2023 HYUNDAI I20 brake light
[x] Cancel search: brake lightPage 506 of 649
Driver assistance system
7-160
OBC3070044R
1. Getting ready for exit
(1) With the engine turned on, depress
the brake pedal and shift the gear to
P (Park) or N (Neutral).
(2) Press and hold the Parking/View
(
) button to turn on Parking Assist.
A message will appear on the cluster
and the Parking Safety (
) button
indicator light will illuminate.
[ If the engine is turned on when the
gear is in N (Neutral), Exit mode
will be selected. Parking mode will
be selected automatically after the
vehicle has been driven.
[ Parking Assist is turned off whenever
the engine is restarted. Press the
Parking/View (
) button to turn use
Parking Assist again.
.
OBC3070106TU
2. Selecting exit mode and type
(1) Select exit mode by pressing the
Parking/View (
) button briefly.
Parking type will change whenever
the button is pressed.
/ H I W S D U D O O H O H [ L W
Page 522 of 649
8-7
08
i Information
Pb
An inappropriately disposed
battery can be harmful to the
environment and human
health. Dispose of the battery
according to your local law(s)
or regulations.
Jump starting procedure
1. Position the vehicles close enough
that the jumper cables will reach, but
do not allow the vehicles to touch.
2. Avoid fans or any moving parts in the
engine compartment at all times, even
when the vehicles are turned off.
3. Turn off all electrical devices such
as radios, lights, air conditioning,
etc. Put the vehicles in P (Park, for
automatic transmission/dual clutch
transmission vehicle) or neutral (for
manual transmission vehicle), and set
the parking brakes. Turn both vehicles
OFF.1VQA4001
4. Connect the jumper cables in
the exact sequence shown in the
illustration. First connect one jumper
cable to the red, positive (+) jumper
terminal of your vehicle (1).
5. Connect the other end of the jumper
cable to the red, positive (+) battery/
jumper terminal of the assisting
vehicle (2).
6. Connect the second jumper cable to
the black, negative (-) battery/ chassis
ground of the assisting vehicle (3).
7. Connect the other end of the second
jumper cable to the black, negative (-)
chassis ground of your vehicle (4).
Do not allow the jumper cables to
contact anything except the correct
battery or jumper terminals or the
correct ground. Do not lean over the
battery when making connections.
8. Start the engine of the assisting
vehicle and let it run at approximately
2,000rpm for a few minutes. Then
start your vehicle.
If your vehicle will not start after a
few attempts, it probably requires
servicing. In this event, please seek
qualified assistance. If the cause of your
battery discharging is not apparent, we
recommend that you have your vehicle
checked by a HYUNDAI authorised
repairer.
Page 530 of 649
8-15
08
If the indicators do not extinguish after
a few minutes, it is recommended to
contact the nearest authorised HYUNDAI
dealer.
Each wheel is equipped with a tyre
pressure sensor mounted inside the tyre
behind the valve stem (except for the
spare tyre). You must use TPMS specific
wheels. It is recommended that you
always have your tyres serviced by a
HYUNDAI authorised repairer.
You may not be able to identify a tyre
with low pressure by simply looking at it.
Always use a good quality tyre pressure
gauge to measure. Please note that a
tyre that is hot (from being driven) will
have a higher pressure measurement
than a tyre that is cold.
A cold tyre means the vehicle has been
sitting for 3 hours and driven for less
than 1 mile (1.6 km) in that 3 hour period.
Allow the tyre to cool before measuring
the inflation pressure. Always be sure
the tyre is cold before inflating to the
recommended pressure.
WARNING
[ The TPMS cannot alert you to severe
and sudden tyre damage caused by
external factors such as nails or road
debris.
[ If you feel any vehicle instability,
immediately take your foot off
the accelerator, apply the brakes
gradually with light force, and slowly
move to a safe position off the road.
WARNING
Tampering with, modifying, or disabling
the Tyre Pressure Monitoring System
(TPMS) components may interfere
with the system’s ability to warn the
driver of low tyre pressure conditions
and/or TPMS malfunctions. Tampering
with, modifying, or disabling the Tyre
Pressure Monitoring System (TPMS)
components may void the warranty for
that portion of the vehicle.
WARNING
[ Do not modify the vehicle; it may
interfere with the TPMS function.
[ The wheels on the market do not
have a TPMS sensor.
[ For your safety, we recommend that
you use parts for replacement from a
HYUNDAI authorised repairer.
[ If you use the wheels on the market,
use a TPMS sensor approved by a
HYUNDAI dealer or the equivalent
approved for your vehicle. If your
vehicle is not equipped with a TPMS
sensor or TPMS does not work
properly, you may fail the periodic
vehicle inspection conducted in your
country.
Page 567 of 649
9-8
Maintenance
Whilst operating your vehicle:
[ Note any changes in the sound of the
exhaust or any smell of exhaust fumes
in the vehicle.
[ Check for vibrations in the steering
wheel. Notice if there is any increased
steering effort or looseness in the
steering wheel, or change in its
straight-ahead position.
[ Notice if your vehicle constantly turns
slightly or “pulls” to one side when
travelling on smooth, level road.
[ When stopping, listen and check for
unusual sounds, pulling to one side,
increased brake pedal travel or “hard-
to-push” brake pedal.
[ If any slipping or changes in the
operation of your transmission occurs,
check the transmission fluid level.
[ Check the parking brake.
[ Check for fluid leaks under your
vehicle (water dripping from the air
conditioning system during or after
use is normal).
At least monthly:
[ Check coolant level in the engine
coolant reservoir.
[ Check the operation of all exterior
lights, including the stoplights, turn
signals and hazard warning flashers.
[ Check the inflation pressures of all
tyres including the spare for tyres that
are worn, show uneven wear, or are
damaged.
[ Check for loose wheel lug nuts.
At least twice a year:
(i.e., every Spring and Autumn)
[ Check radiator, heater and air
conditioning hoses for leaks or
damage.
[ Check windscreen washer spray and
wiper operation. Clean wiper blades
with a clean cloth dampened with
washer fluid.
[ Check headlight alignment.
[ Check muffler, exhaust pipes, shields
and clamps.
[ Check the seat belts for wear and
function.
At least once a year:
[ Clean body and door drain holes.
[ Lubricate door hinges and bonnet
hinges.
[ Lubricate door and bonnet locks and
latches.
[ Lubricate door rubber weather strips.
[ Lubricate door checker
[ Check the air conditioning system.
[ Inspect and lubricate automatic
transmission linkage and controls.
[ Clean the battery and terminals.
[ Check the brake fluid level.
Page 618 of 649
9-59
09
We recommend that you consult with a
HYUNDAI authorised repairer to replace
most vehicle light bulbs. It is difficult
to replace vehicle light bulbs because
other parts of the vehicle must be
removed before you can get to the bulb.
This is especially true for removing the
headlight assembly to get to the bulb(s).
Removing/installing the headlight
assembly can result in damage to the
vehicle.
WARNING
Prior to replacing a light, depress the
foot brake, move the shift lever into the
N (Neutral, for automatic transmission
vehicle) or neutral (for manual
transmission vehicle), apply the parking
brake, place the ignition switch in the
LOCK/OFF position, and take the key
with you when leaving the vehicle to
avoid sudden movement of the vehicle
and to prevent possible electric shock.
% H D Z D U H W K H E X O E V P D \ E H K R W D Q G P D \
burn your fingers.
NOTICE
% H V X U H W R U H S O D F H W K H E X U Q H G R X W E X O E
with one of the same wattage rating.
Otherwise, it may cause damage to the
fuse or electric wiring system.
i Information
7 K H K H D G O L J K W D Q G W D L O O D P S O H Q V H V F R X O G
D S S H D U I U R V W \ L I W K H Y H K L F O H L V Z D V K H G D I W H U
G U L Y L Q J R U W K H Y H K L F O H L V G U L Y H Q D W Q L J K W
L Q Z H W Z H D W K H U 7 K L V F R Q G L W L R Q L V F D X V H G
E \ W H P S H U D W X U H G L I I H U H Q F H E H W Z H H Q W K H
O D P S L Q V L G H D Q G R X W V L G H D Q G L W G R H V Q R W
L Q G L F D W H D S U R E O H P Z L W K \ R X U Y H K L F O H
: K H Q P R L V W X U H F R Q G H Q V H V L Q W K H O D P S
L W Z L O O E H U H P R Y H G D I W H U G U L Y L Q J Z L W K W K H
K H D G O L J K W R Q 7 K H U H P R Y D E O H O H Y H O P D \
G L I I H U G H S H Q G L Q J R Q O D P S V L ] H O D P S
S R V L W L R Q D Q G H Q Y L U R Q P H Q W D O F R Q G L W L R Q
+ R Z H Y H U L I P R L V W X U H L V Q R W U H P R Y H G Z H
U H F R P P H Q G W K D W \ R X U Y H K L F O H L V L Q V S H F W H G
E \ D + < 8 1 ' $ , D X W K R U L V H G U H S D L U H U
i Information (For Europe)
7 U D I I L F & K D Q J H
7 K H O R Z E H D P O L J K W G L V W U L E X W L R Q L V
D V \ P P H W U L F , I \ R X J R D E U R D G W R D F R X Q W U \
Z L W K R S S R V L W H W U D I I L F G L U H F W L R Q W K L V
D V \ P P H W U L F S D U W Z L O O G D ] ] O H R Q F R P L Q J F D U
G U L Y H U 7 R S U H Y H Q W G D ] ] O H ( & ( U H J X O D W L R Q
G H P D Q G V V H Y H U D O W H F K Q L F D O V R O X W L R Q V H [
D X W R P D W L F F K D Q J H V \ V W H P D G K H V L Y H V K H H W
G R Z Q D L P L Q J 7 K H V H K H D G O L J K W V D U H
G H V L J Q H G Q R W W R G D ] ] O H R S S R V L W H G U L Y H U V
6 R \ R X Q H H G Q R W F K D Q J H \ R X U K H D G O L J K W V
L Q D F R X Q W U \ Z L W K W K H R S S R V L W H W U D I I L F
G L U H F W L R Q
LIGHT BULBS
Page 639 of 649
9-80
Maintenance
NOTICE
If you park your vehicle near a stainless
steel sign or glass facade building, the
vehicle’s exterior plastic parts such
as a bumper, spoiler, garnish, lamp
or outside rearview mirror might be
damaged due to sunlight reflected
from the sign or building. To prevent
damage of the exterior plastic parts,
you should avoid parking in areas
where light may be reflected or use a
car cover. (The exterior plastic parts
applied to your vehicle may vary.)
Exterior care
Exterior general caution
It is very important to follow the label
directions when using any chemical
cleaner or polish. Read all warning and
caution statements that appear on the
label.
Finish maintenance
: D V K L Q J
To help protect your vehicle’s finish
from rust and deterioration, wash it
thoroughly and frequently at least once
a month with lukewarm or cold water.
If you use your vehicle for off-road driving,
you should wash it after each off-road trip.
Pay special attention to the removal of any
accumulation of salt, dirt, mud, and other
foreign materials. Make sure the drain
holes in the lower edges of the doors and
rocker panels are kept clear and clean.
Insects, tar, tree sap, bird droppings,
industrial pollution and similar deposits
can damage your vehicle’s finish if not
removed immediately.
Even prompt washing with plain water
may not completely remove all these
deposits.
A mild soap, safe for use on painted
surfaces, may be used.
After washing, rinse the vehicle
thoroughly with lukewarm or cold water.
Do not allow soap to dry on the finish.
NOTICE
[ ' R Q R W X V H V W U R Q J V R D S F K H P L F D O
detergents or hot water, and do not
wash the vehicle in direct sunlight
or when the body of the vehicle is
warm.
[ % H F D U H I X O Z K H Q Z D V K L Q J W K H V L G H
windows of your vehicle.
Especially, with high-pressure water,
water may leak through the windows
and wet the interior.
[ 7 R S U H Y H Q W G D P D J H W R W K H S O D V W L F
parts and lamps, do not clean
with chemical solvents or strong
detergents.
WARNING
Wet brakes
After washing the vehicle, test the
brakes whilst driving slowly to see if
they have been affected by water. If
braking performance is impaired, dry
the brakes by applying them lightly
whilst maintaining a slow forward
speed.
+ L J K S U H V V X U H Z D V K L Q J
[ : K H Q X V L Q J K L J K S U H V V X U H Z D V K H U V
make sure to maintain sufficient
distance from the vehicle.
Insufficient clearance or excessive
pressure can lead to component
damage or water penetration.
[ ' R Q R W V S U D \ W K H F D P H U D V H Q V R U V R U
its surrounding area directly with a
high pressure washer. Shock applied
from high pressure water may cause
the device to not operate normally.
[ ' R Q R W E U L Q J W K H Q R ] ] O H W L S F O R V H W R
boots (rubber or plastic covers) or
connectors as they may be damaged
if they come into contact with high
pressure water.
APPEARANCE CARE
Page 642 of 649
9-83
09
WARNING
After washing the vehicle, test the
brakes whilst driving slowly to see if
they have been affected by water. If
braking performance is impaired, dry
the brakes by applying them lightly
whilst maintaining a slow forward
speed.
Aluminium wheel maintenance
The aluminium wheels are coated with a
clear protective finish.
NOTICE
[ ' R Q R W X V H D Q \ D E U D V L Y H F O H D Q H U
polishing compound, solvent, or wire
brushes on aluminium wheels.
[ & O H D Q W K H Z K H H O Z K H Q L W K D V F R R O H G
[ 8 V H R Q O \ D P L O G V R D S R U Q H X W U D O
detergent, and rinse thoroughly with
water. Also, be sure to clean the
wheels after driving on salted roads.
[ ' R Q R W Z D V K W K H Z K H H O V Z L W K K L J K
speed car wash brushes.
[ ' R Q R W X V H D Q \ F O H D Q V H U F R Q W D L Q L Q J
acid or alkaline detergents.
Corrosion protection
3 U R W H F W L Q J \ R X U Y H K L F O H I U R P F R U U R
V L R Q
By using the most advanced design
and construction practices to combat
corrosion, we produces vehicles of the
highest quality. However, this is only
part of the job. To achieve the long-term
corrosion resistance your vehicle can
deliver, the owner’s cooperation and
assistance is also required.
& R P P R Q F D X V H V R I F R U U R V L R Q
The most common causes of corrosion
on your vehicle are:
[ Road salt, dirt and moisture that is
allowed to accumulate underneath the
vehicle.
[ Removal of paint or protective
coatings; by stones, gravel, abrasion
or minor scrapes and dents which
leave unprotected metal exposed to
corrosion.
+ L J K F R U U R V L R Q D U H D V
If you live in an area where your vehicle
is regularly exposed to corrosive
materials, corrosion protection is
particularly important. Some of the
common causes of accelerated
corrosion are road salts, dust control
chemicals, ocean air and industrial
pollution.