2023 HYUNDAI IONIQ 6 overheating

1
1-29
E1Control pilot
communication -Vehicle communication
error
E2 Leakage - Current leakage
E3 - Charger error
E4 Plug
temperature -
Plug overtemperature
warning
E5 - Plug temperature failure
E6 - Charger error
E7 Overcurrent -Charging overcurrent
warning
E8 Internal
temperature - Charger overheating
E9 - Charger error
F1 Relay fusion - Charger error
F2 Ground
Monitoring/ Interrupt - Poor grounding of outlet
F3 Switched mode
power supply power failure -
Switched mode power
supply error (voltage
failure)
F4 -Switched mode power
supply error (abnormal
voltage)
F5 Control Pilot
voltage error -
Control Pilot (-) voltage
error
F6 -Control Pilot (+) voltage
error
F7 Temperature
sensor error -
Plug temperature sensor
error
F8 -PCB internal temperature
sensor error
IconNameColorDescription
A
Hyundai_CE_en_US.book Page 29

Introduction/Getting Started with Your Electric Vehicle
1-48
• The V2L discharging mode is blocked automatically in the event of overheating. When the discharging mode is blocked, check whether the V2L connector or power plug is
contaminated, worn, corroded or broken.
- If the temperature falls to a proper level after it is left unattended, you can use it again.
- If overheating repeats when using a certain electric device, do not use the electric device.
• Do not connect more than two extension cords or multi-outlet. Also, when using the extension cable, ensure that the cable is not twisted. Heat from the overlapped cable
may cause fire.
• Do not hang home appliances on the wire.
• Do not use if the sheath of home appliance cables is damaged or broken.
• Fully insert the power plug when connecting it to the power.
• Only use qualified power plug with ground connection that meets the standard. Do not use worn, corroded, or broken power plug or improper power plug that does not meet
the standard.

Using Electricity Outside the Vehicle
Before using V2L function, carefully read all the safety information and precautions on
the “Safety Precautions When Using the V2L Function” section and follow the
instructions.
Follow the instructions below to connect the V2L connector to the charging inlet on the
vehicle and supply power to an electronic product.
1. Open the cover of the V2L connector.
2. Close the cover after connecting the plug of an electronic product to the power outlet of the connector.
WARNING Some types of plugs may not fit into the outlet cover of the V2L connector, causing
incomplete closing of the cover. Do not use the V2L connector on a rainy or snowy day
if the outlet cover is not completely closed. There is a risk of fire and/or injury.

3. Open the connection terminal protection cap of the connector with the open switch pressed.
4. Open the charging door and connect the V2L connector to the charging inlet on the vehicle.
• Connect the V2L connector to the charging inlet within 60 seconds after opening the charging door.
5. Press the power switch of the V2L connector. • The power is supplied and the indicator on the V2L connector is turned on.
Hyundai_CE_en_US.book Page 48

1
1-51
- For more information about the discharging limit, refer to the “Setting a Battery Discharging Limit When Using Vehicle to Load (V2L)” section in this chapter.
- For more information about warnings, refer to the “Checking the warning and indicator lights” section in this chapter.

Solving V2L Problems
If a problem occurs while using the V2L function, the V2L stops and a related messages
appears on the instrument cluster.
Check the cause of the message and take an appropriate measure referring to the table
below.
MessageCauseMeasure
V2L finished. Defined
charge level reached The high voltage battery level
reaches the discharging limit
set level. To use the V2L continuously,
make the discharging limit set
level lower than the present
battery level. (For more
information, refer to the
“Setting a Battery Discharging
Limit When Using Vehicle to
Load (V2L)”.)
Energy consumption
too high. V2L
cancelled An electrical appliance that
exceeds the maximum power
output the vehicle can supply is
connected. Check the total power
consumption of the electrical
appliance and replace it a
product within the V2L
maximum power output.
V2L conditions not
met V2L is stopped for the following
reasons:
• V2L connector switch off
• V2L connector overheating
• Opening the charging door
while using the V2L indoor
outlet Make sure there are no
problems with the V2L
connector and the vehicle
indoor outlet.
7-
GJOJTIFE
%FGJOFE
DIBSHF MFWFM
SFBDIFE
&OFSHZ
DPOTVNQUJPO
UPP IJHI
7-
DBODFMMFE
7-
DPOEJUJPOT OPU
NFU
Hyundai_CE_en_US.book Page 51

6
6-13
Check shifter dial
B6013804
This message is displayed when there is a
malfunction with the rotary shifter.
Have the vehicle inspected by an
authorized HYUNDAI dealer.
Check P button
B6013805
This message is displayed when there is a
problem with the P button.
Have the vehicle inspected by an
authorized HYUNDAI dealer.
Rotary shifter stuck
B6013806
This message is displayed when the rotary
shifter does not return back to it’s normal
position.
Have the vehicle inspected by an
authorized HYUNDAI dealer.
Good Driving Practices
• Never shift the gear from P (Park) or N (Neutral) to any other position with the
accelerator pedal depressed.
• Never shift the gear into P (Park) when the vehicle is in moving. Completely
stop before shifting into R (Reverse) or
D (Drive).
• Do not shift the gear to N (Neutral) when driving. If the gear is shifted to N
(Neutral) while driving. Doing so may
increase the risk of an accident.
Also, shift the gear back to D (Drive)
while the vehicle is moving may
severely damage the gear.
• Never attempt to select a gear that is opposite the direction of the vehicle
motion. Check the gear position before
driving. Stop the vehicle before shifting
to the desired gear. The vehicle may
turn off, causing a collision.
• Do not drive with your foot resting on the brake pedal. Even light, but
consistent pedal pressure can result in
the brakes overheating, brake wear and
possibly even brake failure.
$IFDL
TIJGUFS
EJBM
$IFDL
1
CVUUPO
3PUBSZ
TIJGUFS
TUVDL
Hyundai_CE_en_US.book Page 13

6
6-35
BAS operation
• When the vehicle speed is more than 18 mph (30 km/h) and the ABS control is
not entered.
• When the brake pedal is depressed strongly over a certain level.
• When the friction of the road surface is above a certain level.
BAS operation off
• The vehicle speed is below 6 mph (10 km/h).
• The brake pedal is depressed over a certain conditions.
• The friction of the road surface is below a certain level.
WARNING The system may not operate depending
on driver's driving habit, the degree to
which the brake pedal is depressed and
the road surface condition.

Good Braking Practices
WARNING Whenever leaving the vehicle or parking,
always come to a complete stop and
continue to depress the brake pedal. Shift
the gear to the P (Park) position, then
apply the parking brake, and press the
Start/Stop button to the OFF position.
Vehicles parked with the parking brake
not applied or not fully engaged may roll
inadvertently and may cause injury to the
driver and others. ALWAYS apply the
parking brake before exiting the vehicle.

Be aware of wet brakes. The brakes may
get wet if the vehicle is driven through
standing water or if it is washed. Your
vehicle will not stop as quickly if the brakes are wet. Wet brakes may cause the
vehicle to pull to one side.
To dry the brakes, apply the brakes lightly
until the braking action returns to normal.
If the braking action does not return to
normal, stop as soon as it is safe to do so
and call an authorized HYUNDAI dealer
for assistance.
DO NOT drive with your foot resting on
the brake pedal. Even light, but constant
pedal pressure can result in the brakes
overheating, brake wear, and possibly
even brake failure.
If a tire goes flat while you are driving,
apply the brakes gently and keep the
vehicle pointed straight ahead while you
slow down. When you are moving slowly
enough for it to be safe to do so, pull off
the road and stop in a safe location.
Keep your foot firmly on the brake pedal
when the vehicle is stopped to prevent
the vehicle from rolling forward.
Hyundai_CE_en_US.book Page 35

Driving Your Vehicle
6-46
Rocking the Vehicle
If it is necessary to rock the vehicle to free
it from snow, sand, or mud, first turn the
steering wheel right and left to clear the
area around your front wheels. Then, shift
back and forth between R (Reverse) and a
forward gear.
Try to avoid spinning the wheels, and do
not race the vehicle.
To prevent gear wear, wait until the
wheels stop spinning before shifting
gears. Release the accelerator pedal
while shifting, and press lightly on the
accelerator pedal while the vehicle is in
gear. Slowly spinning the wheels in
forward and reverse directions causes a
rocking motion that may free the vehicle.
WARNING Always turn off the ESC system before
rocking the vehicle. If the vehicle is stuck
and excessive wheel spin occurs, the
temperature in the tires may increase
very quickly. If the tires become
damaged, a tire blow out or tire explosion
may occur - you and others may be
injured. Do not attempt this procedure if
people or objects are near the vehicle.
If you attempt to free the vehicle, the
vehicle may overheat quickly, possibly
causing a motor compartment fire or
other damage. Try to avoid spinning the
wheels as much as possible to prevent
overheating of the tires or the motor. DO
NOT allow the vehicle to spin the wheels
above 35 mph (56 km/h).
If you are still stuck after rocking the
vehicle a few times, have the vehicle
pulled out by a tow vehicle to avoid motor
overheating, possible damage to the
transmission, and tire damage. Refer to
the “Towing” section in chapter 8.

Smooth Cornering
Avoid braking or gear changing in
corners, especially when roads are wet.
Ideally, cornering should be taken under
gentle acceleration.
Driving at Night
Night driving presents more hazards than
driving in the daylight. Here are some
important tips to remember:
• Slow down and keep more distance between you and other vehicles, as it
may be more difficult to see at night,
especially in areas where there may not
be any street lights.
• Adjust your mirrors to reduce the glare from other drivers’ headlights.
• Keep your headlights clean and properly aimed. Dirty or improperly
aimed headlights will make it much
more difficult to see at night.
• Avoid staring directly at the headlights of oncoming vehicles. You could be
temporarily blinded, and it will take
several seconds for your eyes to
readjust to the darkness.
Driving in the Rain
Rain and wet roads can make driving
dangerous. When driving in the rain or on
slick pavement:
• Slow down and allow extra following distance. A heavy rainfall makes it
harder to see and increases the
distance needed to stop your vehicle.
• Turn OFF your Smart Cruise Control.
• Replace your windshield wiper blades when they show signs of streaking or
missing areas on the windshield.
• Make sure your tires have enough tread. If your tires do not have enough
tread, making a quick stop on wet
pavement may cause a skid and
possibly lead to a collision. Refer to the
Hyundai_CE_en_US.book Page 46