2022 TOYOTA RAV4 PLUG-IN HYBRID belt

601-2. Child safety
QInstalling child restraint sys-
tem using a seat belt
Install the child restraint system in
accordance to the operation man-
ual enclosed with the child restraint
system.
If the child restraint system on hand
is not within the “universal” cate-
gory (or the necessary information
is not in the table), refer to the
“Vehicle List” provided by the child
restraint system maker for various
possible installation positions, or
check the compatibility after asking
the retailer of the child seat.
( P.55, 56)
Installation methodPage
Seat belt attachmentP.60
ISOFIX lower anchorage
attachmentP.62
Top tether anchorage
attachmentP.63
Child restraint system fixed
with a seat belt

61
1
1-2. Child safety
For safety and security
1 If installing the child restraint
system to the front passenger
seat is unavoidable, refer to
P.52 for the front passenger
seat adjustment.
2 Adjust the seatback angle to the
most upright position. When
installing a forward-facing child
seat, if there is a gap between
the child seat and the seatback,
adjust the seatback angle until
good contact is achieved.
3 If the head restraint interferes
with the child restraint system
installation and the head
restraint can be removed,
remove the head restraint. Oth-
erwise, put the head restraint in
the upper most position.
( P.232)
4 Run the seat belt through the
child restraint system and insert
the plate into the buckle. Make
sure that the belt is not twisted.
Securely fix the seat belt to the
child restraint system in accor-
dance to the directions enclosed
with the child restraint system.
5 If your child restraint system is
not equipped with a lock-off (a
seat belt locking feature),
secure the child restraint system
using a locking clip.
6 After installing the child restraint
system, rock it back and forth to
ensure that it is installed
securely. ( P.62)
QRemoving a child restraint
system installed with a seat
belt
Press the buckle release button
and fully retract the seat belt.
When releasing the buckle, the child
restraint system may spring up due to
the rebound of the seat cushion.
Release the buckle while holding down
the child restraint system.
Since the seat belt automatically reels
itself, slowly return it to the stowing
position.
QWhen installing a child restraint
system
You may need a locking clip to install the child restraint system. Follow the
instructions provided by the manufac- turer of the system. If your child restraint system does not provide a locking clip,
you can purchase the following item from any authorized Toyota retailer or

621-2. Child safety
Toyota authorized repairer, or any reli-
able repairer: Locking clip for child restraint system(Part No. 73119-22010)
QISOFIX lower anchorages
(ISOFIX child restraint system)
Lower anchorages are provided for
the outboard rear seats. (Tags dis-
playing the location of the anchor-
ages are attached to the seats.)
QInstallation with ISOFIX lower
anchorage (ISOFIX child
restraint system)
Install the child restraint system in
accordance to the operation man-
ual enclosed with the child restraint
system.
If the child restraint system on hand
is not within the “universal” cate-
gory (or the necessary information
is not in the table), refer to the
“Vehicle List” provided by the child
restraint system maker for various
possible installation positions, or
check the compatibility after asking
the retailer of the child seat.
( P.55, 56)
1 Adjust the seatback angle to the
most upright position. When
installing a forward-facing child
WARNING
QWhen installing a child restraint system
Observe the following precautions.
Failure to do so may result in death or serious injury.
ODo not allow children to play with the seat belt. If the seat belt becomes twisted around a child’s
neck, it may lead to choking or other serious injuries that could result in death. If this occurs and
the buckle cannot be unfastened, scissors should be used to cut the belt.
OEnsure that the belt and plate are securely locked and the seat belt is
not twisted.
OShake the child restraint system left
and right, and forward and back- ward to ensure that it has been securely installed.
OAfter securing a child restraint sys-tem, never adjust the seat.
OWhen a junior seat is installed, always ensure that the shoulder
belt is positioned across the center of the child’s shoulder. The belt should be kept away from the
child’s neck, but not so that it could fall off the child’s shoulder.
OFollow all installation instructions provided by the child restraint sys-tem manufacturer.
Child restraint system fixed
with an ISOFIX lower
anchorage

63
1
1-2. Child safety
For safety and security
seat, if there is a gap between
the child seat and the seatback,
adjust the seatback angle until
good contact is achieved.
2 If the head restraint interferes
with the child restraint system
installation and the head
restraint can be removed,
remove the head restraint. Oth-
erwise, put the head restraint in
the upper most position.
( P.232)
3 Check the positions of the exclu-
sive fixing bars, and install the
child restraint system to the
seat.
The bars are installed in the clearance between the seat cushion and seat-
back.
4 After installing the child restraint
system, rock it back and forth to
ensure that it is installed
securely. ( P.62)
QTop tether anchorages
Top tether anchorages are pro-
vided for the outboard rear seats.
Use top tether anchorages when
fixing the top strap.
Top tether anchorages
Top strap
QFixing the top strap to the top
tether anchorages
Install the child restraint system in
WARNING
QWhen installing a child restraint system
Observe the following precautions. Failure to do so may result in death or serious injury.
OAfter securing a child restraint sys-tem, never adjust the seat.
OWhen using the lower anchorages, be sure that there are no foreign
objects around the anchorages and that the seat belt is not caught behind the child restraint system.
OFollow all installation instructions provided by the child restraint sys-
tem manufacturer.
Using a top tether anchor-
age
A
B

641-2. Child safety
accordance to the operation man-
ual enclosed with the child restraint
system.
1 Adjust the head restraint to the
upmost position.
If the head restraint interferes with the
child restraint system or top strap installation and the head restraint can be removed, remove the head restraint.
( P.232)
2Latch the hook onto the top
tether anchorage and tighten
the top strap.
Make sure the top strap is securely latched. ( P.62)
When installing the child restraint sys- tem with the head restraint being raised, be sure to have the top strap
pass underneath the head restraint.
Hook
Top strap
A
B
WARNING
QWhen installing a child restraint system
Observe the following precautions. Failure to do so may result in death or serious injury.
OFirmly attach the top strap and make sure that the belt is not
twisted.
ODo not attach the top strap to any-
thing other than the top tether anchorages.
OAfter securing a child restraint sys-tem, never adjust the seat.
OFollow all installation instructions provided by the child restraint sys-tem manufacturer.
OWhen installing the child restraint system with the head restraint
being raised, after the head restraint has been raised and then the top tether anchorage has been
fixed, do not lower the head restraint.

67
1
1-3. Emergency assistance
For safety and security
at the following URL.
http://www.opensourceautomotive.com/dcm/toyota/
WARNING
QWhen the Emergency Call may
not be made
OIt may not be possible to make Emergency Calls in any of the fol-
lowing situations. In such cases, report to emergency services pro-vider (112 system etc.) by other
means such as nearby public phones.
• Even when the vehicle is in the cel-
lular phone service area, it may be difficult to connect to the eCall con-trol center if the reception is poor or
the line is busy. In such cases, even though the system attempts to connect to the eCall control center,
you may not be able to connect to the eCall control center to make Emergency Calls and contact emer-
gency services.
• When the vehicle is out of the cellu-
lar phone service area, the Emer- gency Calls cannot be made.
• When any related equipment (such as the “SOS” button panel, indicator lights, microphone, speaker, DCM,
antenna, or any wires connecting the equipment) is malfunctioning, damaged or broken, the Emer-
gency Call cannot be made.
• During an Emergency Call, the sys-
tem makes repeated attempts to connect to the eCall control center. However, if it cannot connect to the
eCall control center due to poor radio wave reception, the system may not be able to connect to the
cellular network and the call may finish without connecting. The red indicator light will blink for approxi-
mately 30 seconds to indicate this disconnection.
OIf the 12-volt battery’s voltage decreases or there is a disconnec-tion, the system may not be able to
connect to the eCall control center.
QWhen the Emergency Call sys-
tem is replaced with a new one
The Emergency Call system should be registered. Contact any authorized
Toyota retailer or Toyota authorized repairer, or any reliable repairer.
QFor your safety
OPlease drive safely.The function of this system is to
assist you in making the Emer- gency Call in case of accidents such as traffic accidents or sudden
medical emergencies, and it does not protect the driver or passengers in any way. Please drive safely and
fasten your seatbelts at all times for your safety.
OIn case of an emergency, make lives the top priority.
OIf you smell anything burning or other unusual smells, leave the vehicle and evacuate to a safe area
immediately.
OIf the airbags deploy when the sys-
tem is operating normally, the sys- tem makes emergency call. The system also makes emergency call
when the vehicle is struck from the rear or rolls over, even if the air-bags do not deploy.
OFor safety, do not make the Emer-gency Call while driving.
Making calls during driving may cause mishandling of the steering wheel, which may lead to unex-
pected accidents. Stop the vehicle and confirm the safety of your surroundings before
making the Emergency Call.

1683-1. Instrument cluster
Warning lights inform the driver of
malfunctions in the indicated vehi-
cle’s systems.
*1: These lights turn on when the power
switch is turned to ON to indicate
that a system check is being per-
formed. They will turn off after the
hybrid system is on, or after a few
seconds. There may be a malfunc-
tion in a system if the light does not
come on, or turn off. Have the vehi-
cle inspected by any authorized
Toyota retailer or Toyota authorized
repairer, or any reliable repairer.
*2: This light illuminates on the multi-
Warning lights
(Red)
Brake system warning
light
*1 (P.508)
(Yellow)
Brake system warning
light
*1 (P.508)
Charging system warn-
ing light
*1 (P.509)
High coolant temperature
warning light
*2 (P.509)
Hybrid system overheat
warning light
*2 (P.509)
Low engine oil pressure
warning light
*2 (P.509)
Malfunction indicator
lamp
*1 (P.510)
SRS warning light
*1
(P.510)
ABS warning light
*1
(P.510)
(Red/yellow)
Electric power steering
system warning light
*1
(P.510)
(Flashes or illu-
minates)
PCS warning light*1 (if
equipped) (P.511)
(Orange)
LTA indicator (if
equipped) (P.511)
Toyota parking assist-
sensor OFF indicator
*3
(P.512)
PKSB OFF indicator*1 (if
equipped) (P.512)
BSM OFF indicator
*1 (if
equipped) (P.513)
RCTA OFF indicator
*1 (if
equipped)
(P.513)
Slip indicator light
*1
(P.513)
Inappropriate pedal oper-
ation warning light
*2
(P.514)
(Flashes)
Brake hold operated indi-
cator
*1 (P.514)
(Flashes)
Parking brake indicator
(P.514)
Tire pressure warning
light
*1 (P.515)
Low fuel level warning
light (P.515)
Driver’s and front pas-
senger’s seat belt
reminder light (P.515)
Rear passengers’ seat
belt reminder lights
(P.516)

227
4
4-3. Adjusting the seats
Before driving
Pull the seatback angle adjustment
lever , and adjust the seatback
angle.
WARNING
OMake sure to leave enough space around the feet so they do not get
stuck.
OManual seat only: After adjusting
the seat, make sure that the seat is locked in position.
QSeat adjustment
To reduce the risk of sliding under the lap belt during a collision, do not
recline the seat more than necessary. If the seat is too reclined, the lap belt may slide past the hips and apply
restraint forces directly to the abdo- men, or your neck may contact the shoulder belt, increasing the risk of
death or serious injury in the event of an accident.Adjustments should not be made
while driving as the seat may unex- pectedly move and cause the driver to lose control of the vehicle.
Rear seats
Reclining adjustments and
folding the seatbacks can be
done with lever operation.
Adjustment procedure
WARNING
QWhen operating the seatback
Observe the following precautions. Failure to do so may cause death or serious injury.
OKeep other passengers from being hit with the seatback.
ODo not bring your hands close to the moving parts or between the seats, as well as do not let any part
of your body get caught.
A