2022 TOYOTA GR86 sensor

73
1
1-3. Emergency assistance
For safety and security
Implementing Regulation
Implementing Regulation Annex1 PART3 User InformationConformity
1. DESCRIPTION OF THE ECALL IN-VEHICLE SYSTEM
1.1.Overview of the 112-based eCall in-vehicle sys-
tem, its operation and functionalitiesO
1.2.
The 112-based eCall service is a public service
of general interest and is accessible free of
charge.
O
1.3.
The 112-based eCall in-vehicle system is acti-
vated by default. It is activated automatically by
means of in-vehicle sensors in the event of a
severe accident. It will also be triggered automat-
ically when the vehicle is equipped with a TPS
system which does not function in the event of a
severe accident.
O
1.4.
The 112-based eCall in-vehicle system can also
be triggered manually, if needed. Instructions for
manual activation of the system
O
1.5.
In the event of a critical system failure that would
disable the 112-based eCall in-vehicle system,
the following warning will be given to the occu-
pants of the vehicle:
Red indicator light will illuminate
O
2. INFORMATION ON DATA PROCESSING

801-4. Theft deterrent system
*: If equipped
Turn the engine switch off, have all
the passengers exit the vehicle and
ensure that both side doors are
closed.
Using the entry function: Touch the
sensor area on the outside door
handle.
Using the wireless remote control:
Press .
Double locking system*
Unauthorized access to the
vehicle is prevented by
disabling the door unlocking
function from both the interior
and exterior of the vehicle.
Vehicles employing this sys-
tem have labels on the side
windows.
Setting the double locking
system
WA R N I N G
■Double locking system precau-
tion
Never activate the double locking sys- tem when there are people in the
vehicle because both side doors can-
not be opened from inside the vehicle.

103
3
3-2. Opening, closing and locking the doors and trunk
Before driving
3-2.Opening, closing and locking the doors and trunk
■Smart entry & start system
Carry the electronic key to enable
this function.
1 Grip the door handle to unlock
the doors.
Vehicles with a double locking system:
Grip the driver’s door handle to unlock
the door. Grip the passenger’s door
handle to unlock both side doors.*
Make sure to touch the sensor on the
back of the handle.
The doors cannot be unlocked for 3
seconds after the doors are locked.
*: The door unlock settings can be
changed.
2 Touch the lock sensor (indenta-
tion on the side of the door han-
dle) to lock the doors.
Check that the door is securely locked.
■Wireless remote control
1 Locks driver’s door*1
Locks both side doors*2
Check that the door is securely locked.
Press and hold to close the windows.*3
2 Unlocks both side door*1
Unlocks both side doors*2
Pressing the button unlocks the driver’s
door. Pressing the button again within 3
seconds unlocks the other doors.*2
Press and hold to open the windows.*3
*1: Vehicles without a double locking
system
*2: Vehicles with a double locking sys-
tem
*3: These settings must be customized
at any authorized Toyota retailer or
Toyota authorized repairer, or any
reliable repairer.
■Side window open/close function linked to door operation
In order to make opening and closing
the doors easier, completely closed win- dows are linked to door operations.
Therefore, when a door is opened, its
window opens slightly. When a door is closed, its window closes completely.
However, if the batt ery has discharged
or is disconnected, this function will not operate. ( P.362)
Doors
Unlocking and locking the
doors from the outside

1043-2. Opening, closing and locking the doors and trunk
■Operation signals
The emergency flashers flash to indicate that the doors have been
locked/unlocked. (Locked: once;
Unlocked: twice)
■Security feature ( vehicles without a double locking system)
If a door is not opened within approxi-
mately 30 seconds after the vehicle is unlocked using the entry function or
wireless remote contro l, the security fea-
ture automatically locks the vehicle again.
■When the door cannot be locked by
the lock sensor on the surface of
the door handle
If the doors cannot be locked by touch-
ing the lock sensor with a finger, touch
the lock sensor with the palm of your hand.
If you are wearing gloves, remove them.
■Door lock buzzer
If an attempt to lock the doors using the
entry function or wireless remote control is made when a door is not fully closed,
a buzzer will sound continuously for 5
seconds. Fully close the door to stop the buzzer, and lock the doors again.
■Alarm (if equipped)
Locking the doors will set the alarm sys-
tem. ( P. 8 1 )
■Conditions affecting the operation
of the smart entry & start system or wireless remote control
 P. 111
■If the smart entry & start system or
the wireless remote control does not operate properly
Use the mechanical key and/or inside
lock buttons to lock and unlock the doors. ( P.357)
Replace the key battery with a new one
if it is depleted. ( P.316)
■If the battery is discharged
The doors cannot be locked and
unlocked using the smart entry & start
system or wireless remote control. Lock or unlock the doors using the mechani-
cal key. ( P.357)
■Customization
Some functions can be customized. ( P.377)
WA R N I N G
■To prevent an accident
Ensure that both side doors are prop-
erly closed while driving the vehicle. Failure to do so may result in a door
opening and an occupant being
thrown out of the vehicle, resulting in death or serious injury.
■When opening or closing a door
Check the surroundings of the vehicle
such as whether the vehicle is on an
incline, whether there is enough space for a door to open and whether
a strong wind is blowing. When open-
ing or closing the door, hold the door handle tightly to prepare for any
unpredictable movement.
■Side window open/close function
linked to door operation
Do not hold the upper edge of the side window when you close the door.
Otherwise, your fingers or hand may
be caught in the window.

1123-2. Opening, closing and locking the doors and trunk
switch modes are changed.
●Do not leave the electronic key on top
of the instrument panel or near the
door pockets when exiting the vehicle. Depending on the radio wave recep-
tion conditions, it may be detected by
the antenna outside the cabin and the doors will become lockable from the
outside, possibly trapping the elec-
tronic key inside the vehicle.
●As long as the electronic key is within
the effective range, the doors may be locked or unlocked by anyone. How-
ever, only the doors detecting the
electronic key can be used to unlock the vehicle.
●Even if the electronic key is not inside the vehicle, it may be possible to start
the engine if the electronic key is near
the window.
●The doors may unlock or lock if a
large amount of water splashes on the door handle, such as in the rain or in a
car wash, when the electronic key is
within the effective range. (The doors will automatically be locked after
approximately 30 seconds if the doors
are not opened and closed.)
●If the wireless remote control is used
to lock the doors when the electronic key is near the vehicle, there is a pos-
sibility that the door may not be
unlocked by the entry function. (Use the wireless remote control to unlock
the doors.)
●Touching the door lock or unlock sen-
sor while wearing gloves may prevent
lock or unlock operation.
●Vehicles without a double locking sys-
tem: When the lock operation is per-
formed using the lock sensor, recognition signals will be shown up to
three consecutive times. After this, no
recognition signals will be given.
●If the door handle becomes wet while
the electronic key is within the effec- tive range, the door may lock and
unlock repeatedly. In this case, follow
the following correction procedures to
wash the vehicle:
• Place the electronic key in a location 2 m (6 ft.) or more away from the vehi-
cle. (Take care to ensure that the key
is not stolen.) • Set the electronic key to battery-sav-
ing mode to disable the smart entry &
start system. ( P. 1 1 1 )
●If the electronic key is inside the vehi-
cle and a door handle becomes wet during a car wash, a message may be
shown on the multi-information dis-
play and a buzzer will sound outside the vehicle. To turn off the alarm, lock
both side doors.
●The lock sensor may not work prop-
erly if it comes into contact with ice,
snow, mud, etc. Clean the lock sensor and attempt to operate it again.
●A sudden handle operation or a han-dle operation immediately after enter-
ing the effective range may prevent
the doors from being unlocked. Touch the door unlock sensor and check that
the doors are unlocked before pulling
the door handle again.
●Unlocking the vehicle may take more
time if another electronic key is within the effective range.
■When the vehicle is not driven for
extended periods
●To prevent theft of the vehicle, do not
leave the electronic key within 2 m (6
ft.) of the vehicle.
●The smart entry & start system can be
deactivated in advance. ( P. 1 1 3 )
●Setting the electronic key to bat-
tery-saving mode helps to reduce key battery depletion. ( P. 1 1 1 )
■To operate the system properly
●Make sure to carry the electronic key
when operating th e system. Do not get the electronic key too close to the
vehicle when operating the system
from the outside of the vehicle.
Depending on the position and holding
condition of the electronic key, the key may not be detected correctly and the

153
4
4-3. Operating the lights and wipers
Driving
4-3.Operating the lights and wipers
Operating the switch turns
on the lights as follows:
1 The headlights, front posi-
tion/daytime running lights
( P.153) and all the lights listed
above turn on and off automati-
cally. (When the engine switch is
in ON.)
2 The front position, tail,
license plate and instrument
panel lights turn on.
3 The headlights and all lights
listed above (except daytime
running lights) turn on.
4 The daytime running lights
turn on. ( P.153)
■AUTO mode can be used when
The engine switch is in ON.
■Daytime running light system
To make your vehicle more visible to
other drivers during daytime driving, the daytime running lights turn on automati-
cally whenever the engine is started and
the parking brake is released with the
headlight switch off or in the posi-
tion. (Illuminate brighter than the front
position lights.) Daytime running lights are not designed for use at night.
●When the turn signal indicators are flashing, the daytime running light on
the side that the turn signals are flash-
ing will turn off.
●When the emergency flashers are
flashing, both daytime running lights will turn off.
■Headlight control sensor
In the following situations, the automatic
light control system may not operate correctly.
●When an object is placed on the sen-sor or something which blocks the
sensor is affixed to the windshield
●When the surrounding area is lit by light other than natural light
■Automatic light off system
●When the light switch is in or :
The headlights turn off automatically if the engine switch is turned off.
●When the light switch is in : The
headlights and all lights turn off auto-
matically if the engine switch is turned
off.
Headlight switch
The headlights can be oper-
ated manually or automatically.
Operating instructions

2264-6. Using other driving systems
4-6.Using other driving systems
*: If equipped
BSD/RCTA consists of the following
functions.
 To detect a vehicle in a blind spot
on an adjacent lane or a vehicle
approaching at high speed while
driving the vehicle (Blind Spot
Detection)
 To detect a vehicle approaching
from the right or left while revers-
ing the vehicle (Rear Cross Traf-
fic Alert)
The system uses radar sensors for
the following features.
The BSD/RCTA radar sensor is approved under the radio wave related
laws of each country. For details, refer to
P.398.
■Blind Spot Detection (BSD)
The system notifies the driver of the
presence of vehicles in its blind
spot.
 If the system detects a vehicle in
its blind spot, it warns the driver
by illuminating the BSD/RCTA
approach indicator(s) on the out-
side mirror(s).
 If the driver operates the turn sig-
nal lever in the direction where
the BSD/RCTA approach indica-
tor is illuminating, the system
warns the driver of dangers by
flashing the BSD/RCTA
approach indicator.
BSD/RCTA*
The BSD/RCTA consists of rear
corner radars with Blind Spot
Detection, Lane Change Assist
and Rear Cross Traffic Alert.
These functions of BSD/RCTA
are the systems that detect
objects and vehicles to the rear
and draw attention to the
driver when changing a lane or
when driving in reverse.
WA R N I N G
The driver is responsible for driving
safely. Always be sure to check the
surroundings with your eyes when changing lanes or reversing the vehi-
cle.
The system is designed to assist the
driver in changing lanes or reversing
safely by monitoring the rear and side areas of the vehicle. However, you
cannot rely on this system alone in
assuring the safety during a lane change or reversing. Overconfidence
in this system could result in an acci-
dent and lead to serious injury or death. Since the system operation
has various limitations, the flashing or
illumination of the BSD/RCTA approach indicator may be delayed or
it may not operate at all even when a
vehicle is present in a neighboring lane or approaching from either side.
The driver is responsible for paying attention to the rear and side areas of
the vehicle.
System features

2284-6. Using other driving systems
1The detection range of the radar
sensors
2 Area out of detection range of
the radar sensors
Parked vehicle
Vehicle that may not be
detected
Example 2
1 The detection range of the radar
sensors
Vehicle that may be detected
The system may detect that a vehicle
is passing in front of your vehicle.
Always be sure to check the
surroundings with your eyes when reversing the vehicle.
■Operating conditions
The BSD/RCTA will operate when
all of the following conditions are
met.
 The engine switch is in ON.
 The BSD/RCTA warning light
and BSD/RCTA OFF indicator
are turned off.
 The vehicle is driven at speeds
above 12 km/h (7 mph) (except
when reversing).
 The shift lever is in R. (RCTA
only)
The BSD/RCTA will not operate in
the following situations.
 The BSD/RCTA OFF indicator
appears.
 The vehicle speed is below 10
km/h (6 mph) even when the
BSD/RCTA OFF indicator does
not appear (except when revers-
ing).
●In the following cases, the BSD/RCTA
will stop operating and the BSD/RCTA warning light will appear.
• When a malfunction occurs in the sys-
tem, including the BSD/RCTA approach indicator
●If the BSD/RCTA warning light appears, exercise proper caution.
( P.232)
●In the following cases, the BSD/RCTA
will temporarily stop operating (or may
stop operating) and the BSD/RCTA
WA R N I N G
An approaching vehicle may not
be detected because the detection
range is limited by the parked vehicle
. Always be sure to check the
surroundings with your eyes when
reversing the vehicle.
A
C
System operation