2022 TOYOTA RAV4 PLUG-IN HYBRID key battery

205
4
4-2. Opening, closing and locking the doors
Before driving
QSetting the alarm (if equipped)
Locking the doors will set the alarm sys- tem. ( P.78)
QConditions affecting the operation of the smart entry & start system or
wireless remote control
 P.222
QIf the smart entry & start system or the wireless remote control does
not operate properly
OUse the mechanical key to lock and
unlock the doors. ( P.545)
OReplace the key battery with a new
one if it is depleted. ( P.486)
QIf the 12-volt battery is discharged
The doors cannot be locked and unlocked using the smart entry & start
system or wireless remote control. Lock or unlock the doors using the mechani-cal key. ( P.545)
QRear seat reminder function
OIn order to remind you not to forget luggage, etc. in the rear seat, when
the power switch is turned to OFF after any of the following conditions are met, a buzzer will sound and a
message will be displayed on the multi-information display for approxi-mately 6 seconds.
• The hybrid system is started within 10 minutes after opening and closing a rear door.
• A rear door has been opened and closed after the hybrid system was started.
However, if a rear door is opened and
then closed within approximately 2 sec-
onds, the rear seat reminder function
may not operate.
OThe rear seat reminder function deter- mines that luggage, etc. has been
placed in a rear seat based on open- ing and closing of a rear door. There-fore, depending on the situation, the
rear seat reminder function may not operate and you may still forget lug-gage, etc. in the rear seat, or it may
operate unnecessarily.
OThe rear seat reminder function can be enabled/disabled. ( P.569)
QCustomization
Settings (e.g. unlocking function using a key) can be changed.(Customizable features: P.573)
WARNING
QTo prevent an accident
Observe the following precautions while driving the vehicle.
Failure to do so may result in a door opening and an occupant could be thrown out of the vehicle, resulting in
death or serious injury.
OEnsure that all doors are properly closed.
ODo not pull the inside handle of the doors while driving.
Be especially careful for the front doors, as the doors may be opened even if the inside lock buttons are in
locked position.
OSet the rear door child-protector
locks when children are seated in the rear seats.
QWhen opening or closing a door
Check the surroundings of the vehicle such as whether the vehicle is on an
incline, whether there is enough space for a door to open and whether a strong wind is blowing. When open-
ing or closing the door, hold the door handle tightly to prepare for any unpredictable movement.

2224-2. Opening, closing and locking the doors
OWhen an exterior alarm sounds once
for 5 seconds
OWhen an interior alarm pings continu- ously
QBattery-saving function
The battery-saving function will be acti-
vated in order to prevent the electronic key battery and the 12-volt battery from being discharged while the vehicle is not
in operation for a long time.
OIn the following situations, the smart
entry & start system may take some time to unlock the doors.• The electronic key has been left in an
area of approximately 3.5 m (11.5 ft.) of the outside of the vehicle for 2 min-utes or longer.
• The smart entry & start system has not been used for 5 days or longer.
OIf the smart entry & start system has not been used for 14 days or longer, the doors cannot be unlocked at any
doors except the driver’s door. In this case, take hold of the driver’s door handle, or use the wireless remote
control or the mechanical key, to unlock the doors.
QTurning an electronic key to bat-
tery-saving mode
OWhen battery-saving mode is set, bat-
tery depletion is minimized by stop- ping the electronic key from receiving radio waves.
Press twice while pressing and
holding .
Confirm that the electronic key indicator
flashes 4 times.
While the battery-saving mode is set,
the smart entry & start system cannot be
used. To cancel the function, press any
of the electronic key buttons.
OElectronic keys that will not be used for long periods of time can be set to
the battery-saving mode in advance.
QWhen electronic key function stops
If the position of the electronic key has
not changed for a certain amount of time such as when the electronic key is left somewhere, the function of the elec-
tronic key stops to reduce depletion of the battery.In this case, function can automatically
be restored by moving the position of the key such as by lifting it up.
QConditions affecting operation
The smart entry & start system uses
weak radio waves. In the following situa- tions, the communication between the electronic key and the vehicle may be
affected, preventing the smart entry & start system, wireless remote control and immobilizer system from operating
properly.
OWhen the electronic key battery is
depleted
SituationCorrection proce-
dure
An attempt was
made to lock the
vehicle while a
door was open.
Close all of the
doors and lock the
doors again.
SituationCorrection proce-
dure
The power switch
was turned to ACC
while the driver’s
door was open (or
the driver’s door
was opened while
the power switch
was in ACC).
Turn the power
switch to OFF and
close the driver’s
door.

223
4 4-2. Opening, closing and locking the doors
Before driving
ONear a TV tower, electric power plant,
gas station, radio station, large dis-
play, airport or other facility that gen-
erates strong radio waves or electrical
noise
OWhen the electronic key is in contact
with, or is covered by the following
metallic objects
• Cards to which aluminum foil is
attached
• Cigarette boxes that have aluminum
foil inside
• Metallic wallets or bags
• Coins
• Hand warmers made of metal
• Media such as CDs and DVDs
OWhen other wireless key (that emits
radio waves) is being used nearby
OWhen carrying the electronic key
together with the following devices
that emit radio waves
• Portable radio, cellular phone, cord-
less phone or other wireless commu-
nication devices
• Another electronic key or a wireless
key that emits radio waves
• Personal computers or personal digi-
tal assistants (PDAs)
• Digital audio players
• Portable game systems
OIf window tint with a metallic content or
metallic objects are attached to the
rear window
OWhen the electronic key is placed
near a battery charger or electronic
devices
OWhen the vehicle is parked in a pay
parking spot where radio waves are
emitted.
If the doors cannot be locked/unlocked
using the smart entry & start system,
lock/unlock the doors by performing any
of the following:
OBring the electronic key close to either
front door handle and operate the
entry function.
OOperate the wireless remote control. If
the doors cannot be locked/unlocked
using the above methods, use the mechanical key. (P.202)
If the hybrid system cannot be started
using the smart entry & start system,
refer to P.545.
QNote for the entry function
OEven when the electronic key is within
the effective range (detection areas),
the system may not operate properly
in the following cases:
• The electronic key is too close to the
window or outside door handle, near
the ground, or in a high place when
the doors are locked or unlocked.
• The electronic key is on the instru-
ment panel, luggage cover or floor, or
in the door pockets or glove box when
the hybrid system is started or power
switch modes are changed.
ODo not leave the electronic key on top
of the instrument panel or near the
door pockets when exiting the vehicle.
Depending on the radio wave recep-
tion conditions, it may be detected by
the antenna outside the cabin and the
door will become lockable from the
outside, possibly trapping the elec-
tronic key inside the vehicle.
OAs long as the electronic key is within
the effective range, the doors may be
locked or unlocked by anyone. How-
ever, only the doors detecting the
electronic key can be used to lock or
unlock the vehicle.
OEven if the electronic key is not inside
the vehicle, it may be possible to start
the hybrid system if the electronic key
is near the window.
OThe doors may unlock if a large
amount of water splashes on the door
handle, such as in the rain or in a car
wash when the electronic key is within
the effective range. (The doors will
automatically be locked after approxi-
mately 30 seconds if the doors are not
opened and closed.)
OIf the wireless remote control is used
to lock the doors when the electronic
key is near the vehicle, there is a pos-
sibility that the door may not be

2244-2. Opening, closing and locking the doors
unlocked by the entry function. (Use
the wireless remote control to unlock
the doors.)
OTouching the door lock sensor while
wearing gloves may delay or prevent
lock operation. Remove the gloves
and touch the lock sensor again.
OWhen the lock operation is performed
using the lock sensor, recognition sig-
nals will be shown up to two consecu-
tive times. After this, no recognition
signals will be given.
OIf the door handle becomes wet while
the electronic key is within the effec-
tive range, the door may lock and
unlock repeatedly. In that case, follow
the following correction procedures to
wash the vehicle:
• Place the electronic key in a location 2
m (6 ft.) or more away from the vehi-
cle. (Take care to ensure that the key
is not stolen.)
• Set the electronic key to battery-sav-
ing mode to disable the smart entry &
start system. (P.222)
OIf the electronic key is inside the vehi-
cle and a door handle becomes wet
during a car wash, a message may be
shown on the multi-information dis-
play and a buzzer will sound outside
the vehicle. To turn off the alarm, lock
all the doors.
OThe lock sensor may not work prop-
erly if it comes into contact with ice,
snow, mud, etc. Clean the lock sensor
and attempt to operate it again, or use
the lock sensor on the lower part of
the door handle.
OA sudden approach to the effective
range or door handle may prevent the
doors from being unlocked. In this
case, return the door handle to the
original position and check that the
doors unlock before pulling the door
handle again.
OIf there is another electronic key in the
detection area, it may take slightly lon-
ger to unlock the doors after the door
handle is gripped.
QWhen the vehicle is not driven for
extended periods
OTo prevent theft of the vehicle, do not
leave the electronic key within 2 m (6
ft.) of the vehicle.
OThe smart entry & start system can be
deactivated in advance. (P.573)
OBattery-saving mode can reduce the
power consumption of electronic keys.
(P.222)
QTo operate the system properly
Make sure to carry the electronic key
when operating the system. For vehicles
with entry function, do not get the elec-
tronic key too close to the vehicle when
operating the system from the outside of
the vehicle.
Depending on the position and holding
condition of the electronic key, the key
may not be detected correctly and the
system may not operate properly. (The
alarm may go off accidentally, or the
door lock prevention may not operate.)
QIf the smart entry & start system
does not operate properly
OLocking and unlocking the doors: Use
the mechanical key. (P.545)
OStarting the hybrid system: P.273
QCustomization
Settings (e.g. smart entry & start sys-
tem) can be changed.
(Customizable features: P.573)
If the smart entry & start system has
been deactivated in a customized set-
ting, refer to the explanations for the fol-
lowing operations.
OLocking and unlocking the doors:
Use the wireless remote control or
mechanical key. (P.203, 545)
OStarting the hybrid system and chang-
ing power switch modes: P.545
OStopping the hybrid system: P.275

2304-3. Adjusting the seats
will be overwritten.
QRecall procedure
1 Check that the shift lever is in P.
2 Turn the power switch to ON.
3 Press one of the buttons for the
driving position you want to
recall until the buzzer sounds.
QTo stop the position recall opera-
tion part-way through
Perform any of the following:
OPress the “SET” button.
OPress button “1” or “2”.
OOperate any of the seat adjustment switches.
QSeat positions that can be memo-
rized ( P.226)
The adjusted positions other than the position adjusted by lumbar support
switch can be recorded.
QOperating the driving position
memory after turning the power switch to OFF
Recorded seat positions can be acti-
vated up to 180 seconds after the driver’s door is opened and another 60 seconds after it is closed again.
QIn order to correctly use the driving
position memory function
If a seat position is already in the fur- thest possible position and the seat is
operated in the same direction, the recorded position may be slightly differ-ent when it is recalled.
QWhen recalling the driving position
Take care when recalling the driving position so that the head restraint does not touch the ceiling.
QIf the 12-volt battery is discon-
nected
The memorized positions are erased.
QRegistering procedure
Record your driving position to but-
ton “1” or “2” before performing the
following:
Carry only the key you want to reg-
ister, and then close the driver’s
door.
If 2 or more keys are in the vehicle,
the driving position cannot be
WARNING
QSeat adjustment caution
Take care during seat adjustment so that the seat does not strike the rear passenger or squeeze your body
against the steering wheel.
Registering/recall/canceling
an electronic key to driving
position (memory recall
function)

249
4
4-5. Opening, closing the windows and moon roof
Before driving
This function can be used to pre-
vent children from accidentally
opening or closing a passenger
window.
Press the switch.
The indicator will come on and the
passenger windows will be locked.
The passenger windows can still be
opened and closed using the driver’s
switch even if the lock switch is on.
QThe window lock switch can be operated when
The power switch is in ON.
QWhen the 12-volt battery is discon- nected
The window lock switch is disabled. If
necessary, press the window lock switch after reconnecting the 12-volt battery.
WARNING
OWhen exiting the vehicle, turn the power switch to OFF, carry the key
and exit the vehicle along with the child. There may be accidental operation, due to mischief, etc., that
may possibly lead to an accident.
QJam protection function
ONever use any part of your body to intentionally activate the jam pro-tection function.
OThe jam protection function may not work if something gets jammed just
before the side window is fully closed. Be careful not to get any part of your body jammed in the
side window.
QCatch protection function
ONever use any part of your body or clothing to intentionally activate the catch protection function.
OThe catch protection function may not work if something gets caught
just before the side window is fully opened. Be careful not to get any part of your body or clothing caught
in the side window.
Preventing accidental oper-
ation (window lock switch)
A

2745-2. Driving procedures
QWhen the ambient temperature is
low, such as during winter driving
conditions
OWhen starting the hybrid system, the
flashing time of the “READY” indicator
may be long. Leave the vehicle as it is
until the “READY” indicator is steady
on, as steady means the vehicle is
able to move.
OWhen the hybrid battery (traction bat-
tery) is extremely cold (below approxi-
mately -30°C [-22°F]) under the
influence of the outside temperature, it
may not be possible to start the hybrid
system. In this case, try to start the
hybrid system again after the tem-
perature of the hybrid battery
increases due to the outside tempera-
ture increase etc.
QSounds and vibrations specific to a
Plug in Hybrid Electric Vehicle
P.91
QIf the 12-volt battery is discharged
The hybrid system cannot be started
using the smart entry & start system.
Refer to P.546 to restart the hybrid sys-
tem.
QElectronic key battery depletion
P.200
QConditions affecting operation
P.222
QNote for the entry function
P.223
QSteering lock function
OAfter turning the power switch to OFF
and opening and closing the doors,
the steering wheel will be locked due
to the steering lock function. Operat-
ing the power switch again automati-
cally cancels the steering lock.
OWhen the steering lock cannot be
released, “Push Power Switch while
Turning Steering Wheel in Either
Direction” will be displayed on the
multi-information display.
Check that the shift lever is set in P.
Press the power switch shortly and firmly while turning the steering wheel
left and right.
OTo prevent the steering lock motor
from overheating, the motor may be
suspended if the hybrid system is
turned on and off repeatedly in a short
period of time. In this case, refrain
from operating the power switch. After
about 10 seconds, the steering lock
motor will resume functioning.
QIf there is a malfunction in the
smart entry & start system
If “Smart Entry & Start System Malfunc-
tion” is displayed on the multi-informa-
tion display, the system may be
malfunctioning. Have the vehicle
inspected by any authorized Toyota
retailer or Toyota authorized repairer, or
any reliable repairer immediately.
QIf the “READY” indicator does not
come on
In the event that the “READY” indicator
does not come on even after performing
the proper procedures for starting the
vehicle, contact any authorized Toyota
retailer or Toyota authorized repairer, or
any reliable repairer immediately.
QIf the hybrid system is malfunction-
ing
P.99
QElectronic key battery
P.486
QOperation of the power switch
OIf the switch is not pressed shortly and
firmly, the power switch mode may not
change or the hybrid system may not
start.
OIf attempting to restart the hybrid sys-
tem immediately after turning the

415
6
6-1. Using the air conditioning system and defogger
Interior features
OThe outside temperature is extremely
low
OWhen the hybrid system is cool (for
example, after being left for a long time in low temperatures)
QWindshield defogger
When defogging the windshield using
the Remote Air Conditioning System, defogging may be insufficient due to the power being restricted more than during
normal air conditioning operation. Also, the outside of the windshield may fog up due to the outside temperature, humidity
or air conditioning set temperature.
QUsing the heater via the Remote Air Conditioning System
OWhen the outside temperature is low, heating may feel insufficient due to restricted operation of the air condi-
tioning.
OWhen the outside heat exchanger
becomes frosted over, heating perfor- mance may decline due to automati-cally switching to the frost removal
operation. ( P.406)
QSecurity feature
Any unlocked doors will be automatically locked when the system is operating.
The emergency flashers flash to indicate that the doors have been locked or the system has been turned off.
QConditions affecting operation
 P.222
QWhile the Remote Air Conditioning System is operating
ODepending on the operating condition of the Remote Air Conditioning Sys-tem, the air conditioning compressor
or cooling fan may spin and an operat- ing noise may be heard.However, this does not indicate a mal-
function.
OThe air conditioning operation
switches, etc. will not operate while the Remote Air Conditioning System is operating.
QElectronic key battery depletion
 P.200
QWhen the electronic key battery is fully depleted
 P.486
QCustomization
Setting (e.g. Operation using “A/C” on the wireless remote control) can be changed. (Customizable features:
 P.569)
WARNING
QPrecautions for the Remote Air Conditioning System
ODo not use the system if people are in the vehicle. Even when the system is in use, the
internal temperature may still reach a high or low level due to features such as the automatic shut-off.
Children and pets left inside the vehicle may suffer heatstroke dehy-dration or hypothermia, or could
result in death or serious injury.
ODepending on the surrounding envi-
ronment, signals from the wireless switch may transmit further than expected. Pay appropriate attention
to the vehicle’s surroundings and use the switch only when neces-sary.
ODo not operate “A/C” on the wire-less remote control if the hood is
open. The air conditioning may operate unintentionally and objects may be drawn into the electrical
cooling fan.
NOTICE
QTo prevent the hybrid battery (traction battery) from being dis-charged
Use “A/C” on the wireless remote control only when necessary.