2023 HYUNDAI I20 BUMPER

07
7-161
OBC3070118TU
3. Checking space
(1) When the vehicle is parked parallel,
the vehicle sensors will detect the
distance from nearby objects and
check for space to exit.

[If the front or rear vehicle (or object) is
too near, the function will not be able
to search for space, and will turn off.

[Parking Assist may not be able to
search for space even if there is space
to leave, and the function may search
for a space that is not suitable for
the vehicle to leave in the following
circumstances:
- The ultrasonic sensor is frozen or
dirty
- There are objects located high or low
- There are pillars around the parking
space
- The parked vehicle has objects
attached to the bumper such as
bumper guard, trailer hitch, etc. OBC3070100TU/OBC3070102TU
OBC3070101TU/OBC3070099TU
4. Steering wheel control
(1) Shift the gear to D (Drive) or R
(Reverse) according to the message
on the cluster.
(2) Parking Assist will start to control the
steering wheel.
- If the steering wheel is held tight,
Parking Assist will be cancelled.
(3) Take your foot off the brake pedal
and drive forward or in reverse
according to the message on the
cluster.

07
7-165
[There is a circular pillar or narrow
pillar, or a pillar surrounded by objects
such as fire extinguisher, etc. near the
parking space

[The road surface is bumpy (curbstone,
speed bump, etc.)

[The road is slippery

[The parking space is near a vehicle
with higher ground clearance or big,
such as a truck, etc.

[The parking space is Inclined

[There is heavy wind

[Operating the function on uneven
roads, gravel roads, bushes, etc.

[The performance of the ultrasonic
sensor is affected by extremely hot or
cold weather

[The ultrasonic sensor is covered with
snow or water

[An object that generates ultrasonic
waves is nearby

[Wireless transmitters or mobile
phones are present near the sensor

[Your vehicle is affected by another
YHKLFOH
TV3DUNLQJ'LVWDQFH:DUQLQJ

[The sensor is mounted or positioned
incorrectly by an impact to the
bumper

[When the ultrasonic sensor cannot
detect the following objects:
- Sharp or slim objects such as ropes,
chains or small poles
- Objects smaller than 100 cm (40 in.)
in length and narrower than 14 cm (6
in.) in diameter
- Objects which tend to absorb sensor
frequency such as clothes, spongy
material or snowParking Assist may not operate normally
under the following circumstances:

[Parking on inclines
OBC3070082TU
Park manually when parking on
inclines.

[Parking in snow
OBC3070083TU
Snow may interfere with sensor
operation, or Parking Assist may
cancel if the road is slippery whilst
parking.

8-17
08
Changing tyres
WARNING
A vehicle can slip or roll off of a jack
causing serious injury or death to you
or those nearby. Take the following
safety precautions:

[Do not get under a vehicle that is
supported by a jack.

[NEVER attempt to change a tyre in
the lane of traffic. ALWAYS move the
vehicle completely off the road on
level, firm ground away from traffic
before trying to change a tyre. If you
cannot find a level, firm place off
the road, call a towing service for
assistance.

[Be sure to use the jack provided with
the vehicle.

[ALWAYS place the jack on the
designated jacking positions on the
vehicle and NEVER on the bumpers
or any other part of the vehicle for
jacking support.

[Do not start or run the engine whilst
the vehicle is on the jack.

[Do not allow anyone to remain in the
vehicle whilst it is on the jack.

[Keep children away from the road
and the vehicle.
Follow these steps to change your
vehicle’s tyre:
1. Park on a level, firm surface.
2. Move the shift lever into P (Park, for
automatic transmission/dual clutch
transmission vehicle) or neutral
(for manual transmission vehicle),
apply the parking brake, and place
the ignition switch in the LOCK/OFF
position.
3. Press the hazard warning flasher
button.
4. Remove the wheel lug nut wrench,
jack, jack handle, and spare tyre from
the vehicle.
OBC3080005
[A] : Block
5. Block both the front and rear of the
tyre diagonally opposite of the tyre
you are changing.
OBC3080006
6. Loosen the wheel lug nuts
counterclockwise one turn each in
the order shown above, but do not
remove any lug nuts until the tyre has
been raised off of the ground.

8-33
08
When towing your vehicle in an
emergency without wheel dollies:
1. Place the ignition switch in the ACC
position.
2. Place the shift lever in N (Neutral).
3. Release the parking brake.
CAUTION
Failure to place the shift lever in N
(Neutral) may cause internal damage to
the transmission.
Removable towing hook
OBC3080017
1. Open the tailgate, and remove the
towing hook from the tool case.
OBC3080018
2. Remove the hole cover by pressing
the lower part of the cover on the
bumper.
3. Install the towing hook by turning it
clockwise into the hole until it is fully
secured.
4. Remove the towing hook and install
the cover after use.

9-62
Maintenance
+HDGOLJKW/RZ+LJK
1. Turn the front wheel at inwards.
OAC3089042TU
OAC3089043TU
OBC3090055
2. Remove the Wheel guard clips (B),
bumper cover bolt (A) and bumper
upper cover blots (C).
3. Push the wheel guard aside and
remove the headlight bulb cover by
turning it counterclockwise from bulb
assembly.
OBC3090038
OBC3TN091005
„CUV
4. Disconnect the headlight bulb socket-
connector.
5. Unsnap the headlight bulb retaining
wire by depressing the end and
pushing it upward.
6. Remove the bulb from the headlight
assembly.
7. Install a new headlight bulb and snap
the headlight bulb retaining wire into
position by aligning the wire with the
groove on the bulb.
8. Connect the headlight bulb socket
connector.
9. Install the headlight bulb cover by
turning it clockwise.
10. Install the wheel guard in the reverse
order.

9-65
09
„Front Fog light
OBC3090040
)RJOLJKWLIHTXLSSHG
1. Remove the under cover by rotating
the screws and bolts.
2. Reach your hand into the back of the
front bumper.
3. Disconnect the power connector from
the socket.
4. Remove the bulb-socket from
the housing by turning the socket
counterclockwise until the tabs on
the socket align with the slots on the
housing.
5. Install the new bulb-socket into the
housing by aligning the tabs on the
socket with the slots in the housing.
Push the socket into the housing and
turn the socket clockwise.
6. Connect the power connector to the
socket.
7. Reinstall the front bumper under
cover.
Headlight and front fog light
aiming (For Europe, if equipped)
Headlight aiming
„Type A
OBC3090041
„Type B
OBC3090057
„Type C
OBC3TN091004
1. Inflate the tyres to the specified
pressure and remove any loads from
the vehicle except the driver, spare
tyre, and tools.
2. The vehicle should be placed on a flat
floor.

9-80
Maintenance
NOTICE
If you park your vehicle near a stainless
steel sign or glass facade building, the
vehicle’s exterior plastic parts such
as a bumper, spoiler, garnish, lamp
or outside rearview mirror might be
damaged due to sunlight reflected
from the sign or building. To prevent
damage of the exterior plastic parts,
you should avoid parking in areas
where light may be reflected or use a
car cover. (The exterior plastic parts
applied to your vehicle may vary.)
Exterior care
Exterior general caution
It is very important to follow the label
directions when using any chemical
cleaner or polish. Read all warning and
caution statements that appear on the
label.
Finish maintenance
:DVKLQJ
To help protect your vehicle’s finish
from rust and deterioration, wash it
thoroughly and frequently at least once
a month with lukewarm or cold water.
If you use your vehicle for off-road driving,
you should wash it after each off-road trip.
Pay special attention to the removal of any
accumulation of salt, dirt, mud, and other
foreign materials. Make sure the drain
holes in the lower edges of the doors and
rocker panels are kept clear and clean.
Insects, tar, tree sap, bird droppings,
industrial pollution and similar deposits
can damage your vehicle’s finish if not
removed immediately.
Even prompt washing with plain water
may not completely remove all these
deposits.
A mild soap, safe for use on painted
surfaces, may be used.
After washing, rinse the vehicle
thoroughly with lukewarm or cold water.
Do not allow soap to dry on the finish.
NOTICE

[ 'RQRWXVHVWURQJVRDSFKHPLFDO
detergents or hot water, and do not
wash the vehicle in direct sunlight
or when the body of the vehicle is
warm.

[ %HFDUHIXOZKHQZDVKLQJWKHVLGH
windows of your vehicle.
Especially, with high-pressure water,
water may leak through the windows
and wet the interior.

[ 7RSUHYHQWGDPDJHWRWKHSODVWLF
parts and lamps, do not clean
with chemical solvents or strong
detergents.
WARNING
Wet brakes
After washing the vehicle, test the
brakes whilst driving slowly to see if
they have been affected by water. If
braking performance is impaired, dry
the brakes by applying them lightly
whilst maintaining a slow forward
speed.
+LJKSUHVVXUHZDVKLQJ

[ :KHQXVLQJKLJKSUHVVXUHZDVKHUV
make sure to maintain sufficient
distance from the vehicle.
Insufficient clearance or excessive
pressure can lead to component
damage or water penetration.

[ 'RQRWVSUD\WKHFDPHUDVHQVRUVRU
its surrounding area directly with a
high pressure washer. Shock applied
from high pressure water may cause
the device to not operate normally.

[ 'RQRWEULQJWKHQR]]OHWLSFORVHWR
boots (rubber or plastic covers) or
connectors as they may be damaged
if they come into contact with high
pressure water.
APPEARANCE CARE