1953 JEEP DJ light

'Jeep'
UNIVERSAL
SERIES
SERVICE
MANUAL

H
11514

FIG.
H-2—WIRING
DIAGRAM—MODEL
CJ-3B
(Serial No.
35522
and
after)

1—
Left
Headlamp
2—
Left
Parking and Signal Lamp
3— Right Parking and Signal Lamp
4— Right Headlamp 5— Battery Ground Strap
6— Generator 7— Ignition
Coil

8— Junction Block
9—
Horn

10— Distributor
11— Battery
12—
Voltage
Regulator 13— Starting Motor
14—
Oil
Pressure Signal Switch 15— Temperature Sending Unit
16—
Solenoid
Switch 17— Foot Dimmer Switch
18—
Stop
Light Switch 19— Directional Signal Flasher
20— Fuse
21—
Light
Switch 22— Directional Signal Switch
23—
Horn
Button 24— Ignition and Starter Switch 25—Instrument Cluster
A—Upper Beam Indicator
B—Turn
Signal Indicator C—Instrument Lights

D—Oil
Pressure Indicator
E—Charging
Indicator F—Temperature Gauge

G—Fuel
Gauge
H—Instrument
Voltage
Regulator
25—Fuel Gauge Tank Unit
27—
Left
Tail
and
Stop
Lamp
28— Right
Tail
and
Stop
Lamp 175

H

ELECTRICAL
SYSTEM
11474

FIG.
H-3—WIRING
DIAGRAM—MODELS
CJ-5, CJ-6, DJ-5 AND DJ-6—F4
ENGINE
(Model CJ-5 after Serial No.
49248,
Model CJ-6 after Serial No.
12577)

1—
Left
Headlamp
B—Turn
Signal Indicator 17—Directional Signal Switch
2—
Left
Parking and Directional Lamp C—Instrument Lights 18—Light Switch
3— Right Parking and Directional Lamp
D—Oil
Pressure Indicator
19—Stop
Light Switch
4— Right Headlamp E—Charging Indicator 20—Foot Dimmer Switch
5— Battery Ground Cable F—Temperature Gauge 21—Directional Signal Flasher
6— Generator
G—Fuel
Gauge 22—Fuse 7— Distributor H—Instrument Voltage Regulator
23—Solenoid
Switch
8— Ignition
Coil
12—Right
Tail
and
Stop
Lamp 24—Temperature Sending Unit
9— Starting Motor 13—Left
Tail
and
Stop
Lamp 25—Oil Pressure Signal Switch
10— Voltage Regulator 14—Fuel Gauge
Tank
Unit 26—Horn
11— Instrument Cluster 15—Ignition and Starter Switch 27—Junction Block
A—Upper
Beam Indicator 16—Horn Button
whereas the Dauntless V-6
engine
Delco starter
ignition
switch. If trouble
develops
in this switch, drive is of the clutch
type.
it must be replaced.
The
ignition
switch
serves
both
to
energize
the

The
starter circuit is
opened
when the
ignition
key
ignition
system
and
also
to
engage
the starter
sole-

is allowed to return to the "Ignition On"
position.
miod switch. With the key in the vertical
position,
No repairs or adjustments can be
made
to the the electrical
system
is off. This is the
only
position
176

'Jeep*
UNIVERSAL
SERIES
SERVICE
MANUAL

H

12968
FIG.
H-4—WIRING
DIAGRAM—MODELS
CJ-5, CJ-6, DJ-5, DJ-6
LATE
F4
ENGINE

1—
Left
Headlamp
2—
Left
Parking and Signal Lamp
3— Right Parking and Signal Lamp 4— Right Headlamp
5— Generator
6— Ignition Distributor
7—
Oil
Pressure Sending Unit
8— Junction Block
9—
Horn

10— Foot Dimmer Switch 11—
Stop
Light Switch — Front
12— Temperature Sending Unit
13— Ignition
Coil

14— Starting Motor 15— Battery Ground Cable
16— Battery
17— Voltage Regulator 18—
Fuse

19— Instrument Cluster

A—Hi-Beam
Indicator

B—Auxiliary
C—Instrument
Lights

D—Oil
Pressure Indicator
E—Charging
Indicator
F—Temperature
Indicator

G—Fuel
Gauge
H—Instrument Voltage Regulator
20— Ignition and Starter Switch 21—
Flashei
(Directional Signal)
22—
Horn
Button 23— Directional Signal Switch
24— 4-Way Flasher Switch
25—
Flasher
(4-Way)
26—
Fuse

27—
Main
Light Switch 28—
Stop
Light Switch — Rear
29—
Fuel
Gauge
Tank
Unit
30—
Back-Up
Light Switch
31— Right
Tail
and
Stop
Lamp
32— Right Back-Up Lamp
33—
Left
Back-Up Lamp
34—
Left
Tail
and
Stop
Lamp

in
which the key can be removed. Turning the key
to the
left
energizes
auxiliary
equipment
such as
windshield wipers, radio, and heater. The turn
signal
lights
will
operate
with the
ignition
key in
either the
left
or right
position.
The
ignition
switch is held in
position
by a
tension
spring on the back
of the instrument panel and a
notched
bezel on
the front of the instrument panel.
H-8.
Lighting System

The
wiring for the lighting
system
is shown in the
wiring diagrams, Figs. H-2 thru H-7 of the manual,
which indicate the various units in relation to their

position
in the vehicle. The lighting circuit is pro­
tected
by an overload circuit breaker
mounted
on the rear of the light switch.
The
main light switch controls the lighting
system
177

H

ELECTRICAL
SYSTEM

14365

FIG.
H-5—WIRING
DIAGRAM—F4
ENGINE
CURRENT
MODEL
1—
Left
Headlamp

2—
Left
Parking and Signal Lamp
3—
Right
Parking and Signal Lamp

4—
Right
Headlamp
5—
Marker
Lamp
— Amber
6—
Generator
7—
Distributor

8—
Ignition
Coil

9— Starting Motor
10— Battery Ground Cable
11—
12
Volt
Battery

12—
Flasher
(Directional Signal)
13— Instrument Cluster
A—Hi-Beam
Indicator

B—Auxiliary
C—Instrument Lights
D—Oil
Pressure
Indicator
E—Charging Indicator
F—Temperature Indicator
G—Fuel
Gauge
Indicator
H—Instrument Voltage Regulator
14—
Ignition
and
Starter
Switch
15—
Horn
Button 16—
Directional
Signal Switch 17— 4-Way
Flasher
Switch
18—
Flasher
(4-Way)
19—
Windshield
Wiper Motor Switch
20—
Main
Light
Switch

21—
Fuel
Gauge
Tank
Unit

22—
Back-Up
Light
Switch
23—
Marker
Lamp — Red 24—
Right
Tail
and Stop Lamp
25—
Right
Back-Up Lamp
26—
Left
Back-Up Lamp
27—
Right
Tail
and Stop Lamp
28—
Marker
Lamp — Red 29— Stop
Light
Switch
30— Foot Dimmer Switch

31—
Windshield
Wiper Motor Assembly

32—
Voltage Regulator
33— Temperature Sending
Unit

34—
Oil
Pressure
Sending
Unit

35— Spark
Plugs
&
Cables

36—
Horn

37— Junction Block
38—
Marker
Lamp — Amber
through a
two-position
push-pull switch located on
the
left
side
of the control panel.
The
foot-operated
headlight dimmer switch is
mounted on the floorboard to the
left
of the steering
column.

H-9.
PRESTOLITE
DISTRIBUTOR
—
DAUNTLESS
V-6 and

HURRICANE
F4
ENGINE

The
Prestolite distributor on the F4
engine
is
mounted on the right
side
of the
engine
and is op­
erated by a coupling on the oil pump shaft, see Fig.
D-l,
which is driven by a spiral gear on the cam­
shaft. The spark advance is fully automatic, being controlled by built-in centrifugal
weights.
The Pres­

tolite
distributor on the V-6
engine
(Fig. H-8) is mounted at the
left
front of the
engine
on the tim­
ing chain cover. It is driven by a spiral gear on the
camshaft. The spark advance is fully automatic,
being controlled by built-in centrifugal
weights,
and by a vacuum advance system. While
some
parts of the distributor may be checked or replaced
with the unit mounted on the
engine,
it is
best
to periodically remove it for a thorough check. Infor­ mation covering the parts which can be serviced
without removal is
given
below.
The
Prestolite distributor installed on the V-6 en­

gine
is similar in construction to the distributor in­
stalled on the F4
engines
except
for the addition of

a
vacuum advance mechanism.
The
same checking procedures outlined in Par. C- 10a, are used for the Prestolite V-6 distributor with

exception
of specifications.
H-10. Distributor Cap

The
distributor cap should be inspected for cracks,
carbon runners and
evidence
of arcing. If any of

these
conditions
exists, the cap should be replaced.
Clean
any corroded high
tension
terminals.

H-11.
Rotor
Inspect the rotor for cracks or
evidence
of
excessive

burning at the end of the metal strip.
After a distributor rotor has had normal use the
end of the rotor will
become
burned. If burning is found on top of the rotor it indicates the rotor is
too short and
needs
replacing. Usually when this condition is found the distributor cap
segment
will 178

'Jeep'
UNIVERSAL
SERIES
SERVICE
MANUAL

H

12967
FIG.
H-6—WIRING
DIAGRAM—LATE
V6
ENGINE

1—Left Headlamp

2—
Left
Parking and Signal Lamp
3—
Right
Parking and Signal Lamp

4—
Right
Headlamp
5— Voltage Regulator
6—
Alternator
7—
Oil
Pressure
Sender

8— Temperature
Sender

9—
Ignition
Distributor
10— Junction Block

11—
Horn

12—
Ignition
Coil

13— Starting Motor
14— Battery Ground Cable 15— Foot Dimmer Switch 21-
16— Stop
Light
Switch — Front 22-
17— Ballast 23-
18—
Flasher
(Directional Signal) 24-
19—
Fuse
25-
20— Instrument Cluster 26-

A—Hi-Beam
Indicator 27-

B—Auxiliary
28- C—Instrument Lights 29-

D—Oil
Pressure
Indicator 30-
E—Charging Indicator 31-F—Temperature Indicator 32-
G—Fuel
Gauge
33-
H—Instrument Voltage Regulator 34-
-Ignition
and
Starter
Switch

-Horn
Button

-Directional
Signal Switch
-4-Way
Flasher
Switch

-Flasher
(4-Way)

-Fuse

-Main
Light
Switch
-Stop
Light
Switch —
Rear

-Fuel
Gauge
Tank
Unit

-Back-Up
Light
Switch

-Right
Tail
and Stop Lamp

-Right
Back-Up Lamp

-Left
Back-Up Lamp

-Left
Tail
and Stop Lamp
be burned on the horizontal
face
and the cap will

also
need
replacing. H-12. Condenser

The
condenser
prolongs
the
life
of the distributor

points
by
preventing
arcing at the
contacts.
It
also
provides
a
hotter
spark by creating a reverse
surge

of current which rapidly breaks
down
the
magnetic

field of the coil by
demagnetizing
the core. Should
the
condenser
be leaky, a weak spark will result.

Check
the
condenser
lead for broken wires or
frayed insulation. Clean and
tighten
the
connec-
179

H

ELECTRICAL
SYSTEM

ffKHs)

3—<§)

FIG.
H-7—WIRING
DIAGRAM—V6
ENGINE
CURRENT
MODEL
1—
Left
Headlamp
2—Left Parking and Signal Lamp
3— Right Parking and Signal Lamp
4—Right Headlamp 5—
Marker
Lamp — Amber
6— Alternator 7— Voltage Regulator
8— Starting Motor
9— Battery Ground Cable
10— 12 Volt Battery
11—
Flasher
(Directional Signal)
12— Instrument Cluster
A—Hi-Beam
Indicator
B—Auxiliary

C—Instrument
Lights

D—Oil
Pressure Indicator
E—Charging
Indicator

F—Temperature
Indicator

G—Fuel
Gauge Indicator
H—Instrument Voltage Regulator
13— Ignition and Starter Switch
14—
Horn
Button
15— Directional Signal Switch
16— 4-Way Flasher Switch 17—
Flasher
(4-Way)
18— Windshield Wiper Motor Switch
19—
Main
Light Switch
20—
Fuel
Gauge
Tank
Unit
21—
Back-Up
Light Switch
22—
Marker
Lamp — Red
23— Right
Tail
and
Stop
Light 24— Right Back-Up Lamp
25—
Left
Back-Up Lamp 26—
Left
Tail
and
Stop
Light
27—
Marker
Lamp — Red
28—
Stop
Light Switch
29— Foot Dimmer Switch
30— Windshield Wiper Motor Assembly
31—
Ballast
Resistor 32— Ignition
Coil

33—
Spark
Plugs and Cables 34— Temperature Sending Unit
35—
Oil
Pressure Sending Unit 36—
Horn
37— Junction Block
38—
Marker
Lamp — Amber

lions
on the terminal
posts.
Be sure
condenser
is
mounted
firmly on the distributor for a
good
ground
connection.

Should a
condenser
tester
be available the capacity for
both
F4 and Prestolite V6
condenser
should
check from .25 to .28 microfarads. In the
absence

of
tester,
check by substituting a new
condenser.

H-13. Distributor Points
a. Examine the distributor
points.
If
they
show

wear,
poor
mating, transferred metal, or pitting,

then
new
ones
should be installed. Clean the
points

with a suitable
solvent
and a stiff bristled brush.
b. Check the
alignment
of the
point
for a full,
square
contact.
If not correctly aligned, bend the
stationary
contact
bracket slightly to provide align­
ment.

c. The
contact
gap should be set at .020"
[0,508
mm.],
on the F4 and .016"
[0,406
mm.] on the
Prestolite V6. Adjustment of the gap is accom­ plished by
loosening
the lock screw and turning adjusting eccentric screw until correct gap is
secured. Be sure that the fiber block on the breaker

arm
is resting on the
highest
point
on the cam while the adjustment is
being
made. Recheck the gap
after locking the adjustment.
d. Apply a thin film of cam lubricant to the cam to
lessen
fiber block wear.
e. Using Tool C-4094, check
point
contact
spring
pressure, which should be
between
17 and 20

ounces
[0,487
a
0,567
kg.] on the F4 and 17 to 22 oz.
[0,487
a
0,624
kg.] on the Prestolite V6.

Check
with a spring scale
hooked
on the breaker

arm
at the
contact
and pull at right
angle
to the
breaker arm. Make the reading just as the
points

separate. Adjust the
point
pressure by
loosening
the stud holding the end of the
contact
arm spring
and slide the end of the spring in or out as
neces­

sary.
Retighten the stud and recheck the pressure. Too low a- pressure will
cause
engine
missing at
high
speeds.
Too high a pressure will
cause
rapid
wear of the cam, block, and
points.
180

H

ELECTRICAL
SYSTEM
FIG.
H-9—DISTRIBUTOR ASSEMBLY- HURRICANE F4 ENGINE 1—
Cap
6—Advance Plate
Lock
Screw
2—
Rotor
7—Oiler and
Felt
Wick

3—
Primary
Wire
8—Drive Shaft
4—
Breaker
Plate 9—Drive Shaft
Collar
and
Thrust
Washer 5—
Governor
Weights
attaching screws; remove vacuum advance unit
from housing.
e. Remove the two clamp
hinge
to breaker plate
screws; remove breaker plate from housing.
f. Remove the shaft assembly. To do this, file off
the upset end of the pin which is placed through
the collar and shaft at the lower end of the housing

and
drive out the pin with a suitable punch. Re­
move
the collar and washer.
Pull
the shaft from
the housing.
g. Should it be necessary to remove the cam as­
sembly, first remove the
felt
wick from the upper
end. Use
long-nose
pliers to compress and remove the spring locking clip located at the
bottom
of the

drilled
center opening of the cam. Remove the cam.

H-17.
Distributor Inspection

If
the shaft and bearings are worn sufficiently
to allow .005" or more
looseness
of the shaft,
they
must be replaced. Before installing new bearings,
soak them in medium grade
engine
oil and allow
them to
drain.
Wipe all oil from the upper part of
the housing.

Important:
After new bearing installation,
drill
a

y%"
[3,2 mm.] lubrication
hole
through the upper bearing
before
installing the drive shaft. Refer
to Fig. H-8 item 16.

At
assembly, apply a film of grease to the upper
drive
shaft washer and put a small amount of
grease in the bearing bore just
above
the bearings.

Lubricate
the governor mechanism sparingly with
medium grade
engine
oil in the oiler mounted on
the side of the housing and 5 drops on the
left

located in the center opening of the cam directly

below
the rotor. Place a very light smear of grease
on the cam and 1 drop of oil on the breaker arm pivot.
Before installing the distributor, check the friction

spring
mounted on the lower end of the drive shaft

and
replace it if worn or damaged. Inspect rod end of vacuum advance mechanism
for
excessive
wear. Push rod
into
unit as far as
possible, hold finger tightly over nipple, then release rod. After about 15 seconds, remove finger
from nipple, and
notice
if air is drawn
into
unit.
If
not, diaphragm is leaking and unit must be
replaced.

H-18.
Installation and Ignition
Timing

If
the
engine
crankshaft has
been
rotated, with the
distributor off, it
will
be necessary to place No. 1
piston in firing position to correctly install the distributor. Refer to
Pars.
C-10 and
C-ll. Oil
the distributor housing where it bears in the

cylinder
block and install the distributor on the
cylinder
block. Mount the rotor on distributor shaft

and
turn
the shaft until the rotor
points
towards No. 1
spark
terminal tower position (when cap is installed) with the contact
points
just breaking. Move the rotor back and forth slightly until the

driving
lug on the end of the shaft enters the
slot

cut in the oil pump gear and slide the distributor
assembly down
into
place. Rotate the distributor
body
until the contact
points
are just breaking.
Install
the hold down screw.

H-19.
Ignition
Coil
— F4 Engine

The
sealed coil
does
not require any special service
other than keeping the terminals and wire con­ nection clean and tight.

The
positive (+) terminal of the coil is connected
to the ignition switch and is also connected directly
to the starter solenoid to by-pass the resistance

during
cranking of
engine.

The
negative
(—) terminal is connected to the
distributor. The secondary (High tension) terminal
is connected by a short cable to the center terminal

in
the distributor cap.

Note:
Always make certain the coil wires are con­
nected to the proper coil terminals to ensure cor­
rect coil polarity.

H-20. DELCO DISTRIBUTOR
—
DAUNTLESS
V-6
ENGINE
The
distributor (Fig. H-10) is mounted at the
left

front of the
engine
on the timing chain cover. It
is driven by a
spiral
gear on the camshaft. The

spark
advance is fully automatic, being controlled 182

ELECTRICALJ
SYSTEM

d.
Inspect for
excessive
wear
between
centrifugal

weights
and advance cam and pivot pins.
Turn
weight
base plate in a clockwise direction until
weights
are fully extended. Release and allow
springs to return
weights
to
retard
position. Repeat several times. Springs should return
weights
to
stop
without sticking and there should be no
excessive
free
movement
in the
retard
position. Inspect
springs for distortion and fatigue.
e. Inspect cam
lobes
for scoring or
excessive
wear.
Check
weight
base plate for binding or
excessive

looseness
on distributor shaft.

f.
Check
breaker plate for
excessive
looseness
on
outside
diameter of upper distributor shaft bushing.
Check
breaker plate ground lead for poor
spot
we
Id

at plate end and for
loose
or frayed terminal con­
nections.
g.
Check
for
excessive
wear
between
distributor
shaft and bushings in housing. Inspect shaft for distortion. Inspect gear for scoring of
teeth
or

excessive
wear.

h.
Inspect rod end of vacuum advance mechanism
for
excessive
wear. Push rod
into
unit as far as
possible, hold finger tightly over nipple, then re­
lease
rod. After about 15 seconds, remove finger
from nipple, and
notice
if air is drawn
into
unit.
If
not, diaphragm is leaking and unit must be
replaced.

H-29.
Distributor Reassembly

Refer
to Fig. H-l5.

a.
Install
distributor
primary
lead and rubber grommet in distributor housing. Mount vacuum
advance unit on housing with two
slotted
attaching
screws; insert ground lead terminal of breaker plate under outer mounting screw.
b.
Install
felt
washer over upper shaft bushing of
distributor housing and apply a few drops of light

oil.
Secure breaker plate to upper bushing with re­ tainer. See Fig. H-17.
12767

FIG.
H-17—INSTALLING
BREAKER
PLATE
ON
DISTRIBUTOR
HOUSING
(DELCO)

1—
Breaker
Plate
2—
Retainer

3—
Retainer
Groove
4—
Lubricant
Reservoir c.
Install
distributor cam and
weight
base plate
on distributor shaft.

d.
Insert distributor shaft
into
distributor housing.
Install
centrifugal advance
weights
and springs on

cam
and
weight
base plate. e. Fasten driven gear to shaft with pin. Be care­
ful
not to damage gear.

f.
Secure condenser and bracket to breaker plate
with
slotted
screw.
g.
Install
breaker point assembly over
boss
on
breaker
plate; secure with two
slotted
screws and
lock washers. Apply one drop of light oil to breaker

arm
pivot. Connect condenser and coil
primary

leads to breaker point assembly.

h.
Apply a small amount of high temperature cam

and
ball
bearing lubricant to a clean cloth; hold cloth against distributor cam while turning
distri­
butor shaft.

Caution:
Do not apply
excessive
grease. Petro­
leum jelly is not suitable as a distributor cam
lubri­
cant.

i.
Make preliminary adjustment of breaker point
gap, as described in Par. C-10.

].
Secure rotor to centrifugal timing advance mech­
anism with two screws, lock washers, and flat
washers.

Note:
The square and round
lugs
on the rotor must
be positioned in the corresponding
holes
in the

weight
base plate.
k. If a reliable distributor tester is available, check
the distributor to make certain that the centrifugal

and
vacuum advance mechanisms are operating
according to specifications.

Note:
Mount distributor in tester with all end play
of the distributor shaft in upward position; this

will
eliminate any possible drag
between
the centri­ fugal advance cam and
weight
base plate.

I.
Install
new
O-ring
seal on distributor housing.

H-30.
Distributor
Installation
and
Timing

a.
Insert distributor shaft
into
timing gear cover
of
engine
so that rotor is pointing to
mark
made on distributor base (Fig. H-14), with vacuum advance
unit pointing in exact, original direction (Fig.

H-18).

b.
Install
distributor clamp and
bolt
with lock
washer, leaving
bolt
just
loose
enough
to permit
movement
of the distributor with heavy hand
pressure.

C.
Connect
primary
wire to distributor side of coil.
Install
distributor cap on distributor housing. Press

screwdriver
into
upper
slotted
ends
of two cap
retainers.
Turn
retainers clockwise to secure cap to distributor.

d.
If
spark
cables were disconnected from
distri­

butor cap, connect them. Wires must be pushed

all
the way down
into
the distributor cap terminals
and
onto
the
spark
plugs. Nipples must be pushed
firmly
over the terminals;
boots
must be pushed

firmly
over the
spark
plugs. 186