2023 PEUGEOT EXPERT spare wheel

208
In the event of a breakdown
2.Jack.
Used to raise the vehicle.
3. Wheel bolt cover/wheel trim removal tool.
Depending on the vehicle's equipment, this is
used to remove the wheel bolt covers on alloy
wheels or the wheel trim on steel wheels.
4. Socket for "anti-theft" wheel bolts.
Used to adapt the wheelbrace to the special
"anti-theft" bolts.
5. Towing eye.
For more information on Towing, please
refer to the corresponding section.
The jack must only be used to change a wheel with a damaged or punctured tyre.
Do not use any jack other than the one
supplied with the vehicle.
If the vehicle does not have its original jack,
contact a PEUGEOT dealer or a qualified
workshop to obtain the one that was intended
by the manufacturer.
The jack meets European standards, as
defined in the Machinery Directive 2006/42/
CE.
The jack does not require any maintenance.
Accessing the spare wheel
► Access to the spare wheel is from the rear .
► Depending on version, open the side-hinged
doors or the tailgate.
To avoid any unwanted opening of the electric side door(s), deactivate the
Hands-Free Tailgate Access function in the
vehicle configuration menu.
For more information on the Hands-free
sliding side door , refer to the corresponding
section.


► If the vehicle is fitted with a towbar , raise
the rear of the vehicle using the jack (must be
at jacking point B) to allow sufficient space to
remove the spare wheel.
Remove the spare wheel from the
carrier


► Access the carrier bolt, located on the rear
door sill. ►

Slacken the bolt using the wheelbrace (about
14 turns) until the carrier is low enough to allow
the carrier hook to be disengaged.


► Release the carrier from the hook, take the
spare wheel and place it next to the wheel to be
changed.
Refit the spare wheel in the carrier

► Position the wheel facing the carrier . CarM an uals 2 .c o m

209
In the event of a breakdown
8► Progressively return the wheel to the carrier
by pushing alternately at the left and right until it
is clear of the hook fixing area.
►

Engage the carrier on the hook, then tighten
the bolt using the wheelbrace

until the bolt is fully
tightened.
Tyre in the carrier
You can change the size of the tyre on the spare
wheel by following the instructions below.
Original
tyre size Standard Long
215/65 R16 Placing a 225 wheel in the carrier is prohibited. There is no
restriction.
215/60 R17
215/60 R17
M&S
225/55 R17 Placing a 215 wheel in the
carrier is not
recommended (risk of noise).
A punctured tyre of size 215 or 225 can be placed in the carrier.
Removing a wheel
Parking the vehicle
Immobilise the vehicle where it does
not obstruct traffic: the ground must be level,
stable and non-slippery.
With a manual gearbox, engage first gear
then switch off the ignition to block the
wheels.
With an automatic gearbox, place the gear
selector in position P then switch off the
ignition to block the wheels.
With a drive selector, place the gear selector
in position P then switch off the ignition to
block the wheels.
Apply the parking brake, unless it is
programmed to automatic mode (for an
electric parking brake), and check that the
indicator lamp lights up on
the instrument
panel.
Ensure that the occupants have left the
vehicle and are located in a safe place.
Never go underneath a vehicle raised using a
jack; use an axle stand.
With an electric parking brake, place a chock
against the wheel diagonally opposite to the
one being replaced.


► With a steel wheel, remove the bolt cover
using tool 3
or the wheel trim by hand.
►

With an alloy wheel, remove the cover from
each of the bolts using tool 3

.
►

If the vehicle is so equipped, fit security bolt
socket

4 to wheelbrace 1 to slacken the security
bolt.
►

Slacken
(without removing) the other wheel
bolts using just wheelbrace 1.


► Place the foot of the jack on the ground and
ensure that it is directly below the A
or B jacking
point provided on the underbody, whichever is
closest to the wheel to be changed.


CarM an uals 2 .c o m

210
In the event of a breakdown

► Use the knob to extend the jack 2 until its
head comes into contact with jacking point A or
B, whichever is used; contact surface A or B on
the vehicle must be correctly engaged with the
central part of the head of the jack.
►

Raise the vehicle until there is sufficient
space between the wheel and the ground, to
then easily fit the spare (not punctured) wheel.
Risk of injury!
Ensure that the jack is stable. If the
ground is slippery or loose, the jack may slip
or collapse.
Ensure that the jack is positioned strictly at
one of the jacking points A or B under the
vehicle, making sure that the vehicle's contact
surface is correctly centred on the head of the
jack. Otherwise, there is a risk of damage to
the vehicle and/or of the jack collapsing.


► Remove the bolts and store them in a clean
place.
►

Remove the wheel.
Fitting the wheel

► Fit the wheel on the hub.
► Screw in the bolts by hand as far as possible.
►

If fitted to your vehicle,
pre-tighten the anti-
theft bolt using the wheelbrace 1 fitted with the
anti-theft socket 4. ►

Pre-tighten
the other bolts using the
wheelbrace
1
only.


► Lower the vehicle again fully
.
► Fold jack 2 and remove it.


► If fitted to your vehicle, tighten the anti-theft
bolt using the wheelbrace 1 fitted with the anti-
theft socket
4.
►

T
ighten the other bolts using the
wheelbrace

1
only.
►

Stow the tools in the tool box. CarM an uals 2 .c o m

2 11
In the event of a breakdown
8Fitting a steel or "space-saver" type
spare wheel
If the vehicle is fitted with alloy wheels, the
washers A do not make contact with the steel
or "space-saver" type spare wheel. The wheel
is held in place by the conical contact surface
B of each bolt.
After changing a wheel
Stow the punctured wheel in the carrier.
Go promptly to a PEUGEOT dealer or a
qualified workshop.
Have the punctured tyre examined. After
inspection, the technician will advise you on
whether the tyre can be repaired or if it must
be replaced.
Some driving aid functions should be
disabled, e.g. the Active Safety Brake.
If your vehicle has tyre under-inflation
detection, check the tyre pressures and
reinitialise the system.
For more information on Tyre under-inflation
detection, refer to the corresponding section.
Tyre under-inflation detection
The steel spare wheel does not have a
sensor.
Wheel with wheel trim
When refitting the wheel, refit the wheel
trim, starting by aligning the cutout with the
valve and then pushing the trim into place all
round its edge with the palm of your hand.
Changing a bulb
In some weather conditions (e.g. low
temperature or humidity), misting on the
internal surface of the glass of the headlamps
and rear lamps is normal, and will disappear
after the lamps have been on for a few
minutes.
The headlamps have polycarbonate lenses with a protective coating:
–

Do not clean them with a dry or abrasive
cloth, nor with detergent or solvent
products.
–


Use a sponge and soapy water or a pH
neutral product.
–


When using a high-pressure washer on
persistent marks, do not keep the lance
directed towards the headlamps, lamps or
their edges for too long, so as not to damage
their protective coating and seals.
Changing a bulb must only be done with
the ignition off and after the headlamp /
lamp has been switched off for several
minutes - risk of serious burns!
Do not touch the bulb directly with your
fingers; use a lint-free cloth.
It is essential only to use anti-ultraviolet
(UV) type bulbs, so as not to damage the
headlamp.
Always replace a failed bulb with a new bulb
of the same type and specification. To avoid
lighting imbalance, replace the bulbs in pairs.
Halogen bulbs (Hx)
To ensure good quality lighting, check
that the bulb is correctly positioned in its
housing.
Opening the bonnet/Accessing the
bulbs
Proceed with caution when the engine is hot -
risk of burns!
Take care with objects or clothing that could
be caught in the blades of the cooling fan -
risk of strangulation!
After changing a bulb
To refit, carry out the operations in
reverse order to removal.
Close the protective cover very carefully to
guarantee the sealing of the lamps. CarM an uals 2 .c o m

285
Alphabetical index
A
ABS 100
Accelerated charging unit (Wallbox)
179
Accessories

97
Access to the 3rd row

57, 59
Access to the spare wheel

208
Active Safety Brake

162, 164
AdBlue®

20, 196
AdBlue® tank

197
Additive, Diesel

193–194
Adjusting head restraints

49
Adjusting seat

48–49
Adjusting the air distribution

79–80
Adjusting the air flow

79–80
Adjusting the date

28, 255, 277
Adjusting the height and reach
of the steering wheel

51
Adjusting the lumbar support

48
Adjusting the seat angle

48–49
Adjusting the seat belt height

105
Adjusting the temperature

79–80
Adjusting the time

28, 254, 278
Advanced Grip Control

102
Advice on care and maintenance

177, 199
Advice on driving

7, 132–133
Airbags

107–109, 111
Airbags, curtain

108–109
Airbags, front

107, 109, 112
Airbags, lateral

108–109
Air conditioning

77, 79, 79–80, 82
Air conditioning, dual-zone

81
Air conditioning, dual-zone automatic 79–80
Air conditioning, manual
78–79, 81
Air intake

79–81
Air vents

77
Alarm

45–46
Anti-lock braking system (ABS)

100
Anti-pinch

74
Antitheft / Immobiliser

30
Applications

269
Area, loading

72
Armrest, front

50
Assistance call

98
Assistance, emergency braking

100, 163
Audio streaming (Bluetooth)

238, 250, 273
B
Battery, 12 V 187, 194, 216–219
Battery, ancillaries
216
Battery, charging

218–219
Battery, remote control

36, 84
Bench seat, heated

50
Bench seat, one-piece, fixed

57–58
Blind, panoramic roof

74
Blind spot monitoring

167
Blind spot monitoring system

168
Blinds, side

73
BlueHDi

20, 193, 202
Bluetooth (hands-free)

238–239, 252, 274
Bluetooth (telephone)

252–253, 274–275
Bodywork

200
Bonnet 190–191
Boot
44
Boot lid

33–34
Brake discs

195
Brake lamps

214, 216
Brakes

195
Braking

146
Braking assistance system

100
Braking, automatic emergency

162, 164
Braking, dynamic emergency

139–140
Brightness

254
Bulbs

2 11
Bulbs (changing)

211, 214
C
Cable, audio 272
Cable, Jack
272
Capacity, fuel tank

174–175
Cap, fuel filler

174–175
Care of the bodywork

200
CD

237
CD, MP3

237
Central locking

29, 33, 37
Changing a bulb

211, 214, 216
Changing a bulb (side-hinged doors)

214
Changing a fuse

216
Changing a wheel

207
Changing a wiper blade

95
Changing the remote control battery

36
Changing to free-wheeling

198, 220 CarM an uals 2 .c o m

291
Alphabetical index
Telephone 238–241, 252–253, 274–276
Telephone, Bluetooth with
voice recognition

241
Temperature, coolant

19–20
Thermal comfort consumption indicator
(Electric)

23
Thermal comfort equipment

23
Third brake lamp

214
Time (setting)

28, 254, 278
TMC (Traffic info)

265
Tool box

203
Tools

204, 207
Topping-up AdBlue®

197
Total distance recorder

23
Touch screen

26–27, 85
Towbar

102, 188
Towed loads

223–224, 227
Towing

220
Towing another vehicle

221–222
Towing eye

221
Towing the vehicle

220
Traction battery charge

180
Traction battery
(Electric)

22, 27, 176–177, 227
Traction control (ASR)

100–101, 103
Traffic information (TA)

234
Traffic information (TMC)

265
Trailer

102, 188
Trailer stability assist (TSA)

102
Trajectory control systems

100
Triangle, warning

202
Trip computer

24–25
Tyres

195, 231Tyre under-inflation
detection
148–149, 207, 211
U
Under-inflation (detection) 148
Unlocking
29–33
Unlocking from the inside

37
Unlocking, selective

31–33
Unlocking the doors

37–38
Unlocking, total

31–33
Updating the date

28, 255, 277
Updating the time

28, 254, 278
USB

236, 249, 251, 268, 272
V
Vehicle data recording and privacy 282
Ventilation
77–79, 83–84
Video

273
Vision, 180° rear

172
Visiopark 1

170
Voice commands

260–263
W
Wallbox (Electric) 179
Warning and indicator lamps
12
Warning lamp, driver's seat belt
not fastened

106
Warning lamps 12
Warning lamp, seat belts
106
Warnings and indicators

12
Washing

151
Washing (advice)

177, 199–200
Weights

223–224, 227
Wheel, spare

149, 195, 207–208, 211
Window, sliding side

73
Windows, rear

73
Windscreen, athermic

53
Windscreen zones for toll/car park cards

53
Wiper blades (changing)

95
Wiper, rear

94–95
Wipers

93–94
Wipers, automatic rain sensitive

94
Wipers, windscreen

93–94 CarM an uals 2 .c o m

Vehicle care 17
Vehicle care
Vehicle checks ............................. 17
Fuel cell system coolant ............17
Engine coolant ........................... 17
Electrical system ..........................18
Fuses ......................................... 18
Engine compartment fuse box ...19
Vehicle tools ................................ 20
Tools .......................................... 20
Wheels and tyres .........................21
Spare wheel .............................. 21
Jump starting ............................... 21 Vehicle checks
Fuel cell system coolant Coolant level Caution
The coolant reservoir may contain
traces of hydrogen which is
normal.
Using the wrong coolant can
cause
severe damages to the fuel
cell system. Only trained service
personnel are allowed to open the
coolant reservoir and to top up
coolant. Caution
A too low coolant level can cause
damage to the fuel cell system. If the cooling system is cold, the
coolant level should be above the
MIN mark. If the cooling level is too
low, seek the assistance of a
workshop.
Engine coolant
The factory filled coolant provides
freeze protection down to approx.
-37 °C

. Caution
Only use approved antifreeze.CarM an uals 2 .c o m

20 Vehicle care
No. Circuit
5 Fuel cell propulsion system
controller
6 H2 sensors
7 Main fuse
8 High temperature pump
9 Relays / RDI sensor / Refuel
button After having changed defective fuses,
close the fuse box cover and lock it.
If the fuse box cover is not closed
correctly, malfunction may occur. Vehicle tools
Tools The tools are located in the load
compartment. Vehicles with spare wheel
● Jack (1)
●
Wheel wrench (2)
● Towing eye (3)
● Wheel bolt cover remover (4)
● Chock (5)
● Adapter for the locking wheel nuts (6)
● Jack base (7)
Vehicles without spare wheel The bag contains the tyre repair kit
and is located behind the driver's
seat.CarM an uals 2 .c o m