2022 TOYOTA GR86 engine

902-1. Instrument cluster
tor is disabled. The setting can be ena-
bled/disabled on of the
multi-information display. ( P.377)
The engine speed at which the REV
indicator is displayed can be changed
on of the multi-information display.
( P.377)
■Outside temperature display
●In the following situations, the correct
outside temperature may not be dis- played, or the display may take longer
than normal to change:
• When stopped, or driving at low speeds (less than 20 km/h [12 mph])
• When the outside temperature has
changed suddenly (at the entrance/exit of a garage, tunnel, etc.)
●When “--” is displayed, the system may be malfunctioning.
Take your vehicle to any authorized
Toyota retailer or Toyota authorized repairer, or any reliable repairer.
■Liquid crystal display
 P. 9 3
■Customization
The meter display ca n be customized on
the multi-information display. ( P.377)
■Changing the display
Press the display change button
until the desired item is displayed.
WA R N I N G
■The information display at low
temperatures
Allow the interior of the vehicle to warm up before using the liquid crys-
tal information display. At extremely
low temperatures, the information dis- play monitor may respond slowly, and
display changes may be delayed.
For example, there is a lag between
the driver’s shifting and the new gear number appearing on the display.
This lag could cause the driver to
downshift again, causing rapid and excessive engine braking and possi-
bly an accident resulting in death or
injury.
NOTICE
■To prevent damage to the engine
and its components
●Do not let the indicator needle of
the tachometer enter the red zone,
which indicates the maximum
engine speed.
●Pay extra attention to the engine
speed when the engine is cold, as the red zone will be lower than nor-
mal.
●If the engine coolant temperature
gauge indicator is flashing, the
engine may be overheating. Imme- diately stop the vehicle in a safe
place, and check the engine after it
has cooled completely. ( P.362)
Odometer and trip meter
display

93
2
2-1. Instrument cluster
Vehicle status information and indicators
( P.183)
Warning or advice pop-up displays
are also displayed in certain situa-
tions.
Engine coolant temperature
( P.88)
Engine oil temperature
Displays the engine oil temperature.
Fastest lap time
Refer to P.97 for the operating method.
Current lap time
Refer to P.97 for the operating method.
■Menu icons
Select a menu icon to display its
content.
*: Displayed when the navigation sys-
tem of Apple CarPlay or Android Auto
is operating. For details, refer to the
“Multimedia owner's manual”.
■Liquid crystal display
Small spots or light spots may appear on the display. This phenomenon is
characteristic of liq uid crystal displays,
and there is no problem continuing to use the display.
The multi-information display is
operated using the meter control
switches.
For information pertaining to the
content of each menu icon, refer to
the explanation of each item under
the heading of the relevant menu
icon.
Driving information ( P. 9 4 )
Sport information ( P. 9 5 )
Navigation system-linked dis-
play* ( P. 9 7 )
Audio system-linked display
( P. 9 7 )
Driving suppor t system infor-
mation display (if equipped)
( P. 9 8 )
Driving support system set-
ting display ( P. 9 8 )
A
C
D
Settings display (P. 9 8 )
Warning message display
( P.344)
WA R N I N G
■The multi-information display at
low temperatures
Allow the interior of the vehicle to warm up before using the liquid crys-
tal information display. At extremely
low temperatures, the information dis- play monitor may respond slowly, and
display changes may be delayed.
For example, there is a lag between the driver’s shifting and the new gear
number appearing on the display.
This lag could cause the driver to downshift again, causing rapid and
excessive engine braking and possi-
bly an accident resulting in death or injury.
Changing the meter display

942-1. Instrument cluster
/ : Select menu icons
/ : Change displayed con-
tent, scroll up/down the screen
and move the cursor
Press: Enter
Press and hold: Reset/change
scale of the G-force display
Return to the previous screen
■Display items
Press or of the meter con-
trol switch and select . Then
press or to display the fol-
lowing items:
 Driving information (page 1)
 Driving information (page 2)
 Driving information (page 3)
 Driving information (page 4)
■Driving information (page 1)
Use the display as a reference.
Voltmeter
Displays the char ging voltage.
As voltage displayed may be different
from the actual battery voltage, use the
voltmeter as a guideline.
Engine oil temperature gauge
Displays the engine oil temperature.
■Driving information (page 2)
Use the display as a reference.
Current fuel consumption
Displays the current rate of fuel con-
sumption.
Average fuel consumption
Displays the average fuel consumption
since the function was reset.
Driving range
Displays the estimated maximum dis-
tance that can be driven with the quan-
tity of fuel remaining.
This distance is computed based on
Content of driving informa-
tion
A
C
A
A
C

95
2
2-1. Instrument cluster
Vehicle status information and indicators
your average fuel consumption. As a
result, the actual distance that can be
driven may differ from that displayed.
When only a small amount of fuel is
added to the tank, the display may not
be updated. When refueling, turn the
engine switch off. If the vehicle is
refueled without turning the engine
switch off, the display may not be
updated.
■Driving information (page 3)
Use the display as a reference.
Average vehicle speed
Displays the average vehicle speed
since display was reset.
Driving time
Displays the cumulative time the vehi-
cle has been driven since display was
reset.
Driving distance
Displays the cumulative distance the
vehicle has been driven since display
was reset.
Pressing and hold ing will reset
the average vehicle speed/driving
time/driving distance.
■Driving information (page 4)
Displays each tire pressure.
( P.303)
■Display items
Press or of the meter con-
trol switch and select . Then
press or to display the fol-
lowing items:
 G-force
Suitable for confirming current lateral
G-forces on the vehicle.
 G-force (peak hold function)
Suitable for confirming the size and
direction of the maximum lateral
G-forces on the vehicle.
 Power and torque curve
 Stopwatch
■G-force
Displays lateral G-forces on the
vehicle.
Also displays, around the periph-
ery of the G-force display, the left
and right steering amount, acceler-
ator pedal input, and brake fluid
pressure.
This display is intended for use as a
guideline. Depending on factors
such as the road surface condition,
temperature and vehicle speed, the
display may not show the actual
condition of the vehicle.
A
C
Sport information

962-1. Instrument cluster
Acceleration G-force on the
vehicle
Accelerator pedal input
Brake fluid pressure
Steering amount
Press and hold to change the
range of the acceleration G-force
display between 1.0 G and 0.5 G.
■G-force (peak hold function)
Displays lateral G-forces on the
vehicle.
Also displays, around the periph-
ery of the G-force display, the left
and right steering amount, acceler-
ator pedal input, and brake fluid
pressure.
This display is intended for use as a
guideline. Depending on factors
such as the road surface condition,
temperature and vehicle speed, the
display may not show the actual
condition of the vehicle.
Record of the maximum
G-forces
Press and hold to reset the record
of maximum G-forces.
Acceleration G-force on the
vehicle
Accelerator pedal input
Brake fluid pressure
Steering amount
■Power and torque curve
This chart is intended for reference
only and does not show the actual
engine torque or output.
Power output
To r q u e
Current engine speed
The vertical bar will slide laterally
according to the current engine speed.
A
C
D
A
C
D
A
C

982-1. Instrument cluster
Select to display the operational
status of the Adaptive Cruise Con-
trol system ( P.185, 201)
The settings of the following sys-
tems can be changed.
 LDW (Lane Departure Warning)
(if equipped)
 PCB (Pre-Collision Braking) (if
equipped)
 BSD/RCTA (if equipped)
 RAB (Reverse Automatic Brak-
ing system) (if equipped)
 (Sonar Audible Alarm) (if
equipped)
 SRH (Steering Responsive
Headlight) (if quipped)
■Meter display settings that can
be changed
 Units (if equipped)
Select to change the units of measure
displayed.
 Startup Scrn
Select to enable/disable the startup
screen when the engine switch is
turned to ON.
 GSI (if equipped)
Select to enable/disable the shift posi-
tion indicator and shift-up indicator.
 REV. (REV indicator)
• Select to enable/disable the rev indi-
cator.
• Select to enable/disable the sounding
of a buzzer when the REV indicator is
illuminated.
• Select to set the engine speed at
which the rev indicator (orange) will
begin to be displayed.
■Vehicle functions and settings
that can be changed
 P.377
■Suspension of the settings display
●Some settings cannot be changed while driving. When changing set-
tings, park the vehicle in a safe place.
●If a warning message is displayed,
operation of the settings display will
be suspended.
Driving support system
information display (if
equipped)
Driving support system set-
ting display
Settings display
WA R N I N G
■Cautions during setting up the display
As the engine needs to be running
during setting up the display, ensure that the vehicle is parked in a place
with adequate ventilation. In a closed
area such as a garage, exhaust gases including harmful carbon mon-
oxide (CO) may colle ct and enter the
vehicle. This may lead to death or a serious health hazard.
NOTICE
■While setting up the display
To prevent battery discharge, ensure that the engine is running while set-
ting up the display features.

1003-1. Key information
3-1.Key information
The following keys are provided
with the vehicle.
Electronic keys
• Operating the smart entry & start sys-
tem ( P.109)
• Operating the wireless remote control
function ( P.101)
Mechanical keys
Key number plate
■When riding in an aircraft
When bringing an electronic key onto an
aircraft, make sure you do not press any
buttons on the electronic key while inside the aircraft cabin. If you are carry-
ing an electronic key in your bag etc.,
ensure that the buttons are not likely to be pressed accidentally. Pressing a but-
ton may cause the electronic key to emit
radio waves that could interfere with the operation of the aircraft.
■Electronic key battery depletion
●The standard battery life is 1 to 2 years.
●If the battery becomes low, an alarm
will sound in the cabin and a message will be shown on the multi-information
display when the engine is stopped.
●To reduce key battery depletion when
the electronic key is to not be used for
long periods of time, set the electronic key to the battery-saving mode.
( P. 111 )
●As the electronic key always receives
radio waves, the battery will become
depleted even if the electronic key is not used. The following symptoms
indicate that the electronic key battery
may be depleted. Replace the battery when necessary. ( P.316)
• The smart entry & start system or the
wireless remote control does not oper- ate.
• The detection area becomes smaller.
• The LED indicator on the key surface does not turn on.
●To avoid serious deterioration, do not leave the electronic key within 1 m (3
ft.) of the following electrical appli-
ances that produce a magnetic field: •TVs
• Personal computers
• Cellular phones, cordless phones and battery chargers
• Recharging cellular phones or cord-
less phones • Table lamps
• Induction cookers
■Replacing the battery
 P. 3 1 6
■Confirmation of the registered key number
The number of keys already registered
to the vehicle can be confirmed. Ask any authorized Toyota retailer or Toyota
authorized repairer, or any reliable
repairer for details.
Keys
The keys
A
C
NOTICE
■To prevent key damage
●Do not drop the keys, subject them
to strong shocks or bend them.
●Do not expose the keys to high
temperatures for long periods of
time.

105
3
3-2. Opening, closing and locking the doors and trunk
Before driving
■Door lock switches (to
lock/unlock)
1 Locks both side doors
2 Unlocks both side doors
■Inside lock buttons (to
lock/unlock)
1 Locks the door
2 Unlocks the door
■Locking the doors from the outside without a key
1 Move the inside lock button to the
lock position.
2 Close the door while pulling the door
handle.
The door cannot be locked if the engine
switch is in ACC or ON, or the electronic
key is left inside the vehicle. However, the key may not be detected correctly
and the door may be locked.
■Door lock prevention function
This function prevents the doors from being locked if an electronic key is left
inside the vehicle.
■Customization
Some functions can be customized. ( P.377)
WA R N I N G
■When using the wireless remote
control and operating the power
windows
Operate the power window after
checking to make sure that there is no
possibility of any passenger having any of their body parts caught in the
window. Also, do not allow children to
operate the wireless remote control. It
is possible for children and other pas- sengers to get caught in the power
window.
Unlocking and locking the
doors from the inside