2023 FORD BRONCO warning

WARNING: Do not drive yourvehicle unless the installed roof panelsare properly secured. Failure to followthis instruction could cause unintendedseparation of the roof panels from yourvehicle.
WARNING: Do not remove ormodify the B-Pillar brace or trim. Doingso could affect safety systemperformance, including safety canopyand front seat mounted side airbags,during a crash or rollover.
Do not remove or modify the C-pillar brace.
Removal of the center and rear roof panelsrequires two adults.
Do not cut, drill, weld or modify the roofpanels or attach anything other than thefactory-installed roof rack.
If there is any damage to the roof panels,see an authorized dealer.
Make sure the locating pins on the rear roofpanel sit flush in your vehicle wheninstalled.
Note:Do not step or kneel on the centerconsole during roof removal or once roofpanels are removed.
Failure to follow these instructions couldcause interior water damage, stains ormildew:
•Properly position the hard topassembly to seal the top to your vehicleduring installation. Improperinstallation could cause water to leakinto the vehicle’s interior.
•Properly handle and store theremovable roof panels. Improperhandling and storage could damagethe seals, causing water to leak intothe vehicle’s interior.
•Do not place anything on top of therear roof panel when it is removed fromthe vehicle. This could cause damageto the rear roof panel and its seals.
REMOVING AND INSTALLING THEFRONT ROOF PANEL -EXCLUDING: RAPTOR
Remove the driver side front roof panelbefore removing the passenger side frontroof panel.
1.Fold down the sun visor against thewindshield.
2.Turn the three L-shaped latches on thedriver side front roof panel, unlockingthem from the roof.
3.Unlatch the driver side header panellatch at the top of the windshield.
385
2023 Bronco (TG1) Canada/United States of America, enUSA, Edition date: 202208, DOMRemovable Vehicle ComponentsE333995

4.Remove the driver side front roof panel.
5.Repeat the steps to remove thepassenger side panel front roof panel.
6.Store the front roof panels in thestorage bag. See Storing the RoofPanels (page 419). See Storing theDoors and the Roof Panels (page407).
7.To install, reverse the removalprocedure.
REMOVING AND INSTALLING THEFRONT ROOF PANEL - RAPTOR
WARNING: Do not remove ormodify the B-Pillar brace or trim. Doingso could affect safety systemperformance, including safety canopyand front seat mounted side airbags,during a crash or rollover.
Do not remove or modify the C-pillar brace.
Remove the driver side front roof panelbefore removing the passenger side frontroof panel.
1.Fold down the sun visor against thewindshield.
2.Turn the three L-shaped latches on thedriver side front roof panel, unlockingthem from the roof.
3.Unlatch the driver side header panellatch at the top of the windshield.
4.Remove the driver side front roof panel.
5.Repeat the steps to remove thepassenger side panel front roof panel.
6.Store the front roof panels in thestorage bag. See Storing the RoofPanels (page 419). See Storing theDoors and the Roof Panels (page407).
7.To install, reverse the removalprocedure.
REMOVING AND INSTALLING THECENTER ROOF PANEL - 4-DOOR,EXCLUDING: RAPTOR
Remove both of the front roof panelsbefore removing the center roof panel.
1.Turn the three L-shaped latches on thecenter roof panel, unlocking them fromthe rear roof panel.
2.Unlatch the driver side and passengerside latches of the center roof panel.
3.Remove the center roof panel.
4.To install, reverse the removalprocedure.
386
2023 Bronco (TG1) Canada/United States of America, enUSA, Edition date: 202208, DOMRemovable Vehicle ComponentsE333995 E333996

REMOVING AND INSTALLING THECENTER ROOF PANEL - RAPTOR,4-DOOR
WARNING: Do not remove ormodify the B-Pillar brace or trim. Doingso could affect safety systemperformance, including safety canopyand front seat mounted side airbags,during a crash or rollover.
Do not remove or modify the C-pillar brace.
Remove both of the front roof panelsbefore removing the center roof panel.
1.Turn the three L-shaped latches on thecenter roof panel, unlocking them fromthe rear roof panel.
2.Unlatch the driver side and passengerside latches of the center roof panel.
3.Remove the center roof panel.
4.To install, reverse the removalprocedure.
REMOVING AND INSTALLING THEREAR ROOF PANEL - 4-DOOR,EXCLUDING: RAPTOR
Remove the front panels and center panelbefore removing the rear roof panel.
1.Open the rear doors.
2.Open the tailgate window. SeeOpening and Closing the Windows(page 113).
3.Locate the wire harness and washerhose on the driver side rear insidecorner of the vehicle.
4.Release the locking tab by pushing itdown.
5.Push the tab inward when pulling downto disconnect and remove the wiringharness.
6.Push the release button on the hoseconnector and pull down to removethe washer hose.
387
2023 Bronco (TG1) Canada/United States of America, enUSA, Edition date: 202208, DOMRemovable Vehicle ComponentsE333996 E335339

REMOVING AND INSTALLING THEREAR ROOF PANEL - RAPTOR, 4-DOOR
WARNING: Do not remove ormodify the B-Pillar brace or trim. Doingso could affect safety systemperformance, including safety canopyand front seat mounted side airbags,during a crash or rollover.
Do not remove or modify the C-pillar brace.
Remove the front panels and center panelbefore removing the rear roof panel.
1.Open the rear doors.
2.Open the tailgate window. SeeOpening and Closing the Windows(page 113).
3.Locate the wire harness and washerhose on the driver side rear insidecorner of the vehicle.
4.Release the locking tab by pushing itdown.
5.Push the tab inward when pulling downto disconnect and remove the wiringharness.
6.Push the release button on the hoseconnector and pull down to removethe washer hose.
7.Secure the wiring harness to the bodyside by plugging it into the receptacleand pushing up on the locking tab.
8.Secure the washer hose by snapping itinto the top of the body sidereceptacle.
389
2023 Bronco (TG1) Canada/United States of America, enUSA, Edition date: 202208, DOMRemovable Vehicle ComponentsE335339 E335340 E345383

Removing and Installing theModular Roof Panel (If Equipped)
Store the modular roof panel in a safeplace when you remove it to prevent partdamage.
Modular roof panelA.
1.Pull and hold the spring-loaded slide.
2.Turn the L-shaped latch.
3.Repeat steps 1 and 2 on the other latchto unlock the modular roof panel fromthe roof.
4.Push up on the front of the panel.
5.Slide the panel forward to remove itfrom your vehicle.
6.To install, reverse the removalprocedure.
Note:Make sure the modular roof panelslides back into place and the locating pinssit in the front latch receiver when installingthe modular roof panel.
Note:You do not need to pull and hold thespring-loaded slides to turn the latches tolock the modular roof panel.
Note:When driving with only the modularroof panel removed, make sure to roll downthe windows.
REMOVABLE HARD TOP (IF
EQUIPPED)
REMOVING AND INSTALLING THEHARD TOP - EXCLUDING: RAPTOR
Bronco Hard Top Removal, Storage andReinstallation
WARNING: When opening, closing,removing or installing the removablevehicle components, take care not to getyour fingers or hands caught in themechanism. Failure to follow thisinstruction could result in personal injury.
1.Remove the roof panels. SeeRemovable Roof Panels (page 384).
2.To install, reverse the removalprocedure.
Removing the Soft Top Trim Piece
(If Equipped)
Make sure to remove the soft top trimpieces before installing the hard top.
Remove the three fasteners to the soft toptrim piece on each side of your vehicleusing the provided head driver and ratchet.
392
2023 Bronco (TG1) Canada/United States of America, enUSA, Edition date: 202208, DOMRemovable Vehicle ComponentsE342198 E334239

REMOVING AND INSTALLING THEHARD TOP - RAPTOR
Bronco Hard Top Removal, Storage andReinstallation
WARNING: When opening, closing,removing or installing the removablevehicle components, take care not to getyour fingers or hands caught in themechanism. Failure to follow thisinstruction could result in personal injury.
WARNING: Do not remove ormodify the B-Pillar brace or trim. Doingso could affect safety systemperformance, including safety canopyand front seat mounted side airbags,during a crash or rollover.
Do not remove or modify the C-pillar brace.
1.Remove the roof panels. SeeRemovable Roof Panels (page 384).
2.To install, reverse the removalprocedure.
Removing the Soft Top Trim Piece
(If Equipped)
Make sure to remove the soft top trimpieces before installing the hard top.
Remove the three fasteners to the soft toptrim piece on each side of your vehicleusing the provided head driver and ratchet.
REMOVABLE SOFT TOP (IF
EQUIPPED)
OPENING AND CLOSING THESOFT TOP
WARNING: When opening, closing,removing or installing the removablevehicle components, take care not to getyour fingers or hands caught in themechanism. Failure to follow thisinstruction could result in personal injury.
Partially Opening the Soft Top
Before pulling into a garage, make surethere is enough clearance.
1.Unlatch the two latches at the header.
2.Push the soft top up and rearward.
393
2023 Bronco (TG1) Canada/United States of America, enUSA, Edition date: 202208, DOMRemovable Vehicle ComponentsE334239 E337137 E337153

WARNING: When opening, closing,removing or installing the removablevehicle components, take care not to getyour fingers or hands caught in themechanism. Failure to follow thisinstruction could result in personal injury.
1.Fully open the soft top. See Openingand Closing the Soft Top (page 393).
2.Remove the three fasteners on eachside in the rear cargo area using theprovided head driver and ratchet.
3.Remove the soft top.
Note:Safely store the soft top when it isoff your vehicle.
4.To install, reverse the removalprocedure. Torque the fasteners thatsecure soft top to the vehicle to15 ± 2 lb.ft (20 ± 3 Nm).
Note:Make sure the soft top is set flush onthe locating pins.
Note:Do not overtighten the fasteners. Youcan strip the fasteners if they areovertightened.
Installing the Soft Top Trim Piece
(If Equipped)
Make sure to install the soft top trim piecesbefore installing the soft top.
Secure the three fasteners to the soft toptrim piece on each side of your vehicleusing the provided head driver and ratchet.
REMOVABLE FENDERS
REMOVABLE FENDERPRECAUTIONS
WARNING: Do not drive yourvehicle on public roads with fendersremoved as you will lose the protectionthey provide in a crash. Failure to followthis instruction could result in personalinjury or death.
397
2023 Bronco (TG1) Canada/United States of America, enUSA, Edition date: 202208, DOMRemovable Vehicle ComponentsE342245 E334239

2.Lock the five quarter turn clips byturning the clips clockwise.
REMOVING THE FENDER FLARES- RAPTOR
The front fender, rear quarter, and fenderflares are not designed to be removed.They are to remain on the vehicle at alltimes.
REMOVABLE RUNNING
BOARDS - RAPTOR
REMOVING AND INSTALLING THERUNNING BOARDS
WARNING: Do not store therunning boards in the vehicle. Unsecuredrunning boards could become aprojectile in a sudden stop or crash.
Note:Running boards are not rated for rockcrawl use or off road conditions whereground contact is likely to occur. Werecommend removing the running boardsbefore use in these conditions in order toavoid damage.
Removing the Running Boards
1.Park your vehicle on level ground andmake sure the transmission is in park(P).
2.Locate the hex tool in the tool pouchand use it to remove two bolts eachfrom front, middle, and rearattachment tabs where the runningboard is mounted to the rock rail.
3.Grab the running board near the frontand rear.
4.Lift up and push forward to disengagethe temporary support pins on therunning board front and middlemounting tabs from keyhole slots inthe rock rail.
5.Pull the running board away from theside of the vehicle.
6.Store running board bolts in the pocketof the tool pouch.
7.To remove the additional runningboard, repeat Steps 1-6 for theopposite side.
8.Return the hex tool to the tool pouchand secure it in the vehicle.
Installing the Running Boards
1.Park your vehicle on level ground andmake sure the transmission is in park(P).
399
2023 Bronco (TG1) Canada/United States of America, enUSA, Edition date: 202208, DOMRemovable Vehicle ComponentsE342192 E366679