2022 TOYOTA GR86 engine oil

2966-3. Do-it-yourself maintenance
■Checking the engine oil
1 Park the vehicle on level
ground. After warming up the
engine and turning it off, wait
more than 5 minutes for the oil
to drain back into the bottom of
the engine.
2 Holding a rag under the end,
pull the dipstick out.
3 Wipe the dipstick clean.
4 Reinsert the dipstick fully.
5 Holding a rag under the end,
pull the dipstick out and check
the oil level.
When checking the oil, look at both
sides of the dipstick and use the lower measurement to determine the level of
oil.
6 Wipe the dipstick and reinsert it
fully.
Low
Full
■Checking the oil type and pre-
paring the item needed
Make sure to check the oil type and
prepare the items needed before
adding oil.
 Engine oil selection
 P.370
 Oil quantity (Low  Full)
1.0 L (1.1 qt., 0.9 Imp. qt.)
 Item
Clean funnel
■Adding engine oil
If the oil level is below or near the
low level mark, add engine oil of the
same type as that already in the
engine.
1 Remove the oil filler cap by turn-
ing it counterclockwise.
2 Add engine oil slowly, checking
the dipstick.
3 Install the oil filler cap by turning
it clockwise.
■Engine oil consumption
A certain amount of engine oil will be
consumed while driving. In the following situations, oil consumption may
increase, and engine oil may need to be A

297
6
6-3. Do-it-yourself maintenance
Maintenance and care
refilled in between oil maintenance inter-
vals.
●When the engine is new, for example
directly after purchasing the vehicle or after replacing the engine
●If low quality oil or oil of an inappropri-ate viscosity is used
●When driving at high engine speeds or with a heavy load, or when driving
while accelerating or decelerating fre-
quently
●When leaving the engine idling for a
long time, or when driving frequently through heavy traffic
The coolant level is satisfactory if it
is between the “FULL” and “LOW”
lines on the reservoir when the
engine is cold.
■Engine coolant reservoir
Reservoir cap
“FULL” line
“LOW” line
If the level is on or below the “LOW”
line, add coolant up to the “FULL” line.
( P.362)
■Coolant selection
Only use “TOYOTA Genuine 50/50
Pre-mixed Super Long Life Coolant BLUE” or a similar high quality ethylene
glycol based non-silicate, non-amine,
non-nitrite, and non-borate coolant with long-life hybrid organic acid technology.
WA R N I N G
■Used engine oil
●Used engine oil contains poten-
tially harmful contaminants which may cause skin disorders such as
inflammation and skin cancer, so
care should be taken to avoid pro- longed and repeated contact. To
remove used engine oil from your
skin, wash thoro ughly with soap and water.
●Dispose of used oil and filters only in a safe and acceptable manner.
Do not dispose of used oil and fil-
ters in household trash, in sewers or onto the ground. Call any author-
ized Toyota dealer or repairer, or
another duly qualified and equipped professional, service station or auto
parts store for information concern-
ing recycling or disposal.
●Do not leave used engine oil within
the reach of children.
NOTICE
■To prevent serious engine dam-
age
Check the oil level on a regular basis.
■When replacing the engine oil
●Be careful not to spill engine oil on
the vehicle components.
●Avoid overfilling, or the engine
could be damaged.
●Check the oil level on the dipstick
every time you refill the vehicle.
●Be sure the engine oil filler cap is
properly tightened.
Checking the coolant
A
C

3246-3. Do-it-yourself maintenance
and install it.
7 Install the clips.
WA R N I N G
■Replacing light bulbs
●Turn off the lights. Do not attempt to
replace the bulb immediately after
turning off the lights. The bulbs become very hot and may cause
burns.
●Do not touch the glass portion of
the light bulb with bare hands.
When it is unavoidable to hold the glass portion, use and hold with a
clean dry cloth to avoid getting
moisture and oils on the bulb. Also, if the bulb is scratched or dropped,
it may blow out or crack.
●Fully install light bulbs and any
parts used to secure them. Failure
to do so may result in heat damage, fire, or water entering the light unit.
This may damage the lights or
cause condensation to build up on the lens.
■When changing the rear fog light or back-up lights
●Stop the engine and wait until the
exhaust pipes and surrounding parts have cooled down suffi-
ciently. The lights are located near
the exhaust pipe and touching a hot exhaust pipe and surrounding parts
can cause burns.
■To prevent damage or fire
●Make sure bulbs are fully seated
and locked.
●Check the wattage of the bulb
before installing to prevent heat damage.

337
7
7-2. Steps to take in an emergency
When trouble arises
■Charging system warning light
■Low engine oil pressure warning light
■Malfunction indicator lamp
■SRS warning light (warning buzzer)
Warning lightDetails/Actions
Indicates a malfunction in the vehicle’s charging system
 Immediately stop the vehicle in a safe place and contact
any authorized Toyota retailer or Toyota authorized
repairer, or any reliable repairer.
Warning lightDetails/Actions
Indicates that the engine oil pressure is too low
 Immediately stop the vehicle in a safe place and contact
any authorized Toyota retailer or Toyota authorized
repairer, or any reliable repairer.
Warning lightDetails/Actions
Indicates a malfunction in:
 The electronic engine control system;
 The electronic throttle control system; or
 The electronic automatic transmission control system (if
equipped)
 Have the vehicle inspected by any authorized Toyota
retailer or Toyota authorized repairer, or any reliable
repairer immediately.
Warning lightDetails/Actions
Indicates a malfunction in:
 The SRS airbag system; or
 The seat belt pretensioner system
 P. 5 3

345
7
7-2. Steps to take in an emergency
When trouble arises
■If “Check Owner’s Manual” is dis-
played
●If the following messages are shown,
following the instructions, accordingly. • “High Coolant Temperature” ( P.362)
• “Transmission Oil Temperature”
( P.143)
●If any of the following messages are
shown on the multi-information dis- play, it may indicate a malfunction.
Have the vehicle inspected by any
authorized Toyota retailer or Toyota authorized repairer, or any reliable
repairer immediately.
• “EyeSight OFF” • “Headlights Disabled”
• “ABS”
• “Steering System” • “Vehicle Stability Control”
• “Transmission”
• “Low Tire Pressure” • “RAB Disabled”
• “BSD/RCTA Disabled”
• “Keyless Access System Disabled” • “Auto Headlight Leveler Disabled”
• “SRH Disabled”
• “Gasoline Particulate Filter”
●If any of the following messages are
shown on the multi-information dis- play, it may indicate a malfunction.
Immediately stop the vehicle and con-
tact any authorized Toyota retailer or Toyota authorized repairer, or any reli-
able repairer.
• “Brake System” • “Check Engine”
• “SRS Airbag System”
 Stop the vehicle in a safe place
on a hard, flat surface.
 Set the parking brake.
 Shift the shift lever to P (auto-
matic transmission) or R (manual
transmission).
 Stop the engine.
 Turn on the emergency flashers.
( P.326)
 Check the degree of the tire
damage.
A tire should only be repaired with
the emergency tire puncture repair
If you have a flat tire
Your vehicle is not equipped
with a spare tire, but instead is
equipped with an emergency
tire puncture repair kit.
A puncture caused by a nail or
screw passing through the tire
tread can be repaired tempo-
rarily with the emergency tire
puncture repair kit.
WA R N I N G
■If you have a flat tire
Do not continue driving with a flat tire.
Driving even a short distance with a flat tire can damage the tire and the
wheel beyond repair. Driving with a
flat tire may cause a circumferential groove on the side wall. In such a
case, the tire may explode when
using the emergency tire puncture repair kit, resulting in death or serious
injury.
Before repairing the vehicle

3708-1. Specifications
*: If unleaded gasoline with a Research Octane Number of 98 is not available,
unleaded gasoline with a Research Octane Number of 95 may be used with no
detriment to engine durability or driveability.
■Oil capacity (Drain and refill [Reference*])
*: The engine oil capacity is a reference quantity to be used when changing the
engine oil. Warm up and turn off the engine, wait more than 5 minutes, and check
the oil level on the dipstick.
■Engine oil selection
“Toyota Genuine Motor Oil” is used
in your Toyota vehicle. Use Toyota
approved “Toyota Genuine Motor
Oil” or equivalent to satisfy the fol-
lowing grade and viscosity.
Oil grade:
0W-20, 5W-20 and 5W-30:
API grade SL “Energy-Conserving”,
SM “Energy-Conserving”, SN
“Resource-Conserving” or SN
PLUS “Resource-Conserving”; or
ILSAC GF-5 multigrade engine oil
Recommended viscosity (SAE):
SAE 0W-20 is filled in to your Toyota
vehicle at manufacturing, and the
best choice for good fuel economy
and good starting in cold weather.
If SAE 0W-20 is not available, SAE
5W-20 oil may be used. However, it
must be replaced with SAE 0W-20
Fuel
Fuel type
When you find these types of fuel label at
the gas station, use only the fuel with one
of the following labels.
EU area: Unleaded gasoline conforming
to European standard EN228 only
Except EU area: Unleaded gasoline only
Research Octane Number98 or higher*
Fuel tank capacity (Reference)50 L (13.2 gal., 11.0 Imp. gal.)
Lubrication system
With filter5.0 L (5.3 qt., 4.4 Imp. qt.)
Without filter4.8 L (5.1 qt., 4.2 Imp. qt.)

371
8
8-1. Specifications
Vehicle specifications
at the next oil change.
Temperature range anticipated
before next oil change
Preferred
Oil viscosity (0W-20 is explained
here as an example):
• The 0W in 0W-20 indicates the
characteristic of the oil which
allows cold startab ility. Oils with a
lower value before the W allow
for easier starting of the engine
in cold weather.
• The 20 in 0W-20 indicates the
viscosity characteristic of the oil
when the oil is at high tempera-
ture. An oil with a higher viscos-
ity (one with a higher value) may
be better suited if the vehicle is
operated at high speeds, or
under extreme load conditions.
How to read oil container labels:
Either or both API registered marks
are added to some oil containers to
help you select the oil you should
use.
API Service Symbol
Top portion: “API SERVICE SN” means
the oil quality designation by American
Petroleum Institute (API).
Center portion: “SAE 0W-20” means
the SAE viscosity grade.
Lower portion: “Resource-Conserving”
means that the oil has fuel-saving and
environmental protection capabilities.
ILSAC Certification Mark
The International Lubricant Specifica-
tion Advisory Commi ttee (ILSAC) Certi-
fication Mark is displayed on the front of
the container.
A
A

3748-1. Specifications
*: The recommended oil grade is API GL-4. However, API GL-3 can also be used.
*1: Minimum pedal clearance when depressed with a force of 300 N (30 kgf, 67 lbf)
while the engine is running.
Carpet
Brake pedal
Pedal clearance
NOTICE
■Transmission fluid type
If oil other than “MT GEAR OIL LV 75W” is used, the following may be experi- enced:
●The overall performance and function of the transmission may be adversely affected.
●Rattling noises may occur during idling and fuel consumption may increase.
Never use different brands together.
Clutch
Pedal free play
Left-hand drive vehicles
4.3 16.4 mm (0.170.65 in.)
Right-hand drive vehicles
4.1 15.7 mm (0.160.62 in.)
Fluid typeSAE J1703 or FMVSS No.116 DOT 3
Brakes
Pedal clearance*174 mm (2.91 in.) Min.
Pedal free play0.51.5 mm (0.0200.059 in.)
Parking brake lever travel*27 - 8 clicks
Fluid typeSAE J1703 or FMVSS No.116 DOT 3 or SAE
J1704 or FMVSS No.116 DOT 4
A
C