2022 TOYOTA GR86 battery

1043-2. Opening, closing and locking the doors and trunk
■Operation signals
The emergency flashers flash to indicate that the doors have been
locked/unlocked. (Locked: once;
Unlocked: twice)
■Security feature ( vehicles without a double locking system)
If a door is not opened within approxi-
mately 30 seconds after the vehicle is unlocked using the entry function or
wireless remote contro l, the security fea-
ture automatically locks the vehicle again.
■When the door cannot be locked by
the lock sensor on the surface of
the door handle
If the doors cannot be locked by touch-
ing the lock sensor with a finger, touch
the lock sensor with the palm of your hand.
If you are wearing gloves, remove them.
■Door lock buzzer
If an attempt to lock the doors using the
entry function or wireless remote control is made when a door is not fully closed,
a buzzer will sound continuously for 5
seconds. Fully close the door to stop the buzzer, and lock the doors again.
■Alarm (if equipped)
Locking the doors will set the alarm sys-
tem. ( P. 8 1 )
■Conditions affecting the operation
of the smart entry & start system or wireless remote control
 P. 111
■If the smart entry & start system or
the wireless remote control does not operate properly
Use the mechanical key and/or inside
lock buttons to lock and unlock the doors. ( P.357)
Replace the key battery with a new one
if it is depleted. ( P.316)
■If the battery is discharged
The doors cannot be locked and
unlocked using the smart entry & start
system or wireless remote control. Lock or unlock the doors using the mechani-
cal key. ( P.357)
■Customization
Some functions can be customized. ( P.377)
WA R N I N G
■To prevent an accident
Ensure that both side doors are prop-
erly closed while driving the vehicle. Failure to do so may result in a door
opening and an occupant being
thrown out of the vehicle, resulting in death or serious injury.
■When opening or closing a door
Check the surroundings of the vehicle
such as whether the vehicle is on an
incline, whether there is enough space for a door to open and whether
a strong wind is blowing. When open-
ing or closing the door, hold the door handle tightly to prepare for any
unpredictable movement.
■Side window open/close function
linked to door operation
Do not hold the upper edge of the side window when you close the door.
Otherwise, your fingers or hand may
be caught in the window.

109
3
3-2. Opening, closing and locking the doors and trunk
Before driving
■If the smart entry & start system or
the wireless remote control does not operate properly
Replace the key battery with a new one
if it is depleted. ( P.316)
■Customization
Some functions can be customized.
( P.377)
■Antenna location
Antennas outside the cabin
Antennas inside the cabin
Antenna outside the trunk
Antenna inside the trunk
Smar t entr y & start sys-
tem
The following operations can
be performed simply by carry-
ing the electronic key on your
person, for example in your
pocket. The driver should
always carry the electronic
key.
 Locks and unlocks the doors
( P.103)
 Opens the trunk (P. 1 0 8 )
 Starts the engine (P.139)
A
C
D

1103-2. Opening, closing and locking the doors and trunk
■Effective range (areas within which
the electronic key is detected)
When locking or unlocking the
doors
The system can be operated when the
electronic key is within about 0.4  0.8
m (1.3  2.6 ft.) of an outside door han-
dle. (Only the doors detecting the key
can be operated.)
When opening the trunk
The system can be operated when the
electronic key is within about 0.4  0.8
m (1.3  2.6 ft.) of the trunk release but-
ton.
When starting the engine or chang-
ing engine switch modes
The system can be operated when the
electronic key is inside the vehicle.
■Alarms and warning messages
An alarm sounds and warning mes- sages are displayed on the multi-infor-
mation display to protect against
unexpected accidents or theft of the vehicle resulting from erroneous opera-
tion. When a warning message is dis-
played, take appropriate measures based on the displayed message.
( P.344)
When only an alarm sounds, circum- stances and correction procedures are
as follows.
●When an exterior alarm sounds once
for 5 seconds
●When an exterior alarm sounds once
for 2 seconds
●When an interior alarm sounds contin-
uously
■Battery-saving function
The battery-saving function will be acti- vated in order to prevent the electronic
key battery and the vehicle battery from
being discharged while the vehicle is not
in operation for a long time.
●In the following situations, the smart
entry & start system may take some time to unlock the doors.
• The electronic key has been left within
approximately 2 m (6 ft.) of the outside of the vehicle for 10 minutes or longer.
A
C
SituationCorrection
procedure
An attempt was made
to lock the vehicle while
a door was open.
Close both
side doors
and lock the
doors again.
SituationCorrection
procedure
The trunk was closed
while the electronic key
was still inside the trunk
and both side doors
were locked.
Retrieve the
electronic key
from the trunk
and close the
trunk lid.
SituationCorrection
procedure
The engine switch was
turned to ACC while the
driver’s door was open
(or the driver’s door
was opened while the
engine switch was in
ACC).
Turn the
engine switch
off and close
the driver’s
door.
The engine switch was
turned off while the
driver’s door was open.
Close the
driver’s door.

111
3
3-2. Opening, closing and locking the doors and trunk
Before driving
• The smart entry & start system has
not been used for 5 days or longer.
●If the smart entry & start system has
not been used for 14 days or longer, the doors cannot be unlocked at the
passenger door. In this case, take
hold of the driver’s door handle, or use the wireless remote control or
mechanical key, to unlock the doors.
■Electronic Key Battery-Saving
Function
When battery-saving mode is set, bat-
tery depletion is minimized by stopping
the electronic key from receiving radio waves.
Press twice while pressing and
holding . Confirm that the electronic
key indicator flashes 4 times.
While the battery-saving mode is set,
the smart entry & start system cannot be
used. To cancel the function, press any
of the electronic key buttons.
■Conditions affecting operation
The smart entry & start system uses
weak radio waves. In the following situa- tions, the communication between the
electronic key and the vehicle may be
affected, preventing the smart entry &
start system, wireless remote control and engine immobilizer system from
operating properly. (Ways of coping:
 P.357)
●When the electronic key battery is
depleted
●Near a TV tower, electric power plant,
gas station, radio station, large dis- play, airport or other facility that gen-
erates strong radio waves or electrical
noise
●When carrying a portable radio, cellu-
lar phone, cordless phone or other
wireless communication device
●When the electronic key is in contact
with, or is covered by the following metallic objects
• Cards to which aluminum foil is
attached • Cigarette boxes that have aluminum
foil inside
• Metallic wallets or bags •Coins
• Hand warmers made of metal
• Media such as CDs and DVDs
●When other wirele ss keys (that emit
radio waves) are being used nearby
●When carrying the electronic key
together with the following devices that emit radio waves
• Another vehicle’s electronic key or a
wireless key that emits radio waves • Personal computers or personal digi-
tal assistants (PDAs)
• Digital audio players • Portable game systems
●If window tint with a metallic content or metallic objects are attached to the
rear window
●When the electronic key is placed
near a battery charger or electronic
devices
■Note for the entry function
●Even when the electronic key is within
the effective range (detection areas), the system may not operate properly
in the following cases:
• The electronic key is too close to the window or outside door handle, near
the ground, or in a high place when
the doors are locked or unlocked.
• The electronic key is near the ground or in a high place, or too close to the
rear bumper center when the trunk is
unlocked. • The electronic key is on the instru-
ment panel, rear package tray or floor,
or in the door pockets or glove box when the engine is started or engine

1123-2. Opening, closing and locking the doors and trunk
switch modes are changed.
●Do not leave the electronic key on top
of the instrument panel or near the
door pockets when exiting the vehicle. Depending on the radio wave recep-
tion conditions, it may be detected by
the antenna outside the cabin and the doors will become lockable from the
outside, possibly trapping the elec-
tronic key inside the vehicle.
●As long as the electronic key is within
the effective range, the doors may be locked or unlocked by anyone. How-
ever, only the doors detecting the
electronic key can be used to unlock the vehicle.
●Even if the electronic key is not inside the vehicle, it may be possible to start
the engine if the electronic key is near
the window.
●The doors may unlock or lock if a
large amount of water splashes on the door handle, such as in the rain or in a
car wash, when the electronic key is
within the effective range. (The doors will automatically be locked after
approximately 30 seconds if the doors
are not opened and closed.)
●If the wireless remote control is used
to lock the doors when the electronic key is near the vehicle, there is a pos-
sibility that the door may not be
unlocked by the entry function. (Use the wireless remote control to unlock
the doors.)
●Touching the door lock or unlock sen-
sor while wearing gloves may prevent
lock or unlock operation.
●Vehicles without a double locking sys-
tem: When the lock operation is per-
formed using the lock sensor, recognition signals will be shown up to
three consecutive times. After this, no
recognition signals will be given.
●If the door handle becomes wet while
the electronic key is within the effec- tive range, the door may lock and
unlock repeatedly. In this case, follow
the following correction procedures to
wash the vehicle:
• Place the electronic key in a location 2 m (6 ft.) or more away from the vehi-
cle. (Take care to ensure that the key
is not stolen.) • Set the electronic key to battery-sav-
ing mode to disable the smart entry &
start system. ( P. 1 1 1 )
●If the electronic key is inside the vehi-
cle and a door handle becomes wet during a car wash, a message may be
shown on the multi-information dis-
play and a buzzer will sound outside the vehicle. To turn off the alarm, lock
both side doors.
●The lock sensor may not work prop-
erly if it comes into contact with ice,
snow, mud, etc. Clean the lock sensor and attempt to operate it again.
●A sudden handle operation or a han-dle operation immediately after enter-
ing the effective range may prevent
the doors from being unlocked. Touch the door unlock sensor and check that
the doors are unlocked before pulling
the door handle again.
●Unlocking the vehicle may take more
time if another electronic key is within the effective range.
■When the vehicle is not driven for
extended periods
●To prevent theft of the vehicle, do not
leave the electronic key within 2 m (6
ft.) of the vehicle.
●The smart entry & start system can be
deactivated in advance. ( P. 1 1 3 )
●Setting the electronic key to bat-
tery-saving mode helps to reduce key battery depletion. ( P. 1 1 1 )
■To operate the system properly
●Make sure to carry the electronic key
when operating th e system. Do not get the electronic key too close to the
vehicle when operating the system
from the outside of the vehicle.
Depending on the position and holding
condition of the electronic key, the key may not be detected correctly and the

139
4
4-2. Driving procedures
Driving
4-2.Driving procedures
1 Check that the parking brake is
set.
2 Check that the shift lever is in P
(automatic transmission) or N
(manual transmission).
3 Firmly depress the brake pedal
(automatic transmission) or
clutch pedal (manual transmis-
sion).
, and a message will be dis- played on the multi-information display.
If it is not displayed, the engine cannot
be started.
4 Press the engine switch shortly
and firmly.
When operating the engine switch, one
short, firm press is enough. It is not necessary to press and hold the switch.
The engine will crank until it starts or for
up to 10 seconds, whichever is less.
Continue depressing the brake pedal
(automatic transmission) or clutch
pedal (manual transmission) until the engine is completely started.
The engine can be started from any
engine switch mode.
■If the engine does not start
●The engine immobilizer system may
not have been deactivated. ( P. 7 9 )
Contact any authorized Toyota retailer or Toyota authorized repairer, or any
reliable repairer.
●If a message related to start-up is
shown on the multi-information dis-
play, read the message and follow the instructions.
■If the battery is discharged
The engine cannot be started using the
smart entry & start system. Refer to P.359to restart the engine.
■Electronic key battery depletion
 P. 1 0 0
■Conditions affecting operation
 P. 1 1 1
■Notes for the entry function
 P. 1 1 1
■Steering lock function
●After turning the engine switch off and opening and closing the doors, the
steering wheel will be locked due to
the steering lock function. Operating
the engine switch again automatically cancels the steering lock.
●When the steering lock cannot be released, “Locked. Push Ignition
Switch While Turning Steering Wheel”
will be displayed on the multi-informa- tion display.
Check that the shift lever is in P (auto-
matic transmission) or N (manual
Engine (ignition) switch
Performing the following oper-
ations when carrying the elec-
tronic key on your person
starts the engine or changes
engine switch modes.
Starting the engine

1404-2. Driving procedures
transmission). Press the engine
switch while turning the steering wheel left and right.
●To prevent the steering lock motor from overheating, operation of the
motor may be suspended if the engine
is turned on and off repeatedly in a short period of time. In this case,
refrain from operating the engine
switch. After about 10 seconds, the steering lock motor will resume func-
tioning.
■When “Keyless Access System
Disabled Check Owner's Manual” is displayed on the multi-information
display
The system may be malfunctioning. Have the vehicle inspected by any
authorized Toyota retailer or Toyota
authorized repairer, or any reliable repairer immediately.
■Electronic key battery
 P.316
■Operation of the engine switch
●If the switch is not pressed shortly and
firmly, the engine switch mode may
not change or the engine may not start.
●If attempting to restart the engine immediately after turning the engine
switch off, the engine may not start in
some cases. After turning the engine switch off, please wait more than 10
seconds before restarting the engine.
■If the smart entry & start system
has been disabled
If the smart entry & start system has been disabled, refer to P.357.
■Immediately after reconnecting the
battery terminals due to replacing the battery and so forth
The engine may not start. If this occurs,
turn the engine switch to ON, and start the engine after waiting at least 10 sec-
onds. Idling may be unstable immedi-
ately after the engine starts, however, this is not a malfunction.
WA R N I N G
■When starting the engine
Always start the engine while sitting in
the driver’s seat. Do not depress the accelerator pedal while starting the
engine under any circumstances.
Doing so may cause an accident resulting in death or serious injury.
■Caution while driving
If engine failure occurs while the vehi-
cle is moving, do not lock or open the
doors until the vehicle reaches a safe and complete stop. Activation of the
steering lock in this circumstance may
lead to an accident, resulting in death or serious injury.
NOTICE
■When starting the engine
●Do not race a cold engine.
●If the engine becomes difficult to
start or stalls frequently, have your vehicle checked by authorized
Toyota dealer or repairer, or another
duly qualifiedand equipped profes- sional immediately.
●Vehicles with an automatic trans-mission: Do not shi ft the shift lever
while the starter is operating.

1424-2. Driving procedures
time the switch is pressed.)
1 OFF*
The emergency flashers can be used.
2ACC
Some electrical components such as
the audio system can be used.
“ACCESSORY” will be displayed on the
meters.
3 ON
All electrical components can be used.
“IGNITION ON” will be displayed on the
meters.
*: Vehicles with an automatic transmis-
sion: If the shift lever is in a position
other than P when turning off the
engine, the engine switch will be
turned to ACC, not to off.
■Auto power off function
Automatic transmission: If the vehicle is
left in ACC for more than 20 minutes or
ON (the engine is not running) for more than an hour with the shift lever in P, the
engine switch will automatically turn off.
However, this function cannot entirely
prevent battery discharge. Do not leave the vehicle with the engine switch in
ACC or ON for long periods of time
when the engine is not running.
Manual transmission: If the vehicle is left
in ACC for more than 20 minutes or ON
(the engine is not running) for more than an hour, the engine switch will automati-
cally turn off. However, this function can-
not entirely prevent battery discharge. Do not leave the vehicle with the engine
switch in ACC or ON for long periods of
time when the engine is not running.
If the engine is stopped with the
shift lever in a position other than P,
the engine switch will not be turned
off but instead be turned to ACC.
Perform the following procedure to
turn the switch off:
1 Check that the parking brake is
set.
2 Shift the shift lever to P.
NOTICE
■To prevent battery discharge
●Do not leave the engine switch in
ACC or ON for long periods of time
without the engine running.
●If “ACCESSORY” or “IGNITION
ON” is displayed on the meters while the engine is not running, the
engine switch is not off. Exit the
vehicle after turning the engine switch off.
When stopping the engine
with the shift lever in a posi-
tion other than P (vehicles
with an automatic transmis-
sion)