2023 HYUNDAI I20 clock

8-33
08
When towing your vehicle in an
emergency without wheel dollies:
1. Place the ignition switch in the ACC
position.
2. Place the shift lever in N (Neutral).
3. Release the parking brake.
CAUTION
Failure to place the shift lever in N
(Neutral) may cause internal damage to
the transmission.
Removable towing hook
OBC3080017
1. Open the tailgate, and remove the
towing hook from the tool case.
OBC3080018
2. Remove the hole cover by pressing
the lower part of the cover on the
bumper.
3. Install the towing hook by turning it
clockwise into the hole until it is fully
secured.
4. Remove the towing hook and install
the cover after use.

9-17
09
OBC3090006
„Type A
„Type B
OBC3090007
WARNING
Do not remove a radiator cap/
engine coolant reservoir cap.

[Never attempt to remove the radiator
cap/engine coolant reservoir cap
whilst the engine is operating or hot.

[Doing so might lead to cooling
system failure and engine damage
and could result in serious personal
injury from escaping hot coolant or
steam.

[Turn the engine off and wait until
it cools down. Use extreme care
when removing the radiator cap/
engine coolant reservoir cap. Wrap
a thick towel around it, and turn it
counterclockwise slowly to the first
stop. Step back whilst the pressure is
released from the cooling system.
[When you are sure all the pressure
has been released, press down on the
cap, using a thick towel, and continue
turning counterclockwise to remove
it.

[Even if the engine is not operating,
do not remove the radiator cap/
engine coolant reservoir cap or the
drain plug whilst the engine and
radiator are hot. Hot coolant and
steam may still blow out under
pressure, causing serious injury.
WARNING
The electric motor (cooling
fan) is controlled by engine
coolant temperature,
refrigerant pressure and
vehicle speed.
It may sometimes operate even when
the engine is not running. Use extreme
caution when working near the blades
of the cooling fan so that you are not
injured by a rotating fan blades. As the
engine coolant temperature decreases,
the electric motor will automatically
shut off. This is a normal condition.
The electric motor (cooling fan) may
operate until you disconnect the
negative battery cable.

9-62
Maintenance
+HDGOLJKW/RZ+LJK
1. Turn the front wheel at inwards.
OAC3089042TU
OAC3089043TU
OBC3090055
2. Remove the Wheel guard clips (B),
bumper cover bolt (A) and bumper
upper cover blots (C).
3. Push the wheel guard aside and
remove the headlight bulb cover by
turning it counterclockwise from bulb
assembly.
OBC3090038
OBC3TN091005
„CUV
4. Disconnect the headlight bulb socket-
connector.
5. Unsnap the headlight bulb retaining
wire by depressing the end and
pushing it upward.
6. Remove the bulb from the headlight
assembly.
7. Install a new headlight bulb and snap
the headlight bulb retaining wire into
position by aligning the wire with the
groove on the bulb.
8. Connect the headlight bulb socket
connector.
9. Install the headlight bulb cover by
turning it clockwise.
10. Install the wheel guard in the reverse
order.

9-63
09
OBC3090039
OBC3TN091006
„CUV
7XUQVLJQDOOLJKW
1. Open the bonnet.
2. Remove the turn signal light or low
beam assist-static light bulb cover by
turning it counterclockwise.
3. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on the
assembly.
4. Insert a new bulb by inserting it into
the socket and rotating it until it locks
into place.
5. Install the socket in the assembly by
aligning the tabs on the socket with
the slots in the assembly.
Push the socket into the assembly and
turn the socket clockwise.
6. Install the turn signal light or low
beam assist-static light bulb cover by
turning it clockwise.
3RVLWLRQOLJKW'D\WLPHUXQQLQJOLJKW
LIHTXLSSHG
If the LED lamp does not operate,
we recommend that the system be
inspected by a HYUNDAI authorised
repairer.
The LED lamps cannot be replaced as
a single unit because it is an integrated
unit. The LED lamp has to be replaced
with the unit. Unless a skilled technician
checks or repairs the LED lamp, it may
damage related parts of the vehicle.

9-65
09
„Front Fog light
OBC3090040
)RJOLJKWLIHTXLSSHG
1. Remove the under cover by rotating
the screws and bolts.
2. Reach your hand into the back of the
front bumper.
3. Disconnect the power connector from
the socket.
4. Remove the bulb-socket from
the housing by turning the socket
counterclockwise until the tabs on
the socket align with the slots on the
housing.
5. Install the new bulb-socket into the
housing by aligning the tabs on the
socket with the slots in the housing.
Push the socket into the housing and
turn the socket clockwise.
6. Connect the power connector to the
socket.
7. Reinstall the front bumper under
cover.
Headlight and front fog light
aiming (For Europe, if equipped)
Headlight aiming
„Type A
OBC3090041
„Type B
OBC3090057
„Type C
OBC3TN091004
1. Inflate the tyres to the specified
pressure and remove any loads from
the vehicle except the driver, spare
tyre, and tools.
2. The vehicle should be placed on a flat
floor.

9-66
Maintenance
3. Draw vertical lines (Vertical lines
passing through respective head
light centres) and a horizontal line
(Horizontal line passing through
centre of head lamps) on the screen.
4. With the headlight and battery in
normal condition, aim the headlights
so the brightest portion falls on the
horizontal and vertical lines.
5. To aim the low beam left or
right, turn the driver clockwise or
counterclockwise. To aim the low
beam up or down, turn the driver
clockwise or counterclockwise.
To aim the high beam up or
down, turn the driver clockwise or
counterclockwise.Front fog light aiming (if equipped)
OBC3090042
The front fog light can be aimed as the
same manner of the head lights aiming.
With the front fog lights and battery
normal condition, aim the front fog
lights. To aim the front fog light up
or down, turn the driver clockwise or
counterclockwise.

9-70
Maintenance
Side repeater light replacement
Type A
OBC3090044
If the LED lamp does not operate, we
recommend you to have the vehicle
checked by a HYUNDAI authorised
repairer.
Type B
OAC3089047TU
1. Remove the lamp assembly from the
vehicle by prying the lens and pulling
the assembly out.
2. Disconnect the bulb electrical
connector.
3. Separate the socket and the
lens parts by turning the socket
counterclockwise until the tabs on the
socket align with the slots on the lens
part.
4. Remove the bulb by pulling it straight
out.
5. Insert a new bulb in the socket.
6. Reassemble the socket and the lens
part.
7. Connect the bulb electrical connector.
8. Reinstall the lamp assembly to the
body of the vehicle.

9-72
Maintenance
OBC3090047
[1] : Turn Signal Light, [2] : Tail/Stop Light,
[3] : Tail light
7XUQVLJQDOOLJKW7DLOVWRSOLJKW
4. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on the
assembly.
5. Remove the bulb from the socket
by pressing it in and rotating it
counterclockwise until the tabs on the
bulb align with the slots in the socket.
Pull the bulb out of the socket.
6. Insert a new bulb by inserting it into
the socket and rotating it until it locks
into place.
7. Install the socket in the assembly by
aligning the tabs on the socket with
the slots in the assembly. Push the
socket into the assembly and turn the
socket clockwise.
8. Reinstall the light assembly to the
body of the vehicle.
7DLOOLJKW
1. Open the tailgate and remove the
tailgate trim.
2. Loosen the retaining screw of the
tailgate lid cover and then remove the
cover.
3. Disconnect the connector and then
remove the nuts by turning the nuts
counter clockwise.
4. Take the light assembly out.
OBC3090049R
[1] : Rear Fog Light, [2] : Back-up Light
5HDUIRJOLJKW%DFNXS/LJKW
1. Remove the rear tire and wheel cover.
2. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on the
assembly.
3. Remove the bulb from the socket
by pressing it in and rotating it
counterclockwise until the tabs on the
bulb align with the slots in the socket.
Pull the bulb out of the socket.
4. Insert a new bulb in the socket.
5. Reinstall the light assembly to the
body of the vehicle.