2023 TOYOTA RAIZE buzzer

1934-2. Driving procedures
RAIZE_OM_General_BZ358E
✽: If equipped
Driving
4
⬛Power mode✽
⚫The power mode control will not be acti vated in any of the following situa-
tions:
⦁ When the shift lever is set to R
⚫Even when you have set the D assist switching steering switch to “ON”, turn-
ing the engine switch “OFF ” and turning it “ON” will automatically restore the
D assist switching steering switch to “OFF”.
⚫When the malfunction indicator lamp or the continuously variable transmis-
sion warning light
✽ is lit or flashing, or when the TFT color multi-information
display
✽ shows “Transmission System Malfun ction”, the vehicle will not enter
the power mode.
⬛Reverse warning buzzer
When shifting into R, a buzzer will so und to inform the driver that the shift
lever is in R.
WARNING
⬛When driving on slippery road surfaces
Do not accelerate or shift gears sudde nly. Sudden changes in engine braking
may cause the vehicle to spin or skid.
⬛To prevent an accident when releasing the shift lock
Before pressing the shift lock override button, make sure to set the parking
brake and depress the brake pedal.
If the accelerator pedal is accidentally depressed instead of the brake pedal
when the shift lock override button is pr essed and the shift lever is shifted out
of P, the vehicle may suddenly start, po ssibly leading to an accident resulting in
death or serious injury.
RAIZE_OM_General_BZ358E.book 193 ページ ２０２２年５月１７日　火曜日　午後１時５９分

1974-2. Driving procedures
RAIZE_OM_General_BZ358E
Driving
4
Parking brake
Operation instructions
aTo apply the parking brake, fully
pull the parking brake lever while
depressing the brake pedal
b To release the parking brake,
slightly raise the lever and lower
it completely while pressing the
button
⬛Parking the vehicle
➞P. 1 6 7
⬛Usage of parking brake in winter time
➞P. 2 3 9
⬛Parking brake non-release warning buzzer
➞P. 3 8 2
WARNING
⬛Important notice before driving
Do not drive the vehicle with the parking brake applied. Doing so will overheat
the brake and degrade its performance, leading to an unforeseen accident.
12
KBRO420601E
RAIZE_OM_General_BZ358E.book 197 ページ ２０２２年５月１７日　火曜日　午後１時５９分

2004-3. Operating the lights and windshield wipers
RAIZE_OM_General_BZ358E
✽: If equipped
⬛Automatic light off system
⚫While the lights are turned on, changi ng the engine switch from “ON” to
“ACC” or “OFF” will automatically turn off the lit lights.
⚫To turn the lights on again, turn “ON” the engine switch or move the head-
light switch to the position, and then move it to the or
position.
⬛Automatic light-off warning buzzer
When the headlights and tail lights are tu rned on with the engine switch set to
“ACC” or “OFF”, opening the driver’s door will cause the warning buzzer to
sound, letting the driver know that the lights have not been turned off.
⚫When the buzzer sounds , the warning message also appears for vehicles
with TFT color multi-information display. ( ➞P. 391)
⬛Power saving function
To prevent the battery from discharging, when the engine switch is set in “ACC”
or “OFF” and the headlights or tail lig hts are on, the power saving function is
activated and all lights are automatically turned off after about 10 minutes.
After light has been automatically turn ed off, perform any of the following
operations to cancel the power saving state and turn the lights back on.
⚫
When the engine switch is set to “ON”
⚫When the headlight switch is operated (However, the lights will turn off again
automatically after about 10 minutes)
⚫When one of the doors is opened or cl osed (However, the lights will automati-
cally turn off again after about 10 minutes)
⬛Customizations✽
You can change the timing of the headlight switch turning on and off automat-
ically at the position, etc.
(List of customizable features: ➞ P. 430)
NOTICE
⬛To prevent battery discharge
Do not leave the lights on for a long ti me with the engine stopped. Also, be
sure to turn off the lights when you leave the vehicle.
RAIZE_OM_General_BZ358E.book 200 ページ ２０２２年５月１７日　火曜日　午後１時５９分

2124-5. Using the driving support systems
RAIZE_OM_General_BZ358E
dBuzzer
BSM buzzer: When you have moved the turn signal lever to the side where the vehi-
cle is detected, the buzzer will sound.
RCTA Buzzer: When a vehicle approaching from the right or left rear end of your
vehicle is detected, the buzzer will sound.
WARNING
⬛To use the BSM function safely
The driver is responsible for driving the vehicle safely. It is th e driver’s responsi-
bility to be aware of the situations around the vehicle and drive safely.
The BSM function is an auxilia ry system designed to let the driver know of the
presence of a vehicle that has entere d or is rapidly approaching toward the
blind spot area of the outside rear view mirrors. Since this system alone is not
sufficient for determining the feasibility of changing lanes, overly relying on the
system could lead to an unforeseen accid ent, resulting in serious injury or
death.
This system does not work effectively depending on the circumstances. The
driver is responsible for checking the safety around the vehicle by using his/
her own eyes and the mirrors.
⬛To use the RCTA function safely
The driver is responsible for driving the vehicle safely. It is th e driver’s responsi-
bility to be aware of the situations around the vehicle and drive safely.
The RCTA function is an auxiliary system designed to let the driver know of the
presence of a vehicle that is approaching from the right or left rear of the vehi-
cle.
Even with the RCTA function enabled, this system does not work effectively
depending on the circumstances. The dr iver is responsible for checking the
safety around the vehicle by using his/her own eyes.
Overly relying on the system could lead to an unforeseen accident, resulting in
serious injury or death.
RAIZE_OM_General_BZ358E.book 212 ページ ２０２２年５月１７日　火曜日　午後１時５９分

2134-5. Using the driving support systems
RAIZE_OM_General_BZ358E
Driving
4
How to set up
Go to the “Settings” menu on the TFT color multi-information display, you
can change the settings of BSM function/RCTA function ON (enabled)/OFF
(disabled). (➞P. 109)
⬛Visibility of the outside rear view mirror indicators
⚫It may be difficult to see if the outsid e rear view mirror indicators are lit or
flashing in the following cases:
⦁ Under strong sunlight
⦁ The outside rear view mirrors are covered with ice or snow
⬛Buzzers
⚫It may be difficult to hear the buzzers if there is a loud noise around, such as
high volume audio.
⬛When the TFT color multi-information display shows “BSM Radar Blocked
Temporarily Unavailable”
It is possible that the rear bumper near the sensors is covered with ice, snow,
or mud. If you remove the ice, snow, or mud covering the rear bumper near
the sensors, the function will start working normally again.
⬛When the TFT color multi-information display shows “BSM Temporary
Unavailable”
If you use the function in an extremely hot or cold environment or if the bat-
tery voltage is lower or higher than th e specified level, the system operation
will be temporarily stopped. If the BSM OFF indicator or the RCTA OFF indicator
remains lit for a long time, have the vehi cle inspected at your Toyota dealer.
⬛When the TFT color multi-information display shows “BSM Malfunction
Visit Your Dealer”
It is possible that the sensors have failed or their positions or orientations are
off. Have the vehicle inspec ted at your Toyota dealer.
⬛Customizations
The BSM and RCTA settings can be changed.
(List of customizable features: ➞ P. 430)
(The settings can be changed from the setup screen of the TFT color multi-
information display: ➞ P. 104)
RAIZE_OM_General_BZ358E.book 213 ページ ２０２２年５月１７日　火曜日　午後１時５９分

2154-5. Using the driving support systems
RAIZE_OM_General_BZ358E
Driving
4
BSM function
The BSM function uses the radar sensors to detect vehicles traveling in
the next lane as described below and notifies the driver of the vehicles’
presence with the outside rear view mirror indicators and buzzers.
a A vehicle traveling in the area not re flected in the outside rear view mir-
rors (blind spot area)
b Vehicles rapidly approaching from behind into the area not reflected in
the outside rear view mirrors (blind spot area)
Detection range of the BSM function
The function detects a vehicle that has entered the area specified below.
a For both sides of the vehicle, an ar ea of approx. 3.5 m (11.5 ft.) from
approx. 0.5 m (1.6 ft.) away from the side surface
The function does not detect an area of a pprox. 0.5 m (1.6 ft.) from the side surface
of the vehicle toward the outside.
b Area approx. 1 m (3.3 ft.) ahead of the rear bumper
c Area approx. 3 m (9.8 ft.) behind the rear bumper
1
2
KBRO460503E
1
234
KBRO460504
RAIZE_OM_General_BZ358E.book 215 ページ ２０２２年５月１７日　火曜日　午後１時５９分

2184-5. Using the driving support systems
RAIZE_OM_General_BZ358E
⦁When driving up and down on a series of steep slopes or driving on
dented areas of a road
⦁ When driving through a sharp curve or continuous curves, or driving in an
area with ups and downs
⦁ While the tires are slipping (spinning)
⦁ When there is not enough distance between your vehicle and the follow-
ing vehicle
⦁ When the vehicle has accessories such as a bicycle carrier installed in the
rear side
⦁ When the vehicle is causing rain or snow to whirl up behind
RCTA function
⬛Activation of the RCTA function
The RCTA function uses the radar sens ors to detect vehicles approaching
from the right or left rear of your ve hicle and notifies the driver of the vehi-
cles’ presence with the outside rear view mirror indicators and buzzers.
a Approaching vehicle
b Detection range of approaching vehicles
⬛Detection range of the RCTA function
The function detects a vehicle that has entered the area specified below.
1
22
1
KBRO460505
11
KBRO460506
RAIZE_OM_General_BZ358E.book 218 ページ ２０２２年５月１７日　火曜日　午後１時５９分

2194-5. Using the driving support systems
RAIZE_OM_General_BZ358E
Driving
4
For the vehicle traveling fast, the warning buzzer will sound at a position
further away from the vehicle.
⬛Activation conditions of the RCTA function
The RCTA function will be activated when all of the following conditions are sat-
isfied:
⚫In the TFT color multi-info rmation display settings (➞P. 109), “RCTA” is set to
“ON”
⚫When the shift lever is set to R
⚫When the RCTA OFF indicator is off
⚫When your vehicle’s speed is approx. 8 km/h (5 mph) or less
⚫When the approaching vehicle’s speed is approx. between 8 and 28 km/h (5
and 18 mph)
⬛Situations where the RCTA function may not work properly
The RCTA function may not detect vehicles that fit the following description or
non-vehicle objects:
⚫A vehicle approaching from directly behind
⚫A vehicle backing up from the parking spot next to your vehicle
⚫Vehicles that cannot be detected by
the sensors due to obstacles
⚫Still objects such as guardrails, walls, road signs, parked vehicles, and so on
⚫Small motorcycles, bicycles, pedestrians, and so on
⚫Vehicles driving away from your vehicle
⚫A vehicle approaching from the parki ng spot next to your vehicle
⚫A vehicle approaching at high speed
Approaching vehicle’s speedaWarning distance (approximate)
Approx. 28 km/h (18 mph) (fast)Approx. 20 m (65.6 ft.)
Approx. 8 km/h (5 mph) (slow)Approx. 5.5m (18.0 ft.)
KBRO460507
RAIZE_OM_General_BZ358E.book 219 ページ ２０２２年５月１７日　火曜日　午後１時５９分