1953 JEEP DJ cooling

'Jeep*
UNIVERSAL SERIES
SERVICE
MANUAL

D
insulator
mountings attached to the frame side

rail
brackets. The
rear
of the engine-transmission
assembly is supported by a rubber insulator
mounting under the
rear
of the transmission on
the frame center cross member.
This
cross member
is bolted to the frame side
rails
so that it can be
dropped when removing the transmission or engine-

transmission
assembly. The rubber insulators allow
free side and vertical oscillation to effectively

neutralize
engine
vibration at the source.

The
rubber
insulator mountings should be inspected
for separation and deterioration by jacking the
power plant away from the frame, near the sup­
ports. Vibration cannot be effectively absorbed by
separated or worn insulators. They should be re­ placed if faulty.

D-4.
Engine
Ground
Strap

To
be sure of an
effective
ground for the electrical

circuits,
a ground strap bridges the right front

engine
support to the chassis. The connections of this strap must be kept clean and tight for proper
operation of the electrical system.

D-5. ENGINE REMOVAL

Should
the
engine
require overhauling, it is neces­

sary
to remove it from the vehicle. The following procedure covers removal of the
engine
only.

The
engine, transmission and transfer case may be
removed as a unit by removing (in addition to the following procedure) the radiator guard and the
access plates in the floor pan.

a.
Drain
the cooling system by opening the
drain
cocks at the
bottom
of the radiator and lower right
side of the cylinder block.

b.
Disconnect the battery at the positive terminal
to avoid the possibility of short
circuit.

c. Remove the air cleaner horn from the carburetor
and
disconnect the breather
hose
at the oil filler
pipe.

d.
Disconnect the carburetor choke and throttle controls by loosening the clamp
bolts
and set
screws.

e. Disconnect the fuel-tank-to-fuel-pump line at the fuel pump by unscrewing the connecting nut.
f- Plug the fuel line to prevent fuel leakage.
g. Remove the radiator and radiator grille support

rods.

h. Remove the upper and lower radiator
hoses
by
loosening the
hose
clamps and slipping the clamps
back
on the
hose.
If so equipped, remove the heater

hoses
(one to the water pump, one to the
rear
of
the cylinder head) in the same manner.

i.
Remove the four
bolts
from the fan hub and re­

move
the fan hub and fan blades.

j.
Remove the four radiator attaching screws. Re­
move
the radiator and shroud as one unit, k. Remove the starting motor cables. Remove the

starting
motor.

I.
Disconnect the wires from the alternator or
generator. Disconnect the ignition
primary
wire
at the ignition coil.
NOTE:
ON
ENGINES EQUIPPED WITH EX­

HAUST
EMISSION CONTROL, REMOVE THE
AIR
PUMP,
AIR
DISTRIBUTION
MANI­
FOLD,
AND
ANTI-BACKFIRE (DIVERTER)

VALVE.
SEE SECTION
Fl
FOR PROCEDURE.
m.
Disconnect the oil pressure and temperature
sending unit wires at the units.

n.
Disconnect the exhaust pipe at the exhaust
manifold by removing the stud nuts.

o.
Disconnect the
spark
plug cables at the plugs

and
remove the cable bracket from the rocker arm cover stud.

p.
Remove the rocker arm cover by removing the
attaching stud nuts.

q.
Attach a lifting bracket to the
engine
using
existing head bolt locations. Be sure the
bolts
selected
will
hold the
engine
with the weight

balanced.
Attach lifting bracket to a boom hoist,

or
other lifting device, and take up all slack,
r.
Remove the two nuts and
bolts
from each front

engine
support. Disconnect the
engine
ground strap.
Remove the
engine
supports.
Lower
the
engine
slightly to permit access to the two top
bolts
on
the flywheel housing.
s. Remove the
bolts
which attach the flywheel
housing to the engine.

t.
Pull
the
engine
forward, or
roll
the vehicle back­

wards,
until the clutch clears the flywheel housing.

Lift
the
engine
from the vehicle.

D-6. ENGINE DISASSEMBLY

Engine
disassembly is presented in the sequence to be followed when the
engine
is to be completely
overhauled after removal from the vehicle. Some
of the operations of the procedure are also ap­
plicable
separately with the
engine
in the vehicle,

provided
that wherever necessary the part of the

engine
to be worked on is first made accessible by
removal
of
engine
accessories or other parts.

When
the disassembly operations are performed

with
the
engine
out of the vehicle, it is assumed,
in
this procedure, that all of the accessories have been removed
prior
to starting the disassembly

and
the oil has been drained.
In
addition to the instructions covering operations
for disassembling the
engine
out of the vehicle,

special
instructions are given to cover different
operations required when disassembly is
done
with the
engine
installed.

During
disassembly operations, the
engine
should
be mounted in a suitable
engine
repair
stand. Where

practicable,
modify or adapt an existing repair

stand
as necessary to accommodate the engine. If

an
engine
repair stand is not used, take care to

perform
disassembly operations in a manner that

will
protect personnel against an accident and the
engine
and its parts against damage.

NOTE:
If the
engine
is being disassembled because
of possible valve failure, check the valve tappet
clearance
before disassembly. Improper valve

clearance
could be the possible cause of valve

failure,
indicating a need for more frequent valve
checks and adjustments. 41

D
HURRICANE
F4
ENGINE
Note:
Check
the condition of the rubber O-rings.
Defective O-rings could be the major cause of oil
leakage into cylinders. Always discard and replace

all
O-rings removed as only new O-rings should be installed at reassembly.

D-18.
Ream
Cylinder
Bore Ridges

To
prevent breaking the piston lands, the ridge
at the top of each cylinder bore must be removed

first.
To remove this ridge, use a cylinder ridge
reamer,
as shown in Fig. D-3 following the instruc­
tions furnished by the reamer manufacturer. Use

care
not to cut below the top of the upper ring
travel
in the bore. Keep each piston top covered

with
an oil-soaked cloth to prevent cuttings from
falling
into the cylinder.

Note:
This
operation should be performed at this
time before the
engine
is rotated for the sequence

steps
following.

D-19.
Remove Oil Pan
Rotate the
engine
to the upside down position.
Remove the screws and lockwashers that attach
the oil pan to the cylinder block. Remove the oil

pan
and gasket.
Discard
the gasket.

D-20.
Remove Piston and Connecting
Rod
Assemblies
Remove the stamped locking nuts from the lower
end of each connecting rod bearing bolt. Remove
the connecting rod nuts. Remove the bearing cap evenly. Push the connecting rod and piston as­
sembly out of the cylinder block with the handle end of a hammer until the piston rings are free from
the cylinder bore. Remove the piston and connecting rod assembly

from
the top of the cylinder block. Reassemble the
connecting rod bearing cap with the bearings in
place in the rod from which it was removed. Rotate
the crankshaft and follow the same procedure until
all
the piston and connecting rod assemblies are
removed.
Pistons and connecting rod assemblies may be removed for repair with the
engine
in the vehicle after draining the cooling system, removing the

oil
pan and the cylinder head, and reaming the ridges as previously described.

D-21.
Remove
Timing
Gear
Cover

Remove the bolts, nuts, and lockwashers, that at­
tach
the timing gear cover to the engine. Remove
the cover, timing pointer, and cover gasket.
Dis­
card
the gasket. Remove the crankshaft oil seal

from
the timing gear cover and discard the seal. Remove the oil slinger and spacer from the
crank­

shaft.

D-22.
Remove
Timing
Gears

Use puller W-172 for pulling both the crankshaft
and
the camshaft gears.
With
the threaded cap-
screws supplied, adapt the puller to the crankshaft
FIG.
D-5—PULLING TIMING GEARS

1—
Puller
W-172 2—
Camshaft
Gear
gear and
pull
the gear.
With
the special hook-type

puller
bolts
that fit behind the camshaft gear
flange,
pull
the camshaft gear. Remove the Wood­

ruff
Keys.

D-23.
Remove
Front
End Plate
Remove the screws and lockwashers that attach the
front end plate to the cylinder block. Remove the
front end plate and gasket.
Discard
the gasket.
D-24. Remove
Clutch

Remove four
bolts
and lockwashers diagonally

opposite
that attach the clutch assembly to the
flywheel, leaving two
opposed
bolts
to be
loosened
alternately until the clutch spring pressure is re­
lieved.
Then,
support the clutch assembly with
one hand while removing the two remaining bolts.

For
information on disassembly, inspection, repair

and
assembly of the clutch refer to Section I. In­
structions for removing the clutch when the
engine
is in the vehicle are also given in Section I.

D-25.
Remove Flywheel

The
flywheel is attached to the crankshaft with two tapered dowel
bolts
and four special bolts.
Remove
these
attaching parts. Use a pry bar be­ tween the flywheel and the back of the
engine
and
carefully
loosen
the flywheel from the crankshaft.

If
the flywheel is to be removed with the
engine

in
the vehicle, the transmission and clutch must
first be removed as detailed in Section I.

D-26.
Remove
Crankshaft

Slide
the crankshaft thrust washer and all end-play

adjusting
shims off the front end of the crankshaft.

Pull
the two pieces of
rear
main bearing cap packing out of position
between
the side of the bearing cap

and
the cylinder block.

Note
the marks on the bearing caps and cylinder
block for bearing number and position. 44

D

HURRICANE
F4
ENGINE
D-112.
SERVICE
DIAGNOSIS

Poor
Fuel
Economy Ignition Timing Slow or Spark Advance Stuck

Carburetor
Float High
Accelerator Pump Not Properly Adjusted
High
Fuel
Pump Pressure

Fuel
Leakage
Leaky
Fuel
Pump Diaphragm
Loose Engine Mounting Causing High
Fuel
Level

in
Carburetor

Low
Compression Valves Sticking

Spark
Plugs Bad

Spark
Plug Cables Bad Weak
Coil
or Condenser Improper Valve Tappet Clearance

Carburetor
Air Cleaner Dirty
High Oil Level in Air Cleaner Dragging Brakes

Front
Wheels Out of Alignment
Tires
Improperly Inflated Inaccurate Odometer

Faulty
Fuel
Tank
Cap

Clogged
Muffler or Bent Exhaust Pipe

Lack
of Power
Low
Compression Ignition System (Timing Late)
Improper Functioning Carburetor or
Fuel
Pump

Fuel
Lines
Clogged
Air
Cleaner Restricted
Engine Temperature High Improper Tappet Clearance
Sticking Valves Valve Timing Late

Leaky
Gaskets
Muffler
Clogged
Bent Exhaust Pipe

Defective
Spark Plugs—Clean or Replace
Defective
Breaker Points—Replace
Points

Incorrect Breaker Point Gap—Reset
Points

Defective
Condenser or Coil—Replace
Loose Electrical Connections—Locate and Tighten
Broken Valve Spring—Replace Spring Broken Piston or Rings—Replace
Defective
Head Gasket—Replace Gasket
Cracked
Distributor Cap—Replace Cap

Low
Compression
Leaky
Valves
Poor Piston Ring Seal Sticking Valves
Valve Spring Weak or Broken
Cylinder
Scored or Worn
Tappet Clearance Incorrect
Piston Clearance too Large
Leaky
Cylinder Head Gasket
Burned Valves and
Seats
Sticking Valves or too Loose in Guides Improper Timing
Excessive Carbon Around Valve Head and Seat Overheating
Valve Spring Weak or Broken Burned Valves and Seats—Continued
Valve Tappet Sticking
Valve Tappet Clearance Incorrect
Clogged
Exhaust System
Valves Sticking Warped Valve Improper Tappet Clearance
Carbonized or Scored Valve
Stems
Insufficient Clearance Valve Stem to Guide
Weak or Broken Valve Spring Valve Spring Cocked Contaminated Oil
Overheating Inoperative Cooling System
Thermostat Inoperative Improper Ignition Timing
Improper Valve Timing
Excessive Carbon Accumulation

Fan
Belt too Loose

Clogged
Muffler or Bent Exhaust Pipe

Oil
System Failure
Scored or Leaky Piston Rings

Popping-Spitting-Detonation
Improper Ignition
Improper Carburetion
Excessive Carbon
Deposit
in Combustion
Cham­
bers
Poor Valve Seating Sticking Valves
Broken Valve Spring Tappets Adjusted too Close

Spark
Plug Electrodes Burned
Water or Dirt in
Fuel
Clogged
Lines Improper Valve Timing
Excessive Oil Comsumption Piston Rings Stuck in Grooves, Worn or Broken Piston Rings Improperly Fitted or Weak Piston Ring Oil Return
Holes
Clogged
Excessive Clearance, Main and Connecting Rod
Bearings

Oil
Leaks at Gaskets or Oil Seals
Excessive Clearance, Valve Stem to Valve Guide (Intake)

Cylinder
Bores Scored, Out-of-Round or Tapered Too Much Clearance, Piston to Cylinder Bore
Misaligned Connecting Rods
High Road
Speeds
or Temperature
Crankcase
Ventilator Not Operating
Bearing Failure
Crankshaft
Bearing Journal Out-of-Round

Crankshaft
Bearing Journal Rough

Lack
of Oil
Oil
Leakage
Dirty
Oil

Low
Oil Pressure or Oil Pump Failure
Drilled
Passages
in Crankcase or Crankshaft
Clogged

Oil
Screen Dirty Connecting Rod Bent 70

'Jeep'
UNIVERSAL SERIES
SERVICE
MANUAL

Dl

DAUNTLESS
V-6
ENGINE
Contents

SUBJECT
PAR.
SUBJEC

GENERAL
.... . . Dl-1 Oil Pump Cl(
ENGINE DESCRIPTION
D1-2

Engine
Mounts Dl-3

ENGINE REMOVAL
Dl-4
ENGINE DISASSEMBLY
Dl-5
Alternator
and Fan Belt Dl-11
Camshaft
.... Dl-26
Cooling Fan and Water Pump.
......
.Dl-12
Crankshaft
Front Oil Seal .Dl-21

Crankshaft
Pulley D1-17
Crankshaft
Vibration Damper Dl-18

Cylinder
Head Assembly Dl-24

Distributor
Dl-9
Exhaust
Manifold .Dl-8

Flywheel
Dl-28

Flywheel
Housing and
Clutch
Dl-27
Fuel
Pump. ... . .Dl-10
Intake
Manifold and
Carburetor
Assembly.
.............
.Dl-7

Main
Bearing and Crankshaft. Dl-32 Mounting Engine on Engine Stand. . . . .Dl-6

Oil
Dipstick. Dl-16
Oil
Filter
Dl-13
Oil
Pan.. ...
.......
.Dl-29
Oil
Pressure Sending Unit Dl-15

Oil
Pump Dl-19
Oil
Pump Intake Pipe and Screen Dl-30
Piston and Rod Assembly. Dl-31
Push
Rod and Valve
Lifter.
.Dl-25
Rocker
Arm Cover Dl-23
Starter
Motor Dl-14

Timing
Chain
and Sprocket Dl-22
Timing
Chain
Cover Dl-20

ENGINE CLEANING, INSPECTION AND REPAIR
. . ... .Dl-33
Camshaft
Cleaning and Inspection Dl-55
Connecting Rod Bearing Inspection
and
Fitting .Dl-49

Crankshaft
Cleaning Dl-38
Crankshaft
Inspection and Repair Dl-39
Crankshaft
Main Bearing Cleaning
and
Inspection Dl-41

Crankshaft
Main Bearings. Dl-40

Crankshaft
Pulley Inspection. Dl-70
Crankshaft
Vibration Damper Inspection. D1-69

Cylinder
Block .Dl-34
Cylinder
Block Cleaning Dl-35
Cylinder
Block Inspection Dl-36

Cylinder
Block Repair. .Dl-37
Cylinder
Head and Valve Repair .Dl-63

Cylinder
Head and Valve Cleaning
and
Inspection.. . .Dl-62

Flywheel
Cleaning and Inspection Dl-52

Flywheel
Housing Cleaning
and
Inspection Dl-54

Hydraulic
Valve
Lifter
Leakdown Test. .Dl-57
Main
Bearing Fitting or

Shim
Stock Dl-42, Dl-43

Oil
Pan Cleaning and Inspection .Dl-51
PAR.
and
Inspection. .... .Dl-68

Oil
Pump Intake and Screen Cleaning. . .Dl-50
Piston and Rod Assembly.
...........
.Dl-48
Piston and Rod Cleaning and Inspection.D1-45
Piston and Rod Disassembly Dl-44
Piston Fitting Dl-46
Piston Ring Fitting. .Dl-47

Ring
Gear
Replacement. .Dl-53
Rocker
Arm Assembly. Dl-60
Rocker
Arm Cleaning and Inspection. . .Dl-59

Rocker
Arm Cover Cleaning

and
Inspection D1-65

Rocker
Arm Disassembly .Dl-58
Timing
Chain
and Sprocket Inspection. . .Dl-66

Timing
Chain
Cover Cleaning

and
Inspection.. . Dl-67

Valve
Installation D1-64
Valve
Lifter
and Push Rod

Cleaning
and Inspection. . Dl-56

Valve
Removal Dl-61

ENGINE REASSEMBLY
Dl-71
Alternator
and Fan Belt Dl-96

Camshaft
Dl-80
Clutch
and Flywheel Housing Dl-79
Cooling Fan.. . .Dl-95
Crankshaft
End Play Check. . Dl-74

Crankshaft
Front Oil Seal Dl-85
Crankshaft
Pulley Dl-89
Crankshaft
Vibration Damper Dl-88
Cylinder
Block and Crankshaft
Rear
Oil Seals Dl-72

Cylinder
Head Assembly .Dl-82

Distributor
Dl-99

Exhaust
Manifold Dl-98
Flywheel
.Dl-78
Fuel
Pump.. .. . Dl-97
Intake
Manifold and Carburetor Assembly Dl-101

Main
Bearing and
Crankshaft
Installation
.
Dl-73

Oil
Filter
Dl-93
Oil
Level
Dipstick Dl-90

Oil
Pan Dl-77
Oil
Pressure Sending Unit Dl-91

Oil
Pump.. .Dl-87
Oil
Pump Intake and Screen Assembly. .Dl-76
Piston and Rod Installation Dl-75

Rocker
Arm Cover. Dl-83

Spark
Plugs.. Dl-100
Starter
Motor Dl-92
Timing
Chain
and Sprocket.
..........
.Dl-84

Timing
Chain
Cover Dl-86
Valve
Lifter
and Push Rod Dl-81

Water
Pump. Dl-94

ENGINE INSTALLATION
Dl-102

FINAL
IN-VEHICLE
ADJUSTMENTS.
D1-103

SERVICE
DIAGNOSIS
Dl-104
ENGINE SPECIFICATIONS
. .Dl-105 75

'Jeep*
UNIVERSAL SERIES SERVICE
MANUAL

Dl

12710

FIG.
D1
-3—HYDRAULIC VALVE
LIFTER
ASSEMBLY, CROSS-SECTIONAL VIEW
1—
Snap
Ring
6—Ball Retainer

2— Rod
Seat
7—Plunger Spring

3—
Oil
Inlets
8—Lifter
Body

4—
Plunger
9—Bronzed
Cap
5— Feed
Hole
sages
in the block and cylinder head.

The
water cooled system is pressurized to provide efficient
engine
cooling. It consists of a centrifugal-
type water pump, mounted on the timing chain cover, and is driven by the
engine
fan pulley. The
pump provides coolant flow equally to both
cylin­
der banks under control of a thermostat. Coolant
flow is around the cylinders and through the
cylinder
head to dispel the heat of combustion in
the engine.

Dl-3.
Engine Mounts

The
engine-transmission unit is mounted to the chassis at three points by rubber pads. The two
front mounts are bolted to the
engine
cylinder
block and the frame members. These mounts sup­ port most of the
engine
weight, and absorb
vibra­

tion which would otherwise be caused by changes
in
engine
output torque. The single
rear
mount is
placed
between
the transmission and the trans­ mission support. It supports part of the engine'

and
transmission weight, and locates the
rear
of
the
engine
with respect to the centerline of the
vehicle.

Dl-4. ENGINE REMOVAL
To
remove the
engine
from the vehicle follow the
procedurers listed below:

a.
Remove hood. b. Disconnect battery cables from battery and
engine. c. Remove air cleaner.

d.
Drain
coolant from radiator and engine.
e.
Drain
engine
oil.
f. Disconnect alternator wiring harness from con­ nector at regulator.

cj.
Disconnect the fuel evaporative purge line con­ nected to the
P.C.V.
valve.

h.
Disconnect upper and lower radiator
hoses
from
the engine.

i.
Remove right and left radiator support
bars,

j.
Remove radiator from the vehicle.

k.
Disconnect
engine
wiring harnesses from con­
nectors located on
engine
firewall.
I.
On
engines
equipped with exhaust emission con­

trol,
remove the air pump, air distribution manifold,

and
anti-backfire (gulp) valve. See Section F2 for
procedure.

m.
Disconnect battery cable and wiring from en­

gine
starter assembly.

n.
Remove
engine
starter assembly from engine,

o.
Disconnect
engine
fuel
hoses
from fuel lines at

right
frame
rail,
p. Plug fuel lines.

q.
Disconnect choke cable from carburetor and cable support bracket mounted on engine,
r.
Disconnect exhaust pipes from right and left

engine
manifolds.
s. Place
jack
under transmission and support trans­
mission weight.
f. Remove
bolts
securing
engine
to front motor mounts.

u.
Attach suitable sling to
engine
lifting
eyes
and,
using hoist, support
engine
weight.
v. Remove
bolts
securing
engine
to flywheel housing.
w. Raise
engine
slightly and slide
engine
forward
to remove transmission main shaft from clutch plate spline.

Note:
Engine and transmission must be raised
slightly to release the main shaft from the clutch
plate while sliding the
engine
forward.
x. When
engine
is free of transmission shaft raise

engine
and remove from vehicle,
y. Place
engine
on suitable blocking or
engine
stand and remove sling from engine.

Dl-5.
ENGINE DISASSEMBLY

Engine
disassembly is presented in the sequence to be followed when the
engine
is to be completely
overhauled after removal from the vehicle. Some of the operations of the procedure are also appli­cable separately with the
engine
in the vehicle,
provided that wherever necessary the part of the
engine
to be worked on is first made accessible by removal of
engine
accessories or other parts.

When
the disassembly operations are performed
with
the
engine
out of the vehicle, it is assumed,
in
this procedure, that all of the accessories have
been removed
prior
to starting the disassembly and
the oil has been drained.

Dl

DAUNTLESS
V-6
ENGINE
In
addition to the instructions covering operations
for disassembling the
engine
out of the vehicle, special instructions are given to cover different
operations required when disassembly is
done
with
the
engine
installed.

During
disassembly operations, the
engine
should be mounted in a suitable
engine
repair stand.

Where
practicable, modify or adapt an existing re­

pair
stand as necessary to accommodate the
engine.
If
an
engine
repair stand is not used, take care to

perform
disassembly operations in a manner that
will
protect personnel against an accident and the
engine
and its parts against damage.

Dl-6.
Mounting Engine
On
Engine Stand

Refer
to Fig. Dl-4.
a.
With
the
engine
supported by a hoist, remove
the clutch housing and clutch. Match
mark
the flywheel and the clutch cover before disassembly to assure proper reassembly.
b. Position the
engine
on the
engine
stand.
c. Release
some
tension of the hoist cables and secure
engine
to stand.

d.
Make sure the position lock on the
engine
stand
is tight to prevent the
engine
from accidentally
inverting.

e.
Release the hoist cables.
FIG.
D1
-4—ENGINE
MOUNTED
ON
STAND

1—
Spacer
J-8690-6
A—Bolt,
i/2-NC
x 3i/2"

2—
Bolt,
3/a-NC
x 4*/2" 5—Adapter 21316-J 3—
Engine
Mounting Stand
Dl-7.
Remove Intake Manifold
and

Carburetor Assembly

Disconnect crankcase vent
hose,
distributor vacuum

hose,
and fuel line from carburetor. Disconnect two distributor leads from ignition coil. Disconnect

wiring
harness from coolant temperature sending

unit.
Remove ten cap
bolts
which attach intake
manifold to cylinder heads. Remove intake mani­
fold assembly and gaskets from
engine.

Dl-8. Remove Exhaust Manifold
The
engine
has two exhaust manifolds. Remove five attaching screws, one nut, and exhaust mani­
fold from each cylinder head.

Dl-9.
Remove Distributor

Disconnect vacuum
hose
and wiring harness from

distributor.
Disconnect spark plug cables from
spark
plugs. Remove sparks plugs from
engine.
Pull

spark
plug cable retainers from brackets on rocker

arm
covers. Remove mounting screw, retainer

bracket,
and distributor from timing chain cover.
If
timing chain and sprockets are not to be re­
moved from
engine,
note
position of distributor
rotor so that it can be installed in identical position.

Dl-10. Remove
Fuel Pump
Disconnect output fuel line from fuel pump. Re­
move
two mounting bolts, fuel pump, and gasket

from
timing chain cover.

Dl-11.
Remove Alternator
and Fan
Belt

Disconnect wiring harness from alternator. Remove nut and flat washer which fasten alternator to
adjustment bracket. Pivot alternator
inward,
to­

ward
engine
cylinder block, to relieve fan belt
tension. Remove fan belt from pulleys. Remove
two attaching screws, mounting bracket, and alter­ nator from right cylinder head of
engine.

Dl-12.
Remove Cooling
Fan and
Water Pump

Refer
to Fig. Dl-5.
Remove four cap screws, lock washers, cooling fan,

fan
hub, and fan drive pulley from flange of water
pump shaft. Remove nine attaching screws, water
pump, alternator adjustment bracket, and water pump from timing chain cover.

Dl-13.
Remove
Oil
Filter

Unscrew
oil filter from
engine
oil pump.

Dl-14.
Remove Starter Motor

Disconnect wiring harness from starter motor and
solenoid. Remove two attaching screws, starter motor, solenoid, and motor attaching bracket from

engine
flywheel housing and cylinder block.

Dl-15.
Remove
Oil
Pressure Sending Unit

Disconnect wiring harness from oil pressure send­
ing unit. Remove oil pressure sending unit from

engine
cylinder block.

Dl-16.
Remove
Oil
Dipstick

Withdraw
and remove oil level dipstick and dip­

stick
tube
from
engine
cylinder block.

Dl-17.
Remove Crankshaft Pulley

Remove six attaching screws and crankshaft pulley

from
crankshaft vibration damper. 80

'Jeep'
UNIVERSAL
SERIES
SERVICE
MANUAL

Dl

13296

FIG.
Dl-5—ENGINE
LUBRICATION
AND
COOLING
PARTS

1— Bolt and
Lock
Washer
2—
Fan
Assembly
3—
Fan
and Alternator Belt
4—
Fan
Driven Pulley 5— Water Pump Assembly
6—
Hose
Clamp 7— Thermostat Bypass
Hose

8—Hex
Head Bolt
9— Water Outlet Elbow
10— Water Outlet Elbow Gasket
11— Thermostat
12— Water Pump Gasket
13— Impeller and Insert, Water Pump
14— Water Pump Seal 15— Dowel Pin % x Vfc"
16— Water Pump Cover
17— Bolt,
1/4-20
x 1"
18— Water Pump Shaft and Bearing
19—
Fan
Hub
20—
-Oil
Suction Pipe Gasket
21—
Oil
Suction Housing, Pipe and Flange
22— Bolt,
y4-20
x s/8"
23—
Oil
Pump Screen
24—
Oil
Dipstick
25—
Oil
Pan Gasket
26—
Oil
Pan Assembly
27—
Drain
Plug Gasket
28—
Drain
Plug 29— Screw and
Lock
Washer #6-18 x %
30—
Oil
Pump Shaft and Gear
31—
Oil
Pump Cover Gasket
32— Valve Bypass and Cover Assembly
33—
Oil
Pressure Valve 34— Valve Bypass Spring
35—
Oil
Pressure Valve Cap Gasket
36—
Oil
Pressure Valve Cap
37— Screw V4-20 x lVg"
38— Screw 1/4-20 x 1W' 39—
Fan
Driving Pulley
40— Hex. Head Bolt, x 1"
Dl-13.
Remove
Crankshaft
Vibration Damper

Refer
to Fig. Dl-6.
Remove cap screw and flat washer which attach

crankshaft
vibration damper to crankshaft. Tap

vibration
damper with a soft-headed hammer to remove it from crankshaft.

Dl-19.
Remove Oil Pump
Remove five screws, oil pump cover, and gasket

from
right side of timing chain cover. Remove
two oil pump gears.

D1-20.
Remove Timing Chain Cover

Refer
to Fig. Dl-6. Remove two
bolts
which attach oil pan to timing

chain
cover. Remove five mounting bolts, timing

chain
cover, and gasket from cylinder block of
engine.

Note:
Water pump must be removed from timing

chain
cover before timing chain cover is removed

from
cylinder block.
Dl-21.
Remove Crankshaft Front
Oil
Seal

Refer
to Fig. Dl-6.
Use timing cover aligner and oil seal remover
tool
J-22248 to remove oil seal.

Dl-22.
Remove Timing Chain
and
Spocket

a.
Temporarily install vibration damper (Fig.

Dl-6)
bolt and washer in end of crankshaft.
Turn

crankshaft
so sprockets are positioned with index

marks
aligned as shown in Fig. Dl-7.
This
will

make it easier to install parts. Remove vibration
damper bolt and washer; rap the wrench handle
sharply
to start the bolt without changing position
of sprockets.

Note:
It is not necessary to remove timing chain
dampers unless they are worn or damaged and

require
replacement.
b. Remove front crankshaft oil slinger.
c. Remove bolt and special washer which retain
camshaft distributor drive gear and fuel pump
eccentric at forward end of camshaft. Remove gear
and
eccentric from camshaft. 81

Dl
DAUNTLESS
V-6
ENGINE

FIG.
Dl-41—WATER
PUMP
AND
TIMING CHAIN COVER BOLT LOCATION
Cover
Bolts

alternately and evenly 8 to 12 lb-ft. [1,10 a 1,66

kg-m.].

Dl-88.
Install
Crankshaft
Vibration
Damper

a.
Lubricate
the vibration damper hub
before
in­
stallation to prevent
damage
to the crankshaft
front oil seal during installation and when the

engine
is first started.
b.
Install
the vibration damper on the crankshaft.
Secure it with its attaching flat washer and screw.

Torque
the screw to a minimum of 140 lb-ft.
[19,35
kg-m.].

Dl-89.
Install
Crankshaft Pulley
Secure the crankshaft pulley to the crankshaft

vibration
damper with six screws. Torque screws 18 to 25 lb-ft. [2,5 a 3,4 kg-m.].

Dl-90.
Install
Oil
Level
Dipstick

Insert
oil level dipstick
into
the dipstick tube.

Dl-91.
Install
Oil
Pressure Sending Unit

Install
oil pressure sending unit in cylinder block.
Connect electrical wiring harness to unit.

Dl-92.
Install Starting Motor

Secure starting motor and
solenoid
assembly to
the flywheel housing and cylinder block with two attaching screws. Torque screw, which attaches this
assembly to the flywheel housing, 30 to 40 lb-ft. [4,1 a 5,5 kg-m.]. Torque screw, which attaches

bracket
to cylinder block, 10 to 12 lb-ft. [1,4 a 1,7 kg-m.].
Dl-93.
Install
Oil
Filter

Install
a new oil filter
element
at oil filter nipple,
at
left
side
of timing chain cover. Torque 10 to 15 lb-ft. [1,38 a 2,07 kg-m.].

D1-94. Install Water Pump
Be
certain that mating surfaces of the water pump

and
timing chain cover are clean.
Install
a new
gasket
on the pump flange. Secure the pump and
alternator adjustment bracket to the cover with
nine attaching bolts. Torque
bolts
6 to 8 lb-ft. [0,83 a 1,10 kg-m.]. Refer to Fig. Dl-41.

D1-9S.
Install
Cooling Fan
Secure the cooling fan, fan hub, and fan drive
pulley to the water pump shaft
flange
with four
attaching screws. Torque screws 17 to 23 lb-ft. [2,35 a 3,18 kg-m.].

Dl-96.
Install
Alternator
and Fan
Belt

Mount the alternator and bracket assembly on
right
cylinder head with two attaching screws.

Torque
screws 30 to 40 lb-ft. [4,1 a 5,5 kg-m.].

Fasten
the alternator
loosely
to its adjustment
bracket
with attaching flat washer and nut.
Install

the fan
belt
on its pulleys. Pivot the alternator
outward,
away from cylinder block, to apply fan

belt
tension. Adjust fan
belt
tension to 80 lb. [36,2 kg.];
tighten
alternator-to-adjustment bracket
nut to secure adjustment
setting.
Connect wiring
harness to alternator.

Dl-97.
Install
Fuel Pump

Install
two mounting
bolts
and new
gasket
on

flange
of fuel pump. Secure pump to timing chain cover with screws; torque screws 17 to 23 lb-ft. [2,35 a 3,8 kg-m.]. Connect
output
fuel line to
pump.

Dl-98.
Install Exhaust Manifold

Secure each of two exhaust manifolds to corre­
sponding cylinder head with five attaching screws,
and
one nut. Torque screws and nut 15 to 20 lb-ft. [2,07 a 2,8 kg-m.]. See Fig. Dl-42.

Dl-99.
Install Distributor

Insert
distributor drive gear
into
distributor mount-
FIG.
Dl-42—EXHAUST
MANIFOLD INSTALLATION

1—Torque
Bolts—15
to 20
lb-ft.
[2,07 a 2,8
kg-m.]

102