2023 HYUNDAI I20 brake light
[x] Cancel search: brake lightPage 309 of 649
6-36
Driving your vehicle
Rear drum brakes
Your rear drum brakes do not have wear
indicators. Therefore, have the rear
brake linings inspected if you hear a rear
brake rubbing noise. Also have your rear
brakes inspected each time you change
or rotate your tyres and when you have
the front brakes replaced.
Parking brake
OBC3060005
Always set the parking brake before
leaving the vehicle, to apply:
Firmly depress the brake pedal.
Pull up the parking brake lever as far as
possible.
WARNING
To reduce the risk of SERIOUS INJURY
or DEATH, do not operate the parking
brake whilst the vehicle is moving
except in an emergency situation. It
could damage the brake system and
lead to an accident.
OBC3060006
To release:
Firmly depress the brake pedal.
Slightly pull up the parking brake lever.
Whilst pressing the release button (1),
lower the parking brake (2).
If the parking brake does not release
or does not release all the way, we
recommend that the system be checked
by a HYUNDAI authorised repairer.
WARNING
Whenever leaving the vehicle or
parking, always come to a complete
stop and continue to depress the brake
pedal.
Move the shift is in the 1st gear when
the vehicle is parked on a uphill and in
R (Reverse) on an downhill (for manual
transmission vehicle), or P (Park, for
automatic transmission/dual clutch
transmission vehicle) position, then
apply the parking brake, and place
the ignition switch in the LOCK/OFF
position.
Page 310 of 649
6-37
06
Parking brake warning light
Check the Parking Brake
Warning Light by placing the
ignition switch to the ON
position (do not start the
engine).
This light will illuminate when the
parking brake is applied with the ignition
switch in the START or ON position.
Before driving, be sure the parking brake
is released and the Brake Warning Light
is OFF.
If the Parking Brake Warning Light
remains on after the parking brake is
released whilst the engine is running,
there may be a malfunction in the
brake system. Immediate attention is
necessary.
If at all possible, cease driving the
vehicle immediately. If that is not
possible, use extreme caution whilst
operating the vehicle and only continue
to drive the vehicle until you can reach a
safe location.
Anti-lock Brake System (ABS)
WARNING
An Anti-Lock Braking System (ABS) or
an Electronic Stability Control (ESC)
system will not prevent accidents
due to improper or dangerous driving
manoeuvres. Even though vehicle
control is improved during emergency
braking, always maintain a safe
distance between you and objects
ahead of you. Vehicle speeds should
always be reduced during extreme
road conditions. The braking distance
for vehicles equipped with ABS or ESC
may be longer than for those without
these systems in the following road
conditions.
Drive your vehicle at reduced speeds
during the following conditions:
[ Rough, gravel or snow-covered
roads.
[ On roads where the road surface is
pitted or has different surface height.
[ Tyre chains are installed on your
vehicle.
The safety features of an ABS or ESC
equipped vehicle should not be tested
by high speed driving or cornering. This
could endanger the safety of yourself
or others.
ABS is an electronic braking system that
helps prevent a braking skid. ABS allows
the driver to steer and brake at the same
time.
Page 311 of 649
6-38
Driving your vehicle
Using ABS
To obtain the maximum benefit from
your ABS in an emergency situation,
do not attempt to modulate your brake
pressure and do not try to pump your
brakes. Depress your brake pedal as
hard as possible.
When you apply your brakes under
conditions which may lock the wheels,
you may hear sounds from the brakes,
or feel a corresponding sensation in the
brake pedal. This is normal and it means
your ABS is active.
ABS does not reduce the time or
distance it takes to stop the vehicle.
Always maintain a safe distance from the
vehicle in front of you.
ABS will not prevent a skid that results
from sudden changes in direction, such
as trying to take a corner too fast or
making a sudden lane change. Always
drive at a safe speed for the road and
weather conditions.
ABS cannot prevent a loss of stability.
Always steer moderately when braking
hard. Severe or sharp steering wheel
movement can still cause your vehicle
to veer into oncoming traffic or off the
road.
On loose or uneven road surfaces,
operation of the anti-lock brake system
may result in a longer stopping distance
than for vehicles equipped with a
conventional brake system.
The ABS warning light (
) will stay
on for several seconds after the ignition
switch is in the ON position. During
that time, the ABS will go through self-
diagnosis and the light will go off if
everything is normal. If the light stays
on, you may have a problem with your
ABS. We recommend that you contact a
HYUNDAI authorised repairer as soon as
possible.
WARNING
If the ABS warning light () is on and
stays on, you may have a problem with
the ABS. Your power brakes will work
normally. To reduce the risk of serious
injury or death, we recommend that
you contact your HYUNDAI dealer as
soon as possible.
NOTICE
When you drive on a road having poor
traction, such as an icy road, and apply
your brakes continuously, the ABS will
be active continuously and the ABS
warning light (
) may illuminate. Pull
your vehicle over to a safe place and
turn the engine off.
Restart the engine. If the ABS warning
light is off, then your ABS system is
normal.
Otherwise, you may have a problem
with your ABS system. We recommend
that you contact a HYUNDAI authorised
repairer as soon as possible.
i Information
: K H Q \ R X M X P S V W D U W \ R X U Y H K L F O H
E H F D X V H R I D G U D L Q H G E D W W H U \ W K H $ % 6
Z D U Q L Q J O L J K W
P D \ W X U Q R Q D W W K H
V D P H W L P H 7 K L V K D S S H Q V E H F D X V H R I W K H
O R Z E D W W H U \ Y R O W D J H , W G R H V Q R W P H D Q \ R X U
$ % 6 L V P D O I X Q F W L R Q L Q J + D Y H W K H E D W W H U \
U H F K D U J H G E H I R U H G U L Y L Q J W K H Y H K L F O H
Page 312 of 649
6-39
06
Electronic Stability Control
(ESC)
OBC3N061006AU
The Electronic Stability Control (ESC)
system helps to stabilize the vehicle
during cornering manoeuvres.
ESC checks where you are steering and
where the vehicle is actually going.
ESC applies braking pressure to any one
of the vehicle’s brakes and intervenes in
the engine management system to assist
the driver with keeping the vehicle on
the intended path. It is not a substitute
for safe driving practices. Always adjust
your speed and driving to the road
conditions.
WARNING
Never drive too fast for the road
conditions or too quickly when
cornering. The ESC system will not
prevent accidents.
Excessive speed in turns, abrupt
manoeuvres, and hydroplaning on wet
surfaces can result in severe accidents.
ESC operation
( 6 & 2 1 F R Q G L W L R Q
When the ignition switch is in the
ON position, the ESC and the ESC
OFF indicator lights illuminate for
approximately three seconds. After both
lights go off, the ESC is enabled.
: K H Q R S H U D W L Q J
When the ESC is in
operation, the ESC indicator
light blinks:
[ : K H Q \ R X D S S O \ \ R X U E U D N H V X Q G H U
conditions which may lock the wheels,
you may hear sounds from the brakes,
or feel a corresponding sensation in
the brake pedal. This is normal and it
means your ESC is active.
[ : K H Q W K H ( 6 & D F W L Y D W H V W K H H Q J L Q H
may not respond to the accelerator as
it does under routine conditions.
[ , I W K H & U X L V H & R Q W U R O Z D V L Q X V H Z K H Q
the ESC activates, the Cruise Control
automatically disengages. The Cruise
Control can be reengaged when the
road conditions allow. See “Cruise
Control System” later in this chapter
7 (if equipped).
[ : K H Q P R Y L Q J R X W R I W K H P X G R U
driving on a slippery road, the engine
RPM (revolutions per minute) may
not increase even if you press the
accelerator pedal deeply. This is to
maintain the stability and traction of
the vehicle and does not indicate a
problem.
Page 313 of 649
6-40
Driving your vehicle
( 6 & 2 ) ) F R Q G L W L R Q
To cancel ESC operation :
[ 6 W D W H
Press the ESC OFF button briefly. The
ESC OFF indicator light and/or message
‘Traction Control disabled’ will illuminate
and a warning chime sounds. In this
state, the traction control function of
ESC (engine management) is disabled,
but the brake control function of ESC
(braking management) still operates.
[ 6 W D W H
Press and hold the ESC OFF button
continuously for more than 3 seconds.
The ESC OFF indicator light and/or
message ‘Traction control and ESC
disabled’ illuminates and a warning
chime sounds. In this state, both the
traction control function of ESC (engine
management) and the brake control
function of ESC (braking management)
are disabled.
If the ignition switch is placed in the
LOCK/OFF position when ESC is off, ESC
remains off. Upon restarting the vehicle,
the ESC will automatically turn on again.
Indicator lights
„ ESC indicator light (blinks)
„ ESC OFF indicator light (comes on)
OTD059013
OTD059012
When the ignition switch is in the
ON position, the ESC indicator light
illuminates, then goes off if the ESC
system is operating normally.
The ESC indicator light blinks whenever
the ESC is operating.
If the ESC indicator light stays on, your
vehicle may have a malfunction with
the ESC system. When this warning
light illuminates we recommend that
the vehicle be checked by a HYUNDAI
authorised repairer as soon as possible.
The ESC OFF indicator light comes on
when the ESC is turned off with the
button.
WARNING
When the ESC is blinking, this indicates
the ESC is active:
Drive slowly and NEVER attempt to
accelerate. NEVER turn the ESC off
whilst the ESC indicator light is blinking
or you may lose control of the vehicle
resulting in an accident.
NOTICE
Driving with wheels and tyres with
different sizes may cause the ESC
system to malfunction. Before
replacing tyres, make sure all four tyres
and wheels are the same size. Never
drive the vehicle with different sized
wheels and tyres installed.
Page 314 of 649
6-41
06
ESC OFF usage
: K H Q ' U L Y L Q J
The ESC OFF mode should only be used
briefly to help free the vehicle if stuck in
snow or mud, by temporarily stopping
operation of the ESC, to maintain wheel
torque.
To turn ESC off whilst driving, press the
ESC OFF button whilst driving on a flat
road surface.
NOTICE
To prevent damage to the transmission:
[ ' R Q R W D O O R Z Z K H H O V R I R Q H D [ O H W R
spin excessively whilst the ESC, ABS,
and parking brake warning lights
are displayed. The repairs would not
be covered by the vehicle warranty.
Reduce engine power and do not spin
the wheel(s) excessively whilst these
lights are displayed.
[ : K H Q R S H U D W L Q J W K H Y H K L F O H R Q
a dynamometer, make sure the
ESC is turned off (ESC OFF light
illuminated).
i Information
7 X U Q L Q J W K H ( 6 & R I I G R H V Q R W D I I H F W $ % 6
R U V W D Q G D U G E U D N H V \ V W H P R S H U D W L R Q
Vehicle Stability Management
(VSM)
The Vehicle Stability Management (VSM)
is a function of the Electronic Stability
Control (ESC) system. It helps ensure the
vehicle stays stable when accelerating
or braking suddenly on wet, slippery and
rough roads where traction over the four
tyres can suddenly become uneven.
WARNING
Take the following precautions when
using the Vehicle Stability Management
(VSM):
[ $ / : $ < 6 F K H F N W K H V S H H G D Q G W K H
distance to the vehicle ahead. The
VSM is not a substitute for safe
driving practices.
[ 1 H Y H U G U L Y H W R R I D V W I R U W K H U R D G
conditions. The VSM system will not
prevent accidents. Excessive speed
in bad weather, slippery and uneven
roads can result in severe accidents.
Page 318 of 649
6-45
06
Good braking practices
WARNING
Whenever leaving the vehicle or
parking, always come to a complete
stop and continue to depress the brake
pedal. Move the shift lever into the 1st
gear (for Manual transmission vehicle)
or N (Neutral) position (for Automatic
transmission/Dual clutch transmission
vehicle), then apply the parking brake,
and place the ignition switch in the
LOCK/OFF position.
Vehicles parked with the parking brake
not applied or not fully engaged may
roll inadvertently and may cause injury
to the driver and others. ALWAYS apply
the parking brake before exiting the
vehicle.Wet brakes can be dangerous! The
brakes may get wet if the vehicle is
driven through standing water or if it is
washed.
Your vehicle will not stop as quickly if
the brakes are wet. Wet brakes may
cause the vehicle to pull to one side.
To dry the brakes, apply the brakes
lightly until the braking action returns to
normal. If the braking action does not
return to normal, stop as soon as it is
safe to do so and we recommend that
you call a HYUNDAI authorised repairer
for assistance.
DO NOT drive with your foot resting on
the brake pedal. Even light, but constant
pedal pressure can result in the brakes
overheating, brake wear, and possibly
even brake failure.
If a tyre goes flat whilst you are driving,
apply the brakes gently and keep the
vehicle pointed straight ahead whilst you
slow down. When you are moving slowly
enough for it to be safe to do so, pull off
the road and stop in a safe location.
Keep your foot firmly on the brake pedal
when the vehicle is stopped to prevent
the vehicle from rolling forward.
Page 319 of 649
6-46
Driving your vehicle
Your vehicle may be equipped with
the ISG system, which reduces fuel
consumption by stopping and restarting
the engine automatically.
The engine starts automatically as soon
as the starting conditions are met.
NOTICE
When the engine automatically starts
by the ISG system, some warning lights
(ABS, ESC, ESC OFF, EPS or Parking
brake warning light) may turn on for a
few seconds. This happens because of
low battery voltage. It does not mean
the system is malfunctioning.
Activating the ISG
Prerequisite for activation
The ISG system operates in the following
situations.
[ The driver’s seatbelt is fastened
[ The driver’s door and bonnet are
closed
[ The brake vacuum pressure is
adequate
[ The battery sensor is activated and the
battery is sufficiently charged
[ Outside temperature is not too low or
too high
[ The vehicle is driven over a constant
speed and stops
[ The climate control system satisfies
the conditions
[ The vehicle is sufficiently warmed up
[ The incline is gradual
[ The steering wheel is turned less than
180 degrees and then the vehicle
stops
Deactivating the ISG
OBC3N061014AU
If you want to deactivate the ISG system,
press the ISG OFF button.
The light on the ISG OFF button will
illuminate.
If you press the ISG OFF button again,
the system will be activated and the light
on the ISG OFF button will turn off.
, ' / ( 6 7 2 3 $ 1 ' * 2