2022 TOYOTA GR86 remote start

1123-2. Opening, closing and locking the doors and trunk
switch modes are changed.
●Do not leave the electronic key on top
of the instrument panel or near the
door pockets when exiting the vehicle. Depending on the radio wave recep-
tion conditions, it may be detected by
the antenna outside the cabin and the doors will become lockable from the
outside, possibly trapping the elec-
tronic key inside the vehicle.
●As long as the electronic key is within
the effective range, the doors may be locked or unlocked by anyone. How-
ever, only the doors detecting the
electronic key can be used to unlock the vehicle.
●Even if the electronic key is not inside the vehicle, it may be possible to start
the engine if the electronic key is near
the window.
●The doors may unlock or lock if a
large amount of water splashes on the door handle, such as in the rain or in a
car wash, when the electronic key is
within the effective range. (The doors will automatically be locked after
approximately 30 seconds if the doors
are not opened and closed.)
●If the wireless remote control is used
to lock the doors when the electronic key is near the vehicle, there is a pos-
sibility that the door may not be
unlocked by the entry function. (Use the wireless remote control to unlock
the doors.)
●Touching the door lock or unlock sen-
sor while wearing gloves may prevent
lock or unlock operation.
●Vehicles without a double locking sys-
tem: When the lock operation is per-
formed using the lock sensor, recognition signals will be shown up to
three consecutive times. After this, no
recognition signals will be given.
●If the door handle becomes wet while
the electronic key is within the effec- tive range, the door may lock and
unlock repeatedly. In this case, follow
the following correction procedures to
wash the vehicle:
• Place the electronic key in a location 2 m (6 ft.) or more away from the vehi-
cle. (Take care to ensure that the key
is not stolen.) • Set the electronic key to battery-sav-
ing mode to disable the smart entry &
start system. ( P. 1 1 1 )
●If the electronic key is inside the vehi-
cle and a door handle becomes wet during a car wash, a message may be
shown on the multi-information dis-
play and a buzzer will sound outside the vehicle. To turn off the alarm, lock
both side doors.
●The lock sensor may not work prop-
erly if it comes into contact with ice,
snow, mud, etc. Clean the lock sensor and attempt to operate it again.
●A sudden handle operation or a han-dle operation immediately after enter-
ing the effective range may prevent
the doors from being unlocked. Touch the door unlock sensor and check that
the doors are unlocked before pulling
the door handle again.
●Unlocking the vehicle may take more
time if another electronic key is within the effective range.
■When the vehicle is not driven for
extended periods
●To prevent theft of the vehicle, do not
leave the electronic key within 2 m (6
ft.) of the vehicle.
●The smart entry & start system can be
deactivated in advance. ( P. 1 1 3 )
●Setting the electronic key to bat-
tery-saving mode helps to reduce key battery depletion. ( P. 1 1 1 )
■To operate the system properly
●Make sure to carry the electronic key
when operating th e system. Do not get the electronic key too close to the
vehicle when operating the system
from the outside of the vehicle.
Depending on the position and holding
condition of the electronic key, the key may not be detected correctly and the

113
3
3-2. Opening, closing and locking the doors and trunk
Before driving
system may not operat e properly. (The
alarm may go off accidentally, or the door lock prevention function may not
operate.)
●Do not leave the electronic key inside
the trunk.
The key confinement prevention func- tion may not operate, depending on
the location of the key (the inside
edge of the Trunk), conditions (inside a metal bag, close to metallic objects)
and the radio waves in the surround-
ing area. ( P.109)
■If the smart entry & start system does not operate properly
●Locking and unlocking the doors:  P. 3 5 7
●Starting the engine: P. 3 5 8
■Customization
Some functions can be customized.
( P.377)
■If the smart entry & start system
has been disabled
●Locking and unlocking the doors:
Use the wireless remote control or mechanical key. ( P.103, 357)
●Starting the engine and changing engine switch modes: P. 3 5 8
●Stopping the engine: P. 1 4 1
In the following situations, the
smart entry & start system should
be disabled.
 When people with implantable
cardiac pacemakers, cardiac
resynchronization therapy pace-
WA R N I N G
■Caution regarding interference
with electronic devices
●People with implantable cardiac pacemakers, cardiac
resynchronization therapy-pace-
makers or implantable cardioverter defibrillators should maintain a rea-
sonable distance between them-
selves and the smart entry & start
system antennas. ( P.110) The radio waves may affect the
operation of such devices. If neces-
sary, the entry function can be disa- bled. Ask any authorized Toyota
retailer or Toyota authorized
repairer, or any reliable repairer for details, such as the frequency of
radio waves and timing of the emit-
ted radio waves. Then, consult your doctor to see if you should disable
the entry function.
●Users of any electrical medical
device other than implantable car-
diac pacemakers, cardiac resynchronization therapy-pace-
makers or implantable cardioverter
defibrillators should consult the manufacturer of the device for infor-
mation about its operation under
the influence of radio waves. Radio waves could have unex-
pected effects on the operation of
such medical devices.
The smart entry & start system can be
disabled. ( P.113)
When to disable the smart
entry & start system

1143-2. Opening, closing and locking the doors and trunk
makers or implantable
cardioverter defibr illators ride in
the vehicle.
 When the vehicle will not be
used for a long time, or the smart
entry & start system is not used.
 When storing an electronic key
near or inside the vehicle cannot
be avoided.
When the smart entry & start sys-
tem is disabled, use the wireless
remote control to lock and unlock
the doors.
When starting the en gine, it will be
necessary to hold the electronic
key near the engine switch.
( P.358)
■Disabling the smart entry &
start system
The smart entry & start system can
be disabled by opening and closing
the doors or using the wireless
remote control.
Door opening/closing method
1 While sitting in the driver’s seat,
close the door.
2 Press of the door lock
switch.
3 Within 5 seconds of performing
step 2, open the driver’s door.
4 Within 5 seconds of performing
step 3, press of the door
lock switch 2 times with the door
open.
5 Within 10 seconds of performing
step 4, close and open the
driver’s door 2 times.
6 Within 10 seconds of performing
step 5, press of the door
lock switch 2 times with the door
open.
7 Within 10 seconds of performing
step 6, close and open the
driver’s door 1 time.
8 Within 5 seconds of performing
step 7, close the driver’s door.
A buzzer will sound for approximately 2
seconds and the smart entry & start
system will be disabled.
Wireless remote control method
1 Open the driver’s door and push
the lock lever forward.
2 Press and hold and of
the wireless remote control at
the same time for 5 seconds or
more.
A buzzer will sound for approximately 2
seconds and the smart entry & start
system will be disabled.
■Enabling the smart entry &
start system
The smart entry & start system can
be enabled by performing the pro-

115
3
3-2. Opening, closing and locking the doors and trunk
Before driving
cedure used to disable it again.
When enabled a buzzer will sound.
■Door opening/closing method
Make sure to firmly press the door lock
switch in steps 4 and 6. If the switch is
pressed for a very short time, the sys- tem may not be disabled.
■Wireless remote control method
To use the wireless remote control
method to disable the smart entry & start system, it is necessary to register a PIN
code for the PIN code smart entry.
( P.115)
■When enabling the smart entry & start system
If the method used to disable the smart
entry & start system is unknown, press the engine switch.
●If the wireless remo te control system was used, a buzzer inside the vehicle
will sound.
●If the door opening/closing method
was used, the buzzer will not sound.
■Customization
Some functions can be customized. ( P.377)
By registering a 5 digit PIN code, all
of the doors and the fuel filler door
can be unlocked without an elec-
tronic key by pressing the trunk
opener switch.
■PIN code registration method
1 Turn the engine switch off.
2 Close all of the doors and the
trunk.
3 Press and hold of the wire-
less remote control.
At this time, all of the doors and the fuel filler door will lock.
4 Within 5 seconds of performing
step 3, press and hold the trunk
opener switch.
After 5 seconds or more, a buzzer will sound.
5 Release of the wireless
remote control and the trunk
opener switch.
6 Within 30 seconds after the
buzzer begins sounding, press
of the wireless remote con-
trol.
The buzzer will stop.
7 A PIN code can now be regis-
tered. Press the trunk opener
switch the same number of
times as the first digit of the PIN
code.
For example: If registering 32468, press the switch 3 times.
NOTICE
■When disabling the smart entry &
start system
When disabling or enabling the sys- tem to accommodate persons with
implantable cardiac pacemakers, car-
diac resynchronization therapy pace- makers or implantable cardioverter
defibrillators, always use the door
opening/closing method. If the wire- less remote control method is used,
the system may be enabled acciden-
tally.
Unlocking the doors using
PIN code smart entry

1163-2. Opening, closing and locking the doors and trunk
8Wait for the buzzer to sound 1
time and then press the switch
the same number of times as for
the next digit.
For example: If registering 32468,
press the switch 2 times.
9 Repeat step 8 for the remaining
digits.
10 Within 30 seconds after the
buzzer begins sounding inter-
mittently, perform steps 7
through 9 again to confirm the
PIN code.
Registration is complete and all of the doors and the fuel filler door will unlock.
■Unlocking method
Press the trunk opener switch using
the same procedure as steps 7
through 9.
■PIN code registration
●To prevent theft, the same digit for all
5 digits and 12345 cannot be regis- tered as the PIN code. Also, avoid
using the same number as on your
license plate or other simple codes.
●To use 0 as a digit, press the trunk
opener switch 10 times.
●If a mistake is made during registra-
tion, unlock the doors or trunk using
the wireless remote control to cancel registration. Then perform registra-
tion again, starting from step 1. How-
ever, if the mistake was made in step 10 , a buzzer will sound and step 10
can be performed again.
●To clear the PIN code, perform the
registration procedure and enter
22222.
●After registering a new PIN code,
make sure to check that the doors can be unlocked using the code.
●If the smart entry & start system has
been disabled using the wireless
remote control method, the PIN code for the PIN code smart entry cannot
be cleared. ( P.114)
●In the following cases, perform the
PIN code registration procedure
again. • If the PIN code has been forgotten.
• When you wish to change the PIN
code.
●Make sure to change the PIN code
periodically.
●If the vehicle has been loaned to
another person, make sure that the PIN code has not been changed or
cleared. If the PIN code has been
changed or cleared, perform PIN code registration again.
■Unlocking method
●If an electronic key is within a detec-tion area, operation of the smart entry
will be given priority.
●If a mistake is made while entering the
PIN code, wait 5 seconds or more
before performing the procedure again.
●If the incorrect PIN code is entered 5 times consecutively, a buzzer will
sound for approximately 2 seconds
and operation will not be possible for 5 minutes.

1263-5. Opening, closing the windows
3-5.Opening, closing the windows
The power windows can be opened
and closed using the switches.
Operating the switch moves the
windows as follows:
1 Closing
2 One-touch closing*
3Opening
4 One-touch opening*
*: To stop the window partway, operate
the switch in the opposite direction.
■The power windows can be oper-
ated when
The engine switch is in ON.
■Operating the power windows after
turning the engine off
The power windows can be operated for approximately 40 seconds after the
engine switch is turned to ACC or OFF.
They cannot, however, be operated once either front door is opened.
■Jam protection function
If an object becomes jammed between
the window and the body while the win- dow is closing, window movement is
stopped and the window is opened
slightly.
■Catch protection function
If an object becomes caught between the door and window while the window
is opening, window movement is
stopped.
■When the window cannot be opened or closed
When the jam protection function or
catch protection function operates unu- sually and the door window cannot be
opened or closed, perform the following
operations with the power window switch of that door.
1 Check that all of the doors are
closed.
2 Turn the engine switch to ON.
3 Press and hold the power window
switch in the one-touch opening position. After the window is fully
opened, continue pressing the
switch for approximately 1 second.
4 Pull and hold the power window switch in the one-touch closing posi-
tion. After the window is fully closed,
continue pulling the switch for approximately 1 second.
If you push the power window switch to
the opening position while the window is moving, start again from the beginning.
If the window continues to close but then
re-open slightly even after performing the above procedure correctly, have the
vehicle inspected by any authorized
Toyota dealer orrepairer, or another duly qualified and equipped professional.
■Door lock linked window operation
The power windows can be opened and
closed using the wireless remote con-
trol.* ( P.103)*: These settings must be customized at
any authorized Toyota retailer or
Toyota authorized repairer, or any reli-
able repairer.
■Customization
Some functions can be customized.
( P.377)
Power windows
Opening and closing the
power windows

155
4
4-3. Operating the lights and wipers
Driving
between the high beams and low
beams according to the conditions. If
the lever is pushed forward and
released again, the high beam assist
will turn off and the high beam head-
lights will turn on.
To manually turn the high beam head-
lights on, push and release the lever
with the headlight switch in posi-
tion. If the lever is pulled and released,
the high beam headlights will turn off
and the low beam headlights will turn
on.
2 Illuminate the high beam head-
lights while the lever is pulled
Even if the lights are off, the high beam
headlights will illuminate. When the
lever is released, the headlights will
return to the low beam headlights or will
turn off.
This system allows the headlights
to be turned on for approximately
30 seconds when the engine switch
is off.
Pull the lever toward you and
release it with the light switch in
or after turning the engine
switch off.
The lights are turned off in the fol-
lowing situations:
 The engine switch is turned to
ON.
 The light switch is turned on.
 The light switch is pulled toward
you and then released.
 The doors are unlocked using
the smart entry & start system or
wireless remote control.
■Customization
Some functions can be customized. ( P.377)
*: If equipped
The SRH (Steering Responsive
Headlights) is a function which,
according to the steering wheel
operation and vehicle speed when
the vehicle is being driven forward,
automatically adjusts the angle of
the headlights to illuminate inter-
sections and corners, improving
visibility.
This function operates when the vehicle
speed is 8 km/h or higher.
Extended Headlight Lighting
system
SRH (Steering Responsive
Headlights)*

299
6
6-3. Do-it-yourself maintenance
Maintenance and care
“UPPER LEVEL” line
“LOWER LEVEL” line
If the fluid level is at or below the
“LOWER LEVEL” line, add distilled
water.
■Adding distilled water
1 Remove the vent plug.
2 Add distilled water.
If the “UPPER LEVEL” line cannot be seen, check the fluid level by looking
directly at the cell.
3 Put the vent plug back on and
close it securely.
■Before recharging
When recharging, the battery produces
hydrogen gas which is flammable and
explosive. Therefore, observe the fol- lowing before recharging:
●If recharging with the battery installed on the vehicle, be sure to disconnect
the ground cable.
●Make sure the power switch on the
charger is off when connecting and disconnecting the charger cables to
the battery.
■After recharging/reconnecting the
battery
The engine may not start. Follow the
procedure below to initialize the system.
1 Shift the shift lever to P (automatic
transmission) or depress the brake pedal with the shift lever in N (man-
ual transmission).
2 Open and close either door.
3 Restart the engine.
●Unlocking the doors using the smart
entry & start system may not be possi-
ble immediately after reconnecting the battery. If this happens, use the wire-
less remote control or the mechanical
key to lock/unlock the doors.
●Start the engine with the engine
switch in ACC. The engine may not start with the engine switch turned off.
However, the engine will operate nor-
mally from the second attempt.
●The engine switch mode is recorded
by the vehicle. If the battery is discon- nected and reconnected, the vehicle
will return the engine switch mode to
the status it was in before the battery was disconnected. Make sure to turn
off the engine before disconnecting
the battery. Take extra care when con- necting the battery if the engine switch
mode prior to the battery being dis-
connected is unknown.
If the engine will not start even after mul-
tiple attempts, contact any authorized Toyota dealer or repairer, or another
duly qualified and equipped profes-
sional.
A