2023 HYUNDAI IONIQ 6 tow
[x] Cancel search: towPage 172 of 582
Instrument Cluster
4-22
Stop vehicle and check power
supply
This warning message is displayed when
a failure occurs in the power supply
system.
In this case, park the vehicle in a safe
location and tow your vehicle to the
nearest authorized HYUNDAI dealer and
have the vehicle inspected.
Check electric vehicle system
This warning message is displayed when
there is a problem with the electric
vehicle control system.
Refrain from driving when the warning
message is displayed.
In this case, have the vehicle inspected by
an authorized HYUNDAI dealer.
Check active air flap system
OOSEV040510L
This warning message is displayed in the
following situations:
• There is a malfunction with the actuator flap
• There is a malfunction with the actuator air flap controller
• The air flap does not open
When all of the above conditions are
fixed, the warning will disappear.
Check virtual engine sound system
OOSEV040512L
This message is displayed when there is a
problem with the Virtual Engine Sound
System (VESS).
In this case, have the vehicle inspected by
an authorized HYUNDAI dealer.
$ I F D L " D U J W F
" J S ' M B Q 4 Z T U F N
$ I F D L 7 J S U V B M & O H J O F 4 P V O E 4 Z T U F N
Hyundai_CE_en_US.book Page 22
Page 187 of 582
5
5-9
circuit of the smart key to malfunction
which may not be covered under
warranty.
• Avoid dropping or throwing the smart key.
• Protect the smart key from extreme temperatures.
Loss of a smart key
A maximum of three smart keys can be
registered to a single vehicle. If you
happen to lose your smart key, it is
recommended that you should
immediately take the vehicle and
remaining keys to your authorized
HYUNDAI dealer or tow the vehicle, if
necessary.
Smart key precautions
The smart key may not work if any of the
following occur:
• The smart key is close to a radio transmitter such as a radio station or an
airport which can interfere with normal
operation of the transmitter.
• The smart key is near a mobile two way radio system or a mobile phone.
• Another vehicle’s smart key is being operated close to your vehicle.
• The smart key is near any normal electronic devices or credit cards.
If the smart key does not work correctly,
open and close the door with the
mechanical key. If you have a problem
with the smart key, contact an authorized
HYUNDAI dealer.
If the smart key is in close proximity to
your mobile phone, the signal could be
blocked by your mobile phone’s normal
operational signals. This is specifically
relevant when the phone is active such as
making and receiving calls, text
messaging, and/or sending/receiving
emails. When possible, avoid keeping the
smart key and your mobile phone in the same location such as pants or jacket
pocket in order to avoid interference
between the two devices.
Information Changes or modifications not expressly
approved by the party responsible for
compliance could void the user’s authority to
operate the equipment. If the keyless entry
system is inoperative due to changes or
modifications not expressly approved by the
party responsible for compliance, it will not be
covered by your manufacturer’s vehicle
warranty.
Information This device complies with Part 15 of the FCC
rules.
Operation is subject to the following three
conditions:
1. This device may not cause harmful
interference, and
2. This device must accept any interference received, including interference that may
cause undesired operation.
3. Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority
to operate the device.
NOTICE [ . H H S W K H V P D U W N H \ D Z D \ I U R P H O H F W U R P D J Q H W L F P D W H U L D O V W K D W E O R F N V
H O H F W U R P D J Q H W L F Z D Y H V W R W K H N H \
V X U I D F H
[ $ O Z D \ V K D Y H W K H V P D U W N H \ Z L W K \ R X Z K H Q O H D Y L Q J W K H Y H K L F O H , I W K H V P D U W
N H \ L V O H I W Q H D U W K H Y H K L F O H W K H Y H K L F O H
E D W W H U \ P D \ E H G L V F K D U J H G
Hyundai_CE_en_US.book Page 9
Page 201 of 582
5
5-23
• “Approach unlock” system is not operated continuously. Retry after a
certain period of time when all the
doors are closed.
Information • In cold and wet climates, door lock and door mechanisms may not work properly
due to freezing conditions.
• If the door is locked/unlocked multiple times in rapid succession with either the
vehicle key or door lock switch, the system
may stop operating temporarily in order to
protect the circuit and prevent damage to
system components.
• When washing the vehicle - Self vehicle washKeep the door locked with the outside
door handle closed.
To keep the door unlocked, push back the
outside door handle by hand. This
function prevents the door handle from
being damaged, and the door handle pops
out again when the unlock button is
pressed.
- Auto vehicle wash Keep the door locked with the outside
door handle closed.
If the smart key is not in the vehicle, turn
off the vehicle and stay the smart key
away at least 78 in. (2 m) from the vehicle
to prevent the outside door handle
operates.
if equipped
Digital key
For more information, refer to the
"Hyundai Digital Key" section in this
chapter to lock or unlock the door from
outside vehicle with digital key.
Pull the outside door handle to open the
door after unlocking the door. Push the
door to close.
Mechanical key
B5002903
B5002904
Turn the knob (2) of the mechanical key
after removing the key protector (1).
Press the front part (3) of the door handle
to pull out the rear part of the door
handle. While keep pressing the front part
of the door handle, insert the mechanical
key (4) to the lock.
To lock the door, turn the key toward the
front (left side) of the vehicle. To unlock,
turn the key toward the rear (right side) of
the vehicle.
NOTICE ' R Q R W D S S O \ H [ F H V V L Y H I R U F H R Q W K H G R R U
D Q G G R R U K D Q G O H , W P D \ G D P D J H W K H G R R U
D Q G G R R U K D Q G O H
7 K H P H F K D Q L F D O N H \ R Q O \ O R F N V X Q O R F N V
W K H G U L Y H UT V G R R U K D Q G O H ) R U P R U H
L Q I R U P D W L R Q U H I H U W R W K H , Q F D V H R I D Q
H P H U J H Q F \ V H F W L R Q L Q W K L V F K D S W H U
Hyundai_CE_en_US.book Page 23
Page 211 of 582
5
5-33
• A click noise may be heard from the MDPS relay after the Start/Stop button is in the ON
or OFF position.
• Motor noise may be heard when the vehicle is at a stop or at a low driving speed.
• When you operate the steering wheel in low temperatures, abnormal noise may occur. If
the temperature rises, the noise will
disappear. This is a normal condition.
• When an error is detected from MDPS, the steering effort assist function will not be
activated in order to prevent fatal accidents.
Instrument cluster warning lights may be on
or the steering effort may be high. If these
symptoms occur, drive the vehicle to a safe
area as soon as it is safe to do so. Have the
system inspected by an authorized
HYUNDAI dealer as soon as possible.
Tilt/Telescopic Steering
When adjusting the steering wheel to a
comfortable position, adjust the steering
wheel so that it points toward your chest,
not toward your face. Make sure you can
see the instrument cluster warning lights
and gauges. After adjusting, push the
steering wheel both up and down to be
certain it is locked in position.
Always adjust the position of the steering
wheel before driving.
WARNING NEVER adjust the steering wheel while
driving. This may cause loss of vehicle
control resulting in an accident.
NOTICE : K L O H D G M X V W L Q J W K H V W H H U L Q J Z K H H O
K H L J K W S O H D V H G R Q R W S X V K R U S X O O L W K D U G
V L Q F H W K H I L [ W X U H F D Q E H G D P D J H G
Manual adjustment
B5006301
To adjust the steering wheel angle and
height:
1. Pull down the lock-release lever (1).
2. Adjust the steering wheel to the desired angle (2) and distance forward/back
(3).
3. Pull up the lock-release lever to lock the steering wheel in place.
Information Sometimes the lock-release lever may not
engage completely. Pull down on the
lock-release lever, readjust the steering wheel
again, and then pull back up on the
lock-release lever to lock the steering wheel in
place.
Horn
B5006501
To sound the horn, press the area
indicated by the horn symbol on your
2
13
2
Hyundai_CE_en_US.book Page 33
Page 214 of 582
Convenience Features
5-36
if equipped
Day/night rearview mirror
B5006901
Make this adjustment before you start
driving and while the day/night lever is in
the day position.
Pull the day/night lever towards you to
reduce glare from the headlights of the
vehicles behind you during night driving.
Remember that you lose some rearview
clarity in the night position.
if equipped
Electric Chromic Mirror (ECM)
B5006902[A] Indicator
Some vehicles come equipped with an
electrochromic mirror that helps control
glare while driving at night or under low
light driving conditions.
When the vehicle is running, the glare is
automatically controlled by the sensor
mounted in the rearview mirror. The
sensor detects the light level around the
vehicle, and automatically adjusts to control the headlight glare from vehicles
behind you.
Whenever the gear is shifted to R
(Reverse), the mirror will automatically go
to the brightest setting in order to
improve the driver’s view behind the
vehicle.
Electrochromic mirror (ECM) with
if equipped
HomeLink® system
Your vehicle may be equipped with a
Gentex Automatic-Dimming Mirror with
an Integrated HomeLink® Wireless
Control System.
During nighttime driving, this feature will
automatically detect and reduce rearview
mirror glare. The HomeLink® Universal
Transceiver allows you to activate your
garage door(s), electric gate, home
lighting, etc.
ONE1051261N(1) HomeLink Channel 1
(2) HomeLink Channel 2
(3) HomeLink Channel 3
(4) Garage Door Opener Status Indicator:
Closing or Closed
(5) HomeLink Operation Indicator
(6) Garage Door Opener Status Indicator: Opening or Opened
(7) HomeLink User Interface Indicator
Hyundai_CE_en_US.book Page 36
Page 246 of 582
Convenience Features
5-68
B5015603
Parking light ( )
The parking light, license plate light and
instrument panel lamp are turned ON.
B5015604
Headlight ( )
The headlight, parking light, license plate
light and instrument panel lamp are
turned ON.
Information The Start/Stop button must be in the ON
position to turn on the headlight.
High beam operation
B5015702
To turn on the high beam headlight, push
the lever away from you. The lever will
return to its original position.
The high beam indicator will light when
the headlight high beams are switched
on.
To turn off the high beam headlight, pull
the lever towards you. The low beams will
turn on.
B5015701
To flash the high beam headlight, pull the
lever towards you, then release the lever.
The high beams will remain ON as long as
you hold the lever towards you.
Hyundai_CE_en_US.book Page 68
Page 252 of 582
Convenience Features
5-74
if equipped
High Beam Assist (HBA)
B5016701
High Beam Assist automatically controls
the headlights between high beam and
low beam depending on the detected
ambient light, such as an oncoming
vehicle or leading vehicle.
Detecting sensor
B5016702(1) front view camera
The front view camera is used as a
detecting sensor to detect ambient light
and brightness while driving.
Refer to the illustration above for the
detailed location of the detecting sensor.
NOTICE [ $ O Z D \ V N H H S W K H I U R Q W Y L H Z F D P H U D L Q J R R G F R Q G L W L R Q W R P D L Q W D L Q R S W L P D O
S H U I R U P D Q F H R I + L J K % H D P $ V V L V W
[ ) R U P R U H L Q I R U P D W L R Q R Q W K H S U H F D X W L R Q V R I W K H I U R Q W Y L H Z F D P H U D U H I H U W R W K H U ) R U Z D U G
& R O O L V L R Q $ Y R L G D Q F H $ V V L V W ) & $ \fV
V H F W L R Q L Q F K D S W H U
High Beam Assist Settings
Setting features
ONE1051248L
With the Start/Stop button in the ON
position, select Setup > Vehicle > High
Beam Assist from the Settings menu to
turn on High Beam Assist and deselect to
turn off the function.
WARNING For your safety, change the Settings after
parking the vehicle at a safe location.
High Beam Assist Operation
Display and control
• After selecting 'High Beam Assist' in
the Settings menu, High Beam Assist
will operate by following the procedure
below.
- Place the headlight switch in the AUTO position and push the
headlight lever towards the
instrument cluster. The High Beam
Assist ( ) indicator light will
illuminate on the instrument cluster
1
Hyundai_CE_en_US.book Page 74
Page 253 of 582
5
5-75
and High Beam Assist will be
enabled.
- When High Beam Assist is enabled, high beam will turn on when vehicle
speed is above 25 mph (40 km/h).
When vehicle speed is below 15 mph
(25 km/h), high beam will turn off and
the High Beam Assist ( ) indicator
will be displayed in white on the
instrument cluster.
- The High Beam ( ) indicator light will illuminate on the instrument cluster
when high beam is on.
• When High Beam Assist is operating, if the headlight lever or switch is used,
High Beam Assist operates as follow:
- If the headlight lever is pulled towards you when the high beam is
off, the high beam will turn on
without High Beam Assist canceled.
When you let go of the headlight
lever, the lever will move to the
middle and the high beam will turn
off.
- If the headlight lever is pulled towards you when the high beam is
on by High Beam Assist, low beam
will turn on and the function will turn
off.
- If the headlight switch is placed from AUTO to another position
(headlight/position/off), High Beam
Assist will turn off and the
corresponding light will turn on.
• When High Beam Assist is operating, high beam switches to low beam if any
of the following conditions occur:
- When the headlight of an oncoming vehicle is detected.
- When the tail light of a vehicle in front is detected.
- When the headlight or tail light of a motorcycle or a bicycle is detected.
- When the surrounding ambient light is bright enough that high beams are
not required. - When streetlights or other lights are
detected.
Information The images and colors in the instrument
cluster may differ depending on the cluster
type or theme selected from the settings menu.
High Beam Assist Malfunction
and Limitations
High Beam Assist malfunction
OJK050059L
When High Beam Assist is not working
properly, the ‘Check High Beam Assist
system’ warning message will appear and
warning light will illuminate on the
instrument cluster. Have the function
inspected by an authorized HYUNDAI
dealer.
Limitations of High Beam Assist
High Beam Assist may not work properly
in the following situations:
• Light from an oncoming or front vehicle is not detected because of light
damage, or because it is hidden from
sight, etc.
• Headlight of an oncoming or front vehicle is covered with dust, snow or
water.
• A front vehicle’s headlights are off, but the fog lights are on, etc.
$ I F D L
) J H I # F B N " T T J T U T Z T U F N
Hyundai_CE_en_US.book Page 75