ignition

switch on "ON" position and check indicator lamp.

If lamp fails to glow, perform appropriate tests and

corrections (Indicator Lamp Circuit Tests) before

continuing.

Models equipped with Ammeter: Turn ignition

switch to "ACC" with an accessory on and check

ammeter. If ammeter fails to read discharge, check

ammeter circuit before continuing.

5.
Models equipped with Indicator Lamp: If lamp glows,

start the engine and run' it at 1500 rpm or above.

Check indicator lamp. If lamp fails to go out, per-

form appropriate test and corrections (Indicator

Lamp Circuit Test) before continuing.

Models equipped with Ammeter: If ammeter reads

discharge, start the engine and observe ammeter. If

meter fails to move toward charge (from original

position), perform appropriate test and corrections

(Field Circuit Tests) before continuing.

NOTE: At this point a field circuit has been

established and any other problem will lie in

generator or regulator.

6. Turn on high-beam headlights and heater blower

motor to high speed, run engine at or above 1500

rpm (for a few minutes, if necessary) and read the

voltage on meter.

AIR GAP

ADJUSTING NUT

ONLY

ADJUSTING SCREW

(Turn To Adjust

Voltage Setting)

Fig.
6c—Adjusting Voltage Setting

CHEVROLET CHASSIS SERVICE MANUAL

CLUTCH AND TRANSMISSIONS 7-4

5.
Install Tool J-5824 to support the clutch assembly

during removal.

NOTE: Look for "X" mark on flywheel and on

clutch cover. If MX" mark is not evident, prick

punch marks on flywheel and clutch cover for

indexing purposes during installation.

6. Loosen the clutch-to-flywheel attaching bolts evenly

1 turn at a time until spring pressure is released,

then remove the bolts, and remove clutch assembly.

Installation to Vehicle

Clean pressure plate and flywheel face. (They should

be free of oil, grease, metal deposits or burned spots).

1.
Position the clutch disc and pressure plate in relar

tive installed position and support them with align-

ment Tool J-5824.

NOTE: The driven disc on the 4 and 6 cylinder

engines is installed with the damfper springs to

the flywheel side; the V-8 is opposite, however,

THE GREASE SLINGER IS ALWAYS ON THE

TRANSMISSION SIDE.

2.
Turn clutch assembly until "X" mark on cover lines

up with "X" mark oh flywheel, then align cover bolt

holes to nearest flywheel holes.

3.
Install a bolt in every hole and tighten down evenly

and gradually until tight (to avoid possible clutch

distortion).

NOTE: Cover loads are as high as 1-1/4 tons.

4.
Remove pilot tool.

5.
Unhook clutch fork and lubricate ball socket and fork

fingers at release bearing end with a high melting

point grease such as graphite and reinstall fork on

ball stud. On Corvette models use Moly Grease.

6. Lubricate the recess on the inside of throwout bear-

ing collar and the throwout fork groove with a light

coat of graphite grease (fig. 4). On Corvette models

use Moly Grease.

7.
Install clutch fork and dust boot into clutch housing

and install throwout bearing to the throwout fork, then

install flywheel housing.

8. Install transmission as outlined in transmission

section.

9. Connect fork push rod and spring.

10.
Adjust shift linkage as outlined in transmission

section.

11.
Perform linkage adjustment for pedal free play and

check clutch release position.

CLUTCH PEDAL

The clutch pedal is the pendant-type hung from a sup-
Fig. 5 - Release Bearing Lubrication and Comparison

port brace common to the brake pedal and must be re-

moved to remove brake pedal. Refer to Section 5 for

brake and clutch pedal service procedure.

CLUTCH CROSS SHAFT (Figs. 6, 7 & 8)

Removal

1.
Remove linkage return and lower linkage springs and

disconnect clutch pedal and fork push rods from re-

spective cross shaft levers.

2.
Loosen outboard ball stud nut and slide stud out of

bracket slot.

3.
Move cross shaft outboard, and as required to clear

inboard ball stud, then merely lift out to remove

from vehicle.

Repairs

The cross shaft has nylon ball stud seats which should

be inspected for wear or damage. Also check condition

of engine bracket ball stud assembly and special anti-

rattle "O" ring. Figures 6, .7
&
8 show component parts

of cross shaft. Replace parts as necessary based on wear

or damage. Lubricate ball studs and seats with graphite

grease before reassembly.

Installation

1.
Reverse removal procedure to install.

2.
Adjust clutch linkage as previously outlined.

CHEVROLET CHASSIS SERVICE MANUAL

CLUTCH AND TRANSMISSIONS 7-9

6. Connect speedometer cable.

7. Install propeller shaft assembly.

8. Fill transmission with lubricant specified in Section

O.

CORVETTE TRANSMISSION REPLACEMENT

, 1. Disconnect battery ground cable.

2.
Pisassemble transmission shift control lever by un-

screwing ball from lever, lifting out
"T"
handle re-

turn spring and "T" handle, then remove the anti-

rattle bushings.

3.
Raise front and rear of vehicle.

4.
Insert a block of wood between the top of the dif-

ferential carrier housing and the underbody (to pre-

vent upward travel of the carrier when the carrier

front support is disconnected).

5. Disconnect the differential carrier front supportfrom

its frame bracket, by removing the nut on the under-

side of the biscuit mount.

6. Pry the carrier downward to relieve load while re-

moving the two center mounting bolts from the car-

rier front support. (To pry carrier downward insert

crowfoot end of a pry bar through the opening in the

carrier front support, hooking end of bar over top of

the center mounting bolt pad cast in the underside of

the carrier.)

7. Pivot carrier support downward for access to prop

shaft "U" joint.

8.
.
Disconnect prop shaft front and then rear "U" bolts.

9. Disconnect parking brake cable from ball socket at

idler lever located near center of underbody.

10.
Remove prop shaft by moving shaft forward.

11.
Remove heat deflectors from the right and left ex-

haust pipe.

12.
Remove left bank exhaust pipe.

13.
Remove right bank exhaust pipe and heat riser.

14.
Disassemble the transmission mount, as follows:

a. Remove the two bolts that attach rear mount

cushion to the rear mount bracket.

b.
Support engine under oil pan and raise engine to

remove load from rear mount cushion.
CAUTION: To avoid damage to oil pan, a suit-

able wide base, heavy wood platform should be

placed between the jack pad and the oil pan.

c. Remove the three transmission mount bracket-

to-
crossm ember bolts and remove mount bracket.

d. Remove the two bolts from mount pad to trans-

mission case and remove rubber mount cushion

and exhaust pipe "yoke".

15.
Disconnect transmission linkage by removing the

shift levers at the transmission side cover.

16.
Disconnect speedo cable at transmission extension.

17.
Remove transmission output shaft slip yoke.

NOTE:
The yoke is removed to avoid tearing

the heat reflecting pad on the underbody, when

the transmission is being removed.

18.
Remove two bolts to disconnect the transmission

gearshift control lever and bracket assembly from

its adapter plate on side of transmission. Lower

transmission assembly from the vehicle, letting the

gearshift lever slide down and through the dust boot

in the console.

19.
Remove transmission-to-clutch housing attaching

bolts.

20.
Slide transmission assembly rearward from clutch

and rotate transmission for access to the three flat

head machine screws in the control lever bracket

adapter plate. Remove adapter plate. Rotate trans-

mission back to the upright position.

21.
To allow room for transmission removal slowly

lower the rear of engine until the tachometer drive

cable at the distributor just clears the horizontal

ledge across the front of dash.

CAUTION: The tachometer cable can be easily

damaged by heavy contact with the dash. Slide

transmission rearward out of the clutch, then

tip front end of transmission downward and

lower the assembly from vehicle.

22.
Reinstall transmission assembly by performing above

steps in reverse order.

TRANSMISSION OVERDRIVE

INDEX

Page

General
Description 7-10

Maintenance
and Adjustments 7—10

Governor
Switch and Pinion .............. 7-10

Sun
Gear Solenoid Oil Seal and Control

Cable
Bracket 7-10

Case
Rear Oil Seal 7-10

Removal
7-10

Installation
. . . . . 7-10

Control
Shaft Lever and Oil Seal 7-10

Speedometer
Driven Gear 7-10

Electrical
Unit Checks 7-11

Overdrive
Relay . 7-11
Page

Air
Gap 7-11

Point
Opening 7-11

Closing
Voltage 7-11

Solenoid
. 7-11

Closing
Coil 7-11

Engaging
Spring . - 7-11

Ignition
Grounding Contact . 7-11

Governor
Switch 7-11

Kickdown
Switch 7-11

Diagnosis
- Overdrive 7-12

Mechanical
. 7-12

Electrical
7-13

CHEVROLET CHASSIS SERVICE MANUAL

CLUTCH AND TRANSMISSIONS 7-31

with the "white" stripe painted on the engine

side of the flywheel outer rim, denoting the

"heavy" side of the engine.

1.
Mount transmission on transmission lifting equip-

ment installed on jack or other lifting device.

2.
Remove converter holding tool.

CAUTION: Do not permit converter to move

forward after removal of holding tool.

3.
Raise transmission into place at rear of engine and

install transmission case to engine upper mounting

bolts,
then install remainder of the mounting*bolts.

Torque bolts to 35 ft. lbs.

4.
Remove support from beneath engine, then raise

rear of transmission to final position.

5. Through flywheel cover opening align as closely as

possible the "white" flywheel balance mark stripe

and the "blue" painted stripe on the end of converter

cover and housing. If scribed during removal, align

scribe marks on flywheel and converter cover. In-

stall converter to flywheel attaching bolts. Torque

bolts to 15-20 ft. lbs.

6. Install converter under pan.

7. Reinstall transmission support crossmember to

transmission and frame.

8. Remove transmission lift equipment.

9. Connect propeller shaft to transmissions.

10.
Connect manual and TV control lever rods to

transmission.

11.
Connect oil cooler lines (if so equipped), vacuum

Fig.
13PG - Converter Holding Tool
modulato:* line, and speedometer drive cable to

transmission.

12.
Refill transmission through filler tube, using Funnel

J-4264 and following the recommended procedure

provided earlier in this section.

13.
Check transmission for proper operation and for

leakage. Check and, if necessary, adjust linkage.

CORVETTE POWERGLIDE TRANSMISSION

Replacement

1.
Disconnect battery ground cable.

2.
Remove ball end from transmission shift control

lever.

3.
Raise front and rear of vehicle.

4.
Insert a block of wood between the top of the dif-

ferential carrier housing and the underbody (to

prevent upward travel of the carrier when the car-

rier front support is disconnected).

5. Disconnect the differential carrier front support

from its frame bracket, by removing the nut on the

underside of the biscuit mount.

6. Pry the carrier downward to relieve load while re-

moving the two center mounting bolts from the

carrier front support. (To pry carrier downward

insert crowfoot end of a pry bar**hrough the open-

ing in the carrier front support, hooking end of bar

over top of the center mounting bolt pad cast in the

underside of the carrier).

7. Pivot carrier support downward for access to prop

shaft "U"-joint.

8. Disconnect prop shaft front and then rear
"U"
bolts.

9. Disconnect parking brake cable from ball socket at

idler lever located near center of underbody.

10.
Remove prop shaft by moving shaft forward.

11.
Remove left bank exhaust pipe.

12.
Remove right bank exhaust pipe and heat riser.

13.
Disassemble the transmission mount, as follows:

a. Remove the two bolts that attach rear mount

cushion to the rear mount bracket.

b.
Support engine under oil pan and raise engine to

remove load from rear mount cushion.

CAUTION: To avoid damage to oil pan, a suit-

able wide base, heavy wood platform should be

placed between the jack pad and the oil pan.

c. Remove the three transmission mount bracket-

to-crossmember bolts, then remove mount

bracket.

d. Remove the two bolts from mount pad to trans-

mission case and remove rubber mount cushion

and exhaust pipe "yoke".

14.
Disconnect oil cooler lines at transmission and

swing lines clear.

15.
Remove connector underpan.

16.
Remove converter to flywheel attaching bolts.

17.
At transmission disconnect vacuum modulator line

and speedometer cable.

18.
Disconnect transmission shift linkage from trans-

mission gearshift control lever. Remove shift lever.

19.
At transmission, remove throttle valve linkage and

disconnect neutral safety switch linkage, also re-

move the gearshift control linkage.

20.
Remove neutral safety switch from transmission

control bracket.

CHEVROLET CHASSIS SERVICE

CLUTCH AND TRANSMISSIONS 7-32

21.
Remove transmission output shaft slip yoke and in-

sert a plastic shipping plug in end of extension to

prevent spillage of transmission fluid.

NOTE:
The yoke is removed to avoid tearing

the heat reflecting pad on the underbbdy, when

the transmission is being removed.

22.
Remove bright metal ignition shielding from dis-

tributor area.

23.
Remove the transmission dip stick and tube

assembly.

24.
Disconnect transmission vacuum modulator line at

distributor advance line tee.

25.
Position transmission hoist under transmission and

attach safety chain to transmission.

26.
Remove transmission converter housing-to-engine

attaching foolts and slide transmission rearward.
NOTE:
Observe converter when moving trans-

mission rearward. If converter does not move

with the transmission, pry it free of flywheel

before proceeding.

27.
Install converter retaining strap.

28.
Lower and remove transmission from vehicle by

tilting the front down and to the right while inter-

mittently lowering the transmission to facilitate its

• removal.

29.
Reinstall transmission assembly by performing the

above steps in reverse order.

Bolt Torques

Transmission Case to Flywheel

Housing Bolts 35 ft. lbs.

Converter to Flywheel Bolts. . , . . 35 ft. lbs.

OTHER SERVICE OPERATIONS

Although certain operations, such as oil pan or gasket

replacement, valve body, governor, filler pipe "O" ring,

speedometer drive gear, case extension "0" ring and

rear oil seal, vacuum modulator, and servo cover or

gasket service may be performed from underneath the
vehicle without removing the Powerglide; their service

procedure is covered in the Passenger Overhaul Manual

and is not repeated here. Refer to the- Powerglide Sec-

tion of the Passenger Overhaul Manual for all other

service operations not covered here.

DIAGNOSIS

Proper operation of the Powerglide transmission may

be affected by a number of factors, all of which must be

considered when trouble in the unit is diagnosed.

Proper trouble diagnosis can only be accomplished

when performed in a thorough step by step procedure.

The following procedure has been devised and tested and

is recommended for all trouble diagnosis complaints and

if the service man will follow this checking procedure,

accurate and dependable diagnosis may be accomplished.

This will result in a savings of time, not only to the

service man, but to the customer as well.

WARMING UP TRANSMISSION

Before attempting to check and/or correct any com-

plaints on the Powerglide transmission it is absolutely

essential that the oil level be checked and corrected if

necessary. An oil level which is either too high or too

low can be the cause of a number of abnormal conditions

from excessive noise to slippage in all ranges.

It must be remembered that cold oil will slow up the

action of the hydraulic controls in the transmission. For

this reason a trouble or oil leak diagnosis should not be

attempted until the transmission has been warmed up by

either of the following procedures:

Shop Warm Up

1.
Connect tachometer to engine.

2.
Set parking brake tight and start engine.

3.
Place selector light in
"D"
(drive) range.

4.
Adjust carburetor idle speed adjusting screw to run

engine at approximately 750 rpm and operate in this

manner for two minutes. At the end of two minutes

of operation, the transmission will be sufficiently

warmed up for diagnosis purposes.
NOTE:
At this point, readjust the engine idle

speed to 450-475 rpm in
"D"
range.

Road Warm Up

Drive the car approximately 5 miles with frequent

starts and stops.

NOTE:
At this point, make sure the engine idle

speed is set to 450-475 rpm in
"D"
range.

CHECKING FLUID LEVEL AND CONDITION

After transmission has been warmed up, check the

fluid level with the engine idling, parking brake set and

control lever in "N" (neutral). If the fluid level is low,

add fluid to bring level up to the full mark on gauge rod,

CAUTION: If fluid level is too high, fluid may

be aerated by the planet carrier. Aerated fluid

will cause turbulence in the converter which will

result in lost power, lower stall speed and lower

pressures in control circuits. Lower fluid level

to full mark, then shut off engine to allow air

bubbles to work out of fluid.

When checking oil level, aburned smell and discolora-

tion indicate burned clutches or bands and the transmis-

sion will have to be removed.

MANUAL LINKAGE

Manual linkage adjustment and the associated neutral

safety switch are important from a safety standpoint.

The neutral safety switch should be adjusted so that the

engine will start in the Park and Neutral positions only.

With the selector lever in the Park position, the park-

ing pawl should freely engage and prevent the vehicle

CHEVROLET CHASSIS SERVICE MANUAL

CLUTCH AND TRANSMISSIONS 7-33

from rolling. The pointer on the indicator quadrant

should line up properly with the range indicators in all

ranges.

OIL LEAKS

Before attempting to correct an oil leak, the actual

source of the leak must be determined. In many cases

the source of the leak can be deceiving due to "wind flow1 f

around the engine and transmission.

The suspected area should be wiped clean of all oil

before inspecting for the source of the leak. Red dye is

used in the transmission oil at the assembly plant and

will indicate if the oil leak is from the transmission.

The use of a "black light"* to identify the oil at the

source of leak is also helpful. Comparing the oil from

the leak to that on the engine or transmission dip stick

(when viewed by black light) will determine the source

of the leak.

Oil leaks around the engine and transmission are gen-

erally carried toward the rear of the car by the air

stream. For example, a transmission "oil filter tube

to case leak" will sometimes appear as a leak at the

rear of the transmission. In determining the source of

an oil leak it is most helpful to keep the engine running.

The mating surfaces of servo cover, converter housing,

transmission case and transmission case extension

should be carefully examined for signs of leakage. The

vacuum modulator must also be checked to insure that

the diaphragm has not ruptured as this would allow trans-

mission oil to be drawn into the intake manifold. Us-

ually, the exhaust will be excessively smoky if the

diaphragm ruptures due to the transmission oil added to

the combustion. The transmission case extension rear

oil seal should also be checked. All test plugs should be

checked to make sure that they are tight and that there

is no sign of leakage at these points. The converter

underpan should also be removed. Any appreciable quan-

tity of oil in this area would indicate leakage at the pump

square seal ring, pump seal assembly, or pump bolt

sealing washers.

BASIC PRESSURE CHECKS

Four basic pressure checks are used for diagnosis and

operational checks for the Aluminum Powerglide trans-

mission. All checks should be made only after thoroughly

warming up the transmission.

• Wide Open Throttle Upshift Pressure.

• Idle Pressure in "Drive" Range.

• Manual "Low" Range Pressure.

• "Drive" Range Overrun (Coast) Pressure.

It is not recommended that stall tests be conducted

which would result in engine vacuum falling below 10" Hg.

Pressure gauge hose connections should be made at

the low servo apply (main line) test point (fig. 14PG).

Run the gauge line into the driving compartment by

pushing aside the mast jacket seal. The line out of the

way of the drivers feet and connect to pressure gauge

J-21867.

• Wide Open Throttle Upshift Pressure Check

Refer to the pressure check chart for upshift pressure
SERVO APPLY

PRESSURE

Fig.
14PG - Pressure Test Plug

points as indicated on the lower servo apply (main line)

gauge.

• Idle Pressure in "Drive" Range

In addition tp the oil pressure gauges, a vacuum gauge

is needed for this check.

With the parking brake applied and the shift selector

lever in "Drive", low servo apply (main line) pressure

should be as shown on the pressure check chart.

If pressures are not within these ranges, the following

items should be checked for oil circuit leakage:

1.
Pressure regulator valve stuck.

2.
Vacuum modulator valve stuck.

3.
Hydraulic modulator valve stuck.

4.
Leak at low servo piston ring (between ring and

bore).

5.
Leak at low servo piston rod (between rod and bore).

6. Leak at valve body to case gasket.

7.
Leak at valve body gaskets.

8. Front pump clearances.

9. Check passages in transmission case for porosity.

• Manual "Low" Range Pressure Check

Connect a tachometer, apply the parking brake, place

the selector lever in "Low" range, and adjust the engine

speed to 1000 rpm with the car stationary.

Low servo apply (main line) pressure should be as

shown on the pressure check chart.

Pressures not within this range can indicate the fol-

lowing possibilities:

1.
Partially plugged oil suction screen.

2.
Broken or damaged ring low servo.

CHEVROLET CHASSIS SERVICE MANUAL

CLUTCH AND TRANSMISSIONS 7-37

LI.
- LI Range can be selected at any vehicle speed,

and the transmission will shift to second gear

and remain in second until vehicle speed is re-

duced to approximately 40 MPH, .depending on

axle ratio. LI Range position prevents the trans-

mission from shifting out of first gear.
It is very important that any communication concerning

the Turbo Hydra-Matic always contain the transmission

serial number and that all transmission parts returned

to Chevrolet Motor Division always be tagged with the

transmission serial number.

MAINTENANCE AND ADJUSTMENTS

TRANSMISSION FLUID

Transmission fluid level should be checked with trans-

mission warm and selector lever in "P" Park position,

every time engine oil level is checked or as specified in

Section 0 when engine oil is changed.

CAUTION: Since the Turbo Hydra-Matic trans-

mission is very sensitive to oil level, special

precautions should be taken when checking the

oil level, to insure against an overfifE

Transmission fluid should be changed as specified in

Section 0.

FLUID LEVEL INDICATOR

The fluid level indicator is located in the filler pipe at

the right rear corner of the engine. To bring the fluid

level from the add mark to the full mark add 1 pint.

Fluid level should be to the full mark with transmission

at normal operating temperature. With cold fluid the

level should be at the add mark or slightly below.

SHIFT CONTROL LINKAGE ADJUSTMENT

Adjust linkage as shown below and in Figure 2.

1.
The shift tube and lever assembly must be free in the

mast jacket See Section 9 for alignment of steering

column assembly if necessary.

2.
To check for proper shift linkage adjustment, lift the

transmission selector lever towards the steering

wheel. Allow the selector lever to be positioned in

drive (D) by the transmission detent.

NOTE: Do not use the indicator pointer as a

reference to position the selector lever. When

performing linkage adjustment, pointer is ad-

justed last.

3.
Release the selector lever. The lever should be in-

hibited from engaging low range unless the lever is

lifted.

4.
Lift the selector lever towards the steering wheel,

and allow the lever to be positioned in neutral (N) by

the transmission detent.

5.
Release the selector lever. The lever should now be

inhibited from engaging reverse range unless the

lever is lifted.

6. A properly adjusted linkage will prevent the selector

lever from moving beyond both the neutral detent,

and the drive detent unless the lever is lifted to pass

over the mechanical stop in the steering column.

See schematic diagram.

7.
In the event that an adjustment is required, place the

selector lever in drive (D) position as determined by

the transmission detent. See Steps 2 and 3.

8. Loosen the adjustment swivel at the cross-shaft, and
rotate the transmission lever so that it contacts the

drive stop in the steering column.

9. Tighten the swivel and recheck the adjustment. See

Steps 2 and 6. -

l(h Readjust indicator needle if necessary to agree with

the transmission detent" positions. See Section 9.

11.
Readjust neutral safety switch if necessary to pro-

vide the correct relationship to the transmission de-

tent positions. See Section 12.

12.
When properly adjusted the following conditions must

be met by manual operation of the steering column

shift lever:

a. From reverse to drive position travel, the trans-

mission detent feel must be noted and related to

indicated position on dial.

b.
When in drive and reverse positions, pull lever

rearward (towards steering wheel) and then re-

lease. It must drop back into position with no

restrictions.

NEUTRAL SAFETY SWITCH ADJUSTMENT

The neutral safety switch must be adjusted so that the

car will start in the park or neutral position, but will not

start in the other positions. For replacement refer to

Section 12 of this Manual.

DRAINING AND REFILLING TRANSMISSION

Drain oil immediately after operation before it has had

an opportunity to cool.

To drain oil proceed as follows:

1.
Remove bottom pan attaching screws, pan, and gas-

ket.

2.
Remove oil strainer. Remove "O" ring seal from

pick-up pipe and discard.

3.
Discard strainer if dirty.

4.
Install new "O" ring seal on pick-up pipe and install

strainer and pipe assembly.

5.
Thoroughly clean bottom pan.

6.. Affix new gasket to bottom pan with petroleum jelly.

7.
Install bottom pan with attaching screws and torque

to specifications;

8. If only the pan has been removed, pour approximately

7-1/2 pints of fluid into the transmission. If the

valve body has also been removed use 9-1/2 pints.

After a complete overhaul approximately 19 pints

are required. Be sure container, spout, or funnel is

clean.

9. Start engine and let idle (carburetor off fast idle

step).
Place selector lever in P position and apply

hand brake.

10.
With transmission warm (approximately 150°F), add

fluid to bring level to full mark on indicator.

CAUTION: Do not overfill. Foaming will re-

sult.

CHEVROLET CHASSIS SERVICE MANUAL