176
Practical information
Do not persist but introduce a Diesel type 
filler nozzle.
It is still possible to use a fuel can to fill 
the tank slowly.
In order to ensure a good flow of fuel, do 
not place the nozzle of the fuel can in direct 
contact with the flap of the misfuel prevention 
device.
Travelling abroad
As Diesel fuel pump nozzles may be 
different in other countries, the presence 
of the misfuel prevention device may make 
refuelling impossible.
Before travelling abroad, it is advisable to 
check with a PEUGEOT dealer if the vehicle 
is suitable for the distribution equipment of the 
countries visited.
Charging system 
(Electric)
400 V electrical system
The electric drive system, which operates at a 
voltage of approximately 400   V, is identified by 
orange cables and its components are marked 
with this symbol:
 
 
An electric vehicle’s power train can  become hot during use and after 
switching off the ignition.
Comply with the warning messages shown 
on the labels, particularly inside the charging 
flap.
High voltage system voltage is 
dangerous and can cause burns or other 
injuries or even fatal electric shock.
Since damage to high voltage components is 
not visible, PEUGEOT recommends that you:
–
 
Never touch the components, damaged 
or not, and never let your jewelry or other 
metallic objects come into contact with these 
components.
–
 
Never work on the orange high voltage 
cables or on any other high voltage 
component marked with the Electric risk label. 
Any intervention on the high voltage system 
must be carried out by qualified persons in 
workshops qualified and approved to carry 
out this type of work.
–
 
Never damage, modify or remove the 
orange high voltage cables or disconnect 
them from the high voltage network.
– Never open, modify or remove the cover of 
the traction battery .
–
 
Never work with cutting and forming 
tools or heat sources near high voltage 
components and cables.
In case of low level of fluid in the cooling 
tank, the refilling shall only be performed in a 
qualified and trained workshop to verify that 
the leakage is not in the traction battery
.
Any intervention on the high voltage system 
must be carried out by qualified persons in 
workshops qualified and approved to carry 
out this type of work.
Damage to the vehicle or the traction battery 
could result in the leakage of toxic gases or 
fluids either immediately or later. PEUGEOT 
recommends that you:
–
 
Always inform the fire and emergency 
services in the event of an incident, warning 
that the vehicle is equipped with a traction 
battery
.
–
 
Never touch the liquids leaking from the 
traction battery
.
–
 
Do not inhale the gases emitted by the 
traction battery which are toxic.
–
 
Move away from the vehicle in the event of 
incident or accident, the gases emitted being 
flammable and could cause a fire.
    CarM an uals 2 .c o m  
212
In the event of a breakdown
Model with halogen 
headlamps
 
 
1.Sidelamps (W5W-5W)
2. Main beam headlamps (H1-55W)
3. Dipped beam headlamps (H7-55W)
4. Daytime running lamps (W21W LL-21W)
5. Direction indicators (PY21W-21W amber)
Model with Xenon 
headlamps
 
 
1.Main beam headlamps (H1-55W)
2. Dipped beam headlamps (D8S-25W)
3. Direction indicators (PY21W-21W amber)
Be aware of the zone behind the right 
lamp (vehicle direction), which may be 
hot with a risk of burning (degassing hoses).
Accessing the bulbs 
 
► Press the upper clip on the cover then tilt it 
backwards to remove it.
Dipped beam headlamps 
 
► Press the lower clip on the connector and 
remove the assembly of connector and bulb.
►
 
Pull out the bulb and replace it.
When refitting the connector and bulb in 
the lamp unit, correctly position the 
assembly in its housing until it clicks into 
place.
Do not touch the Xenon lamps (D8S) 
– risk of electrocution!
If you need to replace this type of bulb, 
you must contact a PEUGEOT dealer or a 
qualified workshop.
Daytime running lamps 
 
► Press the two side clips on the connector and 
remove the assembly of connector and bulb.
►
 
Pull out the bulb and replace it.
Sidelamps 
 
► Press the two side clips on the connector and 
remove the assembly of connector and bulb.
►
 
Pull out the bulb and replace it.  CarM an uals 2 .c o m